Search Results

Search found 3061 results on 123 pages for 'sata hdd'.

Page 92/123 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• Server not responding to SSH and HTTP but ping works

  - by yes123

  Hello guys, I requested an hard reboot because none of ssh and http worked. Ping worked normally. Which logs should i check to understand what was the problem? Thanks! (debian 6 on lamp) Edit: my memory and swap: Mem: 4040068k total, 1114920k used, 2925148k free, 109212k buffers Swap: 1051384k total, 0k used, 1051384k free, 283820k cached 4 GB ram (and more than 1TB of HDD) The cause is from 2 days ago: look how the usage of swap goes +60% in less than 10hours My control panel reports this as top 5 memory usage process: If every apache2 process is 190MB large that sux because IF i do TOP i have 262 sleeping process most of them are apache2! My apache mpm_prefork settings are: <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 ServerLimit 1500 MaxClients 1500 MaxRequestsPerChild 2000 </IfModule> KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 4

  Read the article

• Time Machine Server on Fedora

  - by Conner Stephen McCabe

  I was just wondering if anyone knew how to/or knew of a good guide to setting up mac Time Machine backup server on a fedora 17 machine. I recently ran into an issue with my HDD and lost all of my data, so I don't want it to ever happen again, as it was quite traumatising, haha! I just want to be able to back all of my data up on my fedora machine from my mac, at scheduled times when I connect to my home network. If anyone could help, it would be fantastic, I searched around on google, but all of the ones I found were for older distros. Thanks guys!

  Read the article

• How to upgrade OS on Mac Mini with external USB Drive?

  - by David

  We have a G4 Mac Mini, circa 2005, running Mac OS X 10.4 Tiger, and we want to upgrade to 10.5 Leopard. We have a Leopard install disk, but the optical drive in this mini is broken. So we transferred the install disk image to a USB HDD, but now we can't figure out how to boot off it. From what I've read in Mac forums, some PPC Macs, including some G4's, have been able to boot from USB, even though it sounds like this wasn't officially supported, and it may well depend on the specific model of USB drive and Mac. My Mac says CPU is "PowerPC G4 (1.2)" and Boot ROM is "4.8.9f4". I was hoping I might just find somebody here who had that same Mac Mini and find out if they could make it work. I'd especially like to know any specifics about the USB drive they found success with. Any insights at all would be appreciated. Thanks.

  Read the article

• How to customize Windows 7 HAL library during installation (BSOD STOP: 0x000000A5)?

  - by koldovsky

  While trying to install Windows 7 x86 Ultimate on Samsung M40 laptop (Pentium M 1.7 Dothan, 2 GB RAM/ 100 GB HDD) i receive BSOD STOP: 0x000000A5: The bios in this system is not fully ACPI compliant. Please contact your system vendor for an updated bios. The bios on the system is updated to latest version. If ACPI is the real source of the issue it means that I possibly could use another HAL library. In Windows XP it is possible to install system with generic HAL library pressing F7 when installer asks to supply drivers, but on Windows 7 I can't find such option. Ironically, Vista installs and works nice, even if they said that Windows 7 is less demanding for hardware. Windows 7 Advisor also tells nothing suspicious. Can anybody tell me how to customize Windows 7 installer to use generic HAL library (if it is possible, of course) or point me to another solution?

  Read the article

• NVIDIA Driver Crashing on Custom-Built Windows 7 PC

  - by srunni

  I've got a custom-built PC with these specs: Fractal Design Define R3 ASUS P8Z77-V motherboard Intel Core i7-2700k with Thermalright HR-02 Macho Cooler NVIDIA GeForce GTX 560 with Arctic Cooling Accelero Twin Turbo II Cooler Crucial M4 128 GB SSD 1 TB Hitachi HDD G.SKILL Ares Series 2x8 GB RAM (x2) SeaSonic 520W PSU Windows 7 Ultimate SP1 (x64) NVIDIA driver version 301.42 Upon building the PC, I overclocked the CPU (but never the GPU), and there were no problems for 1-2 months. Then I started getting crashes with this error when doing anything that's computationally or graphically intensive: I un-overclocked the CPU, but that hasn't fixed anything. This is what the inside of my case looks like: I'd appreciate any guidance on resolving this problem. I did get some of the thermal paste on the graphics card when installing the aftermarket cooler, but there were no issues for a month or two. Update I did a clean install and the issue persisted - looks like it's a hardware issue. I will try removing/cleaning/reseating all the parts.

  Read the article

• Firewire 800 with Windows

  - by Amitesh

  I have two windows machine with windows server 2003 installed on them. I am running a Lab View script on 1 machine and storing the data. But since it has less memory, I want to transfer data to another machine using firewire 800. Is it possible to configure out the second machine just as an external HDD attached to it and write data directly to it? (This is possible with MACs) Dont want to use the ethernet (internet/ TCP/IP prot.) to transfer the data. Is it possible? Thanks.

  Read the article

• Which Windows OS Supports 8 GB RAM in a Laptop and Suggestions for a Better Laptop for Personal & De

  - by Ellen

  I am about to purchase a laptop and have zeroed on the following two of them. Toshiba L500-ST2544 Toshiba L505-ES5034 The Common Specification for both of them are as follows - RAM - 4GB DDR3 Memory HDD - 320 GB Processor - Intel® Core™ i3-330M Processor WebCam and Mic - Available HDMI Port - Available Numeric Key Pad - Available Windows 7 (64 bit) Home Premium Now, the only difference between ST2544 and ES5034 is that, the ST2544 has a maximum of 2 slots with 2 GB in each. So, you can have a max of 4 GB RAM in that. The ES5034 can support 8 GB RAM, so, in a couple of years, if I want to add another 4 GB RAM I will be able to do it. The price for ST2544 is USD 629.00 whereas, the price for a ES5034 is USD685. A difference is USD 55.00 (not a major amount, but still something extra). Is it worthwhile going for the ES5034? Which Windows Operating System supports 8 GB of RAM?

  Read the article

• Any Suggestions on How to Soup Up/ Mod a MacBook Pro 13"?

  - by 5arx

  So I've got a mid-2009 MacBook Pro 13". Integrated GPU so not a games machine but fast enough for doing .Net development in VMs. I love the little thing and wanted to give it a Christmas present so thought I'd mod it up a bit and give it a boost. I'm probably going to go for a 500GB Seagate Momentus XT hybrid drive rather than full-on SSD (I need 500GB space) but was wondering if there are any other mods/tweaks people could suggest? I saw something online about swapping a HDD for the DVD drive and wondered if anyone had tried this or similarly drastic mods to the smallest of the MBPs. Cheers.

  Read the article

• MySQL won't stop doing stuff

  - by Felix

  Sorry for the title of the question, here's my problem: I've been trying to set up some scripts that import a lot of stuff hourly from an external source. They seemed to work fine, so I set up a cronjob to run them every hour. One day later I find six or seven instances of that script just hogging the MySQL server, making it unresponsive. I killed their processes, but MySQL was still not responding. I had to kill MySQL, reboot and then MySQL started working again (who knows on what) and being unresponsive (yes, I did remove the scripts from the cronjobs). I SHOW PROCESSLISTed and killed every process I could find. Still nothing, MySQL is hogging the HDD and is at the top of top and making the server load go up in the sky. I don't know what to do, if I kill and start it again it will probably do the same thing. What should I do?

  Read the article

• Operating System Not Found - BIOS recognizes, Live OS doesn't (Laptop)

  - by Klaus Borges

  Here's the deal: I have a multi-partitioned hard drive on my laptop set up with GRUB. I got a blue-screen while working on Windows 7 and when rebooting I got the Operating System Not Found error message. I rebooted the computer once again and entered the BIOS setup just to see if recognized my HDD - it did. Next step for me was booting a Live CD and seeing if I could repair GRUB or at least check if something changed on the partitions, but it doesn't seem to recognize anything there. Tried blkid, fdisk -l, not even GParted can see it. What should I do?

  Read the article

• Writing to external drive runs out of space prematurely

  - by steve

  I have a USB 2.0, 500 GB HDD. I am writing a bunch of data to it, that I previously recovered from the drive. I have formatted the drive in exFAT, since the drive will be used with Windows and OSX. At first, I tried using Windows explorer to move the files over to the drive (about 160 GiB worth) but after copying about 30% of the data (according to TeraCopy), Windows Explorer reported the drive as out of space, and that it was completely full. WinDirStat only showed the size of data that had been copied over... Where did this extra space go? Why is there a 300+ GiB discrepancy between the usage reported by the files and what Explorer sees?

  Read the article

• Serve my website from different server during downtime

  - by nfedyashev.mp

  I have a VPS server running in the cloud. Fully automated server image upgrade/downgrade(by RAM/HDD plans). The problem is that server upgrade/downgrade takes time and involves total unavailability during this period(up to 30 minutes). Goal: during this downtime server my website(http://mydomain.here) from different server with some message like "Under construction". How can I do this? -- mydomain.here is hosted on godaddy and uses its DNS(If I call it right). It's pointing with A-record to my VPS's IP address now. Change in these DNS settings will take more than 30minutes, so it's not an option. How can I find mode "dynamic" DNS? What should I learn?

  Read the article

• Very slow Windows 7 on Thinkpad T61

  - by bogdanf

  I have a very strange problem with my fresh install of Windows 7 Profesional, 64bits on my Lenovo Thinkpad T61 : The overal performance is very slow, the disk is constantly spinning, even without any program running (after boot, no other programs installed). The boot process is very slow itself (4-5 minutes). I mention that the laptop was fine on XP until the upgrade. Thanks ! Additional info (as requested by the comments) : 2GB RAM Yes, I added all the manufacturer (Lenovo) drivers and updates (using the utility provided by Lenovo) Tried with both 32 and 64 bits editions. The 32 bits one is performing a little better, but not very usable either. The hdd has enough space (20 GB or so) The problem is still present on a fresh install, so no recycle bin emptying or unistall programs (there aren't any except plain 7) would help. I'm not a newbie, so no obvious causes are left unchecked

  Read the article

• PC boots on then off & 30 sec. later on again, it wiil shut off on itself mostly in idle or just unexpecticly

  - by Jody

  This problem started w/ my sons desktop, it would just shut off after a bit of work or stay on for a long time & to get it to unfreeze is to cold boot it, i put a new HDD in & I still have the same issue, RAM is good power supply fan is moving quite as well as all the rest of the fans it has stayed fairly dust free, i'm at a loss ,I have defaulted all the factory settings changed battery & ungraded to a new OS. I still have the same problem. the power light stays on after it has shut down & when upon starting it goes straight to safe mode option page, I start in last good config. reboots again takes 30 sec. to boot & will work again for a while, the only other thing I haven't tried was a graphic card replace, i'm onboard video now & have been.

  Read the article

• recommendations for a lightweight linux distribution for a test server

  - by Jack

  I'm planning on setting up a test server to experiment with some application servers (tomcat/jboss/...) and with some portals. Now the machine I've set aside for this is lightweight CPU/GPU wise(Atom D510, 4 gigabyte ram, 500 GiB hdd, onboard GPU). But it should suffice for most things, I'm more interested in the stability of JBoss/Tomcat for my purposes than the stability. However I'm having a bit of trouble picking an appropriate distribution size/performance/setup time wise/security wise since it seems I can't sneeze without another distribution popping up. I've been thinking about going for Fedora since I've read that that distribution has been optimized for Atom, but I'm not really familiar with it. My experience with Linux has mostly been limited to Ubuntu and some tinkering with puppylinux. I'm not afraid to get my hands dirty using the command line. I'm not planning on starting a discussion per se, mostly the pros/cons that people have encountered with some distributions

  Read the article

• LVM, Soft RAID1, and Replication?

  - by mtkoan

  Hi all, I am practicing putting together a HA file server. It is a linux server with 2 1.5TB Hard drives. My plan is to use LVM to manage the physical volumes into logical volumes for /, /home, and /var. Then use md (soft RAID 1) to mirror the image onto the second HDD, THEN use DRDB to mirror the entire setup another server. Is this overkill? Would I just be okay with just md and DRDB? The system will serve user's homedirs (~100) and probably some groupware or other local intranet. On my own machines I've always separated root and /home partitions in case I break something, I can easily reinstall the OS. Should I follow that same theory here? If so I need LVM, because I really can't predict where we'll need more space, /var or /home.

  Read the article

• Fujitsu Siemens V6535 laptop doesn't wake up - crash when going into standby?

  - by marc

  I'm having trouble with my laptop (Fujitsu Siemens model V6535). It runs Windows 7, and after I upgraded from Vista I've noticed something that makes me really angry. When my laptop goes into Standby, the power LED changes to red and starts blinking (standby mode). When I push the power button to wake it up it, the blinking LED changes to green but nothing else happens. Nothing on the display, no HDD sound. When I press the power button for a few seconds and then try turn it on again, it doesn't display anything. I have to unplug the charger, shut it off, and power it on again without the power cable. Then it starts working. A few days ago I upgraded the BIOS to the newest version, but it doesn't help. Does anyone have any idea what can be wrong?

  Read the article

• Is a PCIE X1 card for USB 3.0 worth it?

  - by lelouch

  I have a portable HDD on USB 3.0, and soon I'll have a 32gb flash drive on USB 3.0 as well. My motherboard is pretty old - and the next time I'll upgrade it is when I get a new CPU/mobo/ram. Slots on my mobo: PCIE X16 - For my GTX 260 2xPCI PCIE X1 I'm considering purchasing a PCI express X1 card like this - http://www.ebay.com.au/itm/PC-Laptop-2-USB3-0-Ports-PCI-E-PCI-Express-X1-Card-New-/280772000446?pt=AU_Networking&hash=item415f50babe Now the question: What are realistic (read/write) speeds I'll get in this setup, assuming I have 1 USB 3 device connected at a time, and the bottleneck is the PCIE?

  Read the article

• TrueCrypt-ed Windows XP reseting administrative password

  - by Predrag Punosevac

  I have inherited a laptop running Windows XP 64bit professional from a former system admin of my Lab. The laptop is encrypted with TrueCrypt and luckily I have a password for TrueCrypt and can boot and login into the guest account. However this is where my problems starts. There are four account on the laptop three of which do have administrative privileges. However nobody of two formers members of the lab and one current member remember their passwords. I was given the assignment of recovering 2TB of data from that laptop. How does one go about reseting administrative password in Windows in particularly in the presence of TrueCrypt? If you are wondering I have never used Windows in my life so the only thing I usually with any Windows machine is just wipe out entire HDD and install OpenBSD.

  Read the article

• md5sum of large files gives different results sometimes

  - by Emanuele

  I have an AMD quad core, 8 gb RAM, 1 SSD EXT2 (2 months old), 2 HDD EXT4, approximately 1 year old. I'm using Ubuntu 10.04 x86-64 and when I compute the md5sum of large files (9 GB) sometimes I get different values than the one stored on a reference file. Upon restarting and switching off the PC then I get the expected results no matter how many times I repeat it. But this is random. I've turn on ECC (the fastest possible settings) and the issue seems to be rarer, but I've run memtest86+ for 6+ hours without a glitch (and with ECC off!). Any idea? Should I update the BIOS of my motherboard (Asus EVO-something...don't remember it now)? I've tried all the rest apart this, but genuinely don't know what to do anymore... Any suggestion is appreciated!

  Read the article

• Streaming audio to headless linux box

  - by Ralph

  I have a dual boot (Win 7 + Ubuntu) PC connected via wifi with my music collection on a local HDD. I usually use Rhythmbox on Ubuntu or Winamp on Windows to listen to my music but I'll change if I have to. I also have a Raspberry Pi (low power PC running Debian) in the living room that is usually headless and connected via ethernet. The Raspberry Pi is also connected to my living room speakers via an amp. I would like to be able to stream music from my PC over the network to the linux raspberry pi. What software can I use to do this? Some sort of audio client\server?

  Read the article

• HP Pavillion dv6 laptop - 15 beeps on startup and a black screen?

  - by dunc

  Usual story - girlfriend's step-brother's laptop is broken. I don't know a huge amount about what occurred before it broke, but I do know the following: When you try to turn the laptop on, it beeps 15 times exactly. The screen remains black. The LED on the Caps Lock key flashes continuously. If left on, the laptop never boots - as far as I can see. If left on, on a stable surface with decent ventilation for a relatively short period of time, the laptop (below keyboard, but not where the RAM/HDD are) gets very hot. I've tried doing what most websites appear to recommend for similar problems, which is to disconnect AC and battery then hold the power button down for a minute before reconnecting the AC and trying to turn the laptop on - no difference. EDIT I've also tried re-seating the RAM, to no avail. Any ideas? Thanks in advance,

  Read the article

• Smart backup software

  - by gisek

  I use a laptop on daily basis. As I have a lot of important data there it would be nice to do backups of some directories every day. Can you recommend a specific application that would take care of it? Maybe there is an app that would instantly commit changes I make in a directory on my laptop to the backup folder? The important thing is that I have some big files (a few GB's) that have some minor changes very often. I'm talking about VirtualBox disk images. It would be nice if the software could handle it smartly. Also notice that I'd like to store it on an external usb HDD, which sometimes isn't plugged in.

  Read the article

• Why does Windows 7 x64 work faster than an x86 edition on my PC?

  - by Jasper

  Why does Windows 7 x64 work faster than an x86 edition on my PC even though I mostly use x86 things in it? What's wrong with me, and what am I missing? Majority of the things I use is x86 (e.g. DAWs, games, media players). A considerable amount of them, however, are x64 (although their x86 counterparts work just fine). I've tried using the same things on the same system but always ended up finding Windows 7 x64 working slightly faster than x86. I'm very observant. I even notice the tiniest window animations. System: Windows 7 Ultimate x64 CPU: Intel Core 2 Duo E7500 @ 2.93 GHz RAM: 2 GB x 2 = 4 GB DDR2 @ 332 MHz Motherboard: Intel D945GCNL Graphics: ATI Radeon HD 4350 @ 1 GB Dedicated Audio: M-Audio FastTrack Pro HDD: Samsung HD753LJ 733 GB & Samsung HD160JJ 156 GB As you can see, my system is old.

  Read the article

• Truecrypt system partion partially encryted but then drive corrupted and won't boot - decrypting so I can access files to backup?

  - by Dr.Seuss

  So I was attempting to encrypt my (Windows 7) system drive with Truecrypt and it stopped at around 15% and said that there was a segment error and that it could not proceed until it was fixed. So, I restarted the computer and ran HDD Regenerator which subsequently fixed the bad sectors on the drive, but now my system cannot boot. So, I run a number of recovery disks to no avail (Windows repair is unable to fix) and the drive won't mount on a linux version run from a CD because the drive is encrypted. So I tried mounting the drive using Truecrypt under the Linux distribution on the disk and selected "Mount partition using system encryption without pre-boot authentication" so I can decrypt, but I get an error message about it only being possible once the entire system is encrypted. How do I get out of this mess? I need to be able to back up the data that's on that partially encrypted drive so I can reinstall my operating system.

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >