Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 92/370 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• What's wrong with my custom patch cables?

  - by stu42j

  I have a box of bulk Cat5e riser cable left over from when I had my house wired. I figured I could use this to make some custom length cables for connecting my computers, switches, etc. I had a crimper already so I bought a bag of RJ45 plugs. I made a few cables several years ago, but my experience/knowledge with this sort of thing is minimal. None of my cables are working. I don't have a tester so I just plug the cable into a computer and switch but I get no link light. I wired them them all straight-through and visual inspection doesn't show any problems. Any ideas what I might be doing wrong?

  Read the article

• Cisco ASA intermittently fails to see traffic

  - by DrStalker

  users | Mikrotik -- Internet | ASA | ServerA and ServerB I'm trying to troubleshoot a problem with a new Cisco ASA 5505. The network design is as above - the Microtik is the existing router, ServerA and ServerB used to plug directly into it. ServerA has IP 10.30.1.10, ServerB has IP 10.30.1.11 The ASA is configured with no NAT, a "allow anything" firewall, and uses the microtik as its default gateway. In effect, it is currently a simple IP router; the firewall and VPN stuff will all come later once the basics are working. Th problem is access to ServerA and ServerB is erratic - sometimes it will work, sometimes it will fail. It can fail for either one of the servers only, or both. When it is working: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show the incoming connections. When it is failing: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show nothing reaching the ASA. This can fail for one server only (e.g.: the Mikrotik is putting out packets to 10.30.1.10 and 10.30.1.11, but the ASA is only seeing packets arrive destined for 10.30.1.11) It can fail for one source only (e.g.: ClientA on the users network can ping 10.30.1.11, but clientB cannot) The problem can also be seen from the mikrotik router itself; sometimes it can ping ServerA and ServerB, sometimes it can only ping one of them What could be causing this? I can't think of any possible cause that is intermittent and could explain why the problem may occur for one destination server and not others. edit: Link to ASA config

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by bakytn

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed)

  Read the article

• Dell Studio 15 Broadcom wireless drivers not working in Linux Mint

  - by dcd0687

  I installed Linux Mint 12 on my Dell Studio 15 and everything worked perfectly up until I tried updating the STA Driver for the Broadcom (BCM4312) wireless controller. I've tried these bash commands in order and I still don't have wireless. sudo apt-get install b43-fwcutter sudo apt-get install b43-fwcutter firmware-b43-installer I've also tried uninstalling everything with synaptic package manager including broadcom-sta-common and broadcom-sta-source, then restarting and running the above commands which didn't work either. What's the best way to do this on a Dell Studio 15?

  Read the article

• Campus Network Design - Firewalls

  - by user3081239

  I am designing a campus network, and the design looks like this: LINX is The London Internet Exchange and JANET is Joint Academic Network. My goal is an almost-fully redundant with high availability, because it will have to support about 15k people, including academic staff, administrative staff and students. I have read some documents in the process , but I am still not sure about some aspects. I want to dedicate this one to firewalls: what are the driving factors in deciding to employ a dedicated firewall, instead of an embedded firewall in the border router? From what I can see, an embedded firewall has these advantages: Easier to maintain Better integration One less hop Less space requirement Cheaper Dedicated firewall has the advantage of being modular. Is there anything else? What am I missing?

  Read the article

• How do I locate the app generating this network traffic?

  - by Christopher Bartels

  I don't know what this process is doing on my computer. I run Windows 7 Professional w/ all its updates running current non-free antivirus. I only see it in Resource Monitor, where you can see the Network Service process connected to bitum.nnov.ru. When my PC's network traffic generating apps are idle, this process is using the most of all the idle processes using the network. Screenshot hosted here: http://sss.proinbox.com/bitum-nnov-ru.jpg Does anyone recognize this? The page source mentions a control port & a stream port: Page Source for http://bitum.nnov.ru : <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <title>DVR WebViewer</title> <meta http-equiv="Content-Type" content="text/html; charset=euc-kr"> </head> <body topmargin="0" leftmargin="0"> <OBJECT classid="clsid:EE479A40-C128-40DD-93DA-000556AF9607" codebase="CtrWeb.cab#version=1,0,2,2" width=875 height=585 align=center hspace=0 vspace=0 > <param name="CmdPort" value="5920"> <param name="StreamPort" value="5921"> </body> </html> When I google this page's title, I see a number of other domains that host the same page. Whois: domain: NNOV.RU nserver: ns.kis.ru. nserver: ns.nnov.ru. 78.25.80.210 nserver: ns1.kis.ru. nserver: ns2.kis.ru. state: REGISTERED, DELEGATED, VERIFIED org: "Agentstvo Delovoj Svjazi", Ltd registrar: RU-CENTER-REG-RIPN admin-contact: https://www.nic.ru/whois created: 1996.10.23 paid-till: 2012.11.01 free-date: 2012.12.02 source: TCI Last updated on 2012.06.16 04:20:46 MSK

  Read the article

• Sonicwall routing between multiple subnets on multiple interfaces

  - by Rain

  As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

  Read the article

• Delaying NIS & NFS startup till after network interface is fully ready on Fedora 17

  - by obmarg

  I've recently set up a fedora 17 server for our network, and I've been having trouble getting the NIS service to work on startup. Here's some logs from the system: Aug 21 12:57:12 cairnwell ypbind-pre-setdomain[718]: Setting NIS domain: 'indigo-nis' (environment variable) Aug 21 12:57:13 cairnwell ypbind: Binding NIS service Aug 21 12:57:13 cairnwell rpc.statd[730]: Unable to prune capability 0 from bounding set: Operation not permitted Aug 21 12:57:13 cairnwell systemd[1]: nfs-lock.service: control process exited, code=exited status=1 Aug 21 12:57:13 cairnwell systemd[1]: Unit nfs-lock.service entered failed state. Aug 21 12:57:14 cairnwell setroubleshoot: SELinux is preventing /usr/sbin/rpc.statd from using the setpcap capability. For complete SELinux messages. run sealert -l 024bba8a-b0ef-43dc-b195-5c9a2d4c4d41 Aug 21 12:57:15 cairnwell kernel: [ 18.822282] bnx2 0000:02:00.0: em1: NIC Copper Link is Up, 1000 Mbps full duplex Aug 21 12:57:15 cairnwell kernel: [ 18.822925] ADDRCONF(NETDEV_CHANGE): em1: link becomes ready Aug 21 12:57:15 cairnwell NetworkManager[621]: <info> (em1): carrier now ON (device state 20) Aug 21 12:57:15 cairnwell NetworkManager[621]: <info> (em1): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] Aug 21 12:57:15 cairnwell NetworkManager[621]: <info> Auto-activating connection 'System em1'. Aug 21 12:57:15 cairnwell NetworkManager[621]: <info> Activation (em1) starting connection 'System em1' Aug 21 12:57:15 cairnwell NetworkManager[621]: <info> (em1): device state change: disconnected -> prepare (reason 'none') [30 40 0] ....... Aug 21 12:57:19 cairnwell sendmail[790]: YPBINDPROC_DOMAIN: Domain not bound Aug 21 12:57:26 cairnwell sendmail[790]: YPBINDPROC_DOMAIN: Domain not bound Aug 21 12:57:31 cairnwell sendmail[790]: YPBINDPROC_DOMAIN: Domain not bound Aug 21 12:57:35 cairnwell sendmail[790]: YPBINDPROC_DOMAIN: Domain not bound Aug 21 12:58:00 cairnwell ypbind: Binding took 47 seconds Aug 21 12:58:00 cairnwell ypbind: NIS server for domain indigo-nis is not responding. Aug 21 12:58:01 cairnwell ypbind: Killing ypbind with PID 733. Aug 21 12:58:01 cairnwell ypbind-post-waitbind[734]: /usr/lib/ypbind/ypbind-post-waitbind: line 51: kill: SIGTERM: invalid signal specification Aug 21 12:58:01 cairnwell systemd[1]: ypbind.service: control process exited, code=exited status=1 Aug 21 12:58:01 cairnwell systemd[1]: Unit ypbind.service entered failed state. By the looks of these logs the ypbind service is starting up at 12:57:12 but the network interface isn't coming up till 12:57:15. My guess is that this is causing ypbind to time out when trying to connect. As a knock-on effect the NIS failure is causing problems with NFS which is no longer able to map UIDs properly. This problem doesn't seem to be fixed by actually starting ypbind etc. so I've had to set all my NFS shares to noauto. I have tried manually adding NETWORKDELAY and NETWORKWAIT in /etc/sysconfig/network and also running systemctl enable NetworkManager-wait-online.service as I've seen suggested in some places, but neither of these have had any effect. It is relatively easy to fix manually by restarting ypbind & mounting NFS shares after the network has started up, but it's less than ideal to have to do this every time the server has been rebooted. Does anyone know of an easy (and preferably hack-free) way of delaying the ypbind startup till after the network interface is fully ready?

  Read the article

• OpenVPN DNS: VPN DNS stomping local VPN

  - by Eddie Parker

  I've finally noodled with OpenVPN enough to get it working. Even better, I can mount samba drives, ping network machines through the TUN device, etc - it's all great. However, I'm noticing that if I use the following directive, then some of the machines that are normally visible by the client, on the client's side (i.e., not through the VPN) get masked with some other server out on the Internet. push "dhcp-option DNS 10.0.1.1" # Push our local DNS to clients Is there any way to avoid this, besides hacking the 'hosts' file on the client machine? Ideally I'd like to only use my VPN's DNS for machines within that domain.

  Read the article

• Ad-hoc connection between iPhone and Macbook Pro

  - by Phil Nash

  I sometimes find it useful to connect my iPhone to my Macbook Pro by creating an ad-hoc wireless network from the MBP and connecting to that from the iPhone. However, what I find is that sometimes this works and sometimes it doesn't. When it's not working the symptoms are usually that I see the ad-hoc SSID in the list of available networks on the iPhone, can connect to it from there (including entering my WEP key), and it shows up as the wifi network in use. However I don't get the wifi symbol in the taskbar (it remains as 3G) and attempting to use the connection (e.g. trying to connect to iTunes or Keynote using their respective Remote apps) fails saying that there is so wifi connection. I've tried rebooting both the iPhone and the MBP, recreating networks with different SSIDs and tried different channels - all to no avail! I'm especially puzzled that (a) sometimes it works just fine first time and (b) the Settings app seems to think its all connected fine. Is there anything else I should be trying?

  Read the article

• How to hack airport extreme to support USB 3G modem?

  - by Mike Caron

  Has anyone out there ever tried to hack the Airport Extreme, specifically with regard to the USB port? There are many cellular routers available that provide WiFi sharing of a USB modem link. However, instead of buying yet another router, I'd like to use my expensive Airport Extreme with it. The AE has a USB port on the back, but it's been said that it only talks to printers. Is there a way to hack the USB driver on the AE to allow it to recognize a USB modem, then use that as the connectivity instead of the LAN? I would imagine that one could use OpenFirmware to boot something on the AE. If one can boot it, then one could provide access using SSH across the lan. Once access is granted, then let the hacking begin... but I don't know how to (a) get the mini-osx on to USB (is it the same as the ATV without a UI?) or (b) how to load up certain things once boot has begun.

  Read the article

• How to copy lots of files between two computers, without network?

  - by Steve Bennett

  I want to copy around 50Gb of files from my desktop to my work laptop. For some reason, the laptop won't connect to my home network. I haven't had any luck with a direct ethernet connection either, and I'm not willing to change any of the laptop's network configuration (last time I did that, I couldn't get onto the network at work, making me Not Very Popular). So...what else is there? The obvious route is copying via SD card. My largest card is 8Gb. But I can't find a good workflow. Is there a tool designed for this, where I could just repetitively move the card back and forth, without having to select files? I've tried using teracopy, but you end up missing a few files. I guess I could zip everything up into multi-volume .rars or something...but is there a more elegant way?

  Read the article

• Software to consolidate contacts from multiple sources?

  - by Neil

  I'm looking for an app that can take my contacts from Gmail, Facebook, and my mobile phone, to come up with one consolidated address book that, for each contact, contains the name, email address, facebook username, and mobile number, and if possible, export this data to the Mac Address Book. Is there any app that can do this? Online or offline will do. Currently, I've been only able to find apps that need to be hosted on my own server, such as the ones below. Isn't there any standalone desktop or web app? knowee[dot]net/ noserub[dot]com/ diso-project[dot]org/

  Read the article

• Dell Inspiron 1520 Intermittent connection to wireless router

  - by ChuckNevol

  I have two computers in my home which are connected to a wireless router and a wireless printer. One computer is a Del XPS and the other a Dell laptop Inspiron 1520. In recent weeks we noticed the Inspiron had difficulty maintaining connection to the wireless router - web pages would suddenly have to be reloaded, or the computer rebooted while the other computer, the XPS, had no problems on the same network. So we connected a hard wire line from the Inspiron to the Verizon supplied wireless router. Problems still exist. could it be a bad driver?

  Read the article

• VPN for a small organization

  - by user24091

  I am in charge of a small office network that has < 10 users. I want to be able to offer them access to the network from their home internet connections. At the moment we have a regular ADSL-router-firewall to provide local network access and a fixed IP address. I know there are enterprise-level VPN solutions, but these obviously won't be available to us because of the cost and complexity. What small-scale solutions are around that you could recommend, what would we need to deploy on the client side, and what would the clients need to do to access the VPN? Simplicity and low cost need to be the keys here. Thanks

  Read the article

• Finding cause of TCP retransmission within a LAN

  - by Surreal

  Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

  Read the article

• Reaver keeps reapeating the same PIN

  - by Umair Ayub

  I have been trying to Hack a WPA2 Wifi and so far I am stuck with it. Problem is that it keeps trying same pin over and over again. Here is the last REAVER command I entered. reaver -i mon0 -b 2C:AB:25:51:F1:CF -vv -c 1 -S -L -f It does this (only one PIN again and again) [+] Switching mon0 to channel 1 [+] Waiting for beacon from 2C:AB:25:51:F1:CF [+] Associated with 2C:AB:25:51:F1:CF (ESSID: PTCL-BB) [+] Trying pin 12345670 [+] Sending EAPOL START request [+] Received identity request [+] Sending identity response [!] WARNING: Receive timeout occurred [+] Sending WSC NACK [!] WPS transaction failed (code: 0x02), re-trying last pin [+] Trying pin 12345670 [+] Sending EAPOL START request [+] Received identity request [+] Sending identity response [+] Received identity request [+] Sending identity response ^C [+] Nothing done, nothing to save.

  Read the article

• Enable SMB file sharing on OS X - "Incorrect Password"

  - by Tim Robinson

  I have a Mac running Snow Leopard connected to an Active Directory domain. I can share folders on the Mac and view files from Windows without problems. When I try to enable my Mac account for write access through System Preferences, I'm prompted for my account's password. Even though I'm entering the right one, I get an "Incorrect Password" response. The same process works fine for the local Mac administrator account; it's the Active Directory account I'm having problems with. I followed the advice on this page on apple.com without success: (I used the Mac to reset my domain password, and re-created my login keychain) If you want to use a user account that existed before you installed Mac OS X 10.3 (Panther), you may need to reset the password for the account using Accounts preferences. Can anyone suggest what might be wrong? Until I fix this I can't write to my Mac file share from Windows.

  Read the article

• iPod touch has extremely slow wifi, drops packets - only on my router

  - by mskfisher

  I just purchased an iPod Touch. I am having a lot of trouble with its speeds on my Tenda W311R, but it has no speed problems on my neighbor's Netgear router. It will connect and authenticate to my network, but the Speed Test app from speedtest.net shows rates near 20-50 kbps. If I run the speed test immediately after powering the iPod on, it will get speeds of 10-20 Mbps, like it should - but the speeds slow down to the kbps range abut 10-15 seconds afterward. I get the same behavior with encryption and without encryption, and regardless of N, G, or B compatibility settings in the router. I've tried rebooting the iPod and resetting the network settings, but it's still slow. I've tried pinging the iPod from another computer, and it shows about 40% packet loss: $ ping 192.168.0.111 PING 192.168.0.111 (192.168.0.111): 56 data bytes 64 bytes from 192.168.0.111: icmp_seq=0 ttl=64 time=14.188 ms 64 bytes from 192.168.0.111: icmp_seq=1 ttl=64 time=11.556 ms 64 bytes from 192.168.0.111: icmp_seq=2 ttl=64 time=5.675 ms 64 bytes from 192.168.0.111: icmp_seq=3 ttl=64 time=5.721 ms Request timeout for icmp_seq 4 64 bytes from 192.168.0.111: icmp_seq=5 ttl=64 time=6.491 ms Request timeout for icmp_seq 6 64 bytes from 192.168.0.111: icmp_seq=7 ttl=64 time=8.065 ms Request timeout for icmp_seq 8 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 64 bytes from 192.168.0.111: icmp_seq=11 ttl=64 time=9.605 ms Signal strength is good - I'm never more than 20 feet from my access point, and it exhibits the same behavior if I'm standing next to the router. It works just well enough to receive text, but videos don't work at all. App downloads are hit and miss. I've tweaked just about all of the settings I can see to tweak, and I'm at a loss. I have also been searching Google for the past three days, all to no avail. Any suggestions?

  Read the article

• Seeing 10.x.x.x addresses in my BitTorrent client

  - by Legend

  Off late, I am seeing a number of IP addresses starting with 10.x.x.x in my bittorrent peer list. Aren't these IP addresses supposed to be private ones? I don't understand how I am able to see the IP address instead of the WAN (external IP) of the client... Any one knows why?

  Read the article

• Mac OS X: How do I disable SSID Broadcasting with Internet Sharing over Airport?

  - by Jack Chu

  I'm currently using Internet Sharing from my Ethernet over Airport on my Macbook Pro, however I don't want my SSID broadcasted†. There doesn't seem to be an option in Sharing/System Preferences to hide my ssid or prevent broadcasting. Any ideas? † My parent's restaurant has a wifi router, but it's on the roof level where the cable was installed. The signal it gets is weak, but works for the macbook. Their iPhones and 802.11G based computers can't get the wifi connection, maybe 802.11N on the macbook gets better penetration. I figure they could use the airport sharing from the laptop. For a restaurant type setting I don't think having WPA or WPA2 is super important. There's nothing sensitive or insecure on the network, so I figure hiding the SSID would be good enough for their purposes. It's not even active 100% of the time.

  Read the article

• How to stop intermittent playback on airtunes (iTunes + Airport Express)?

  - by Alex B

  Is there a definitive answer for how to stop intermittent "skips" or pauses while playing music from iTunes to an airport express connected to my home stereo? When I read other forums I see a wealth of posts that say "I did XYZ and it's fixed" followed by "I tried XYZ and it didn't work." This does not appear to be signal strength related. The green light on the Airport Express does not turn to yellow/orange. Other wireless devices have no trouble connecting at the same or greater distances from the wireless router.

  Read the article

• How do I use a Zyxel P660 router as just modem so that I can connect a WRT54GL router in cascade?

  - by Kenji Kina

  I have a Zyxel P660HW-t1 v2 router (which has a DSL port) and a WRT54GL router (which does not) and the exact same situation as in this thread (UPDATE: the connection between both devices is the important part, since I have been able to set the zyxel router to act as bridge by itself quite nicely. I have accessed my internet connection directly through a PC using PPPoE without any problems, the issues arise when I try to connect the WRT54GL router between the zyxel "modem" and my PCs). I've been trying to use my Zyxel P660 as a modem only: Setup P660 to bridge mode. Changed WRT54GL's IP address to 192.168.2.1 to avoid a conflict on the network. Configured the PPPoE settings as required on WRT54GL. The thing is that when I connect the Zyxel modem/router on the WRT54GL's internet port the light doesn't turn on. I can confirm that this port has been working ok, so I'm not really sure what's going between the devices. I checked several settings such as IPs, tried disabling DHCP on Zyxel/Linksys, Firewall on both and still nothing. Also, I tried connecting Zyxel directly to a computer in bridge mode and dialed successfully. I have even posted a question here before, thinking that what I asked there was the only thing I needed to get things done. Unfortunately it wasn't, and the guy that solved his issue didn't give enough details in his post (and is quite unlikely to give more details since he was an anonymous user). For one, I don't know how to do this part: connected to the Zyxel through telnet and forced LAN port 1 to be at 100mb as well I can't find the option that does this on the zyxel router. Not through telnet or the web admin. Can anyone help me solve this?

  Read the article

• openvpn: after changing to server mode, client does not create TUN device

  - by lurscher

  i had a previously working configuration with the config files used in a previous question However, i've changed this now to the following configuration using server mode, everything on the logs seem fine, however the client doesn't create any tun interface, so i don't have anything to connect to, presumably, i need to add or push some route commands, but i don't have any idea at this point what i need to do. I am posting all my relevant configuration files server.conf: dev tun server 10.8.117.0 255.255.255.0 ifconfig-pool-persist ipp.txt tls-server dh /home/lurscher/keys/dh1024.pem ca /home/lurscher/keys/ca.crt cert /home/lurscher/keys/vpnCh8TestServer.crt key /home/lurscher/keys/vpnCh8TestServer.key status openvpn-status.log log openvpn.log comp-lzo verb 3 and client.conf: dev tun remote my.server.com tls-client ca /home/chuckq/keys/ca.crt cert /home/chuckq/keys/vpnCh8TestClient.crt key /home/chuckq/keys/vpnCh8TestClient.key ns-cert-type server ; port 1194 ; user nobody ; group nogroup status openvpn-status.log log openvpn.log comp-lzo verb 3 the server ifconfig shows a tun device: tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.117.1 P-t-P:10.8.117.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) However the client ifconfig does not show any tun interface! $ ifconfig tun0 tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 POINTOPOINT NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) the client log says: Tue May 17 23:27:09 2011 OpenVPN 2.1.0 i686-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 12 2010 Tue May 17 23:27:09 2011 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue May 17 23:27:09 2011 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Tue May 17 23:27:09 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue May 17 23:27:09 2011 LZO compression initialized Tue May 17 23:27:09 2011 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:27:09 2011 TUN/TAP device tun0 opened Tue May 17 23:27:09 2011 TUN/TAP TX queue length set to 100 Tue May 17 23:27:09 2011 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:27:09 2011 Local Options hash (VER=V4): '41690919' Tue May 17 23:27:09 2011 Expected Remote Options hash (VER=V4): '530fdded' Tue May 17 23:27:09 2011 Socket Buffers: R=[114688->131072] S=[114688->131072] Tue May 17 23:27:09 2011 UDPv4 link local (bound): [undef] Tue May 17 23:27:09 2011 UDPv4 link remote: [AF_INET]192.168.0.101:1194 Tue May 17 23:27:09 2011 TLS: Initial packet from [AF_INET]192.168.0.101:1194, sid=8e8bdc33 f4275407 Tue May 17 23:27:09 2011 VERIFY OK: depth=1, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:09 2011 VERIFY OK: nsCertType=SERVER Tue May 17 23:27:09 2011 VERIFY OK: depth=0, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=vpnCh8TestServer/name=lurscher/[email protected] Tue May 17 23:27:09 2011 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:09 2011 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:09 2011 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:09 2011 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:09 2011 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue May 17 23:27:09 2011 [vpnCh8TestServer] Peer Connection Initiated with [AF_INET]192.168.0.101:1194 Tue May 17 23:27:10 2011 Initialization Sequence Completed the client status log: OpenVPN STATISTICS Updated,Tue May 17 23:30:09 2011 TUN/TAP read bytes,0 TUN/TAP write bytes,0 TCP/UDP read bytes,5604 TCP/UDP write bytes,4244 Auth read bytes,0 pre-compress bytes,0 post-compress bytes,0 pre-decompress bytes,0 post-decompress bytes,0 END and the server log says: Tue May 17 23:18:25 2011 OpenVPN 2.1.0 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 12 2010 Tue May 17 23:18:25 2011 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue May 17 23:18:25 2011 WARNING: --keepalive option is missing from server config Tue May 17 23:18:25 2011 NOTE: your local LAN uses the extremely common subnet address 192.168.0.x or 192.168.1.x. Be aware that this might create routing conflicts if you connect to the VPN server from public locations such as internet cafes that use the same subnet. Tue May 17 23:18:25 2011 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Tue May 17 23:18:25 2011 Diffie-Hellman initialized with 1024 bit key Tue May 17 23:18:25 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue May 17 23:18:25 2011 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:18:25 2011 ROUTE default_gateway=192.168.0.1 Tue May 17 23:18:25 2011 TUN/TAP device tun0 opened Tue May 17 23:18:25 2011 TUN/TAP TX queue length set to 100 Tue May 17 23:18:25 2011 /sbin/ifconfig tun0 10.8.117.1 pointopoint 10.8.117.2 mtu 1500 Tue May 17 23:18:25 2011 /sbin/route add -net 10.8.117.0 netmask 255.255.255.0 gw 10.8.117.2 Tue May 17 23:18:25 2011 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:18:25 2011 Socket Buffers: R=[126976->131072] S=[126976->131072] Tue May 17 23:18:25 2011 UDPv4 link local (bound): [undef] Tue May 17 23:18:25 2011 UDPv4 link remote: [undef] Tue May 17 23:18:25 2011 MULTI: multi_init called, r=256 v=256 Tue May 17 23:18:25 2011 IFCONFIG POOL: base=10.8.117.4 size=62 Tue May 17 23:18:25 2011 IFCONFIG POOL LIST Tue May 17 23:18:25 2011 vpnCh8TestClient,10.8.117.4 Tue May 17 23:18:25 2011 Initialization Sequence Completed Tue May 17 23:27:22 2011 MULTI: multi_create_instance called Tue May 17 23:27:22 2011 192.168.0.104:1194 Re-using SSL/TLS context Tue May 17 23:27:22 2011 192.168.0.104:1194 LZO compression initialized Tue May 17 23:27:22 2011 192.168.0.104:1194 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:27:22 2011 192.168.0.104:1194 Local Options hash (VER=V4): '530fdded' Tue May 17 23:27:22 2011 192.168.0.104:1194 Expected Remote Options hash (VER=V4): '41690919' Tue May 17 23:27:22 2011 192.168.0.104:1194 TLS: Initial packet from [AF_INET]192.168.0.104:1194, sid=8972b565 79323f68 Tue May 17 23:27:22 2011 192.168.0.104:1194 VERIFY OK: depth=1, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:22 2011 192.168.0.104:1194 VERIFY OK: depth=0, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:22 2011 192.168.0.104:1194 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue May 17 23:27:22 2011 192.168.0.104:1194 [vpnCh8TestClient] Peer Connection Initiated with [AF_INET]192.168.0.104:1194 Tue May 17 23:27:22 2011 vpnCh8TestClient/192.168.0.104:1194 MULTI: Learn: 10.8.117.6 -> vpnCh8TestClient/192.168.0.104:1194 Tue May 17 23:27:22 2011 vpnCh8TestClient/192.168.0.104:1194 MULTI: primary virtual IP for vpnCh8TestClient/192.168.0.104:1194: 10.8.117.6 finally, the server status log: OpenVPN CLIENT LIST Updated,Tue May 17 23:36:25 2011 Common Name,Real Address,Bytes Received,Bytes Sent,Connected Since vpnCh8TestClient,192.168.0.104:1194,4244,5604,Tue May 17 23:27:22 2011 ROUTING TABLE Virtual Address,Common Name,Real Address,Last Ref 10.8.117.6,vpnCh8TestClient,192.168.0.104:1194,Tue May 17 23:27:22 2011 GLOBAL STATS Max bcast/mcast queue length,0 END

  Read the article

• Modify registry for Internet Connection Sharing?

  - by Tim

  My OS is Windows XP. Quoted from How to Change the IP Range for the Internet Connection Sharing DHCP service Use Registry Editor to modify the data value of the IntranetInfo value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Settings\General The first number listed is the IP address of the internal IP address of the Connection Sharing host. The second number is the subnet IP address separated by a comma. Enter the first IP address of the new range followed by the subnet mask, separated by a comma. (For example, 169.254.0.1,255.255.0.0.). Modify the data value of the Start value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Addressing\Settings Change the value to the second address of the selected IP range. This address cannot be the same or a lower value than the IP address used for the IntranetInfo key. Modify the data value for the Stop value in the same registry key. Enter the last the IP address of the selected IP range. My registry table does not have Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing, and I don't know how to do with my registry table following the above three steps. Can someone guide me through it step by step?

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >