Search Results

Search found 3638 results on 146 pages for 'major'.

Page 98/146 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

• filesystem compatible with freenas and windows

  - by Daniel

  Hi all, I'm planning on using FreeNAS (was considering openfiler but freenas seems simpler) for my home NAS box running off ESXI. I have managed to get local sata drives to mount in ESXI (http://serverfault.com/questions/216902/esxi-add-datastore-without-partitioning). I've had one of the drives fail on my before and I was able to retrieve most of the data off it using windows tools (I'm not much of a linux guy I know enough to be dangerous!). If I go the freenas route in the event that something goes bad what would be the best file system to use so that I could pop the drive out of the freenas box (vm) and put it in another pc running windows so I could try and run various recovery tools to get the data back. All in all its not a major problem if I lose the data just would be a bit annoying, so I'm not looking for suggestions around backing up etc. I was considering using NTFS that the drives are already formatted as but it appears that while freenas does support NTFS that its a bit buggy and not 100% reliable, anyone know if this is still true? Read that on a forum somewhere.

  Read the article

• Xmodmap fails to remap modifier keys

  - by ZyX

  When I try to move keys, so that I have CapsLock on escape, Control on CapsLock and Escape on left control, I get the following error: % xmodmap ~/.Xmodmap X Error of failed request: BadValue (integer parameter out of range for operation) Major opcode of failed request: 118 (X_SetModifierMapping) Value in failed request: 0x17 Serial number of failed request: 15 Current serial number in output stream: 15 That is the code that fails: remove Lock = Caps_Lock ! ESC keycode 9 = Caps_Lock add Lock = Caps_Lock remove Control = Control_L ! CapsLock keycode 66 = Control_L add control = Control_L ! Control_R keycode 37 = Escape ! 2*Meta_L keycode 148 = Meta_L add mod1 = Meta_L If I comment out all lines that start with either add or remove it runs without any errors, but does not do what I want. Program versions (Gentoo x86 (stable)): xorg-server-1.7.6 xmodmap-1.0.4 xf86-input-evdev-2.3.2 Xorg.conf: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 1.0 (buildmeister@builder63) Fri Aug 14 17:54:58 PDT 2009 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Evdev Keyboard" "CoreKeyboard" InputDevice "Evdev Mouse" "CorePointer" EndSection Section "Module" Disable "dri" Disable "dri2" Disable "record" EndSection Section "InputDevice" Identifier "Evdev Keyboard" Driver "evdev" Option "Device" "/dev/input/event2" Option "CoreKeyboard" Option "AutoRepeat" "500 25" Option "XkbRules" "xorg" Option "xkb_rules" "xorg" Option "XkbModel" "yahoo" Option "xkb_model" "yahoo" Option "XkbLayout" "dvp2" # ,ru2 Option "xkb_layout" "dvp2" # ,ru2 # Option "XkbVariant" "" # ,winkeys Option "XkbOption" "grp_led:scroll,grp:rctrl_toggle,compose:rwin,grp:lwin_switch" # grp:lwin_switch EndSection Section "InputDevice" Identifier "Evdev Mouse" Driver "evdev" Option "CorePointer" Option "Device" "/dev/input/event3" Option "Name" "Genius Ergo Mouse" Option "HWHEELRelativeAxisButtons" "7 6" Option "WHEELRelativeAxizButtons" "4 5" Option "SendCoreEvents" "true" Option "Buttons" "11" EndSection Section "Files" FontPath "/usr/share/fonts/misc" FontPath "/usr/share/fonts/Type1" FontPath "/usr/share/fonts/100dpi" FontPath "/usr/share/fonts/75dpi" FontPath "/usr/share/fonts/terminus" # FontPath "/usr/share/fonts/intlfonts" FontPath "/usr/share/fonts/ttf-bitstream-vera" # FontPath "/usr/share/fonts/ttf" FontPath "/usr/share/fonts/corefonts" FontPath "/usr/share/fonts/paratype" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection Section "ServerFlags" # Option "XkbDisable" "false" # Option "AutoAddDevices" "false" Option "DontVTSwitch" "false" Option "DontZap" "false" # Option "DontZoom" "true" EndSection Everything worked before update.

  Read the article

• 8007064c(2011) and 80280007(2009) persistant after all known repairs

  - by tiu44

  I'm on Windows 7 Home x64, and have ran into a major issue with Live Messenger(which I use daily). I have full offline installers for both 2011 and the last Wave 3 2009(14.0.8117.0416) Suites. Both give the following errors: Live Essentials 2011 Offline installer(official): An unknown error occured. Error:0x8007064c Source WLXSuite WL 2009 offline installer(official): You already have a more recent version of Windows Live. Error: OnCatalogResult:0x80280007 Next steps: If you want to install this older version, first uninstall any later versions that are on your computer. Get help with this error The 2011 installer also says it is updating messenger, I don't select anything else. Then last 2009 installer says their is a newer version that needs uninstalled even after the following procedures. MS Help pages provided all basically lead to using uninstall from control panel. Which I've uninstalled all Live components including watcom safety scanner and portable SQL from. I've followed online instructions for manually deleting folders from Program Files(x86), Appdata, and some others under \User\All Users and the one for the one account on the machine. I've used CCcleaner 3.01, ASC 3.7.3 and Beta 4 with deep scan along with deleting folders, and checked their uninstallers for Live components too, and none were there. wlmuninstaller.exe tool reports nothing, but after a failed install it finds something, but failes to clean it under all user admin privilege. The same errors still occur after all of that. Google searching I see people on forums suggesting reinstalling the OS cause MS doesn't even know how to fix this, but I'm hoping someone here can help. NOTE: I don't have System Restore or any other state freeze utilities going, and I don't have any real time AV going(I sometime scan with defender, anti rootkits, and online scanners). NOTE2:I posted this on windowslivehelp.com, before looking to see if the place was active or not, hoping I can get help here. Thanks

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated.

  Read the article

• Degraded RAID-5 array with lvm2 lost superblock and partition table

  - by Fred Phillips

  I have a RAID-5 array of 4x1TB hard disks with one lvm2 partition on Ubuntu Linux 10.04 LTS. One of the disks has failed. I have re-assembled the array without this failed disk but now mdadm --examine claims the array has no superblock and fdisk says it has no partition table. What can I do to recover the data? # mdadm -D /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sat Mar 5 14:43:49 2011 Raid Level : raid5 Array Size : 2930276352 (2794.53 GiB 3000.60 GB) Used Dev Size : 976758784 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Sat Mar 5 15:06:49 2011 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 1 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Name : boba:1 (local to host boba) UUID : 52eb4bc9:c3d8aab5:e0699505:e0e1aa05 Events : 18 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 65 1 active sync /dev/sde1 2 8 49 2 active sync /dev/sdd1 3 0 0 3 removed 4 8 17 - faulty spare /dev/sdb1 # mdadm --examine /dev/md0 mdadm: No md superblock detected on /dev/md0. # fdisk -l /dev/md0 Disk /dev/md0: 3000.6 GB, 3000602984448 bytes 2 heads, 4 sectors/track, 732569088 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1572864 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10] md0 : active raid5 sdb1[4](F) sda1[0] sdd1[2] sde1[1] 2930276352 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [UUU_] unused devices: <none>

  Read the article

• Speakers silent, headphones work in Ubuntu 9.04

  - by CarlF

  I'm running Ubuntu 9.04. Worked fine for months, then I rebooted yesterday after weeks of continuous operation. Now audio won't play through the speakers. The USB headset works fine, but the Conexant audio (CX20549) does not. Weirdly, it thinks it's playing. pavumeter shows appropriate levels, volume looks OK in alsamixer, but no sound. I did find this page: http://www.eugeneteplitsky.com/fixing-silent-pulseaudio-in-ubuntu-9-04/ Unfortunately the advice there doesn't help me. For one thing, the syntax for the alsa-base.conf file is apparently not actually documented anywhere. For another, my chipset isn't listed in the kernel.org docs he links to! EDIT: would upgrading to 9.10 help? Is there a major change in the audio subsystem between 9.04 and 9.10? Any suggestions? EDIT 2: This is stranger than I thought. Sound works normally in Xine, but is silent in Audacity, VLC and mplayer. What the?

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update

  - by tags2k

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update

  - by tags2k

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• I can play "test" sounds, but no other audio works

  - by Callum

  I'm running Windows XP, and last night my PC was infected by a frustrating virus (one of those viruses that won't let you open virus checkers, etc). I finally killed it 2 hours later, but it involved some heavy duty anti-dote. One side effect is my audio is now gone. Except it's not entirely gone, because when I open the Realtek HD Audio Manager in the task bar, I can play all the "test" sounds. The speakers, the sound card, etc, are therefore working fine. But things like YouTube or Windows Media Player, there's no sound. I'm guessing there's a setting that needs to be reconfigured somewhere.. but where? Maybe relevant: One thing I did do last night was "play" with the system registry. Any help would be greatly appreciated. Thanks. SOLVED! The two hour battle with my computer virus resulted in my computer permanently thinking it was in Safe Mode, regardless of how it booted up. I was able to "fix" this by following the post by hsandler in this thread: http://www.petri.co.il/forums/showthread.php?t=23032&page=2 I then rebooted.. and let me tell you, the Windows Startup music has never sounded so sweet. Thanks to all, especially James, whose advice gave me a major clue as to what the problem was.

  Read the article

• How to troubleshoot when one has no idea where to start?

  - by Chris Walton

  I am looking for hints, tips and answers on how to get started on troubleshooting when: The problem is intermittent The problem could lie literally anywhere - operating system; free source software; my own software developments; purchased software; crumbs on the keyboard; the specific combination of software I am currently running; Maxwell's demon; the little blue men actually running the machine have gone on strike; etc. I have expertise only in a few of the areas that are potential candidates for the cause of the problem. The specific problem I am having is detailed below as an example, but I am not seeking answers to my current problem, but rather where and how to start on tackling such problems. I am currently encountering a problem with my new machine. On a few occasions the machine has just frozen; not accepting keystrokes, mouseclicks, or anything except the power on/off switch. Invariably I have been merely browsing the web; I have had a few (<= 6 other applications) running. None of these applications are major; and represent a mix of commercial programs and open source programs, typically migrated from Unix of some variety. My machine is a Windows 7 I7 quad core laptop.

  Read the article

• Looking for a recommendation on measuring a high availability app that is using a CDN.

  - by T Reddy

  I work for a Fortune 500 company that struggles with accurately measuring performance and availability for high availability applications (i.e., apps that are up 99.5% with 5 seconds page to page navigation). We factor in both scheduled and unscheduled downtime to determine this availability number. However, we recently added a CDN into the mix, which kind of complicates our metrics a bit. The CDN now handles about 75% of our traffic, while sending the remainder to our own servers. We attempt to measure what we call a "true user experience" (i.e., our testing scripts emulate a typical user clicking through the application.) These monitoring scripts sit outside of our network, which means we're hitting the CDN about 75% of the time. Management has decided that we take the worst case scenario to measure availability. So if our origin servers are having problems, but yet the CDN is serving content just fine, we still take a hit on availability. The same is true the other way around. My thought is that as long as the "user experience" is successful, we should not unnecessarily punish ourselves. After all, a CDN is there to improve performance and availability! I'm just wondering if anyone has any knowledge of how other Fortune 500 companies calculate their availability numbers? I look at apple.com, for instance, of a storefront that uses a CDN that never seems to be down (unless there is about to be a major product announcement.) It would be great to have some hard, factual data because I don't believe that we need to unnecessarily hurt ourselves on these metrics. We are making business decisions based on these numbers. I can say, however, given that these metrics are visible to management, issues get addressed and resolved pretty fast (read: we cut through the red-tape pretty quick.) Unfortunately, as a developer, I don't want management to think that the application is up or down because some external factor (i.e., CDN) is influencing the numbers. Thoughts? (I mistakenly posted this question on StackOverflow, sorry in advance for the cross-post)

  Read the article

• need advice on data center move, communication with both facilities during transition

  - by Brian Roden

  We are beginning the process of moving to a new facility. Office and warehouse operations will both be moving, and we must get shipping operations up and running at the new location while continuing to ship from the old location. Our contract with some third-party warehouse tenants requires two business day turnaround (only weekends and holidays excluded), so we can't have major downtime during the move. We would like to keep our 172.16.60/61.xxx internal address space in use throughout the move. Is it possible to keep using this same internal range, and have our existing WatchGuard Firebox 520 and whatever router we get for the other location (preferably the same model) just treat both locations as one network, leaving our host IPs the same throughout the move? Renumbering the servers when they move isn't a big deal, but our wireless terminals for order picking in the warehouse have fixed IPs (and a fixed IP, non-DNS reference to the host they speak with) and would be a massive undertaking to reconfigure when the servers move (each device would have to be reconfigured at least 2 times -- some when we start using them in the new building and the host is still here, all of them in both locations when the host moves to the new building, and the rest when they finally make the move to the new building). We're trying to avoid that if possible.

  Read the article

• Unable to Connect to just Google Servers

  - by Akshat Mittal

  I am in an extremely strange problem. I am unable to connect to just Google Servers. I am not able to access any site related to Google, Google.com | YouTube | Google+ | Webmaster Tools | jQuery CDN, nothing is working. I am able to open any other website (as I am posting this question on SuperUser), even the Google DNS (8.8.8.8 and 8.8.4.4) are offline. Please Help!! Update 1: Google DNS are back online, YouTube is back online. But website on domain google.com is not working (ex: play.google.com, maps.google.com, google.com/search, etc). Update 2: I am able to access Google.com (only) with (one of) its IP addresss(s) listed below: 74.125.227.41 74.125.227.46 74.125.227.32 74.125.227.33 74.125.227.34 74.125.227.35 74.125.227.36 74.125.227.37 74.125.227.38 74.125.227.39 74.125.227.40 Update 3: I consulted my friends nearby and they said that they are also experiencing the same problem. Seams like this is a major problem in this area (or India !!) The Problem is Now Solved!! I am able to open Google.com

  Read the article

• IPtables - Accept Arbitrary Packets

  - by Asad Moeen

  I've achieved a lot on blocking attacks on GameServers but I'm stuck on something. I've blocked major requests of game-server which it aceepts in the form "\xff\xff\xff\xff" which can be followed by the actual queries like get status or get info to make something like "\xff\xff\xff\xff getstatus " but I see other queries if sent to the game-server will cause it to reply with a "disconnect" packet with the same rate as input so if the input rate is high then the high output of "disconnect" might give lag to the server. Hence I want to block all queries except the ones actual clients use which I suppose are in the form "\xff\xff\xff\xff" or .... so, I tried using this rule : -A INPUT -p udp -m udp -m u32 ! --u32 0x1c=0xffffffff -j ACCEPT -A INPUT -p udp -m udp -m recent --set --name Total --rsource -A INPUT -p udp -m udp -m recent --update --seconds 1 --hitcount 20 --name Total --rsource -j DROP Now where the rule does accept the clients but it only blocks requests in the form "\xff\xff\xff\xff getstatus " ( by which GameServer replies with status ) and not just "getstatus " ( by which GameServer replies with disconnect packet ). So I suppose the accept rule is accepting the simple "string" as well. I actually want it to also block the non-(\xff) queries. So how do I modify the rule?

  Read the article

• Dynamic DNS Updates with Wireless and Wired interfaces

  - by Phaedrus

  We have offices full of Windows & Mac users who obtain IP addresses from a Windows DHCP server, which in turn updates Dynamic DNS entries. We are noticing major inconsistencies with the entries, and have found that the problem is occurring more on Macs than on windows, and even more when users are frequently switching from wired to wireless adapter, which makes sense, as this sequence occurs: User enables wired adapter and registers Proper DNS User enables wireless adapter and registers 2nd proper DNS entry user switches off wireless manually and 2nd entry remains improperly until scavenge. Our help desk folks rely heavily (maybe more than they should) on the dynamic entries as part of their business process. For example, the user submits a help desk ticket, and the staff member expects to be able to remote desktop to their machine by hostname, which is hyperlinked in the helpdesk ticketing app. We have implemented multiple solutions & band-aids to different symptoms of the problems such as: Using DNS Reservations for Macintosh PCs Using DNS Scavenging to remove old records Switching from a Cisco DHCP server to the Windows DHCP Server But no matter what we do, it seems impossible to maintain perfect records. Has anyone encountered this problem before? What is industry best practice? Comments & Suggestions are much appreciated, /P

  Read the article

• Apache 2: Mod_Rewrite Help - If/else for directory exists

  - by BHare

  This is my current and sloppy Apache 2 mod_rewrite. Keep in mine the part with site1 site2..etc has about 50 sites. RewriteEngine on RewriteCond %{HTTP_HOST} ^([^.]+)\.mainsite\.org$ RewriteCond /home/%1/ -d RewriteRule ^(.+) %{HTTP_HOST}$1 RewriteRule ^([^.]+)\.mainsite\.org/media/(.*) /home/$1/special/media/$2 RewriteRule ^([^.]+)\.mainsite\.org/(.*) /home/$1/www/$2 RewriteCond %{HTTP_HOST} ^mainsite\.org$ [NC] RewriteRule ^(.*)$ http://www.mainsite.org$1 [R=302] RewriteCond %{HTTP_HOST} (site1|site2|site3|site4)\.(com|net|biz|org|us)$ [NC] RewriteCond %{REQUEST_URI} !^/media/ RewriteRule ^/(.*)$ /home/%1/www/$1 RewriteCond %{HTTP_HOST} (site1|site2|site3|site4)\.(com|biz|net|org|us)$ [NC] RewriteRule ^/media/(.*)$ /home/%1/special/media/$1 RewriteCond %{REQUEST_URI} favicon.ico$ RewriteRule ^(.*)$ /misc/favicon.ico So if someone tries to go to theirusername.mainsite.org it will check if /home/theirusername/ exists, and if it does use their www (/home/theirusername/www/) as the file location for web files. If they try they try to access theirusername.mainsite.org/media/ it will make a special file location to look for the file(s) at /home/theirusername/special/media/ I would like it if the username did NOT have /home/username that it would automatically default to www.mainsite.org. I am having a hard time understanding how to do skips and such. so: If someone went to notrealusername.mainsite.org/forum/ it would auto direct to www.mainsite.org/forum/ Extra: I am using repetitive code for other site for example lets say foobar has a website foobar.com, it goes through the same process as mainsite.org so figured maybe having something like: RewriteCond %{HTTP_HOST} ^([^.]+).(mainsite.org|com|net|biz|org)$ where I could have one major rule for all existing domains who have a /home/

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• How to create a software raid5 array without a spare

  - by Yannick M.

  I am trying to create a software raid5 array using mdadm: $ linux # mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 --spare-devices=0 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 mdadm: layout defaults to left-symmetric mdadm: chunk size defaults to 64K mdadm: array /dev/md0 started. However when inspecting /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sdd1[4] sdc1[2] sdb1[1] sda1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 0.3% (2970496/976759936) finish=186.1min speed=87172K/sec unused devices: <none> It seems one drive isn't active, so I check the details of the array: /dev/md0: Version : 00.90.03 Creation Time : Tue Jul 21 16:29:53 2009 Raid Level : raid5 Array Size : 2930279808 (2794.53 GiB 3000.61 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Jul 21 16:29:53 2009 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 0% complete UUID : ce8b2f40:821d003c:0027688e:a70977ec Events : 0.1 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 4 8 49 3 spare rebuilding /dev/sdd1 And it seems there are only 3 active devices, with one spare. Is it just me, or something wrong here?

  Read the article

• 553-Message filtered - HELO Name issue?

  - by g18c

  I am having major issues sending from my SBS2011 machine to Message labs server-13.tower-134.messagelabs.com #553-Message filtered. Refer to the Troubleshooting page at 553-http://www.symanteccloud.com/troubleshooting for more 553 information. (#5.7.1) ## I have changed the IP and hostnames from the below. I am not on any IP or domain blacklists. I have setup SPF (which includes mailchimp servers): v=spf1 mx a ip4:95.74.157.22/32 a:remote.mydomain.com include:servers.mcsv.net ~all I am sure i have setup my HELO names correctly under the Exchange Management console, sending a test email from the SBS server and looking at the header shows the following: X-Orig-To: [email protected] X-Originating-Ip: [95.74.157.22] Received: from [95.74.157.22] ([95.74.157.22:52194] helo=remote.mydomain.com) by smtp50.gate.ord1a.rsapps.net (envelope-from <[email protected]>) (ecelerity 2.2.3.49 r(42060/42061)) with ESMTP id 11/90-10010-E529C835; Mon, 02 Jun 2014 11:04:09 -0400 Received: from MYSBSSVR.mydomain.local ([fe80::3159:95a6:23f:1bef]) by MYSBSSVR.mydomain.local ([fe80::3159:95a6:23f:1bef%10]) with mapi id 14.01.0438.000; Mon, 2 Jun 2014 19:03:56 +0400 Is is the main helo name there OK and do i need to worry about the second Received block where the MYSBSVR.mydomain.local is mentioned? I have asked the ISP to set the reverse DNS for my IP to remote.mydomain.com but they have instead put remote.MYDOMAIN.com - would this case cause HELO lookups to classify this as not matching? Anything else I can do to find out why i am being filtered?

  Read the article

• IIS 7.5 returning 404 for unknown host names

  - by WaldenL

  This just doesn't seem correct to me, so I'm looking for someone to tell me how I've misconfigured IIS... Configuration is IIS7.5 (2008R2), without SP1. I have IIS 7.5 configured w/several sites. ALL sites have hostnames defined in the bindings, there is NO site w/out a hostname. However, if I request an unknown hostname from the server IIS (technically Microsoft-HTTPAPI/2.0) return a 404 error, not a 400 error. I would expect a 400 (or some other major error) rather than a lowly 404. This causes a problem when I have nginx in front of multiple IISs and want to stop a site so nginx takes it out of rotation. Since IIS still returns a 404 for the request even when there is no active site for that name, nginx doesn't know the server is dead. NB: IIS returns the 404 regardless of whether there is a server, but it's stopped, or there is no server. Thoughts? Solutions? -- Additional info: OK, I added a site on a port other than 80 (5000) and then on a connection to that port asked for a site that doesn't exist, and I get the expected error 400 (Invalid hostname). So, while IIS isn't listening for generic (no host name) connections on port 80 it would seem that something is. Any ideas how to get HTTPSys to dump the list of what it's listening for?

  Read the article

• How to re-add a RAID-10 failed drive on Ubuntu?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• How do I reinitialise a failed RAID 5 drive using terminal on Ubuntu Server

  - by Stephen

  I've currently put together a new system and part of that has been creating a software RAID 5 using 'mdadm' in Ubuntu Server. I successfully got to the point where I create the array using: sudo mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 I left it to do its thing overnight then used the following command to check on it: watch cat /proc/mdstat To which the following was returned: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[4](S) sdc1[2] sdb1[1] sda1[0](F) 5860535808 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/2] [_UU_] unused devices: <none> It appears that one has failed (and I'm not too savvy with why another is a spare). So, just to be sure that something else isn't amiss I wanted to try and re-engage the failed drive. Can someone explain how I can do that and what I should do with the spare (if anything). And also how do I know when synchronisation is complete? The tutorial I used to get this far is located here: http://sonniesedge.co.uk/2009/06/13/software-raid-5-on-ubuntu-904/ Many thanks! p.s. Here is some extra information that may help: sudo mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Mon Jun 18 21:14:21 2012 Raid Level : raid5 Array Size : 5860535808 (5589.04 GiB 6001.19 GB) Used Dev Size : 1953511936 (1863.01 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Mon Jun 18 21:50:26 2012 State : clean, FAILED Active Devices : 2 Working Devices : 3 Failed Devices : 1 Spare Devices : 1 Layout : left-symmetric Chunk Size : 512K Name : myraidbox:0 (local to host myraidbox) UUID : a269ee94:a161600c:fb1665e7:bd2f27b3 Events : 13 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 3 0 0 3 removed 0 8 1 - faulty spare /dev/sda1 4 8 49 - spare /dev/sdd1

  Read the article

• How to correctly set GNU Screen to display currently running program in hardstatus

  - by johnny_bgoode

  I posted this question on SuperUser but it's hardly getting any views, so I thought I'd ask here as well. In bash, to display the name of the current program in the GNU Screen hardstatus line takes only two configuration lines. First, tell screen what the end of your prompt normally looks like, and supply a default title for a window when you are sitting at in the shell: shelltitle "$ |bash" Next, place this escape sequence in the PS1 variable, before the characters that normally terminate the prompt '$ ' in this case: \033k\033\\\ This technique works, to a point. The hardstatus window title is updated to the name of the currently running program, and then switches back to the default title shortly after execution is finished. One major problem, however, is that this escape string is not escaped itself, causing line-wrapping problems with commands longer than the initial line. This was annoying, so I set out looking for a solution. Turns out, simply escaping the previous escape sequence corrects line wrapping: [\033k]\[\033\\\] Great! My hardstatus window title still updates to the name of the currently running program, and now my longer commands wrap to the second line correctly. However, with this new escape sequence in my PS1, screen updates the window title to the actual command I am typing, not simply the name of the current program once it is executed. I am wondering, has anyone gotten this working correctly - i.e. line wrapping and proper updating of the hardstatus window title? Thanks!

  Read the article

• How to correctly set GNU Screen to display currently running program in hardstatus

  - by johnny_bgoode

  In bash, to display the name of the current program in the GNU Screen hardstatus line takes only two configuration lines. First, tell screen what the end of your prompt normally looks like, and supply a default title for a window when you are sitting at in the shell: shelltitle "$ |bash" Next, place this escape sequence in the PS1 variable, before the characters that normally terminate the prompt '$ ' in this case: \033k\033\\ This technique works, to a point. The hardstatus window title is updated to the name of the currently running program, and then switches back to the default title shortly after execution is finished. One major problem, however, is that this escape string is not escaped itself, causing line-wrapping problems with commands longer than the initial line. This was annoying, so I set out looking for a solution. Turns out, simply escaping the previous escape sequence corrects line wrapping: \[\033k\]\[\033\\\] Great! My hardstatus window title still updates to the name of the currently running program, and now my longer commands wrap to the second line correctly. However, with this new escape sequence in my PS1, screen updates the window title to the actual command I am typing, not simply the name of the current program once it is executed. I am wondering, has anyone gotten this working correctly - i.e. line wrapping and proper updating of the hardstatus window title?

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >