Search Results

Search found 8976 results on 360 pages for 'advanced customer'.

Page 94/360 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

• Disk is spinning down each minute, unable to disable it

  - by lzap

  I played with spindown and APM settings of my Samsung discs and now they spin down every minute. I want to disable it, but it seems it does not accept any of the spindown time or APM values. Nothing works, it's all the same. Please help what values should be proper for it. I do not want it to spin down at all. /dev/sda: ATA device, with non-removable media Model Number: SAMSUNG HD154UI Serial Number: S1Y6J1KZ206527 Firmware Revision: 1AG01118 Standards: Used: ATA-8-ACS revision 3b Supported: 7 6 5 4 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 2930277168 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 1430799 MBytes device size with M = 1000*1000: 1500301 MBytes (1500 GB) cache/buffer size = unknown Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 udma7 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test Media Card Pass-Through * General Purpose Logging feature set * 64-bit World wide name * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * NCQ priority information DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Long Sector Access (AC1) * SCT LBA Segment Access (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 326min for SECURITY ERASE UNIT. 326min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 50024e900300cca3 NAA : 5 IEEE OUI : 0024e9 Unique ID : 00300cca3 Checksum: correct I have the very same disc which I did not "tuned" and it does not spin. But I do not know where to read the settings from. The hdparm only shows this: Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 Edit: It seems the issue was tuned daemon in RHEL6. It was too aggressive, I turned off disc tuning and it seems they are no longer spinning down.

  Read the article

• How to set up a mini call center?

  - by Ralph

  I'm trying to figure out how to set up a miniature call center for a small business. Like, for 1-4 people to take calls, but hopefully expandable to more. We want to accept nation-wide calls, and then I guess distribute the calls among the available agents. If no one is available, I guess it should either put them in a queue and play some annoying music for them, or forward to call to an agent who has least-recently taken a call who can then quickly answer and say "please hold" until they're done their call. We want to have one phone number that customers can call. I guess we then need some kind of ACD system which would take each call and forward it to an agent based on some algorithm? Then we would need to purchase a separate phone line for each agent, plus one just for the distributor? Or do we need several "extra" lines to maintain a queue (one for each customer waiting too)? This "ACD" thing, is it just a device that you would plug a phone line into (or several?), and maybe connect to a computer, aided by some software? Or is a subscription thing that I would need from my local telephone provider? Next, the business we're running, the callers will be repeat customers. It would be helpful to automatically pull up their profile based on the incoming number. The "software" our agents will be running will just be a website where they can log in (preferably from home) and then enter some information they would obtain through the call. So, the system would have to somehow interface with the website if possible. If not, we'll just have to ask each customer for an identifier (phone number, username, customer number, or something). Is this possible? I guess each computer would need a device that the call would pass through, and then if I can somehow hook into that, then I can write some software that will interface with the site. So, where do I start? What hardware do we need to buy? What subscriptions do we need? We were thinking this magicJack might help us in accepting long-distance calls for cheaper, but my understanding is that they provide you with some weird-looking number, is there a way we could "mask" it with our toll-free number? And then pass the incoming calls through the distributor system, which would then get passed to the call-accepting device which would both allow an agent to answer the call and have a software hook? (I realize this might be partially out of the scope of SU, but I wasn't sure where else to ask. It is about computer(-aided) hardware and software anyway.) P.S.: I don't need any of that "press 1 to talk to..." or "say xyz to..." junk. Just a straight-forward, connect-to-next-available-agent system.

  Read the article

• Set a login with username/password for SQL Server 2008 Express

  - by Ewald Stieger

  I would like to set a password and username for connecting to a server with SQL Management Studio 2008. I set up SQL Server 2008 Express on a customer's computer to host a DB used by an Access 2007 app. The customer should not be able to access the DB or connect with SQL Management Studio. How do I set up a login and remove any logins that allow a user to connect via Windows Authentication and without entering a username and password? I have not much experience with logins and controlling access.

  Read the article

• XAMPP vs WAMP security and other on Windows XP

  - by typoknig

  Not long ago I found WAMP and thought it was a God send because it had all the things I wanted/needed (Apache, PHP, MySQL, and phpMyAdmin) all built into one installer. One thing about WAMP has been making me mad is an error I get in phpMyAdmin about the advanced features not working. I have tried to fix that error long enough on that error for long enough. http://stackoverflow.com/questions/2688385/problem-with-phpmyadmin-advanced-features I now read that most people prefer XAMPP over WAMP, but I am a bit concerned that XAMPP might have some extra security holes with Mercury and Perl, two thing that I don't really need or want right now. Are my security concerns justified or not? Is there any other reasons to go with XAMPP over WAMP or vice versa?

  Read the article

• Outlook receives winmail.txt attachment instead of Excel, PowerPoint or Word attachments from Lotus notes senders

  - by Philippe

  Ok so the title pretty much says it all. We are offering a Hosted Exchange solution for our customer. Everything is working fine except for one customer complaining that he is receiving winmail.dat or winmail.txt attachments instead of the actual Word Excel or PowerPoint attachments he should be receiving, only when these messages come from a specific European senders, that is using Lotus Notes. I know that usually the problem is coming from Outlook senders to other mail clients, but this is not the first they inform me of this but I can't find anything on the matter so far. Has anyone ever gotten and solved this problem? If not, does anyone have any idea regarding this? I had solved this problem a few months ago, by upgrading Outlook to SP2 and then uninstalling it using the Service Pack removing tool of Microsoft. It seems that only the latest SP1 version could work but not the SP2. The problem is that now nothing is working at all. Thank you for your help, Philippe

  Read the article

• XBMC launching external applications full screen

  - by Aquadisco

  Running xbmc-standalone (Eden) on Ubuntu server edition 12.04 (no gnome/kde/etc...). When launching another application via 'advanced launcher' or other launcher add-on XBMC goes into a 'windowed mode' and the app shows up in a 'windowed' mode. The XBMC and app windows are cascaded and most of the screen is unused. This is obviously not what i'd like. I'd like the app to launch full screen. ideas? Other info: - using lightdm - tried with 'Rom Browser' - tried with 'Advanced Launcher' - once app had launched, tried to 'toggle full screen' in app, but with no success

  Read the article

• Best practice for authenticating DMZ against AD in LAN

  - by Sergei

  We have few customer facing servers in DMZ that also have user accounts , all accounts are in shadow password file. I am trying to consolidate user logons and thinking about letting LAN users to authenticate against Active Directory.Services needing authentication are Apache, Proftpd and ssh. After consulting security team I have setup authentication DMZ that has LDAPS proxy that in turn contacts another LDAPS proxy (proxy2) in LAN and this one passes authentication info via LDAP (as LDAP bind) to AD controller.Second LDAP proxy only needed because AD server refuses speak TLS with our secure LDAP implemetation. This works for Apache using appropriate module.At a later stage I may try to move customer accounts from servers to LDAP proxy so they are not scattered around servers. For SSH I joined proxy2 to Windows domain so users can logon using their windows credentials.Then I created ssh keys and copied them to DMZ servers using ssh-copy, to enable passwordless logon once users are authenticated. Is this a good way to implement this kind of SSO?Did I miss any security issues here or maybe there is a better way ofachieving my goal?

  Read the article

• Temporarily Utilizing 304 Header on Apache for Crawlers

  - by Volomike

  I have a client who has a hosting arrangement with 400 customer sites all hosted through SuPHP in CGI mode on Apache. The sysop is now gone and the client is calling on me for rolling out a new PHP thing. Trouble is -- server load is very high right now and we have found that it's due to the crawlers. We had one customer in particular who complained of slow websites, and we engaged a 304 header plugin in his site against most crawlers, and his site perked right up. We'd like to lower that load by issuing a global 304 header to all the crawlers, letting human visitors through. I have a long list of user agent keywords to trap for. What's the best way to temporarily engage that global 304 header, while allowing human visitors to get right on through? I mean, I could roll out 400 .htaccess file changes, but it would be ideal to make this change in like one central Apache config and then it automatically affect all the sites at once.

  Read the article

• Amazon EC2: possible to use elastic load balancing across web servers in multiple regions based on location of client?

  - by Tony

  Related to an another question I asked. This question seems similar but I'm wondering if there are any updates. To support a single site that has users all over the world, I will create EC2 web servers in the US, Asia and Europe regions. The web server instances in the US and Asia regions will be backed by RDS replicas. Is it possible to load balance across these three regions? So when a customer from Spain goes to example.com, she should be routed to the EC2 instances in Europe region, a customer in Miami should be sent to the instance in Eastern US region, etc. Is this possible to do this with just AWS features? Are there docs on how to set this up?

  Read the article

• Outlook folder structure Template

  - by Filip Ekberg

  Having a lot of different customers and a lot of different areas to work with makes it trivial to have your mail folders in order. Everytime I get a new Project / Customer I want to add a certain Folder Structure in my "Customer" / "Project" sub directory. It might look like this: Customer_name/ Bugs Documents Important Support/ Done And as it is today, I have to manually add these manually, which is harsh when you have a lot of it going on and each sub directory under the customer_name directory needs to have "display all items" since it's important to me to see all Items in Bugs / Support / Important. Makes my life easier. So, Is it possible to Automize the process somehow? Macro? Folder Templates? What are my options?

  Read the article

• nsdata to nsstring to nsdata

  - by Jayshree

  Hello everybody. I am calling the webservices. The web service returns data in xml format. Now the problem is the xml data is not being received in proper format. In place of "<", "" it returns in html format like-(<) and (>) . So i assigned the xmldata to a NsMutableString and replaced the escape characters so that the format of xml data is proper. Then i reassigned the NSMutableString to NSData so that i can parse the tags. but the problem is the xmlparser stops right where the xml data is. Where i replaced the tags. it doesnt go further. can anybody make me understand what is going on???? This is the xml response from webservice that i called. <?xml version="1.0" encoding="ISO-8859-1"?><SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"> <SOAP-ENV:Body> <ns1:GetCustomerInfoResponse xmlns:ns1="http://aa.somewebservice.com/phpwebservice"> <return xsi:type="xsd:string"> &lt;?xml version=&quot;1.0&quot; encoding=&quot;utf-8&quot;?&gt;&lt;customer&gt;&lt;id&gt;1&lt;/id&gt;&lt;customername&gt;Hitesh&lt;/customername&gt;&lt;phonenumber&gt;98989898&lt;/phonenumber&gt;&lt;/customer&gt; </return> </ns1:GetCustomerInfoResponse> </SOAP-ENV:Body> </SOAP-ENV:Envelope> And this is after i replaced the tags. <?xml version="1.0" encoding="ISO-8859-1"?><SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"> <SOAP-ENV:Body> <ns1:GetCustomerInfoResponse xmlns:ns1="http://a.somewebservice.com/phpwebservice"> <return xsi:type="xsd:string"> <?xml version="1.0" encoding="utf-8"?> <customer><id>1</id><customername>Hitesh</customername><phonenumber>98989898</phonenumber></customer> </return> </ns1:GetCustomerInfoResponse> </SOAP-ENV:Body></SOAP-ENV:Envelope> Now the problem is while parsing the parser only goes upto return tag. And then it is stuck there. It doesnt go any further. So wat do i do? anybody care to help me?

  Read the article

• How to disable PHP's ini_set for specific configuration options?

  - by Dunedan

  I'm running a setup with PHP 5.3.8 and use php-fpm with it's chroot functionality to separate multiple customers. So each customer has it's own chrooted PHP-environment, which is quite fine. I now want to disallow that a customer can change the *memory_limit* of his PHP-instance by using *ini_set*. On the other hand I don't want to disable *ini_set* completely. So I'm searching for a possibility to disable the possibility to set specific PHP configuration options (like *memory_limit*) via *ini_set*. Does somebody know how to achieve that?

  Read the article

• Additional mailboxes in Outlook 07 SP2

  - by Nick

  I have had my Outlook 2007 open additional mailboxes via the advanced account settings. After updating to Office SP2, the list of emails in the additional account still displays, but I get a message for each mailbox item: This item cannot be displayed in the Reading Pane. Open the item to read its contents. After double clicking the message, I get a small error box which displays just Cannot open this item. Unknown Error. Also, if I try to re-add the mailbox in the Advanced tab of my account settings, I get an error message The name cannot be resolved. The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action. However, the status bar indicates Online with Microsoft Exchange, and I can both send and receive emails from my primary account. What could be going wrong?

  Read the article

• Can I split a spreadsheet into multiple files based on a column in Excel 2007?

  - by geofftnz

  Is there a way in Excel to split a large file into a series of smaller ones, based on the contents of a single column? eg: I have a file of sales data for all sales reps. I need to send them a file to make corrections and send back, but I dont want to send each of them the whole file (because I dont want them changing eachother's data). The file looks something like this: salesdata.xls RepName Customer ContactEmail Adam Cust1 [email protected] Adam Cust2 [email protected] Bob Cust3 [email protected] etc... out of this I need: salesdata_Adam.xls RepName Customer ContactEmail Adam Cust1 [email protected] Adam Cust2 [email protected] and salesdata_Bob.xls Bob Cust3 [email protected] Is there anything built-in to Excel 2007 to do this automatically, or should I break out the VBA?

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• How to enable customers to use their own domain for sites hosted by me [closed]

  - by Scott

  I am thinking of running a self-site builder. But was wondering how would I allow customers to use their own domains that they already own. Is that even possible? Let's say my site is www.bestsitebuildingwebsite.com and each customer has urls like this www.bestsitebuildingwebsite.com/frances www.bestsitebuildingwebsite.com/eden www.bestsitebuildingwebsite.com/john And a customer has a domain called widgets.com Is it actually possible domain widgets.com to go to my site somehow and have HASHES on the URL still work (my site makes use of hashes for AJAX queries). And their site still have good SEO with Google? Thanks Scott

  Read the article

• Remove all HTTP bindings from an IIS 6 site while leaving SSL bindings

  - by MikeBaz

  We have a (remote, via a reseller) customer who configured their IIS6 server to not have any port 80 HTTP bindings, only port 443 SSL bindings. We would like to reproduce this without going through the three layers (!) to get to the customer to test some error scenerios. However, whenever I try to get IIS to not listen on IIS at all, I can't do it. If I do it in the UI, either leaving in the main properties page, or in the advanced bindings page, the UI does not let me proceed. If I remove the HTTP ServerBindings from the metabase.xml directly, IIS makes it port 80, all unassigned addresses anyway. Is there a way to get to the "SSL only" state naturally? Please note I am NOT talking about the "require SSL" checkbox or underlying metabase setting, as that still listens on port 80 (or whatever) to give the "SSL required" error message. I'm talking about not having any bindings listed at all for HTTP.

  Read the article

• Many users send using a single address, replies to that single address go to many users

  - by Keyslinger

  I work in an office with a Microsoft Exchange server for email. I would like to have the following workflow: John, Mary, or Sam send a message from Outlook on their respective computers. The customer receives the message from the address "[email protected]" The customer replies to the message from [email protected] and it is received by John, Mary, or Sam depending on who sent the message (if it was sent by John, the reply is sent to John, and so on). All users should also be able to send emails from their respective addresses as well (e.g. [email protected], etc.) Is this possible? If so, how can it be accomplished?

  Read the article

• Many users send using a single address, replies to that single address go to many users

  - by Keyslinger

  I work in an office with a Microsoft Exchange server for email. I would like to have the following workflow: John, Mary, or Sam send a message from Outlook on their respective computers. The customer receives the message from the address "[email protected]" The customer replies to the message from [email protected] and it is received by John, Mary, or Sam depending on who sent the message (if it was sent by John, the reply is sent to John, and so on). All users should also be able to send emails from their respective addresses as well (e.g. [email protected], etc.) Is this possible? If so, how can it be accomplished?

  Read the article

• Amusing or Sad? Network Solutions

  - by dbasnett

  When I got sick my email ended up in every drug sellers email list. Some days I get over 200 emails selling everything from Viagra to Xanax. Either they don't know what my condition is or they are telling me you are a goner, might as well chill-ax and have a good time. In order to cut down on the mail being downloaded I thought I would add all of the Junk email senders from Outlook to my Network Solution mail server. Much to my amazement I could not find that import Spammers button, so I submitted a tech support request. Here is the response: Thank you for contacting Network Solutions Customer Service Department. We are committed to creating the best Customer experience possible. One of the first ways we can demonstrate our commitment to this goal is to quickly and efficiently handle your recent request. We apologize for any inconvenience this might have caused you. With regard to your concern, please be advised that we cannot import blocked senders in to you e-mail servers. An alternative option is for you to create a Custom Filter that filters unwanted e-mails. To create a Custom Filter: Open a Web browser (e.g., Netscape, Microsoft Internet Explorer, etc.). Type mail.[domain name].[ext] in the address line. Login to your Network Solutions email account. Click on the Configuration left menu tab. Click on the Custom Filter link. Type the rule name. blah, blah, blah Basically add them one at a time. "We are committed to creating the best Customer experience possible." No you are not. You are trying to squeeze every nickle you can out of me. "With regard to your concern, please be advised that we cannot import blocked senders in to you e-mail servers." Maybe I should apply for a job to write those ten complicated lines of code... Maybe I should question my choice of vendors, because if they truly "cannot" then they are to stupid to have my business. It is both amusing and sad. I'll be posting this in every forum I am a member of.

  Read the article

• Java works under Firefox but crashes Internet Explorer

  - by Dominic Grenier

  Java works under Firefox and Chrome but not under IE. Here's what I tried (the advice normally given on forums): Java applet activated in tools - internet options - security tab - personnalise - Java applets Activated in tools - manage add-ons - tool bars and extensions - Java (tm) SSV2 helper - Activate Activated in tools - internet options - advanced tab - Use JRE for applet I've also deleted my temporary internet files (with Ccleaner), Reinstalled IE8 It is also set as the default Java for IE through the control panel - Java - Advanced tab - default Java for browsers - Microsoft Internet Explorer IE version: 8.0.6001.18702 Java version: 1.7.0_03. (also tried with 1.6.0_31) Windows XP SP3. Any advice? Thanks :) edit: I have activated the ActiveX controls through manage add-ons - all add-ons but now, although the coffe cup loading screen appears (which did not before) it makes IE crash (which is new). I might have fiddled too much with the registry by trying to completely remove Java to reinstall it, so I ran "rereg" (a tool to repair dlls and their registry entries) without success.

  Read the article

• Must I have Exchange to use Blackberry Enterprise Server Express?

  - by John Spaz

  In the past I've setup BES (not express) for a company that just wanted their users on the corporate network, they didn't care for email or any other enterprise feature, they just wanted to push a policy that the phones internet should be routed through the corporate network. I want to setup BES Express now for a customer that also just wants the phones on his network but wherever I look, it says that BES Express requires Exchange. Is there a way to install BES Express without Exchange and without a AD Domain? Basically what the customer wants to accomplish is to be able to filter and log the internet access on the phones.

  Read the article

• Postfix: How to apply header_checks only for specific Domains?

  - by Lukas

  Basically what I want to do is rewriting the From: Header, using header_checks, but only if the mail goes to a certain domain. The problem with header_check is, that I can't check for a combination of To: and From: Headers. Now I was wondering if it was possible to use the header_checks in combination with smtpd_restriction_classes or something similar. I've found a lot information about header_checks and multiple header fields, when searching the net. All of them basically telling me, that one can't combine two header for checking. But I didn't find any information if it was possible to only do a header check if a condition (eg. mail goes to example.com) was met. Edit: While doing some more Research I've found the following article which suggests to add a Service in postfix master.cf, use a transportmap to pass mails for the Domain to that service and have a separate header_check defined with -o. The thing is that I can't get it to work... What I did so far is adding the Service to the master.cf: example unix - - n - - smtpd -o header_checks=regexp:/etc/postfix/check_headers_example Adding the followin Line to the transportmap: example.com example: Last but not least I have two regexp-files for header checks, one for the newly added service, and one to redirect answers to the rewritten domain. check_headers_example: /From:(.*)@mydomain.ain>(.*)/ REPLACE From:[email protected]>$2 Obviously if someone answers, the mail would go to nirvana, so I have the following check_headers defined in the main postfix process: /To:(.*)<(.*)@mydomain.example.com>(.*)/ REDIRECT [email protected]$2 Somehow the Transport is ignored. Any help is appreciated. Edit 2: I'm still stuck... I did try the following: smtpd_restriction_classes = header_rewrite header_rewrite = regexp:/etc/postfix/rewrite_headers_domain smtpd_recipient_restrictions = (some checks) check_recipient_access hash:/etc/postfix/rewrite_table, (more checks) In the rewrite_table the following entries exist: /From:(.*)@mydomain.ain>(.*)/ REPLACE From:[email protected]>$2 All it gets me is a NOQUEUE: reject: 451 4.3.5 Server configuration error. I couldn't find any resources on how you would do that but some people saying it wasn't possible. Edit 3: The reason I asked this question was, that we have a customer (lets say customer.com) who uses some aliases that will forward mail to a domain, let's say example.com. The mailserver at example.com does not accept any mail from an external server that come from a sender @example.com. So all mails that are written from example.com to [email protected] will be rejected in the end. An exception on example.com's mailserver is not possible. We didn't really solve this problem, but will try to work around it by using lists (mailman) instead of aliases. This is not really nice though, nor a real solution. I'd appreciate all suggestions how this could be done in a proper way.

  Read the article

• How to find what Service Pack of IE is currently installed on the system?

  - by Kanini

  Hello...We have website and one of our customers complains that when he launches the URL there is a blank popup that appears on his window. He uses IE 7. We have tried to reproduce the same behaviour in our local PC's but we are not able to do so. The site opens up perfectly fine in our systems. We suspect that it could be due to a different Service Pack installed on the customer's PC. Is there a way we can find out which SP is he running on. What would be the simplest process which we can then pass on to the customer to know which SP is he running on?

  Read the article

• Outlook receives winmail.txt attachment instead of Excel, PowerPoint or Word attachments from Lotus

  - by Philippe

  Ok so the title pretty much says it all. We are offering a Hosted Exchange solution for our customer. Everything is working fine except for one customer complaining that he is receiving winmail.dat or winmail.txt attachments instead of the actual Word Excel or PowerPoint attachments he should be receiving, only when these messages come from a specific European senders, that is using Lotus Notes. I know that usually the problem is coming from Outlook senders to other mail clients, but this is not the first they inform me of this but I can't find anything on the matter so far. Has anyone ever gotten and solved this problem? If not, does anyone have any idea regarding this? I had solved this problem a few months ago, by upgrading Outlook to SP2 and then uninstalling it using the Service Pack removing tool of Microsoft. It seems that only the latest SP1 version could work but not the SP2. The problem is that now nothing is working at all. Thank you for your help, Philippe

  Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >