Search Results

Search found 4151 results on 167 pages for 'cat man do'.

Page 116/167 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

  • Did I lost my RAID again?

    - by BarsMonster
    Hi! A little history: 2 years ago I was really excited to find out that mdadm is so powerful so it even can reshape arrays so you can start with a smaller array and the grow it as you need. I've bought 3x1Tb drives and made RAID-5. It was fine for a year. Then I bought 2x more, and tried to reshape to RAID-6 out of 5 drives, and due to some mess with superblock versions, lost all content. Had to rebuild it from scratch, but 2Tb of data were gone. Yesterday I bought 2 more drives, and this time I had everything: properly built array, UPS. I've disabled write intent map, added 2 new drives as a spare and run a command to grow array to 7-disk. It started working, but speed was ridiculously slow, ~100kb/sec. AFter processing first 37Mb at such an amasing speed, one of old HDDs fails. I properly shutdown PC and disconnected failed drive. After bootup it appeared it recreated intent map as it was still in mdadm config, so I removed it from config and rebooted again. Now all I see is that all mdadm processes deadlocks, and don't do anything. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1937 root 20 0 12992 608 444 D 0 0.1 0:00.00 mdadm 2283 root 20 0 12992 852 704 D 0 0.1 0:00.01 mdadm 2287 root 20 0 0 0 0 D 0 0.0 0:00.01 md0_reshape 2288 root 18 -2 12992 820 676 D 0 0.1 0:00.01 mdadm And all I see in mdstat is: $ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sdb1[1] sdg1[4] sdf1[7] sde1[6] sdd1[0] sdc1[5] 2929683456 blocks super 1.2 level 6, 1024k chunk, algorithm 2 [7/6] [UU_UUUU] [>....................] reshape = 0.0% (37888/976561152) finish=567604147.2min speed=0K/sec I've already tried mdadm 2.6.7, 3.1.4 and 3.2 - nothing helps. Did I lost my data again? Any suggestions how can I make it work? OS is Ubuntu Server 10.04.2... PS. Needless to say that data is unaccessible - I cannot mount /dev/md0 as save the most valuable data. You can see my disappointment - the very specific thing I was excited about failed twice taking 5Tb of my data with it.

    Read the article

  • Mixed Solaris 10 and 11 versions in logical domains on the same server

    - by jsavit
    One question that comes up frequently is whether you can mix Solaris 10 and Solaris 11 in different logical domains under Oracle VM Server for SPARC. The answer is yes depending only on the system software requirements for the underlying hardware platform. Different versions of Solaris 10 and 11 can exist side-by-side on the same server and can act as control, service, I/O or guest domains subject only to the minimum software levels documented in the System Requirements section of the Oracle VM Server for SPARC Release Notes. Here's an example just taken from a running system. First, here's the control domain, which is running Solaris 10. I've highlighted a guest running Solaris 11. # uname -a SunOS atl-sewr-24 5.10 Generic_147440-01 sun4v sparc SUNW,SPARC-Enterprise-T5220 # ldm -V Logical Domains Manager (v 2.1) Hypervisor control protocol v 1.7 Using Hypervisor MD v 1.3 System PROM: Hypervisor v. 1.10.0 @(#)Hypervisor 1.10.0 2011/04/27 16:19\015 # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-cv- SP 16 4G 1.6% 120d 17h atl-sewr-pool-148 active -n---- 5001 8 2G 0.1% 119d 21h atl-sewr-pool-152 active -n---- 5000 8 4G 0.2% 112d 19h atl-sewr-pool-154 active -n---- 5002 8 2G 0.1% 120d 15h atl-sewr-pool-155 active -n---- 5003 16 2G 0.0% 26d 14h 30m This system is running Oracle VM Server 2.1 with a Solaris 10 control domain. Hmm, I should update this machine to 2.2 when I get a few free moments. Upgrading is very straightforward. Here's a display logging into the highlighted guest: Last login: Mon May 21 10:18:16 2012 from dhcp-adc-twvpn- Oracle Corporation SunOS 5.11 11.0 November 2011 sewr@atl-sewr-pool-152:~$ uname -a SunOS atl-sewr-pool-152 5.11 11.0 sun4v sparc SUNW,SPARC-Enterprise-T5220 sewr@atl-sewr-pool-152:~$ cat /etc/release Oracle Solaris 11 11/11 SPARC Copyright (c) 1983, 2011, Oracle and/or its affiliates. All rights reserved. Assembled 18 October 2011 sewr@atl-sewr-pool-152:~$ sudo virtinfo -ct Password: Domain role: LDoms guest Control domain: atl-sewr-24 sewr@atl-sewr-pool-152:~$ That's running the GA version of Solaris 11, so I probably should update that some time too. Note the use of the virtinfo -ct command that lets the guest get information about the hosting environment. Summary You can mix and match versions of Solaris in logical domains. All the different combinations work: Solaris 10 and/or Solaris 11 control and service domains with Solaris 10 and/or Solaris 11 guests. Mixing different guest OS levels on the same server is one of the traditional reasons for using virtual machines in the first place since virtual machines were invented some 40 years ago, used to run production and test systems in parallel while upgrading OS levels. This can easily be done with Oracle VM Server for SPARC (Logical Domains).

    Read the article

  • Oracle Open World 2012 is Here!

    - by thatjeffsmith
    Just a quick post today and then probably not much more until next week. Speaking, running hands on labs, meets and greets, and trying to keep up with folks like @oraclenerd means I won’t have much time to write until I get home from San Francisco. Wanted to give a quick shout out to my co-worker and partner-in-Product Management-crime, Ashley Chen this morning. She signed me up for a run across the Golden Gate and back with @bamcgill a few months ago…mostly with my permission. The only thing was, I didn’t run at the time, and that’s basically a 5k. But having goals is good. And yesterday I met a big goal of mine – not looking stupid trying to run across the Golden Gate Bridge. Ok, I did the run and mabye looked a little bit stupid. Ashley, Barry, and I Pre-Run Perfect weather and no fog to cloud the view! So the pre-show fun is over and now it’s time for the show fun to begin. At Oracle Open World? Come by our demo pods. We’re with the other Database folks in the back right-hand corner. We’ll have folks on hand to talk and show Oracle SQL Developer, Oracle SQL Developer Data Modeler, Migrations, and Oracle APEX Listener. Oracle SQL Developer Demo Pod I have the full schedule of SQL Developer presentations and hands on labs here. I know there’s a lot of news on tap this week in the world of Oracle, and we’ll start talking more about it soon. So be sure to subscribe to my feed if you don’t want to miss any of my posts. And I promise not to post any more pictures me. Speaking of pictures, thanks to @dmcghan – or as I call him, ‘Dan the Man’ for running with us and being our official portrait photographer! If you don’t follow him, he’s a great fountain of knowledge in the Oracle APEX world and is one of our ACEs.

    Read the article

  • Cooking with Wessty: WordPress and HTML 5

    - by David Wesst
    WordPress is easily one, if not the most, popular blogging platforms on the web. With the release of WordPress 3.x, the potential for what you can do with this open source software is limitless. This technique intends to show you how to get your WordPress wielding the power of the future web, that being HTML 5. --- Ingredients WordPress 3.x Your favourite HTML 5 compliant browser (e.g. Internet Explorer 9) Directions Setup WordPress on your server or host. Note: You can setup a WordPress.com account, but you will require an paid add-on to really take advantage of this technique.Login to the administration panel. Login to the administration section of your blog, using your web browser.  On the left side of the page, click the Appearance heading. Then, click on Themes. At the top of the page, select the Install Themes tab. In the search box, type the “toolbox” and click search. In the search results, you should see an theme called Toolbox. Click the Install link in the Toolbox item. A dialog window should appear with a sample picture of what the theme looks like. Click on the Install Now button in the bottom right corner. Et voila! Once the installation is done, you are done and ready to bring your blog into the future of the web. Try previewing your blog in HTML 5 by clicking the preview link.   Now, you are probably thinking “Man…HTML 5 looks like junk”. To that, I respond: “HTML was never why your site looked good in the first place. It was the CSS.” Now you have an un-stylized theme that uses HTML 5 elements throughout your WordPress site. If you want to learn how to apply CSS to your WordPress blog, you should check out the WordPress codex that pretty much covers everything there is to cover about WordPress development. Now, remember how we noted earlier that your free WordPress.com account wouldn’t take advantage of this technique? That is because, as of the time of this writing, you needed to pay a fee to use custom CSS. Remember now, this only gives you the foundation to create your own HTML 5 WordPress site. There are some HTML 5 themes out there that already look good, and were built using this as the foundation and added some CSS 3 to really spice it up. Looking forward to seeing more HTML 5 WordPress sites! Enjoy developing the future of the web. Resources Toolbox Theme JustCSS Theme WordPress Installation Tutorial WordPress Theme Development Tutorial This post also appears at http://david.wes.st

    Read the article

  • links for 2011-03-17

    - by Bob Rhubart
    Siba Prasad: Oracle Database on Amazon RDSg Siba Prasad share an analysis of the pros and cons. (tags: oracle database cloud amazon) LIVE WEBCAST March 24 2pm PT- Why Switch from Red Hat and SUSE Linux to Oracle Linux? (Oracle's Linux Blog) Featuring Oracle's Monica Kumar, Sr.Director of Linux, Oracle VM and MySQL and Avi Miller, Principal Sales Consultant, Linux and Virtualization. (tags: oracle linux) Webcast: IBM SOA vs. Oracle SOA, March 24, 1pm ET / 10am PT Maneesh Joshi and Bruce Tierney guide you to a solid understanding of the differences between the Oracle and IBM approach to comprehensive SOA. (tags: oracle soa bpm) Finding the Right Solution to Source and Manage Your Contractors (PeopleSoft Apps Strategy) "Talent has become a primary competitive advantage for most organizations. Contingent labor offers talent on flexible terms; it offers the ability to scale up operations, close skill gaps, and manage risk in the process of delivering services." - Mark Rosenberg (tags: oracle peoplesoft enterprisearchitecture) Oracle Business Intelligence Customers: Have Your Voice Heard in the "2011Wisdom of the Crowds Business Intelligence Market Survey" (BI & Analytics Pulse) "The Wisdom of the Crowds survey combines social media, crowd sourcing, and good old fashioned market research to provide vendors and customers alike an unvarnished and insightful snap shot of what's top of mind with business intelligence professionals." (tags: oracle businessintelligence) Martin Bach: Troubleshooting Grid Infrastructure startup Martin Bach hunts down the problem that caused one of his blades to reboot after an EXT3 journal error. (tags: oracle grid rac) Oracle WebCenter: Social Networking & Collaboration (Oracle Enterprise 2.0 Blog) Kelley Ruppel with information on "how the new release of Oracle WebCenter provides unprecedented Social Networking and Collaboration." (tags: oracle webcenter enterprise2.0 collaboration) VirtaThon: 100% Virtual Java/Oracle/MySQL Conference! | Bex Huff "The goal is simple," says Oracle ACE Director Bex Huff. "Because it's all online, the conference is very cheap. Pricing is not yet announced... but it should be around $300. Also, unlike other conferences, every speaker gets paid a small fee depending on the popularity of his or her session." (tags: oracle oracleace java mysqql) Griffiths Waite Blog: BPM 11g PS3 GW's Ian Heathcock shares a link to "a most interesting article on Oracle's recent release discussing the new features and how PS3 adds value  to the whole SOA message." (tags: oracle soa) The Buttso Blathers: Tutorial: JSF 2.0 and JPA 2.0 with WebLogic Server using NetBeans Should you take application architecture advice from a man named Buttso? In this case, yes. (tags: oracle jsf jpa weblogic) Setting-up a High Available Tuned SOA Environment Middleware Magic (tags: ping.fm) How to Configure Weblogic Messaging Bridge with JBoss Middleware Magic (tags: ping.fm Weblogic JBoss) Richard Veryard on Architecture: Emergent Architecture (tags: ping.fm entarch emergence)

    Read the article

  • Why wearing Jeans is considered unprofessional?

    - by Gopinath
    When I started my career 9 years ago I use to wear casual wear to office – Jeans & T-Shirts all the 5 days. The environment at workplace during those days encouraged me to be casual and many of my colleagues use to come in Jeans. We just started our career those days it was perfectly fine to be in casual. As I grow up in the ladder, I started feeling the discomfort of wearing Jeans at work. During clients visits, senior managers meetings and consultations I was an odd man in the crowd as the rest of them are in formals. In order to be one among the professionals I’m forced change my dressing style and start wearing formals. But  the question of “Why wearing jeans to workplace is considered as unprofessional?” use in linger in my mind till today. I got the answer to my question from a discussion thread on Quora When they were invented, jeans were associated with blue-collar work. They were meant to get muddy and gross and take lots of abuse without falling apart, even if you wore the same pair every day. The people who bought them were the ones whose lives required durable clothing. And another commenter says… A professional image is critical to cementing business relationships, and part of that is, for right or wrong, how you dress. Jeans are typically associated with "kicking back", relaxation, leisure, informality,  and even a slightly rebellious flavor. The style and condition of the jeans are a consideration, as we often wear jeans into advanced states of being worn down, with tearing, etc.. that we generally do not do with other clothing items. I agree with this theory even though it may be centuries old. If you want to look like a professional and treated like a professional it’s better to be dress up in formals. These days I make a point to be in formals at workplace. Not everyone is Steve Jobs to wear a Jean & Turtle Neck T-shirt  right? CC Image credit flickr/exey

    Read the article

  • So, what&rsquo;s your blog URL?

    - by johndoucette
    Asked by many of my colleagues often enough, I decided to take the plunge and begin blogging. After many attempts to start and long discussions about what I should write about, I decided to give my “buddies” a series of lessons and tidbits to help them understand what it takes to manage a software development project in the real world. Stories of success and failure to keep hope alive. I am formally trained as a developer (BS/CS) and have scattered my code throughout the matrix since 1985 (officially working for the man). As I moved from job-to-job over my career, I have had good managers, bad ones, and ones who were – well, just sitting in the corner office. It wasn't until I began the transition and commitment to the role of project management that I began to take real software development management seriously. A boss once told me “put down the code. Start managing the people and process.” That was a scary time in my career. I loved solving really cool problems with a blank sheet of paper. It was an adrenaline rush to get an opportunity to start from scratch and write an application solution people would actually use and help them in their work/business. I felt that moving into “management” would remove me from the thrill and ownership I felt as a developer. It was a hard step to take, and one which I believe is hard for any developer. Well, I am here to help you through this transition. For those of you wanting to read my stories or learn about the tools and techniques I use on a daily basis, you too might just learn something you would have never thought of as an architect/developer. I am currently a Sr. Consultant at Magenic with the Boston branch office and primarily work with clients in the New England area. I am typically engaged as the lead project manager on our engagements, but also perform Application Lifecycle Management (ALM) assessments for development organizations as well as augment the Technical Evangelists for Microsoft and perform many Team Foundation Server (TFS) demos, installs and “get started” engagements. I have spoken at the New England Code Camp, our most recent CodeMastery event in Boston, and have written several whitepapers.   I am looking forward to helping you “Put down the code.” John Doucette

    Read the article

  • How to force a new Notification in notify-osd to show up without waiting for the earlier one to exit?

    - by Nirmik
    I have made a script(and a .desktop shortcut leading to this script) for starting and stoping xampp... It checks the status of xampp and accordingly either starts or stops xampp. Now i have assigned a notification as soon as the script is started to display "Starting xampp..." or "Stopping xampp..." and then when xampp is started or stopped,it displays "Xampp started..." or "Xampp stopped..." I've used notify-send to show notification as seen in the script below Now the thing is that here,the second notification waits for the 1st one to disappear and then pops up even if xampp has started/stopped. I want the new notification to appear immediately by forcing the earlier one to exit before the completion of its life-cycle. This can be seen to take plce when you activate/deactivate wireless/networking immediately... For example the "Wireless enabled" comes up on selecting enable wireless and if you immediately select disable wireless,the "Wireless disabled" notification comes up without waiting for "Wireless enabled" notification to complete its life-cycle. So how do i achieve this? #!/bin/sh SERVICE='proftpd' if ps ax | grep -v grep | grep $SERVICE /dev/null then notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "Stopping XAMPP..." && gksudo /opt/lampp/lampp stop && notify-send -i /opt/lampp/htdocs/xampp/img/logo- small.gif "XAMPP Stoped." else notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "Starting XAMPP..." && gksudo /opt/lampp/lampp start && notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "XAMPP Started." fi On the man page for notify-send I found --urgency=LEVEL or -u where levels are low, normal, critical. Is this of any use? making it critical? Also I tried it with the command- notify-send -u=critical"Testing" but that dint work...it gives the error- Unknown urgency criticalTesting specified. Known urgency levels: low, normal, critical. or if I give the command notify-send -u=LOW"Testing" it gives me error missing argument to -u Any relation??

    Read the article

  • Cannot get Virtualbox to install properly on Ubuntu 12.04

    - by lopac1029
    I cannot get Virtualbox to install properly on my 12.04. I first went with a manual install for the .deb from the old builds section of the Virtualbox page. That .deb opened up the Software Center and installed. Then I got the error coming up of VT-x/AMD-V hardware acceleration is not available on your system. Your 64-bit guest will fail to detect a 64-bit CPU and will not be able to boot. which I can only assume was due to my Ubuntu version being 32-bit (System Details - Overview - OC type: 32-bit, right?) So I followed these instructions to remove the .deb manually, restarted my laptop, and then FOUND the actual Virtualbox install in the Software Center and installed from that (assuming it would give me the correct version I need for my system) So after all that (and then some), I'm still getting the same error when I connect to my new job's project in Virtualbox. Can anyone point me in the right direction of what to do here? This is the first time I've ever worked with Virtualbox, and no one at this company is using Ubuntu, so I'm on my own here. EDIT: Here is the direct info from running the 2 suggested commands Inspiron-1750-brick:~ $lscpu Architecture: i686 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 2 On-line CPU(s) list: 0,1 Thread(s) per core: 1 Core(s) per socket: 2 Socket(s): 1 Vendor ID: GenuineIntel CPU family: 6 Model: 23 Stepping: 10 CPU MHz: 2100.000 BogoMIPS: 4189.45 L1d cache: 32K L1i cache: 32K L2 cache: 2048K Inspiron-1750-brick:~ $cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz stepping : 10 microcode : 0xa07 cpu MHz : 1200.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm sse4_1 xsave lahf_lm dtherm bogomips : 4189.80 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz stepping : 10 microcode : 0xa07 cpu MHz : 1200.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm sse4_1 xsave lahf_lm dtherm bogomips : 4189.45 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management:

    Read the article

  • 2010 is gone and Welcome 2011

    - by anirudha
    last days i spent my week @ firozabadthe town is much small and near to agraso i never forget to see the taj mahal and red fort their even it’s first chance to see them.i make a plan that i go to Agra last Saturday. firstly i go to red fort and i talking with many foreigner and they love to talking with me because their is only one man who with with them who is their GUIDE a person like a  book they never can talk with you but tell you about everything of the location because you buy them. their are many person come from various country such as German , Japan,  Russ , Italy and many other. their is no problem to talk with them perhaps they happen with talk to me. when i completely watch the Red fort at least i see a girl who are look like a foreigner. i talk themselves where they come from they tell me Francewhen i go elsewhere i thing to propose them to be  a friend of mine. i never propose any girl for friendship with me even in school and college. so i propose them to be a friend of mine.  they accept it i put the email ID in their hand whenever they gone. but i still not get their mail. 2ndly i go to Taj mahal the taj experience is not so good i spent 3 or 4 hours in rush. i found their is no security even their are many army force. they all person are too slow to work. they spent 10 minute to check  a person for security . their hands work very slow just like a low configuration computer. i talk many person their too. i talk to a person who tell themselves Jacob and they from Chicago. they speak very fast and i not know what they tell in speech. a another problem i got with some Chinese person. when i talking with them that i found they speak only Chinese language. Wish you a very very happy new year.

    Read the article

  • ApiChange Corporate Edition

    - by Alois Kraus
    In my inital announcement I could only cover a small subset what ApiChange can do for you. Lets look at how ApiChange can help you to fix bugs due to wrong usage of an Api within a fraction of time than it would take normally. It happens that software is tested and some bugs show up. One bug could be …. : We get way too man log messages during our test run. Now you have the task to find the most frequent messages and eliminate the Log calls from the source code. But what about the myriads other log calls? How can we check that the distribution of log calls is nearly equal across all developers? And if not how can we contact the developer to check his code? ApiChange can help you too connect these loose ends. It combines several information silos into one cohesive view. The picture below shows how it is able to fill the gaps. The public version does currently “only” parse the binaries and pdbs to give you for a –whousesmethod query the following colums: If it happens that you have Rational ClearCase (a source control system) in your development shop and an Active Directory in place then ApiChange will try to determine from the source file which was determined from the pdb the last check in user which should be present in your Active Directory. From there it is only a small hop to an LDAP query to your AD domain or the GC (Global Catalog) to get from the user name his Full name Email Phone number Department …. ApiChange will append this additional data all of your query results which contain source files if you add the –fileinfo option. As I said this is currently not enabled by default since the AD domain needs to be configured which are currently only some hard coded values in the SiteConstants.cs source file of ApiChange.Api.dll. Once you got this data you can generate metrics based on source file, developer, assembly, … and add additional data by drag and drop directly into the pivot tables inside Excel. This allows you to e.g. to generate a report which lists the source files with most log calls in descending order along with the developer name and email in the pivot table. Armed with this knowledge you can take meaningful measures e.g. to ask the developer if the huge number of log calls in this source file can be optimized. I am aware that this is a very specific scenario but it is a huge time saver when you are able to fill the missing gaps of information. ApiChange does this in an extensible way. namespace ApiChange.ExternalData {     public interface IFileInformationProvider     {         UserInfo GetInformationFromFile(string fileName);     } } It defines an interface where you can implement your custom information provider to close the gap between source control system and the real person I have to send an email to ask if his code needs a closer inspection.

    Read the article

  • Using a SQL Prompt snippet with template parameters

    - by SQLDev
    As part of my product management role I regularly attend trade shows and man the Red Gate booth in the vendor exhibition hall. Amongst other things this involves giving product demos to customers. Our latest demo involves SQL Source Control and SQL Test in a continuous integration environment. In order to demonstrate quite how easy it is to set up our tools from scratch we start the demo by creating an entirely new database to link to source control, using an individual database name for each conference attendee. In SQL Server Management Studio this can be done either by selecting New Database from the Object Explorer or by executing “CREATE DATABASE DemoDB_John” in a query window. We recently extended the demo to include SQL Test. This uses an open source SQL Server unit testing framework called tSQLt (www.tsqlt.org), which has a CLR object that requires EXTERNAL_ACCESS to be set as follows: ALTER DATABASE DemoDB_John SET TRUSTWORTHY ON This isn’t hard to do, but if you’re giving demo after demo, this two-step process soon becomes tedious. This is where SQL Prompt snippets come into their own. I can create a snippet named create_demo_db for this following: CREATE DATABASE DemoDB_John GO USE DemoDB_John GO ALTER DATABASE DemoDB_John SET TRUSTWORTHY ON Now I just have to type the first few characters of the snippet name, select the snippet from SQL Prompt’s candidate list, and execute the code. Simple! The problem is that this can only work once due to the hard-coded database name. Luckily I can leverage a nice feature in SQL Server Management Studio called Template Parameters. If I modify my snippet to be: CREATE DATABASE <DBName,, DemoDB_> GO USE <DBName,, DemoDB_> GO ALTER DATABASE <DBName,, DemoDB_> SET TRUSTWORTHY ON Once I’ve invoked the snippet, I can press Ctrl-Shift-M, which calls up the Specify Values for Template Parameters dialog, where I can type in my database name just once. Now you can click OK and run the query. Easy. Ideally I’d like for SQL Prompt to auto-invoke the Template Parameter dialog for all snippets where it detects the angled bracket syntax, but typing in the keyboard shortcut is a small price to pay for the time savings.

    Read the article

  • Ubuntu systematically losing wired connection

    - by Lukasz Baczynski
    I'm working on 11.10 for few recent days, everything was working perfect until today. Updated ubuntu (some certs were updates as far as i remember) and from this time, wired network stops working randomly and systematically. (All other pcs/macs work fine) From 192.168.0.9 icmp_seq=25 Destination Host Unreachable From 192.168.0.9 icmp_seq=26 Destination Host Unreachable From 192.168.0.9 icmp_seq=27 Destination Host Unreachable From 192.168.0.9 icmp_seq=28 Destination Host Unreachable From 192.168.0.9 icmp_seq=29 Destination Host Unreachable From 192.168.0.9 icmp_seq=30 Destination Host Unreachable From 192.168.0.9 icmp_seq=31 Destination Host Unreachable 64 bytes from 192.168.0.1: icmp_req=32 ttl=64 time=1003 ms 64 bytes from 192.168.0.1: icmp_req=33 ttl=64 time=0.496 ms 64 bytes from 192.168.0.1: icmp_req=34 ttl=64 time=0.576 ms 64 bytes from 192.168.0.1: icmp_req=35 ttl=64 time=0.522 ms 64 bytes from 192.168.0.1: icmp_req=36 ttl=64 time=0.624 ms 64 bytes from 192.168.0.1: icmp_req=37 ttl=64 time=0.625 ms 64 bytes from 192.168.0.1: icmp_req=38 ttl=64 time=0.555 ms It'll work for 20 seconds then it'll stop working for 10-30sec and so on. I've tried setting my router to give static IPs, it doesn't help. NOTHING has been changed since yesterday beside the package update... Here are other settings that may be useful: baka@baka-PC:~/Private/projects/wduk$ lspci -nnk | grep -iA2 net 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432] Kernel driver in use: r8169 baka@baka-PC:~/Private/projects/wduk$ ifconfig -a eth0 Link encap:Ethernet HWaddr **Removed MAC address** inet addr:192.168.0.9 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:fe0a:85b2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6400 errors:0 dropped:6400 overruns:0 frame:6400 TX packets:7085 errors:0 dropped:107 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4191983 (4.1 MB) TX bytes:886881 (886.8 KB) Interrupt:72 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2522 errors:0 dropped:0 overruns:0 frame:0 TX packets:2522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1070130 (1.0 MB) TX bytes:1070130 (1.0 MB) baka@baka-PC:~/Private/projects/wduk$ cat /etc/resolv.conf # Generated by NetworkManager nameserver 8.8.8.8 thanks for help

    Read the article

  • Ubuntu Server Cannot Route to the Internet

    - by ejes
    I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

    Read the article

  • I'd like to switch from 32-bit to 64-bit within same version

    - by Marty Fried
    I have a 32-bit installation of 11.10 on my 64-bit (4 GB) home AMD system. I have recently read up a bit on 64-bit version, and it seems that it would be a marginally better choice now for me. I have read about several methods to help reinstall all the various apps, using either dpkg's get-selections/set-selections and dselect in various ways, or using synaptic's save/get markings. The problem here is that I've read several variations, and I'm not sure which is best. I have enough disk space to do this with a brand new partition, so I'm not too worried about destroying anything, but I don't really want to make it my life's work, hence my appeal for expert tips. Since it's the same version, would it be safe to copy configuration files from the 32-bit system? I'd guess my home directory and /etc might be enough, and would save at least most of the time to reconfigure. But are there difference in configuration files in either of these directories for 32 vs 64 bits that might cause problems? After reinstalling to 64-bit, I can then continue along the 64 bit path for upgrades, but I thought it would be easier to switch the same version, than to try to reinstall apps and upgrade at the same time. Some methods I've seen suggested, among others: A. From Ubuntu forums On your old system (assuming it is still working), start up Synaptic and go: File->Save Markings and choose a file name along with a location (like a USB drive) that you can use when you have installed your new system). You need to check on the bottom: "Save full state, not only changes" This file contains a list of all your currently installed packages, and when you have installed and booted up your new system (and configured your repositories to the best for your location - as we all do, don't we?) then start up Synaptic and go: File-Read Markings and point it at your saved file, and after that has completed then select Apply to kick off the download & installation of all of those packages you had installed previously! B. From the same discussion: According to section 6.4.9 of the Debian Reference Manual, the following will save both the list of packages installed and their debconf configuration: # dpkg --get-selections "*" >myselections # or use \* # debconf-get-selections > debconfsel.txt and the following will reinstall and reconfigure them: # dselect update # debconf-set-selections < debconfsel.txt # dpkg --set-selections <myselections # apt-get -u dselect-upgrade # or dselect install C. A variation on the above I've seen a lot, this from stackoverflow: dpkg --get-selections > package_list then on the new install: cat package_list | sudo dpkg --set-selections && sudo apt-get dselect-upgrade I don't really understand B, or why it's slightly different than many others.

    Read the article

  • WiFi connected to router, but no internet connection

    - by Quetzacotl
    I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

    Read the article

  • Live CD has black screen HP DV6

    - by Shaun Killingbeck
    Attempting to install/try ubuntu (11.10, 12.04) on my new laptop, using a liveCD (and tried USB). I get the purple screen (with the man/keyboard at the bottom) and after that the screen flashes bright white before going black. Ubuntu continues to load in the background, with login sound etc but the screen is off. I have tried as many different solutions as I could find including: using nomodestep, xforcevesa, i915.modeset=0, and also now i915.modeset=1 in boot options (seperately): varying consequences, but either I end up at a blinking cursor with no prompt, a command line (startx fails: no screen found), or the original blank screen again Tried booting from VirtualBox - it crashes at the same place the screen would go blank when using a CD/USB tried 11.04: I don't have this problem BUT when trying to install, I get a ubi-partman error 141 (possibly down to the three partitions that came on my laptop... not sure why HP needed there own separate partition for HP Tools...) Model: HP Pavillion DV6 6B08SA Processor: AMD Quad-Core A6-3410MX APU with Radeon HD 6545G2 Dual Graphics (1.6 GHZ 4 MB L2 cache ) Chipset: AMD RS880M Any help would be greatly appreciated. I just want to be able to partition the drive and install Ubuntu. I'm assuming the issue is graphics card related, although I have no confirmation of that. Update: Tried the ?orkarounds on https://wiki.ubuntu.com/X/Troubleshooting/BlankScreen - set gfxpayload=text changed nothing, removing splash did nothing and setting vesafb.nonsense=1 did nothing either. I'd like to be able to collect some log information somehow, but I can't get to a command line from the liveCD. tried using the latest 12.04 beta, same issue tried nomodeset without splash or quiet. get the following (tail of) output before it freezes on that screen: * Starting configure network device security [OK] * Starting configure network device [OK] [ 25.720899] ieee80211 phy0: w1_ops_config: change monitor mode: false (implement) [ 25.720923] ieee80211 phy0: w1_ops_config: change power-save mode: false (implement) * Starting restore sound card(s') mixer state(s) [fail] [ 25.721849] ieee80211 phy0: w1_ops_bss_info_changed: qos enabled: false (implement) * Stopping save kernel messages [OK] * Starting bluetooth [OK] * PulseAudio configured for per-user sessions saned disabled; edit /etc/default/saned [ 25.988016] hci_cmd_timer: hci0 command tx timeout [ 26.207225] bad LUN (0:1) [ 26.223735] bad target number (1:0) [ 26.252111] bad target number (2:0) [ 26.272170] bad target number (3:0) [ 26.300154] bad target number (4:0) [ 26.328162] bad target number (5:0) [ 26.344180] bad target number (6:0) [ 26.368142] bad target number (7:0) * Checking battery state... [OK] * Stopping System V runlevel capability [OK] Does this give any indication of the problem? the false (implement) messages also reappear when I press the power button to ask it to shutdown, followed by a [fail] status for killing remaining processes.

    Read the article

  • /etc/postfix/transport missing; what should it look like?

    - by Thufir
    I'm following the mailman guide but couldn't locate /etc/postfix/ so created it as follows: root@dur:~# root@dur:~# cat /etc/postfix/transport dur.bounceme.net mailman: root@dur:~# root@dur:~# telnet localhost 25 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 dur.bounceme.net ESMTP Postfix (Ubuntu) ehlo fqdn_test 250-dur.bounceme.net 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN mail from:[email protected] 250 2.1.0 Ok rcpt to:thufir@localhost 451 4.3.0 <thufir@localhost>: Temporary lookup failure rcpt to:[email protected] 451 4.3.0 <[email protected]>: Temporary lookup failure quit 221 2.0.0 Bye Connection closed by foreign host. root@dur:~# root@dur:~# postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~# root@dur:~# tail /var/log/mail.log Aug 28 02:05:15 dur postfix/smtpd[20326]: connect from localhost[127.0.0.1] Aug 28 02:06:10 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases is unavailable. open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 02:06:10 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases lookup error for "thufir@localhost" Aug 28 02:06:10 dur postfix/smtpd[20326]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <thufir@localhost>: Temporary lookup failure; from=<[email protected]> to=<thufir@localhost> proto=ESMTP helo=<fqdn_test> Aug 28 02:06:23 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases is unavailable. open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 02:06:23 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases lookup error for "[email protected]" Aug 28 02:06:23 dur postfix/smtpd[20326]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<fqdn_test> Aug 28 02:06:28 dur postfix/smtpd[20326]: disconnect from localhost[127.0.0.1] Aug 28 02:06:49 dur dovecot: pop3-login: Login: user=<thufir>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=20338, TLS Aug 28 02:06:49 dur dovecot: pop3(thufir): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0 root@dur:~# The manual page is here.

    Read the article

  • Grub rescue - error: unknown filesystem

    - by user53817
    I have a multiboot system set up. The system has three drives. Multiboot is configured with Windows XP, Windows 7, and Ubuntu - all on the first drive. I had a lot of unpartitioned space left on the drive and was reserving it for adding other OSes and for storing files there in the future. One day I went ahead and downloaded Partition Wizard and created a logical NTFS partition from within Windows 7, still some unpartitioned space left over. Everything worked fine, until I rebooted the computer a few days later. Now I'm getting: error: unknown filesystem. grub rescue First of all I was surprised not to find any kind of help command, by trying: help, ?, man, --help, -h, bash, cmd, etc. Now I'm stuck with non-bootable system. I have started researching the issue and finding that people usually recommend to boot to a Live CD and fix the issue from there. Is there a way to fix this issue from within grub rescue without the need for Live CD? UPDATE By following the steps from persist commands typed to grub rescue, I was able to boot to initramfs prompt. But not anywhere further than that. So far from reading the manual on grub rescue, I was able to see my drives and partitions using ls command. For the first hard drive I see the following: (hd0) (hd0,msdos6) (hd0,msdos5) (hd0,msdos2) (hd0,msdos1) I now know that (hd0,msdos6) contains Linux on it, since ls (hd0,msdos6)/ lists directories. Others will give "error: unknown filesystem." UPDATE 2 After the following commands I am now getting to the boot menu and can boot into Windows 7 and Ubuntu, but upon reboot I have to repeat these steps. ls ls (hd0,msdos6)/ set root=(hd0,msdos6) ls / set prefix=(hd0,msdos6)/boot/grub insmod /boot/grub/linux.mod normal UPDATE 3 Thanks Shashank Singh, with your instructions I have simplified my steps to the following. I have learned from you that I can replace msdos6 with just a 6 and that I can just do insmod normal instead of insmod /boot/grub/linux.mod. Now I just need to figure out how to save this settings from within grub itself, without booting into any OS. set root=(hd0,6) set prefix=(hd0,6)/boot/grub insmod normal normal UPDATE 4 Well, it seems like it is a requirement to boot into Linux. After booting into Ubuntu I have performed the following steps described in the manual: sudo update-grub udo grub-install /dev/sda This did not resolve the issue. I still get the grub rescue prompt. What do I need to do to permanently fix it? I have also learned that drive numbers as in hd0 need to be translated to drive letters as in /dev/sda for some commands. hd1 would be sdb, hd2 would be sdc, and so on. Partitions listed in grub as (hd0,msdos6) would be translated to /dev/sda6.

    Read the article

  • The only metric with any value

    - by Malcolm Anderson
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} There's a lot of talk in the Scrum world about metrics. What's the velocity? How big is a story point?  How many story points is that team producing per man hour?   People are sadly missing the whole point.  Take your measurements up a level or two.  When you get down to it, the only metric that makes any difference, is ROI.   The problem is that often times, the developers work in a dark hole, far removed from the realities of how exactly they get paid.  A bigger problem is that mid-level managers tend to be further removed from the realities of ROI.  A lot of times mid-level managers get tasked with tracking their teams "productivity" using things like, "lines of code", or "completeness of the productivity reports."   Monetize your projects and then track your velocity against business value (real dollars).    When your development teams can say, "Last year, our team cost the business 2 million dollars and we know that because of our efforts, the company saved 2 million dollars in waste and increased revenues by another 4 million dollars." At that point you have just moved your development team from a cost center, to a profit center.  You might have to give them a raise, but they have demonstrated that they have earned it.

    Read the article

  • Memories about Tadeusz Golonka

    - by Damian
    Today at 10:55 AM, Tadeusz Golonka - my greatest  Mentor and Teacher  passed away. I had te opportunity to met Tadek in person several times last years. It was always a great experience to see how he shared his energy and passion. I was always impressed and had a lot of new ideas after such meeting or lecture. I can remember the meeting  in early 2009 and his briliant speech he did for us, the MVP community in Poland. We spent two days together and he talked to us all the time. He gave us examples how to share IT passion to other people and how to be better person for others. He was the greates Mentor I have ever met - I realized this during that meeting. My greates dream was and still is to be "like Tadek". Many Times I just went to events to see / hear him on stage ("in action"). I always wanted to have his energy, empathy and passion. Now I have to live without his good words and advices....Let me put here the words that Adam Cogan wrote on Tadek's profile on Facebook. I just can't write about that fatal accident. "The circumstances of Tadeusz Golonka death are too tragic. Tad stood up to offer his seat to an elderly lady, he lost his balance and then he slipped and hit the tram door hard. He then fell out of the tram and hit the metal barriers that separate the tram rails from the street. It was a severe accident...... So horrible.  At first it was a miracle is that he survived... he fought for several days.  My thoughts are with his lovely family. The family have asked for blood donations as a symbolic gift. Tad received a lot of blood.  Thank you Tad, you were a wonderful person. I will remember you as a kind man, a gentleman. "RIP Tadeusz- You will never ever be forgotten. You are with us all the time  

    Read the article

  • Am I deluding myself? Business analyst transition to programmer

    - by Ryan
    Current job: Working as the lead business analyst for a Big 4 firm, leading a team of developers and testers working on a large scale re-platforming project (4 onshore dev, 4 offshore devs, several onshore/offshore testers). Also work in a similar capacity on other smaller scale projects. Extent of my role: Gathering/writing out requirements, creating functional specifications, designing the UI (basically mapping out all front-end aspects of the system), working closely with devs to communicate/clarify requirements and come up with solutions when we hit roadblocks, writing test cases (and doing much of the testing), working with senior management and key stakeholders, managing beta testers, creating user guides and leading training sessions, providing key technical support. I also write quite a few macros in Excel using VBA (several of my macros are now used across the entire firm, so there are maybe around 1000 people using them) and use SQL on a daily basis, both on the SQL compact files the program relies on, our SQL Server data and any Access databases I create. The developers feel that I am quite good in this role because I understand a lot about programming, inherent system limitations, structure of the databases, etc so it's easier for me to communicate ideas and come up with suggestions when we face problems. What really interests me is developing software. I do a fair amount of programming in VBA and have been wanting to learn C# for awhile (the dev team uses C# - I review code occasionally for my own sake but have not had any practical experience using it). I'm interested in not just the business process but also the technical side of things, so the traditional BA role doesn't really whet my appetite for the kind of stuff I want to do. Right now I have a few small projects that managers have given me and I'm finding new ways to do them (like building custom Access applications), so there's a bit here and there to keep me interested. My question is this: what I would like to do is create custom Excel or Access applications for small businesses as a freelance business (working as a one-man shop; maybe having an occasional contractor depending on a project's complexity). This would obviously start out as a part-time venture while I have a day job, but eventually become a full-time job. Am I deluding myself to thinking I can go from BA/part-time VBA programmer to making a full-time go of a freelance business (where I would be starting out just writing custom Excel/Access apps in VBA)? Or is this type of thing not usually attempted until someone gains years of full-time programming experience? And is there even a market for these types of applications amongst small businesses (and maybe medium-sized) businesses?

    Read the article

  • MatheMagics - Guess My Age Method 1

    - by PointsToShare
    © 2011 By: Dov Trietsch. All rights reserved MatheMagic – Guess My Age – Method 1 The Mathemagician stands on the stage and asks an adult to do the following: ·         Do the next few steps on your calculator, or the calculator in your phone, or even on a piece of paper. ·         Do it silently! Don’t tell me the results until I ask for them directly ·         Compute a single digit multiple of 9 – any one of 9, 18, 27, … all the way to 81, will do. ·         Now multiply your age by 10 ·         Subtract the 9 multiple from this number. ·         Tell me the result. Notice that I don’t know which multiple of 9 you subtracted from 10 times your age. I will nonetheless immediately tell you what your age is. How do I do this? Let’s do the algebra. 10X – 9Y = 10X – 10Y + Y = 10(X – Y) + Y Now remember, you asked an adult, so his/her age is a two digit number (maybe even 3 digits), thus reducing it by the single digit multiplied by nine is still positive – the lowest is can be is 100 – 81 which yields 19. Now make two numbers out of the result. The last digit and the number before it. This number is X – Y or the age minus the single digit you selected. The last digit is this very single digit. This is always so regardless of the digit you selected. So… Add tis digit to the other number and you get back the age! Q.E.D Example: I am 76 years old and here is what happens when I do the steps 76 x 10 = 760 760 – 18 = 742 made of 74 and 2. My age is 74 + 2 760 – 81 = 679 made of 67 and 9. My age is 67 + 9 A note to the socially aware mathemagician – it is safer to do it with a man. The chances of a veracious answer are much, much higher! The trick may be accomplished on any 2 or 3 digit number, not just one’s age, but if you want to know your date’s age, it’s a good way to elicit it. That’s All Folks PS for more Ageless “Age” mathemagics go to www.mgsltns.com/games.htm and also here: http://geekswithblogs.net/PointsToShare/archive/2011/11/15/mathemagics---guess-my-age---method-2.aspx

    Read the article

  • Building a Solaris 11 repository without network connection

    - by user12611852
    Solaris 11 has been released and is a fantastic new iteration of Oracle's rock solid, enterprise operating system.  One of the great new features is the repository based Image Packaging system.  IPS not only introduces new cloud based package installation services, it is also integrated with our zones, boot environment and ZFS file systems to provide a safe, easy and fast way to perform system updates. My customers typically don't have network access and, in fact, can't connect to any network until they have "Authority to connect."  It's useful, however, to build up a Solaris 11 system with additional software using the new Image Packaging System and locally stored repository. The Solaris 11 documentation describes how to create a locally stored repository with full explanations of what the commands do. I'm simply providing the quick and dirty steps.  The easiest way is to download the ISO image, burn to a DVD and insert into your DVD drive.  Then as root: pkg set-publisher -G '*' -g file:///cdrom/sol11repo_full/repo solaris Now you can to install software using the GUI package manager or the pkg commands.  If you would like something more permanent (or don't have a DVD drive), however, it takes a little more work. After installing Solaris 11, download (on another system perhaps) the two files that make up the Solaris 11 repository from our download site Sneaker-net the files to your Solaris 11 system Unzip and cat the two files together to create one large ISO image. The file is about 6.9 GB in size zfs create rpool/export/repoSolaris11 zfs set atime=off rpool/export/repoSolaris11 zfs set compression=on rpool/export/repoSolaris11 (save some space) lofiadm -a sol-11-1111-repo-full.iso /dev/lofi/1 mount -F hsfs /dev/lofi/1 /mnt You could stop here and set the publisher to point to the /mnt/repo location, however, this mount will not be persistent across reboots. Copy the repository from the mounted ISO image to a permanent, on disk location. rsync -aP /mnt/repo /export/repoSolaris11 pkgrepo -s /export/repoSolaris11 refresh pkg set-publisher -G '*' -g /export/repoSolaris11/repo solaris You now have a locally installed repository for adding additional software packages for Solaris 11.  The documentation also takes you through publishing your repository on the network so that others can access it.

    Read the article

  • What kind of position matches my skills, experience and interests? [closed]

    - by Ryan
    I work in a large firm and my current job covers a variety of different duties. Due to several factors I am seriously considering finding a new job (hours, pay-cut, limited career growth). I have worked for the company nearly 4 years and almost 2 years ago I transitioned into more of a business analyst role (previously I was working in a client facing role for our audit group). In this role I have overseen all aspects of the development of a large scale re-platforming of our firm's key tool in analyzing investment portfolios. I gathered requirements, wrote specs, designed the UI and functionality, worked closely with developers (onshore and offshore) to see to it the implementation was correct, managed schedules and was the lead tester. This is a large scale system used by thousands of people around the world. I've also written Excel macros, reports in SQL, given trainings, written technical manuals, interfaced with senior managers and partners, etc. I've been on a couple interviews sporadically, most of which were for positions aimed at higher management consulting type positions, dealing with strategy, overall process management, project management, etc. What really interests me is the technical stuff and overseeing a project from beginning to end (although I would rather not have to do so many of the tasks on my own). I genuinely like a lot of what I do, but the company culture and attitude towards overworking people combined with my recent pay-cut (my overtime was cut due to a promotion to a higher level) has lead me to want to seek work elsewhere. The problem is - what type of work could I realistically do? I feel like traditional business analysis is too much business and not enough tech stuff, and I've really taken a shine lately to beefing up my programming abilities and creating small programs to automate things around work. I also feel that because my actual years of experience as a business analyst (figure 1.5 years realistically) puts me at a junior level doing a lot of grunt requirements gathering, when the work that I have been doing with my current company is more in line with what a Program Manager does (depending on your definition I guess). So in reality, when I'm job hunting I get a bit perplexed because I feel like the traditional BA stuff wouldn't really suit me, and even if it did it's usually something along the lines of 5-10 years experience for the type of work that is similar to what I've done (and I've also found most BA jobs to be contract only which at the moment I'm not too keen on). Program Manager is something that interests me, but again I feel like the experience is lacking because that's a much more senior position. Am I in some kind of career no-man's land? Any idea what would best suit me given my experience and abilities, as well as my interests? I plan to keep learning programming on the side, but don't expect to get a job being a straight programmer given my relative inexperience with programming.

    Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >