Search Results

Search found 35538 results on 1422 pages for 'access 2007'.

Page 952/1422 | < Previous Page | 948 949 950 951 952 953 954 955 956 957 958 959  | Next Page >

• Losing WLAN connections but maintaining internet connections on WIndows 7 Workgroup

  - by Di

  I have 4 computers all running Windows 7 networked in a Work group through Billion 7404vgp-m wireless router. All drivers and firmware for wireless adapters and router are up to date. Windows Firewall and Defender disabled. Disconnected ipv6. Running Nod 32 anti virus software. All have own static IP address 192.XXX.X.XXX. When I Reset the router all computers have Internet and LAN access for about 1 hour and then they will lose the LAN connection but maintain Internet connection. Resetting wireless adapters or restarting computers does nothing to fix this but resetting router will. What is causing this? How do I fix it?

  Read the article

• How to stream multiple files on demand in VLC?

  - by romkyns

  Is there any way at all that I can set up VLC on a server PC in such a way that I can access a list of all my videos from another PC, and pick one to be streamed on demand? I've been pointed at this streaming guide (pdf), but it's pretty useless. For a start, most of the menus in those screenshots don't match the actual current version VLC, and then it sort of assumes you already know what you're doing. So far I managed to figure out how to stream a single file, which I must choose before watching on the server PC - pretty useless if you ask me! The impenetrable "UI" doesn't help either... (P.S. The reason I'm going for streaming rather than the very simple to set up network drive is described in this question)

  Read the article

• Prioritize file sharing performance in Windows Server 2008

  - by cmbrnt

  I've got a server running Windows Server 2008, and use it mainly for sharing files throughout the domain from a number of disks. It's running on VMware ESXi 4.0, in case that matters. My problem is that when I log in to the server to check user permissions etc, the access speed the files on the remote disks almost grinds to a halt. I havn't been able to measure the speeds, but I would guess it slows down to about 100kB/s as soon as I log in. This is on a gigabit network and the problems are equal for all users, even the ones connected to the same switch as the server. I've assigned 2 GB RAM to the server, and reserved it 1,5Ghz processor power. I don't have to do anything special on the server for this halt to occur. How can I make sure file sharing is prioritized on the server, so no matter what applications I'm using it will always make sure file sharing works properly? Could this be a VMware issue?

  Read the article

• time on files differ by 1 sec. FAIL Robocopy sync

  - by csmba

  I am trying to use Robocopy to sync (/IMG) a folder on my PC and a shared network drive. The problem is that the file attributes differ by 1 sec on both locations (creation,modified and access). So every time I run robocopy, it syncs the file again... BTW, problem is the same if I delete the target file and robocopy it from new... still, new file has 1 sec different properties. Env Details: Source: Win 7 64 bit Target: WD My Book World Edition NAS 1TB which takes its time from online NTP pool.ntp.org (I don't know if file system is FAT or not)

  Read the article

• Authenticated proxy in Windows command prompt

  - by tlvince

  My Internet access is delivered through an authenticated proxy. This is setup correctly in the "Internet Options" control panel applet and all browsing/GUI apps work fine. For cmd, proxy settings are typically set by exporting http_proxy. The applications I'm trying to use are git and Putty's pscp.exe. I've tried the following syntax to no avail: set http_proxy=http://username:[email protected]:port/ I've also experimented with Netsh.exe and ProxyCfg.exe with no luck. How does one configure an authenticated proxy in the Windows command prompt?

  Read the article

• SharePoint doesn't support this authentication scheme.

  - by EtherDragon

  I have a new Windows Phone 7 phone, and I'm trying to investigate how to connect the Office application to our SharePoint site(s). In the Office application, on Phone 7, I flip to the SharePoint page. I go to open URL, and enter the url for one of my sites, that uses default authentication (Windows Auth). I get a message: Can't open SharePoint doesn't support this authentication scheme. For assistance, contact the person who manages thus SharePoint site (That would be me). You can try opening the content in your web browser instead. When opening in my browser, I can access the content without any problem. (Windows Auth passes) Anyone have any source material on what I should do to my SharePoint site to "support this authentication scheme?" Note: I am the administrator of our SharePoint server farm(s).

  Read the article

• When connected to VPN through Windows 7 running under OS X via VMWare Fusion, does traffic from the OS X side go through the VPN?

  - by user1202747

  I only have a rudimentary knowledge of VPNs. My understanding is that, in most network configurations, when a client is connected remotely to a VPN server, all network traffic passes through the VPN server before going to the client, and all data coming from the client passes through the VPN server before going out over the wider Internet. I run Windows 7 using VMWare Fusion under OS X Lion. If I access a web page in Safari, say, on the OS X side of things, does that traffic pass through the VPN server? Or does it bypass it because the two OS's are regarded as separate network devices by my LAN? I would appreciate any insight anyone can provide. Thanks.

  Read the article

• Can a mapped network drive be reconnected from the command line?

  - by Stephen Jennings

  On a daily basis I find myself in the Windows command prompt needing to access a network drive that is mapped but disconnected. I have yet to find a command that will reconnect this drive without unmapping and remapping (which leads to a password guessing game, since I don't own these computers). I would also like to be able to script this so every night the drive is reconnected if it has become disconnected somehow. The fastest solution I currently have is to: Type "start." to open explorer, Alt-D to focus the address bar, type the drive letter I want and press enter, and wait for it to display the drive contents, then finally, close explorer and go back to the command prompt. I know it's a minor inconvenience, but I'm often doing this through a slow VNC or PCAnywhere connection where doing anything through GUI is awful, so I'm just wondering if there's a better solution.

  Read the article

• Selectively routing traffic via ethernet or wifi, with proper DNS (Mac OS X 10.6)

  - by Dan

  When I'm at work, I access various intranet pages as well as the wider Internet through ethernet. However, the company LAN blocks some ports (e.g. Google Calendar). I can get to those through WiFi. So, I gave the Airport priority, and then using route add, I set up selective routing: all intranet traffic goes through the ethernet and everything else via WiFi: sudo route add 10.0.0.0/8 <intranet gateway>. However, there are a number of intranet sites that have their own DNS; i.e., hr.company.com only resolves on the intranet. The only way that I can get the DNS to work properly is to add the internal DNS server to the Airport DNS listing, however I fear that when I go elsewhere and forget, this will break things. What's the right way to get the DNS to resolve using this setup?

  Read the article

• Gmail/Facebook/Hotmail not opening in Firefox/IE on Windows 7 Home

  - by singlepoint

  Hi, I am unable to open Gmail/Facebook/Hotmail on Firefox/IE on Widows 7 Home. I just unboxed a brand new hp laptop with Norton Security Suite running inside. I get following error message on Firefox. Please help. The connection has timed out The server at www.google.com is taking too long to respond. * The site could be temporarily unavailable or too busy. Try again in a few moments. * If you are unable to load any pages, check your computer's network connection. * If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web

  Read the article

• Someone try to hack my site, want to understand the log

  - by garconcn

  I have a wordpress site hosted on CentOS 6. After see the following access log, I checked the server, it seems ok. Can anyone explain what does this guy trying to do? Did they get what they want? I have disabled allow_url_include, and restricted open_basedir to web dir and tmp(/etc is not in the path). 190.26.208.130 - - [05/Sep/2012:21:24:42 -0700] "POST http://my_ip/?-d%20allow_url_include%3DOn+-d%20auto_prepend_file%3D../../../../../../../../../../../../etc/passwd%00%20-n/?-d%20allow_url_include%3DOn+-d%20auto_prepend_file%3D../../../../../../../../../../../../etc/passwd%00%20-n HTTP/1.1" 200 32656 "-" "Mozilla/5.0"

  Read the article

• My Domain Is Getting Blocked As Gambling

  - by Tim Scott

  I have a site at http://slotted.co. Some of my would-be users complain that their company firewall blocking access. At least one user told me it was flagged as a gambling domain, which it is not. What can I do about this? Incidentally I own some other domains, such as signupster.com, which redirect to my site. I wonder if a quick workaround would be to make that my main domain and have slotted.co redirect? Obviously I prefer in the long terms that slotted.co is considered clean.

  Read the article

• How can one domain route to an always-changing pool of servers?

  - by ryeguy

  I'm sure this is an easy solution, I'm just not too familiar with how DNS works or if that's even related to this problem. If I'm running a web service on amazon ec2, distributed across many instances, how can I make it so a single domain name can be used to access the entire pool of servers, which will be changing from time to time? Since the instances may be present one second but gone the next (and vice versa), I need a way to randomly pick an active member of the cluster to route to. The updates would have to be instantaneous. Is this even possible, with dns caching and all?

  Read the article

• Need help to figure out iptables rule

  - by Master

  I have this iptable rule listing Chain INPUT (policy DROP) target prot opt source destination ACCEPT tcp -- 127.0.0.1 0.0.0.0/0 tcp dpt:3306 acctboth all -- 0.0.0.0/0 0.0.0.0/0 VZ_INPUT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:3306 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:3306 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:3306 ACCEPT tcp -- 94.101.25.40 0.0.0.0/0 state NEW tcp dpt:3306 Chain FORWARD (policy DROP) target prot opt source destination VZ_FORWARD all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy DROP) target prot opt source destination acctboth all -- 0.0.0.0/0 0.0.0.0/0 VZ_OUTPUT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT tcp -- 94.101.25.40 0.0.0.0/0 state NEW tcp dpt:3306 I want only localhost and my ip to access tcp 3306. Can i deleted all other rules as shown above. I don't know if i nned to keep any of them or not

  Read the article

• X11 forwarding from one server to other

  - by n3oblit7

  I have a setup where I need to forward X11 from my local machine (laptop) to a Virtual machine. The server hosting this VM cannot be reached directly from my laptop. I need to first login to a gateway and from this gateway, I can access the VM. How can I forward X11 from my laptop to this VM? I have tried following but these do not work: [laptop # ] ssh -X [gateway] [gateway # ] ssh -X [VM] [laptop # ] ssh -tX [gateway] ssh -X [VM] I could forward X11 only till the gateway. (DISPLAY variable gets set on gateway)

  Read the article

• Sudden complaint that Windows is not genuine - some questions

  - by blade

  Hi, I used to use VMWare Workstation and made several VMs with Win Server 2008, which worked fine. My first tasks were to setup RDP, updates, and activate the OS. I deleted Workstation and thus did not have my VMs available to use for about 2 months. Now I have VMWare Server 2.0.2 as I this is free and I am going to get Hyper-V on a host Win Server in about March, but when I have accessed one of my VMs (haven't tried the others yet), it complains that the copy of Windows is not genuine. I now have a black screen but can access all my apps on the VM. Will the OS eventually shut me out from accessing it? I got my key from the Action Pack but the standard R2 key has been taken down and replaced with the Enteprise R2 key. I have Enterprise R2 but apparently the autorun is corrupt! Thanks

  Read the article

• Win Server 2008 R2 - Mapped shared folder hanging?

  - by M-Tech

  I have recently built a windows 2008 server R2 machine. This is purely for file server purposes and is very much a basic build. All windows updates installed and part of domain. I have setup a shared folder on the C:Drive and added permissions for domain users as co-owners. The client machines run XP SP3 and are part of the domain also. We have a few servers running the same setups on a few of our sites but this one is particular crashes users machines (explorer.exe hangs for at least a few mins) when attempting to access the shared folder. I have turned off the option on the network card for power save aswell still no change. Any help with this is very much appreciated and i look forward to hearing from you ;)

  Read the article

• Mysql Encryption and Key managment

  - by microchasm

  I am developing a local intranet system in PHP/MySQL to manage our client data. It seems that the best practice would be to encrypt the sensitive data on the MYSQL server as it is being entered. I am not clear, though, on what would be the best way to do this while still having the data readily accessible. It seems like a tough question to answer: where is the key(s) stored? How to best protect the key? If the key is stored on each users' machine, how to protect it if the machine is exploited? If the key is exploited, how to change the key? If the key is to be stored in the db, how to protect it there? How would users access it? If anyone could point me in the right direction, or give some tips I'd be very grateful. Thanks.

  Read the article

• Where might I be having problems with making web server acessable (XAMPP)

  - by Erx

  I've installed XAMPP and it seems to be working - sort of. It will serve pages if I access it via http://localhost or 127.0.0.1 but not if I use the actual IP address I have. I thought it might be a firewall issue, so I turned off the firewall and the issue still remains. I don't have enough experience to know where to look next, so I thought I might get some advice here. Running on Vista. The error I'm actually getting it "Timed Out". I've had XAMPP running on this machine prior, but I've had to reinstall my OS/new hard drive ... and I can't seem to get it working.

  Read the article

• Network configuration with limited hardware

  - by Pavel

  I have cable internet and I have two PC. One of them has wireless and ethernet, the other pc has ethernet only. Also, I have a dsl modem that has wireless builtin (some common speedstream model). My goal is to connect all of them so that both have internet access. As I understand, I have two options: connect speedstream to the cable and then connect other PC's to speedstream; OR, connect pc with wireless to the cable and then connect the other pc that has ethernet only using ethernet+wireless through speestream. First one seems to be easy, but it doesn't seem to work. What about the other choice? Is it possible to do it?

  Read the article

• How to make a secure MongoDB server?

  - by Earlz

  Hello, I'm wanting my website to use MongoDB as it's datastore. I've used MongoDB in my development environment with no worries, but I'm worried about security with a public server. My server is a VPS running Arch Linux. The web application will also be running on it, so it only needs to accept connections from localhost. And no other users(by ssh or otherwise) will have direct access to my server. What should I do to secure my instance of MongoDB?

  Read the article

• ubuntu server refusing connections via port forwarding

  - by Matt

  Getting some really weird behavior from our Ubuntu server... it's behind a Verizon router firewall with port forwarding (port 8080 to port 80 on the server), and we've been having issues accessing it via this external IP. From within the network, it appears to respond normally (I can access it via web browser and SSH), but refuses connections through port forwarding (using our static external IP). The strangest thing is that it actually responds to external port-forwarded connections right after being restarted, but quickly lapses back into this pattern of refusing external connections. I'm a bit of a server newbie (I'm actually a programmer in a small startup that just lost their server ops guy, urgh) so this is all trial by fire for me. Does anyone have any advice on what could be going wrong here? Any help would be appreciated, thanks.

  Read the article

• Change base language of Windows 8 Installer

  - by Firedragon

  I have access to Dreamspark and Windows 8. When I picked the version I picked English which is fine, but it is US English however I realised I should have picked UK English instead. You are only allowed one version so i cannot switch it. Now, I can change the language pack later to UK English but in the language bar US English is always listed and seems impossible to remove and system restore reverts to US English. Is there a way to fully change the base language to UK in the installer, so in effect makin the installer offer US and UK English, or just UK English as if I had chosen the correct version?

  Read the article

• cant recognize the path of hard drive which is not a part of an array

  - by Abhishek

  hi there, I have a problem on my server as below.. On my server i configured a raid array of 3 hard disks, in my c drive their is a web applications running on Apache Tomcat server. Now because of shortage of storage i entered a new hard disk to the server which is not a part of that raid array. Now through my web application i upload some images to new hard drive and file uploaded successfully but when through that same application, i try to retrieve those images and show on a web site i does not recognize that and dose not give any error. i try to access that drive with absolute path but it not works. Can any one help me to find the solution of this problem? Thank You in advance.

  Read the article

• Securing internal data accessed by a website on the big, bad internet

  - by aehiilrs

  A close relative of this question on Stack Overflow: When you have a web site in your DMZ that needs to access production data stored on an internal DB, what strategies do you recommend using to lower the risks that come from accessing live data? Is it even considered acceptable to have a connection initiated from the DMZ come inside of your network? An extra detail about the nature of the site that kind of throws a monkey wrench into the machinery is that people using the web site will be competing for "spots" on a first-come, first-serve basis with others using the internal software. Because of this, as close to zero lag time between the two applications as possible is ideal.

  Read the article

< Previous Page | 948 949 950 951 952 953 954 955 956 957 958 959  | Next Page >