Search Results

Search found 35142 results on 1406 pages for 'latest version'.

Page 992/1406 | < Previous Page | 988 989 990 991 992 993 994 995 996 997 998 999  | Next Page >

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• PanelGridLayout - A Layout Revolution

  - by Duncan Mills

  With the most recent 11.1.2 patchset (11.1.2.3) there has been a lot of excitement around ADF Essentials (and rightly so), however, in all the fuss I didn't want an even more significant change to get missed - yes you read that correctly, a more significant change! I'm talking about the new panelGridLayout component, I can confidently say that this one of the most revolutionary components that we've introduced in 11g, even though it sounds rather boring. To be totally accurate, panelGrid was introduced in 11.1.2.2 but without any presence in the component palette or other design time support, so it was largely missed unless you read the release notes. However in this latest patchset it's finally front and center. Its time to explore - we (really) need to talk about layout.  Let's face it,with ADF Faces rich client, layout is a rather arcane pursuit, once you are a layout master, all bow before you, but it's more of an art than a science, and it is often, in fact, way too difficult to achieve what should (apparently) be a pretty simple. Here's a great example, it's a homework assignment I set for folks I'm teaching this stuff to:  The requirements for this layout are: The header is 80px high, the footer is 30px. These are both fixed.  The first section of the header containing the logo is 180px wide The logo is centered within the top left hand corner of the header  The title text is start aligned in the center zone of the header and will wrap if the browser window is narrowed. It should be aligned in the center of the vertical space  The about link is anchored to the right hand side of the browser with a 20px gap and again is center aligned vertically. It will move as the browser window is reduced in width. The footer has a right aligned copyright statement, again middle aligned within a 30px high footer region and with a 20px buffer to the right hand edge. It will move as the browser window is reduced in width. All remaining space is given to a central zone, which, in this case contains a panelSplitter. Expect that at some point in time you'll need a separate messages line in the center of the footer.  In the homework assigment I set I also stipulate that no inlineStyles can be used to control alignment or margins and no use of other taglibs (e.g. JSF HTML or Trinidad HTML). So, if we take this purist approach, that basic page layout (in my stock solution) requires 3 panelStretchLayouts, 5 panelGroupLayouts and 4 spacers - not including the spacer I use for the logo and the contents of the central zone splitter - phew! The point is that even a seemingly simple layout needs a bit of thinking about, particulatly when you consider strechting and browser re-size behavior. In fact, this little sample actually teaches you much of what you need to know to become vaguely competant at layouts in the framework. The underlying result of "the way things are" is that most of us reach for panelStretchLayout before even finishing the first sip of coffee as we embark on a new page design. In fact most pages you will see in any moderately complex ADF page will basically be nested panelStretchLayouts and panelGroupLayouts, sometimes many, many levels deep. So this is a problem, we've known this for some time and now we have a good solution. (I should point out that the oft-used Trinidad trh tags are not a particularly good solution as you're tie-ing yourself to an HTML table based layout in that case with a host of attendent issues in resize and bi-di behavior, but I digress.) So, tadaaa, I give to you panelGridLayout. PanelGrid, as the name suggests takes a grid like (dare I say slightly gridbag-like) approach to layout, dividing your layout into rows and colums with margins, sizing, stretch behaviour, colspans and rowspans all rolled in, all without the use of inlineStyle. As such, it provides for a much more powerful and consise way of defining a layout such as the one above that is actually simpler and much more logical to design. The basic building blocks are the panelGridLayout itself, gridRow and gridCell. Your content sits inside the cells inside the rows, all helpfully allowing both streching, valign and halign definitions without the need to nest further panelGroupLayouts. So much simpler!  If I break down the homework example above my nested comglomorate of 12 containers and spacers can be condensed down into a single panelGrid with 3 rows and 5 cell definitions (39 lines of source reduced to 24 in the case of the sample). What's more, the actual runtime representation in the browser DOM is much, much simpler, and clean, with basically one DIV per cell (Note that just because the panelGridLayout semantics looks like an HTML table does not mean that it's rendered that way!) . Another hidden benefit is the runtime cost. Because we can use a single layout to achieve much more complex geometries the client side layout code inside the browser is having to work a lot less. This will be a real benefit if your application needs to run on lower powered clients such as netbooks or tablets. So, it's time, if you're on 11.1.2.2 or above, to smile warmly at your panelStretchLayouts, wrap the blanket around it's knees and wheel it off to the Sunset Retirement Home for a well deserved rest. There's a new kid on the block and it wants to be your friend. 

  Read the article

• Tor Browser Failing to Load

  - by Ben

  Dec 12 22:32:25.313 [notice] Tor v0.2.3.22-rc (git-4a0c70a817797420) running on Linux. Dec 12 22:32:25.313 [notice] Tor can't help you if you use it wrong! Learn how to be safe at https://www.torproject.org/download/download#warning Dec 12 22:32:25.313 [notice] Read configuration file "/etc/tor/torrc". Dec 12 22:32:25.319 [notice] Initialized libevent version 2.0.19-stable using method epoll (with changelist). Good. Dec 12 22:32:25.319 [notice] Opening Socks listener on 127.0.0.1:9050 Dec 12 22:32:25.319 [warn] Could not bind to 127.0.0.1:9050: Address already in use. Is Tor already running? Dec 12 22:32:25.319 [warn] Failed to parse/validate config: Failed to bind one of the listener ports. Dec 12 22:32:25.319 [err] Reading config failed--see warnings above. I've tried reinstalling it and I always get this error after powering off and back on, despite it working fine directly after the install...

  Read the article

• ArchBeat Link-o-Rama for 2012-10-09

  - by Bob Rhubart

  SOA Suite create partition in Enterprise Manager | Peter Paul van de Beek "In Oracle SOA Suite 10g, or more specific BPEL 10g, one could group functionality in domains," says Peter Paul van de Beek. "This feature has been away in the early versions of SOA Suite 11g. They have returned in more recent version and can be used for all SCA composites (instead of BPEL only). Nowadays these 10g domains are called partitions." OOW12: Oracle Business Process Management/Oracle ADF Integration Best Practices | Andrejus Baranovskis The Oracle OpenWorld presentations keep coming! Oracle ACE Director Andrejus Baranovskis shares the slides from "Oracle Business Process Management/Oracle ADF Integration Best Practices," co-presented with Danilo Schmiedel from Opitz Consulting. My presentations at Oracle Open World 2012 | Guido Schmutz The list of #OOW participants sharing their presentations grows with this post from Oracle ACE Director Guido Schmutz. You'll find Slideshare links to his presentations "Oracle Fusion Middleware Live Application Development (UGF10464)" and "Effective Fault handling in SOA Suite 11g (CON4832)." HTML Manifest for Content Folios | Kyle Hatlestad Kyle Hatlestad, solutions architect with the Oracle Fusion Middleware A-Team, shares the details on "a project to create a custom content folio renderer in WebCenter Content." Adaptive ADF/WebCenter template for the iPad | Maiko Rocha Oracle Fusion Middleware A-Team member Maiko Rocha responds to a a customer request for information about how to create an adaptive iPad template for their WebCenter Portal application, "a specific template to streamline their workflow on the iPad." Thought for the Day "I loved logic, math, computer programming. I loved systems and logic approaches. And so I just figured architecture is this perfect combination." — Maya Lin Source: Brainy Quote

  Read the article

• First Experience with Web Services

  When I first started programming with Microsoft .Net (1.0 Framework) I had a strong desire to learn how search engines indexed web sites. At that time I was a working as a search engine spammer creating web pages to generate traffic for specific themes for various clients. One way I attempted to better understand .Net was to build a web spider that analyzed web pages on demand. An example of the spider is hosted at AddLinkz.com. After my spider was built I had no real idea what I could/should do with it until I found the MSN Search API. I used this web service to compare its results with my spider. Additionally, I used the API to feed my .Net web spider new URLs from the API based on specific search terms. MSN’s search API was very easy to use, I just had to request information by calling a web URL with parameters via a Get request and the results were returned in XML. At that time all requests were limited to XML responses and a maximum of 1,000 results per query.   Since then the entire API has gone through several reconstructions, rebranding and new search services.  Microsoft’s new Bing API replaced the older MSN search API and added several new search capabilities. These new features allow search data to be returned for web searches, image searches, new searches, and related search terms to name a few. Bing API Version 2.0 SourceTypes Web Searches for web content Sushi Image Searches for images on the web Sushi News Searches news stories Sushi InstantAnswer Searches Encarta online what is sushi, convert 5 feet to meters, x*5=7, and 2 plus 2 Spell Searches Encarta dictionary for spelling suggestions Phonebook Searches phonebook entries sushi in Los Angeles RelatedSearch Returns the query strings most similar to yours Ad Returns advertisements to incorporate with results I currently plan to start using the web search feature from the new Bing 2.0 API in an open source project related to exception management. Currently, it is still in the conception phase.

  Read the article

• Join our team at Microsoft

  - by Daniel Moth

  If you are looking for a SDE or SDET job at Microsoft, keep on reading. Back in January I posted a Dev Lead opening on our team, which was quickly filled internally (by Maria Blees). Our team is part of the recently announced Microsoft Technical Computing group. Specifically, we are working on new debugger functionality, integrated with Visual Studio (we are starting work on the next version), aimed to address HPC and GPGPU scenarios (and continuing the Parallel Debugging scenarios we started addressing with VS2010). We now have many more openings on our debugger team. We posted three of those on the careers website: Software Development Engineer Software Development Engineer II Software Development Engineer in Test II (don't let the word "Test" fool you: An SDET on our team is no different than a developer in any way, including the skills required) Please do read the contents of the links above. Specifically, note that for both positions you need to be as proficient in writing C++ code as you are with managed code (WPF experience is a plus). If you think you have what it takes, you wish to join a quality and schedule driven project, and want to contribute features to a product that has global impact, then send me your resume and I'll pass it on to the hiring managers. Comments about this post welcome at the original blog.

  Read the article

• computer shows up twice, connection unknown

  - by Thomas G. Seroogy

  added two computers to Ubuntu One. One machine is windows. The windows version seems to work fine, and I started syncing a folder by placing it into the Ubuntu One folder. All files and folders are visible when I go to my account online. On Ubuntu machine. I selected to sync the Download folder. Shortly thereafter, I realized that one folder exceeded my storage max. I tried to un-sync the folder, but Ubuntu One and the Stop Syncing This Folder were not visible in the menu. Per Ubuntu instructions, I removed my Ubuntu computer from the list of syncing computers. Per Ubuntu instructions, I re-added the Ubuntu computer. However, I find that two computers by the same name are added on both the desktop app and on the web. Plus, I the connection is "unknown." I have removed and re-added the computer several times with the same results. In all cases, I remove the computers using the Ubuntu One desktop app, then removing them from my account on the web, removing the Ubuntu One password, and restart the Ubuntu One app. Problem remains. Thanks in advance for any replies and help.

  Read the article

• Infrastructure to effectively set up experiements and learn from them

  - by David

  Open-org.com is in the early stages of creating our first product, a place on the web, where one can ask lawyers questions at a fraction of their normal costs. An early stage front page can be found here. I got inspired by this video, which is recommended by Jeff Atwood, which talks about getting feedback faster, which is the reason for this question. The problem Needless to say, we want our conversion rates to be as high as possible. Therefore, we want to be able to rapidly set up a new experiment where we change something on the site (like moving an image slightly, rewriting a sentence etc.). We then want to present the modified page to a random subset of the users. After that we will compare the conversion rates of the experiment with another version. I could very well imagine that we want to run 10-100 experiments simultaneously and it would be nice to have features, where experiments that obviously have worse results will be ended before schedule. My question Does infrastructure to support the whole process exist? A short description of our infrastructure... We use EC2 and PHP and have a script to automatically start up new instances with all needed software. Still, starting up a new server for every experiment, seems like a bit of overkill, so I am wondering what other options exist. Btw. If you feel like working for Open-org.com, you can pick a task, and start working, or suggest a new task. All profits are given out to the contributors.

  Read the article

• Accessing a Web Service: Learning Resource needed

  - by abel

  I have been searching for resources to learn (Java) Web Services. Although I have found a lot of resources and tutorials on JWS, I am confused with the version numbers, the abbreviations and Metro. Plus the last update to Metro was in 2008. Is it a worthwile thing to learn? I wanted to learn how to access Web Services, since an upcoming project is about accessing one. I have some experience with OAuth on Twitter(using code available). Things I know about the project: I have to access a Web Service. Java is the preferred platform to use(Although I know I can use any). Axis can be used to access the Web Service(I have never used Axis) I have a meeting scheduled to learn more, but I sure don't want to look silly since I am no Java expert, have never created or accessed Web Services using Java. My Questions: 1.Can someone point me to a tutorial which will help me learn how to access a already running Web Service (Preferably SOAP(?), not REST. It's XML based) 2. Will you recommend using PHP or Python to do the work of accessing the web service? I am expecting a lot of nay saying, but I hope I get some answers too. I will clarify things if needed.

  Read the article

• Ubuntu 13.10 No Sound

  - by spiersie

  I was running 13.04 since last monday and just today i upgraded to 13.10, in both of these version i have not managed to get my sound working. I have gone into alsamixer and disabled auto mute and the volumes are up. However if somebody thinks they can help me fix this i will gladly follow any steps. Please lay specifically any terminal commands you need me to do to either show specs or solve the problem as i am not fluent with the linux commands, this desktop being my first system to run linux, starting last monday. blake@Blake-Ubuntu-PC:~$ lspci -v | grep -A7 -i "audio" 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller Subsystem: ASUSTeK Computer Inc. Device 8526 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at fef44000 (32-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) (prog-if 30 [XHCI]) 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 01) Subsystem: ASUSTeK Computer Inc. Device 8445 Flags: bus master, slow devsel, latency 32, IRQ 16 Memory at fef40000 (64-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)

  Read the article

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• Graph data structures and journal format for mini-IDE

  - by matec

  Background: I am writing a small/partial IDE. Code is internally converted/parsed into a graph data structure (for fast navigation, syntax-check etc). Functionality to undo/redo (also between sessions) and restoring from crash is implemented by writing to and reading from journal. The journal records modifications to the graph (not to the source). Question: I am hoping for advice on a decision on data-structures and journal format. For the graph I see two possible versions: g-a Graph edges are implemented in the way that one node stores references to other nodes via memory address g-b Every node has an ID. There is an ID-to-memory-address map. Graph uses IDs (instead of addresses) to connect nodes. Moving along an edge from one node to another each time requires lookup in ID-to-address map. And also for the journal: j-a There is a current node (like current working directory in a shell + file-system setting). The journal contains entries like "create new node and connect to current", "connect first child of current node" (relative IDs) j-b Journal uses absolute IDs, e.g. "delete edge 7 - 5", "delete node 5" I could e.g. combine g-a with j-a or combine g-b with j-b. In principle also g-b and j-a should be possible. [My first/original attempt was g-a and a version of j-b that uses addresses, but that turned out to cause severe restrictions: nodes cannot change their addresses (or journal would have to keep track of it), and using journal between two sessions is a mess (or even impossible)] I wonder if variant a or variant b or a combination would be a good idea, what advantages and disadvantages they would have and especially if some variant might be causing troubles later.

  Read the article

• Devoxx 2011 Started Today

  - by Yolande

  Devoxx 2011, organized by Java user group in Belgium, is the biggest Java conference in Europe. The first two University Days set the tone for the weeklong conference with its in-depth technical sessions lead by luminaries from the Java community and industry experts. Each day is a great mix of 3 hour sessions and hands-on labs, 30 minute Tools-in-Action sessions giving tips for faster and better application development and the traditional Birds-of-a-Feather sessions in the evening. Java sessions for today and tomorrow: - Next Gen Enterprise Apps - Bert Ertman and Paul Bakker talked about new Java EE 6 APIs that reduces the need for boilerplate code and configuration. - JavaFX 2.0 – A Java developer’s guide - Stephen Chin and Peter Pilgrim will give an overview of new version and how Java developers can take advantage of it - Java Rich Clients with JavaFX 2.0 - Richard Bair and Jasper Potts will get into JavaFX 2.0 APIs - Building an end-to-end application using Java EE 6 and NetBeans - Arun Gupta will showcase how to write Java EE 6 applications more effectively. - The OpenJDK Community BOF with Dalibor Topic Starting Tuesday, come by the Oracle booth to chat about technology, enter our raffle and have a beer every day at 18:45 The sessions will be available on Parleys website after the conference. In the meantime, you can learn a lot about those Java technologies on our website: - JavaFX 2.0 tutorials and documentation - OpenJDK - News from the GlassFish community - JavaEE 6 resources - JavaOne sessions

  Read the article

• Update Since Microsoft/PSC Office Open XML Case Study

  - by Tim Murphy

  In 2009 Microsoft released a case study about a project that we had done using the OOXML SDK 1.0 for Research Directors Inc.  Since that time Microsoft has released version 2.0 of the SDK and PSC has done significant development with it.  Below are some of the mile stones we have reached since the original case study. At the time of the original case study two report types had been automated to output as PowerPoint presentations.  Now that the all the main products have been delivered we have added three reports with Word document outputs and five more reports with PowerPoint outputs. One improvement we made over the original application was to create a PowerPoint Add-In which allows the users to tag a slide.  These tags along with the strongly typed SDK 2.0 allows for the code to use LINQ to easily search for slides in the template files.  This allows for a more flexible architecture base on assembling a presentation from copied slide extracted from the template. The new library we created also enabled us to create two new Word based reports in two weeks.  The library we created abstracts the generation of the documents from the business logic and the data retrieval.  The key to this is the mark up.  Content Controls are a good method for identifying sections of a template to be modified or replaced.  Join this with the concept of all data being generically either scalar or two dimensional and the code becomes more generic. In the end we found the OOXML SDK 2.0 to be a great tool for accelerating document generation development and creating happy clients.  del.icio.us Tags: PSC Group,OOXML,Case Study,Office Open XML,Word,PowerPoint

  Read the article

• Connecting to wireless networks from command line

  - by Balaji

  I need to write a shell script which connects to one of the two available wi-fi connections. One is a un secure connection and the other is secure connection. My question has 2 parts- 1.How to connect to the un-secure (un-encrypted and no password required) connection from command line (or by executing a shell script) when I'm connected to the secure connection? I followed the steps in http://www.ubuntugeek.com/how-to-troubleshoot-wireless-network-connection-in-ubuntu.html for in-secure connection. I put all the commands in a script and executed it (I made sure that interface name and essid are correct) - sudo dhclient -r wlan0 - sudo ifconfig wlan0 up - sudo iwconfig wlan0 essid "UAPublic" - sudo iwconfig wlan0 mode Managed - sudo dhclient wlan0 But nothing happens - I'm not disconnected from the current network and connected to the new one 2.When I want to connect to the secure wi-fi network, I understand from http://askubuntu.com/a/138476/70665 that I need to use wpa_supplicant. But I enter a lot of details in the interface when I connect via UI security : wpa and wpa2 enterprise Authentication : PEAP CA certificate : Equifax... PEAP version : automatic inner authentication : MSCHAPv2 username : password : How to use wpa_supplicant to mention all these details in the command line? The conf file network={ ssid="ssid_name" psk="password" } doesn't work for me.

  Read the article

• Updates broke my themes/shell [Ubuntu 12.04 running Gnome 3 ]

  - by APNW

  I am running gnome-session 3.4.2.1. After the latest updates (listed below) my theme regressed to what looks like tango - not sure. Am unable to change it using Gnome-tweak tool or the display settings. I am also unable to change the wallpaper. Here's what it looks like: Synaptic: Chromium and this is the wallpaper page even though I have selected the wallpaper, it actually does not change. This same problem occurred on my personal computer, and one other computer I have, all running the same software/config. The interesting thing is that while Gnome 3 and Unity are affected, Cinnamon is not. What I've done so far: purged and re-installed both gnome 3 and Unity- no change noted. So, how do I fix this? Thanks Here's the installation log: Start-Date: 2013-11-07 12:01:28 Upgrade: chromium-browser-l10n:i386 (28.0.1500.71-0ubuntu1.12.04.1, 30.0.1599.114-0ubuntu0.12.04.3), libswscale2:i386 (0.8.6-0ubuntu0.12.04.1, 0.8.8-0ubuntu0.12.04.1), chromium-codecs-ffmpeg:i386 (28.0.1500.71-0ubuntu1.12.04.1, 30.0.1599.114-0ubuntu0.12.04.3), chromium-browser:i386 (28.0.1500.71-0ubuntu1.12.04.1, 30.0.1599.114-0ubuntu0.12.04.3), libpostproc52:i386 (0.8.6-0ubuntu0.12.04.1, 0.8.8-0ubuntu0.12.04.1), libavcodec-extra-53:i386 (0.8.6ubuntu0.12.04.1, 0.8.8ubuntu0.12.04.1), libavformat53:i386 (0.8.6-0ubuntu0.12.04.1, 0.8.8-0ubuntu0.12.04.1), libavutil-extra-51:i386 (0.8.6ubuntu0.12.04.1, 0.8.8ubuntu0.12.04.1) End-Date: 2013-11-07 12:02:00 Start-Date: 2013-11-07 17:32:55 Commandline: aptdaemon role='role-commit-packages' sender=':1.136' Install: libmusicbrainz5-0:i386 (5.0.1-2~precise2), udisks2:i386 (1.98.0-1~precise1), libclutter-gst-1.0-0:i386 (1.5.4-0ubuntu2), libudisks2-0:i386 (1.98.0-1~precise1), cinnamon-session-common:i386 (2.0.4-20131105043005-precise), librhythmbox-core6:i386 (2.97-1ubuntu1~precise1), gcr:i386 (3.4.1-3~precise1), libcluttergesture-0.0.2-0:i386 (0.0.2.1-2ubuntu3), libmx-1.0-2:i386 (1.4.3-0ubuntu1), guile-2.0-libs:i386 (2.0.5+1-1), libclutter-imcontext-0.1-0:i386 (0.1.4-2build1), libnatpmp1:i386 (20110808-3ubuntu1) Upgrade: gnome-keyring:i386 (3.2.2-2ubuntu4.1, 3.4.1-4ubuntu1~precise1), cinnamon:i386 (2.0.6-20131026040307-precise, 2.0.10-20131105040309-precise), gir1.2-muffin-3.0:i386 (2.0.3-20131023003029-precise, 2.0.3-20131105003012-precise), gir1.2-totem-1.0:i386 (3.0.1-0ubuntu21.1, 3.4.3-0ubuntu1~precise1), nemo:i386 (2.0.2-20131023010018-precise, 2.0.5-20131105010007-precise), aisleriot:i386 (3.2.3.2-0ubuntu1, 3.4.1-1~precise1), procps:i386 (3.2.8-11ubuntu6.2, 3.2.8-11ubuntu6.3), libcinnamon-desktop0:i386 (2.0.2-20131025011504-precise, 2.0.3-20131105011505-precise), libgck-1-0:i386 (3.2.2-2ubuntu4.1, 3.4.1-3~precise1), totem-plugins:i386 (3.0.1-0ubuntu21.1, 3.4.3-0ubuntu1~precise1), cinnamon-desktop-data:i386 (2.0.2-20131025011504-precise, 2.0.3-20131105011505-precise), rhythmbox:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), libgcr-3-1:i386 (3.2.2-2ubuntu4.1, 3.4.1-3~precise1), seahorse:i386 (3.2.2-0ubuntu2.1, 3.4.1-2~precise1), muffin-common:i386 (2.0.3-20131023003029-precise, 2.0.3-20131105003012-precise), totem-common:i386 (3.0.1-0ubuntu21.1, 3.4.3-0ubuntu1~precise1), libtotem0:i386 (3.0.1-0ubuntu21.1, 3.4.3-0ubuntu1~precise1), rhythmbox-data:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), gir1.2-cinnamondesktop-3.0:i386 (2.0.2-20131025011504-precise, 2.0.3-20131105011505-precise), cinnamon-session:i386 (2.0.1-20131021043004-precise, 2.0.4-20131105043005-precise), rhythmbox-mozilla:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), rhythmbox-plugin-zeitgeist:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), libmuffin0:i386 (2.0.3-20131023003029-precise, 2.0.3-20131105003012-precise), cjs:i386 (2.0.0-20131021020602-precise, 2.0.0-20131105020703-precise), rhythmbox-plugin-cdrecorder:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), cinnamon-common:i386 (2.0.6-20131026040307-precise, 2.0.10-20131105040309-precise), gnome-disk-utility:i386 (3.0.2-2ubuntu7, 3.4.1-0ubuntu1~precise1), nemo-fileroller:i386 (2.0.0-20131021020004-precise, 2.0.0-20131105020003-precise), libnemo-extension1:i386 (2.0.2-20131023010018-precise, 2.0.5-20131105010007-precise), rhythmbox-plugins:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), gimp:i386 (2.8.6-0precise1~ppa, 2.8.8-0precise0~ppa), cinnamon-settings-daemon:i386 (2.0.5-20131026004504-precise, 2.0.6-20131105004505-precise), libgimp2.0:i386 (2.8.6-0precise1~ppa, 2.8.8-0precise0~ppa), gir1.2-rb-3.0:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), wpasupplicant:i386 (0.7.3-6ubuntu2.1, 0.7.3-6ubuntu2.2), libcjs0c:i386 (2.0.0-20131021020602-precise, 2.0.0-20131105020703-precise), nemo-data:i386 (2.0.2-20131023010018-precise, 2.0.5-20131105010007-precise), totem:i386 (3.0.1-0ubuntu21.1, 3.4.3-0ubuntu1~precise1), gimp-data:i386 (2.8.6-0precise1~ppa, 2.8.8-0precise0~ppa), transmission-common:i386 (2.51-0ubuntu1.3, 2.73-0ubuntu1~precise1), cinnamon-translations:i386 (2.0.1-20131021040407-precise, 2.0.1-20131105040807-precise), totem-mozilla:i386 (3.0.1-0ubuntu21.1, 3.4.3-0ubuntu1~precise1), rhythmbox-plugin-magnatune:i386 (2.96-0ubuntu4.3, 2.97-1ubuntu1~precise1), transmission-gtk:i386 (2.51-0ubuntu1.3, 2.73-0ubuntu1~precise1) End-Date: 2013-11-07 17:34:40

  Read the article

• Expanding existing DVCS Wiki

  - by A Lion

  A portion of my job is to maintain technical documentation for a rapidly expanding manufacturing company. Because it is only a portion of my job and the company's product line is expanding so quickly, I can't stay on top of the documentation. As a result, I've been yearning for an information management system with a handful of specific features. I've found many products that have a subset, but none that have all the features I'm looking for. I'm at the point of picking an existing product and expanding it to cover my desired feature set, however, this will be a pet project and I will be learning the underlying language as I go. So, the main question is which existing product will be the easiest to expand to cover the full feature set and has a relatively easy to learn language? Alternatively, have I missed another existing program that will cover the feature set or should be in my list of "close, but not quite there"? Feature Set web interface based on a distributed version control system (e.g., git) easy to edit by logged in novices (e.g. wiki, multimarkdown) outputs in more traditional formats (e.g., doc, odt, pdf) edits held in queue until editor/engineer/manager approves them (e.g., MS Word editing) [this is the really big elephant in list - suggestions on where to start appreciated] edits held in queue specifically for engineer approval [extra limb of the elephant in the list] well-supported in the open source community Closest, but not quite there ikiwiki - http://ikiwiki.info (php) lots of awesome functionality and extensions, including easy to edit and based on DVCS lacks a review/forward for review queue appears to be well-supported within the OSS community gitit - http://gitit.net/ (haskell) easy to edit and based on DVCS lots of outputs in traditional formats a great web-based gui diff interface lacks a review/forward for review queue appears to be primarily maintained by one individual

  Read the article

• Can not login Dashboard / Unable to find the server at mykeystoneurl

  - by neo0

  I installed Dashboard following this guide: http://wiki.openstack.org/OpenStackDashboard Everything fine, but when I run the server, I can not login with the username and password in DATABASE config in local_settings.py. Here's my config: DATABASES = { 'default': { 'ENGINE': 'django.db.backends.mysql', 'NAME': 'dashboarddb', 'USER': 'nova', 'PASSWORD': 'nova', 'HOST': 'localhost', 'default-character-set': 'utf8' }, } When I run the Dashboard server and enter username + password. It returned this error on browser: Unable to find the server at mykeystoneurl (HTTP 400) And in the command line: DEBUG:openstack_dashboard.settings:Running in debug mode without debug_toolbar. DEBUG:openstack_dashboard.settings:Running in debug mode without debug_toolbar. Validating models... 0 errors found Django version 1.3.1, using settings 'openstack_dashboard.settings' Development server is running at http://0.0.0.0:8888/ Quit the server with CONTROL-C. Request returned failure status. Traceback (most recent call last): File "/home/us/horizon/.venv/src/python-keystoneclient/keystoneclient/client.py", line 121, in request body = json.loads(body) File "/usr/lib/python2.7/json/__init__.py", line 326, in loads return _default_decoder.decode(s) File "/usr/lib/python2.7/json/decoder.py", line 366, in decode obj, end = self.raw_decode(s, idx=_w(s, 0).end()) File "/usr/lib/python2.7/json/decoder.py", line 384, in raw_decode raise ValueError("No JSON object could be decoded") ValueError: No JSON object could be decoded [06/Mar/2012 15:20:03] "POST /auth/login/ HTTP/1.1" 200 3735 I also tried login as "admin" with password is "password" or "secrete" but I didn't work. What's wrong? Thank you!

  Read the article

• javaws crashes, error in ld-linux-x86-64.so.2

  - by user54214

  I am running Ubuntu 11.10 64 bit client as Dom0 and Xen. I am having problems getting java up and running. Java itself seems to work fine, however I get strange errors, for example when I start javaws. I tried different versions and always get the same errors. I tried openjdk 1.6 and 1.7 as well as sunjava6 and 7. I alway get an error in the same lib All other applications are working fine, so it seems ld-linux-x86-64.so.2 is working fine. Any hints what could be wrong? Ubuntu01:~$ javaws # # A fatal error has been detected by the Java Runtime Environment: # # SIGILL (0x4) at pc=0x00007f4e74c5ad10, pid=7974, tid=139974945277696 # # JRE version: 6.0_23-b23 # Java VM: OpenJDK 64-Bit Server VM (20.0-b11 mixed mode linux-amd64 compressedoops) # Derivative: IcedTea6 1.11pre # Distribution: Ubuntu 11.10, package 6b23~pre11-0ubuntu1.11.10.2 # Problematic frame: # C [ld-linux-x86-64.so.2+0x14d10] _dl_make_stack_executable+0x2b70 # # An error report file with more information is saved as: # /home/r/hs_err_pid7974.log # # If you would like to submit a bug report, please include # instructions how to reproduce the bug and visit: # https://bugs.launchpad.net/ubuntu/+source/openjdk-6/ # The crash happened outside the Java Virtual Machine in native code. # See problematic frame for where to report the bug. # Aborted

  Read the article

• Antenna Aligner part 2: Finding the right direction

  - by Chris George

  Last time I managed to get "my first app(tm)" built, published and running on my iPhone. This was really cool, a piece of my code running on my very own device. Ok, so I'm easily pleased! The next challenge was actually trying to determine what it was I wanted this app to do, and how to do it. Reverting back to good old paper and pen, I started sketching out designs for the app. I knew I wanted it to get a list of transmitters, then clicking on a transmitter would display a compass type view, with an arrow pointing the right way. I figured there would not be much point in continuing until I know I could do the graphical part of the project, i.e. the rotating compass, so armed with that reasoning (plus the fact I just wanted to get on and code!), I once again dived into visual studio. Using my friend (google) I found some example code for getting the compass data from the phone using the PhoneGap framework. // onSuccess: Get the current heading // function onSuccess(heading) {    alert('Heading: ' + heading); } navigator.compass.getCurrentHeading(onSuccess, onError); Using the ripple mobile emulator this showed that it was successfully getting the compass heading. But it didn't work when uploaded to my phone. It turns out that the examples I had been looking at were for PhoneGap 1.0, and Nomad uses PhoneGap 1.4.1. In 1.4.1, getCurrentHeading provides a compass object to onSuccess, not just a numeric value, so the code now looks like // onSuccess: Get the current magnetic heading // function onSuccess(heading) {    alert('Heading: ' + heading.magneticHeading); }; navigator.compass.getCurrentHeading(onSuccess, onError); So the lesson learnt from this... read the documentation for the version you are actually using! This does, however, lead to compatibility problems with ripple as it only supports 1.0 which is a real pain. I hope that the ripple system is updated sometime soon.

  Read the article

• New features in SQL Prompt 6.4

  - by Tom Crossman

  We’re pleased to announce a new beta version of SQL Prompt. We’ve been trying out a few new core technologies, and used them to add features and bug fixes suggested by users on the SQL Prompt forum and suggestions forum. You can download the SQL Prompt 6.4 beta here (zip file). Let us know what you think! New features Execute current statement In a query window, you can now execute the SQL statement under your cursor by pressing Shift + F5. For example, if you have a query containing two statements and your cursor is placed on the second statement: When you press Shift + F5, only the second statement is executed:   Insert semicolons You can now use SQL Prompt to automatically insert missing semicolons after each statement in a query. To insert semicolons, go to the SQL Prompt menu and click Insert Semicolons. Alternatively, hold Ctrl and press B then C. BEGIN…END block highlighting When you place your cursor over a BEGIN or END keyword, SQL Prompt now automatically highlights the matching keyword: Rename variables and aliases You can now use SQL Prompt to rename all occurrences of a variable or alias in a query. To rename a variable or alias, place your cursor over an instance of the variable or alias you want to rename and press F2: Improved loading dialog box The database loading dialog box now shows actual progress, and you can cancel loading databases:   Single suggestion improvement SQL Prompt no longer suggests keywords if the keyword has been typed and no other suggestions exist. Performance improvement SQL Prompt now has less impact on Management Studio start up time. What do you think? We want to hear your feedback about the beta. If you have any suggestions, or bugs to report, tell us on the SQL Prompt forum or our suggestions forum.

  Read the article

• Database Migration Scripts: Getting from place A to place B

  - by Phil Factor

  We’ll be looking at a typical database ‘migration’ script which uses an unusual technique to migrate existing ‘de-normalised’ data into a more correct form. So, the book-distribution business that uses the PUBS database has gradually grown organically, and has slipped into ‘de-normalisation’ habits. What’s this? A new column with a list of tags or ‘types’ assigned to books. Because books aren’t really in just one category, someone has ‘cured’ the mismatch between the database and the business requirements. This is fine, but it is now proving difficult for their new website that allows searches by tags. Any request for history book really has to look in the entire list of associated tags rather than the ‘Type’ field that only keeps the primary tag. We have other problems. The TypleList column has duplicates in there which will be affecting the reporting, and there is the danger of mis-spellings getting there. The reporting system can’t be persuaded to do reports based on the tags and the Database developers are complaining about the unCoddly things going on in their database. In your version of PUBS, this extra column doesn’t exist, so we’ve added it and put in 10,000 titles using SQL Data Generator. /* So how do we refactor this database? firstly, we create a table of all the tags. */IF  OBJECT_ID('TagName') IS NULL OR OBJECT_ID('TagTitle') IS NULL  BEGIN  CREATE TABLE  TagName (TagName_ID INT IDENTITY(1,1) PRIMARY KEY ,     Tag VARCHAR(20) NOT NULL UNIQUE)  /* ...and we insert into it all the tags from the list (remembering to take out any leading spaces */  INSERT INTO TagName (Tag)     SELECT DISTINCT LTRIM(x.y.value('.', 'Varchar(80)')) AS [Tag]     FROM     (SELECT  Title_ID,          CONVERT(XML, '<list><i>' + REPLACE(TypeList, ',', '</i><i>') + '</i></list>')          AS XMLkeywords          FROM   dbo.titles)g    CROSS APPLY XMLkeywords.nodes('/list/i/text()') AS x ( y )  /* we can then use this table to provide a table that relates tags to articles */  CREATE TABLE TagTitle   (TagTitle_ID INT IDENTITY(1, 1),   [title_id] [dbo].[tid] NOT NULL REFERENCES titles (Title_ID),   TagName_ID INT NOT NULL REFERENCES TagName (Tagname_ID)   CONSTRAINT [PK_TagTitle]       PRIMARY KEY CLUSTERED ([title_id] ASC, TagName_ID)       ON [PRIMARY])        CREATE NONCLUSTERED INDEX idxTagName_ID  ON  TagTitle (TagName_ID)  INCLUDE (TagTitle_ID,title_id)        /* ...and it is easy to fill this with the tags for each title ... */        INSERT INTO TagTitle (Title_ID, TagName_ID)    SELECT DISTINCT Title_ID, TagName_ID      FROM        (SELECT  Title_ID,          CONVERT(XML, '<list><i>' + REPLACE(TypeList, ',', '</i><i>') + '</i></list>')          AS XMLkeywords          FROM   dbo.titles)g    CROSS APPLY XMLkeywords.nodes('/list/i/text()') AS x ( y )    INNER JOIN TagName ON TagName.Tag=LTRIM(x.y.value('.', 'Varchar(80)'))    END    /* That's all there was to it. Now we can select all titles that have the military tag, just to try things out */SELECT Title FROM titles  INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID  INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  WHERE tagname.tag='Military'/* and see the top ten most popular tags for titles */SELECT Tag, COUNT(*) FROM titles  INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID  INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  GROUP BY Tag ORDER BY COUNT(*) DESC/* and if you still want your list of tags for each title, then here they are */SELECT title_ID, title, STUFF(  (SELECT ','+tagname.tag FROM titles thisTitle    INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID    INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  WHERE ThisTitle.title_id=titles.title_ID  FOR XML PATH(''), TYPE).value('.', 'varchar(max)')  ,1,1,'')    FROM titles  ORDER BY title_ID So we’ve refactored our PUBS database without pain. We’ve even put in a check to prevent it being re-run once the new tables are created. Here is the diagram of the new tag relationship We’ve done both the DDL to create the tables and their associated components, and the DML to put the data in them. I could have also included the script to remove the de-normalised TypeList column, but I’d do a whole lot of tests first before doing that. Yes, I’ve left out the assertion tests too, which should check the edge cases and make sure the result is what you’d expect. One thing I can’t quite figure out is how to deal with an ordered list using this simple XML-based technique. We can ensure that, if we have to produce a list of tags, we can get the primary ‘type’ to be first in the list, but what if the entire order is significant? Thank goodness it isn’t in this case. If it were, we might have to revisit a string-splitter function that returns the ordinal position of each component in the sequence. You’ll see immediately that we can create a synchronisation script for deployment from a comparison tool such as SQL Compare, to change the schema (DDL). On the other hand, no tool could do the DML to stuff the data into the new table, since there is no way that any tool will be able to work out where the data should go. We used some pretty hairy code to deal with a slightly untypical problem. We would have to do this migration by hand, and it has to go into source control as a batch. If most of your database changes are to be deployed by an automated process, then there must be a way of over-riding this part of the data synchronisation process to do this part of the process taking the part of the script that fills the tables, Checking that the tables have not already been filled, and executing it as part of the transaction. Of course, you might prefer the approach I’ve taken with the script of creating the tables in the same batch as the data conversion process, and then using the presence of the tables to prevent the script from being re-run. The problem with scripting a refactoring change to a database is that it has to work both ways. If we install the new system and then have to rollback the changes, several books may have been added, or had their tags changed, in the meantime. Yes, you have to script any rollback! These have to be mercilessly tested, and put in source control just in case of the rollback of a deployment after it has been in place for any length of time. I’ve shown you how to do this with the part of the script .. /* and if you still want your list of tags for each title, then here they are */SELECT title_ID, title, STUFF(  (SELECT ','+tagname.tag FROM titles thisTitle    INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID    INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  WHERE ThisTitle.title_id=titles.title_ID  FOR XML PATH(''), TYPE).value('.', 'varchar(max)')  ,1,1,'')    FROM titles  ORDER BY title_ID …which would be turned into an UPDATE … FROM script. UPDATE titles SET  typelist= ThisTaglistFROM     (SELECT title_ID, title, STUFF(    (SELECT ','+tagname.tag FROM titles thisTitle      INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID      INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID    WHERE ThisTitle.title_id=titles.title_ID    ORDER BY CASE WHEN tagname.tag=titles.[type] THEN 1 ELSE 0  END DESC    FOR XML PATH(''), TYPE).value('.', 'varchar(max)')    ,1,1,'')  AS ThisTagList  FROM titles)fINNER JOIN Titles ON f.title_ID=Titles.title_ID You’ll notice that it isn’t quite a round trip because the tags are in a different order, though we’ve managed to make sure that the primary tag is the first one as originally. So, we’ve improved the database for the poor book distributors using PUBS. It is not a major deal but you’ve got to be prepared to provide a migration script that will go both forwards and backwards. Ideally, database refactoring scripts should be able to go from any version to any other. Schema synchronization scripts can do this pretty easily, but no data synchronisation scripts can deal with serious refactoring jobs without the developers being able to specify how to deal with cases like this.

  Read the article

• Laptop Charger Not Recognised Properly on Samsung NP900X3F

  - by user193732

  Firstly thanks for your time. Secondly, having an issue with my power charger on my Samsung Series 9 NP900X3F. When I boot into Ubuntu with the charger plugged in it recognises it as charging. When I unplug the charger after this it is still says it is charging. If I suspend in Ubuntu then plug/unplug during this suspended state it recognises it, but not during normal running. If I knew a little more I'm sure I could grab logs and find out what the difference between wake on suspend and normal running is, but alas I need help! I also am having issues with my keyboard backlight via the fn keys, but that I care about far less. Thank you very much. Linux mikey-900X3F 3.12.0-031200rc1-generic #201309161735 SMP Mon Sep 16 21:38:21 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux (I upgraded my kernel version to remove heinous horizontal artefacts I was getting) Happy to list more info about my system, ima bit of a noob. I did try searching however I can't find any questions at all about my system or related models with the same issue.

  Read the article

• Develop for Desktop and mobile use?

  - by ran2

  I am in the very beginning of developing an app / desktop program. I want it to be cross-platform and possibly also as a tablet version (preferably Android Icecream sandwich). Note that I need to run it offline. I thought about the following approaches: ADOBE Air, since I do not need much performance. Plus I did some web programming in the past which might be of some use. Afaik it would run on OS X and Windows and should run on mobile OSes, too. Qt. Found some nice Qt based desktop recently and read it also works on android. Plus I like the SDK. HTML5 / JS. Again my web background should help me here. I wont need no sever side scripts, thus it should work without installing anything but a browser. How easy could this be converted into an Android app? There might be a plethora of other (better) ways to do it, but I haven't thought of them yet. Can you help out? How would you create such an application. Would it be better to do some pure desktop client and then create tablet versions? Would you rather start to create a website and worry later on how to turn into an app?

  Read the article

• Designing rules to fight smallpox in Civ-style TBS games

  - by Williham Totland

  TL;DR: How do you design a ruleset for a Civ-style TBS game that prevents city smallpox from being a profitable or viable strategy? Long version: Civ-style games are pretty great. Bringing a civilization from cradle to grave is a great endeavor, and practicing diplomacy with hard-line human players is fun and challenging. In theory. In practice, however, many of these games has, especially in multiplayer, exactly one viable strategy: City smallpox, a.k.a. infinite city spread, a.k.a. covering all available space with 1-citizen cities, packed as tight as they will go. I suppose this could count as emergent gameplay, but still; it could hardly be considered to be in the spirit of the class of game. The Civilization series, of course, is stuck in their more or less fixed rule sets, established with Civilization. Yes, there have been major changes in some respects, but the rules pertaining to city building and maintenance have stayed pretty similar. So the question, then: If you build a ruleset for a TBS from the ground up; what rules should be in place to prevent Infinite City Sprawl from being a viable strategy? Or should ICS be a viable strategy?

  Read the article

< Previous Page | 988 989 990 991 992 993 994 995 996 997 998 999  | Next Page >