Search Results

Search found 34495 results on 1380 pages for 'network and internet'.

Page 119/1380 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >

  • Network switching issues with MacOS 10.7?

    - by Denis
    I'm having a wired problem and hope somebody can tip me, what way should I dig to. I'm using MacBookPro with Lion 10.7.3 both at my working place & at home. At working place, we have a domain-based network with 802.1x authorization (more than 400 computers) and to connect it I'm using Ethernet cable. IP range is 10.10.2.*. All network settings are setup automatically by DHCP. Also, in settings, I have Network Account Server setup in the User&Groups Settings for my work Domain server - and it is available only from corporate network. At home, I have an ADSL router, that shares Internet connection by WiFi in NAT mode. I'm using WiFi to connect it. Router gives out addresses from 192.168.1.* range and all settings are also set up by router's DHCP. So, my problem is the following. When I come back home from the office, I open my MacBook and AirPort automatically connects my WiFi network. After this, for about 1 minute I'm able to browse sites & ping hosts successfully. But after this minute, network connection is broken down. All pings return time-out. trace route to google.com stops on 192.168.1.1 (which is my router). This lasts for 3-4 minutes. After that network connection is automatically repaired and all pings go smoothly again. At the same time, when my MacBook return timeouts, I can successfully ping any host from my wife's MacBook - so this doesn't look like router issue. When I come to the office, I don't have any issues and Internet connection is available & stable moments after ethernet cable plugged in. Do anybody has any clues about this? What should I monitor & what settings look for resolving this issue? Please, ask, what additional information should I provide. Hoping for good advice & thanks in advance!

    Read the article

  • tc rules block traffic from some hosts at network

    - by user139430
    I have a problem I can not solve. The script, which sets the rules for traffic shaping is blocking the traffic from some hosts.If I remove all the rules, then it works. I can not understand why? Here is my script... #!/bin/sh cmdTC=/sbin/tc rateLANDl="60mbit" ceilLANDl="60mbit" rateLANUl="40mbit" ceilLANUl="40mbit" quantLAN="1514" # Nowaday bandwidth limit set to 100mbit. # We devide it with 60mbit download and 40mbit upload bandthes. rateHiDl="30mbit" ceilHiDl="60mbit" rateHiUl="20mbit" ceilHiUl="40mbit" quantHi="1514" rateLoDl="30mbit" ceilLoDl="60mbit" rateLoUl="20mbit" ceilLoUl="40mbit" quantLo="1514" devNIF=eth0 devFIF=ifb0 modprobe ifb ip link set $devFIF up 2>/dev/null #exit 0 ################################################################################################ # Remove discuiplines from network and fake interfaces ################################################################################################ $cmdTC qdisc del dev $devNIF root 2>/dev/null $cmdTC qdisc del dev $devFIF root 2>/dev/null $cmdTC qdisc del dev $devNIF ingress 2>/dev/null if [ "$1" = "down" ]; then exit 0 fi ################################################################################################ # Create discuiplines for network interface ################################################################################################ $cmdTC qdisc add dev $devNIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devNIF parent 1:0 classid 1:1 htb rate ${rateLANDl} ceil ${ceilLANDl} quantum ${quantLAN} $cmdTC class add dev $devNIF parent 1:1 classid 1:11 htb rate ${rateHiDl} ceil ${ceilHiDl} quantum ${quantHi} $cmdTC class add dev $devNIF parent 1:1 classid 1:12 htb rate ${rateLoDl} ceil ${ceilLoDl} quantum ${quantLo} $cmdTC qdisc add dev $devNIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devNIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devNIF protocol all parent 1:0 u32 match ip dst 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devNIF protocol all parent 111: handle 111 flow hash keys dst divisor 1024 baseclass 1:11 $cmdTC filter add dev $devNIF protocol all parent 112: handle 112 flow hash keys dst divisor 1024 baseclass 1:12 ################################################################################################ # Create discuiplines for fake interface ################################################################################################ $cmdTC qdisc add dev $devFIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devFIF parent 1:0 classid 1:1 htb rate ${rateLANUl} ceil ${ceilLANUl} quantum ${quantLAN} $cmdTC class add dev $devFIF parent 1:1 classid 1:11 htb rate ${rateHiUl} ceil ${ceilHiUl} quantum ${quantHi} $cmdTC class add dev $devFIF parent 1:1 classid 1:12 htb rate ${rateLoUl} ceil ${ceilLoUl} quantum ${quantLo} $cmdTC qdisc add dev $devFIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devFIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devFIF protocol all parent 1:0 u32 match ip src 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devFIF protocol all parent 111: handle 111 flow hash keys src divisor 1024 baseclass 1:11 $cmdTC filter add dev $devFIF protocol all parent 112: handle 112 flow hash keys src divisor 1024 baseclass 1:12 ################################################################################################ # Create redirect discuiplines from network to fake interface ################################################################################################ $cmdTC qdisc add dev $devNIF handle ffff:0 ingress $cmdTC filter add dev $devNIF parent ffff:0 protocol all u32 match u32 0 0 action mirred egress redirect dev $devFIF Here is my /etc/modules: loop ifb ppp_mppe nf_conntrack_pptp nt_conntrack_proto_gre nf_nat_pptp nf_nat_proto_gre The system is Linux wall 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux

    Read the article

  • Week 21: FY10 in the Rear View Mirror

    - by sandra.haan
    FY10 is coming to a close and before we dive into FY11 we thought we would take a walk down memory lane and reminisce on some of our favorite Oracle PartnerNetwork activities. June 2009 brought One Red Network to partners offering access to the same virtual kickoff environment used by Oracle employees. It was a new way to deliver valuable content to key stakeholders (and without the 100+ degree temperatures). Speaking of hot, Oracle also announced in June new licensing options for our ISV partners. This model enables an even broader community of ISVs to build, deploy and manage SaaS applications on the same platform. While some people took the summer off, the OPN Program team was working away to deliver a brand new partner program - Oracle PartnerNetwork Specialized - at Oracle OpenWorld in October. Specialized. Recognized. Preferred. If you haven't gotten the message yet, we may need an emergency crew to pull you out from that rock you've been hiding under. But seriously, the announcement at the OPN Forum drew a big crowd and our FY11 event is shaping up to be just as exciting. OPN Specialized was announced in October and opened our doors for enrollment in December 2009. To mark our grand opening we held our first ever social webcast allowing partners from around the world to interact with us live throughout the day. We had a lot of great conversations and really enjoyed the chance to speak with so many of you. After a short holiday break we were back at it - just a small announcement - Oracle's acquisition of Sun. In case you missed it, here is a short field report from Ted Bereswill, SVP North America Alliances & Channels on the partner events to support the announcement: And while we're announcing things - did we mention that both Ted Bereswill and Judson Althoff were named Channel Chiefs by CRN? Not only do we have a couple of Channel Chiefs, but Oracle also won the Partner Program 5 Star Programs Award and took top honors at the CRN Channel Champion Awards for Financial Factors/Financial Performance in the category of Data and Information Management and the and Xchange Solution Provider event in March 2010. We actually caught up with Judson at this event for a quick recap of our participation: But awards aside, let's not forget our main focus in FY10 and that is Specialization. In April we announced that we had over 35 Specializations available for partners and a plan to deliver even more in FY11. We are just days away from the end of FY10 but hope you enjoyed our walk down memory lane. We are already planning lots of activity for our partners in FY11 starting with our Partner Kickoff event on June 29th. Join us to hear the vision and strategy for FY11 and interact with regional A&C leaders. We look forward to talking with you then. The OPN Communications Team

    Read the article

  • How to Use Your Android Phone as a Modem; No Rooting Required

    - by Jason Fitzpatrick
    If your cellular provider’s mobile hotspot/tethering plans are too pricey, skip them and tether your phone to your computer without inflating your monthly bill. Read on to see how you can score free mobile internet. We recently received a letter from a How-To Geek reader, requesting help linking their Android phone to their laptop to avoid the highway robbery their cellular provider was insisting upon: Dear How-To Geek, I recently found out that my cellphone company charges $30 a month to use your smartphone as a data modem. That’s an outrageous price when I already pay an extra $15 a month charge just because they insist that because I have a smartphone I need a data plan because I’ll be using so much more data than other users. They expect me to pay what amounts to a $45 a month premium just to do some occasional surfing and email checking from the comfort of my laptop instead of the much smaller smartphone screen! Surely there is a work around? I’m running Windows 7 on my laptop and I have an Android phone running Android OS 2.2. Help! Sincerely, No Double Dipping! Well Double Dipping, this is a sentiment we can strongly related to as many of us on staff are in a similar situation. It’s absurd that so many companies charge you to use the data connection on the phone you’re already paying for. There is no difference in bandwidth usage if you stream Pandora to your phone or to your laptop, for example. Fortunately we have a solution for you. It’s not free-as-in-beer but it only costs $16 which, over the first year of use alone, will save you $344. Let’s get started! Latest Features How-To Geek ETC What Can Super Mario Teach Us About Graphics Technology? Windows 7 Service Pack 1 is Released: But Should You Install It? How To Make Hundreds of Complex Photo Edits in Seconds With Photoshop Actions How to Enable User-Specific Wireless Networks in Windows 7 How to Use Google Chrome as Your Default PDF Reader (the Easy Way) How To Remove People and Objects From Photographs In Photoshop Make Efficient Use of Tab Bar Space by Customizing Tab Width in Firefox See the Geeky Work Done Behind the Scenes to Add Sounds to Movies [Video] Use a Crayon to Enhance Engraved Lettering on Electronics Adult Swim Brings Their Programming Lineup to iOS Devices Feel the Chill of the South Atlantic with the Antarctica Theme for Windows 7 Seas0nPass Now Offers Untethered Apple TV Jailbreaking

    Read the article

  • PPTP VPN connects via NM but goes down during SSH connection

    - by Andrea Olivato
    I setup a VPN PPTP connection via network manager and it connects correctly (I see the lock near the notification icon and the message "Vpn connection has been successfully...") As soon as I try to perform any SSH connection via the established tunnel the connection itself goes down with the message "Vpn connection failed". the SSH connection always fails at debug1: SSH2_MSG_KEXINIT sent I've looked into the system logs and this is the log Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> Starting VPN service 'pptp'... Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 7093 Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' appeared; activating connections Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: init (1) Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: starting (3) Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (Connect) reply received. Dec 12 12:25:05 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (IP4 Config Get) reply received from old-style plugin. Dec 12 12:25:05 ushuaia NetworkManager[1155]: <info> VPN Gateway: 5.98.141.210 Dec 12 12:25:06 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (IP Config Get) complete. Dec 12 12:25:06 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: started (4) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: stopping (5) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: stopped (6) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state change reason: 0 Dec 12 12:25:15 ushuaia NetworkManager[1155]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Dec 12 12:25:20 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' disappeared Please note that the same vpn is configured on my colleagues Windows 7 and works without problem when they use putty to connect via SSH

    Read the article

  • Problem getting GOBI 2000 HS to work

    - by Zypher
    I've been trying to get my integrated GOBI WWAN card to work under 10.10 for a while now. I was able to get the network manager to see the card after installing the gobi-loader package. I was able to setup the connection, but i cannot establish a connection to Verizon. Below is the output from /var/log/daemon.log as i try to connect. Oct 19 14:29:42 gbeech-x201 AptDaemon: INFO: Quiting due to inactivity Oct 19 14:29:42 gbeech-x201 AptDaemon: INFO: Shutdown was requested Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) starting connection 'Verizon connection' Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 3 -> 4 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 4 -> 6 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete. Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 6 -> 4 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <warn> CDMA connection failed: (32) No service Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 4 -> 9 (reason 0) Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Marking connection 'Verizon connection' invalid. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <warn> Activation (ttyUSB0) failed. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 9 -> 3 (reason 0) Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): deactivating device (reason: 0). Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Policy set 'Auto SO-GUEST' (wlan0) as default for IPv4 routing and DNS. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Policy set 'Auto SO-GUEST' (wlan0) as default for IPv4 routing and DNS.

    Read the article

  • WiFi on Ubuntu 12.04 custom: downloading unbearably slow

    - by Mark
    iwconfig reports 11 Mbps, yet I've seen as low as <1 KBps. This is the latest in my laundry list of Ubuntu problems in a dual-boot machine (cyberpowerpc custom, intel i7-3820, nvidia gtx 570). I received it two days ago, Windows 7 running fine, still having problems with Ubuntu. The browsing is intermittent but unacceptable. e.g. I could get to this site last night but I couldn't post this question. The downloading is unbearably slow, I can't download anything or install any packages because the speed is so slow. e.g. I am trying to install vim which is inexplicably missing from my 12.04 install (add another one to the problems list) and my download speed reported in the terminal was 241 B/s. Yes, bytes. iwconfig reports 11 Mbps, which further adds to the confusion. User@ubuntu:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:39:76:2C:A1 Bit Rate=11 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:54 Invalid misc:18 Missed beacon:0 eth0 no wireless extensions. Any ideas? I see this is a problem a lot of people, but none of the on line solutions have worked for me so far. e.g. one site recommends editing the ath9k.conf file in /etc/modprobe.d, yet this file isn't even in the folder: User@ubuntu:/$ cd etc/modprobe.d User@ubuntu:/etc/modprobe.d$ ls alsa-base.conf blacklist-oss.conf blacklist-ath_pci.conf blacklist-rare-network.conf blacklist.conf blacklist-watchdog.conf blacklist-firewire.conf dkms.conf blacklist-framebuffer.conf nvidia-current_hybrid.conf blacklist-modem.conf nvidia-graphics-drivers.conf I think the nvidia gpu might be mucking things up. I had the "blinking cursor" problem when installing in the first place, and then I had the monitor out of range problem as well. I have my faithful Asus laptop, which is running Ubuntu 12.04 just fine. The only difference is executing host -t SOA local in the terminal gives User@ubuntu:~$ host -t SOA local local has SOA record local. nobody.localhost. 42 86400 43200 604800 10800 in my new machine, and the command reports Host local. not found in the laptop. Help would be most welcome, as I am in danger of reverting back to Windows. I'm seriously considering it. Sorry for the length, trying to show my effort in resolving the issue and include terminal snippets that might be helpful.

    Read the article

  • XAMPP - allow internet connection

    - by user1645034
    I usually do my web dev on a production server, now i need to bring some work at home. I have installed XAMPP on my laptop and it seems to work perfectly fine. Most of my project involves CURL enabled, I need to make my xampp application to access the internet. Perhaps give it some IP address and Gateway. I've seen documentation how to enable CURL on xampp, yet I'm struggling to find how to make XAMPP to have internet access. I'm not asking how to access my XAMPP remotely, I'm simply asking how to give internet connection to xampp application for my CURL and other social network API to work.

    Read the article

  • Connecting desktop computer to the internet through laptop wifi

    - by Josh
    Due to some home network complications I have had to move my router to a seperate part of the house, therefore the wired network I had set up can no longer work. Before I find the time to go out and buy a Wifi adapter for my desktop PC, I have a laptop that uses a built in Wifi card to connect to my router and this can connect to the internet, and I was wondering if I could somehow access the internet on my desktop PC via my laptop. I'm hoping for a not-so-complex solution as this will only be set up for a few days, but it is quite vital that my desktop computer gets internet access. Does anyone have experience in this sort of thing and can help me out? Thanks.

    Read the article

  • Always a path to the internet even in Windows SBS is off

    - by Mark
    Hello all, is it possible to have a configuration in a Windows 2003 SBS environment where in the event that the SBS box crashed/turned off/ or is being worked on that there can still exist a path to the internet for domain users and visitors to still use? I would like to have the standalone router issue DHCP IPs. The primary DNS would point to the SBS, the secondary wouuld point to the ISP DNS Server. My theory was that if someone was using the internet and the SBS box went down they wouldn't be able to access the network shares but still be able to use the internet. (We are moving everything into the clouds with Google Apps Non-Profit) Does this seem like a reasonable configuration? Or are they're pitfalls that I will fall into? Thanks Mark

    Read the article

  • Two Router issue, cannot reach internet

    - by DeBuGGeR
    I have on ADSL router and one CISCO Wifi Router. The ADSL Router is working fine on its own. I am connecting the lan port of the ADSL Router to the internet(RJ45) port of my Cisco wifi router. But I cannot access the internet from the Cisco router, neither through wifi nor through ethernet connection. The IP of ADSL router is 192.168.1.1 and the ip of my Wifi router is 192.168.1.100. Should I connect to the LAN port of my Wifi router rather than using the ethernet port(Marked as Internet)?

    Read the article

  • Acer Aspire 7739G-6647 won't connect to the internet

    - by Nux
    Acer Aspire 7739G-6647, it belongs to a family member. I reinstalled the chipset, LAN drivers, ethernet controllers, etc. I'm positive it's not my router or modem or anything like that. I have other laptops running on the network, this one just has some strange issue. For some reason, it's saying "Work Offline" is enabled when I open Windows Media Player, and the PC seems to be connected to the network, but on the graphic in networking, it doesn't show the connection between the network and the internet. Could anyone try to state any possible reason for this issue? Any help is appreciated.

    Read the article

  • Two NIC cards with the same metric - Internet traffic going out the wrong one

    - by bvanderw
    I have two NIC cards in my computer - one is connected to our corporate network and the Internet, the other is connected to a private LAN through a Linksys WRT54G. Both cards use DHCP. This was never an issue with Windows XP, but with Windows Vista (and Windows 7) the metric for the 0.0.0.0 route is the same (20), and it appears that some network traffic that should go out my main network card are going out my secondary card instead. The solution to date is to delete the 0.0.0.0 route associated with the second NIC card, but I have to do this several times a day. Is there a better solution? --Bruce

    Read the article

  • Blocking internet poker applications

    - by Matthew Savage
    I 'look after' the wireless internet for a cafe where I live, and we've noticed that there's quite a substantial slow down of internet speeds when certain users are playing internet poker. I've put in filters to block any HTTP traffic referencing gambling and poker etc, however I want to be able to block any applications (i.e. poker clients) which don't use HTTP. I've tried searching around for a list of poker clients and perhaps their ports, but have had no real luck. Does anyone know what these might be?

    Read the article

  • Apache w/out internet connection

    - by robert knobulous
    I have a Vista laptop that I have been running Apache / MySql / Php / PhpMyAdmin on for quite some time without fail. I just use it to test bits of code here and there etc. No problems, until recently when I needed to test something and I happened to be in a place that I could not get an internet connection. Why am I unable to access localhost from the same machine without an internet connection? I am type http://localhost..etc into the browser's address bar and I get the message that I am unable to access without an internet connection. I checked my windows/system32/etc/hosts file and the first two lines are 127.0.0.1 localhost ::1 localhost What am I missing here?

    Read the article

  • mystery Internet traffic to port 445

    - by Ben Collver
    Recently, I noticed traffic from the office network to TCP port 445 on the Internet [a]. Below are the Linux firewall log entries to Facebook's network [b] and Google's network [c]. I would like to identify the source of this traffic. My first guess is that Facebook and Google might be using multiple TCP ports for SSL load balancing. However, I could not confirm this based on the web proxy logs. What else might it be? [a] http://support.microsoft.com/kb/204279 [b] Sep 4 08:30:03 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.131 DST=69.171.237.34 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=14287 DF PROTO=TCP SPT=51711 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0 [c] Aug 28 06:02:41 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.115 DST=173.194.33.47 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=4558 DF PROTO=TCP SPT=49294 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0

    Read the article

  • Two VPN (internet) connections rounting (win2003)

    - by tmp3128
    Here is my setup: - win2003 server (ISA installed) with 3 NICs:   1) internal network   2) ISP 1 (default) network (DHCP enabled)   3) ISP 2 (backup) network (DHCP enabled) - several "normal" PC within internal net - one "special" PC within internal net Both ISP 1 and ISP 2 provide access to internet and their resources thru their VPN connections. The goal is to enable all "normal" PCs to use internet from ISP_1's VPN connection and "special" should use only ISP_2's VPN connection. Futhermore all "normal" and "special" PCs should have access to several servers accesible only thru ISP_2's VPN connection. I have some thoughts how to achieve this but I want to be certain because everything should be configured as quickly as posible, avoiding significant downtime. windows-server-2003 isa routing vpn

    Read the article

  • Not able to connect to internet in RHEL 5

    - by chankey007
    I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

    Read the article

  • Not able to connect to internet in RHEL 5

    - by chankey007
    I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

    Read the article

  • Provisioning SIP Phones over the internet

    - by Jorge Fernandez
    I have a few SIP Phones that are located of site and connect to my PBX over the internet to make calls. For some reason one of these phones has become unprovisioned. In my office phones get provisioned by the server via TFTP. The ones that I have off site I pre-provisioned manually before I sent them off-site (I'm in Florida the phone is in New Jersey). Whats the best way to provision these over the internet? TFTP is very insecure. Sending the plain text profiles with the SIP Account and Password over the internet is out of the question. The phones have been off-site for about 6 months without any issues. Im using Trixbox and Cisco 7940 Phones.

    Read the article

  • Windows 7 wifi reports "no network access" and "no internet access" but connects in fedora

    - by rick2047
    I am running windows 7 home basic (64bit) on a Acer 5742G laptop with Atheos wifi adapter in it. Yesterday, I hiberneted my computer as I always do and up untill then the wifi was working fine. When I booted my computer up again today I started having a strange problem: It detects my wifi but after connecting to it, it keeps on oscillating between states of no network access and no internet access. I can't connect to anything (the internet or my router). I tried to reset my internet protocol stack using this fixit file. I also tried to uninstall and reinstall my network driver. Neither helped. I am using the same laptop's fedora installation right now and the wifi is working perfectly fine. Please help. Edit To add additional details, I have Microsoft Security essentials as my antivirus software and I haven't messed with the firewall or the router configurations.

    Read the article

  • Windows VPN - NO internet access

    - by sharru
    I host a network of servers behind a Fortigate 200a firewall in the DC. I connect to those servers via a VPN connection. The problem is that when i connect to the VPN, I lose my internet connection on the local PC (windows 7). I would like to be connected to the VPN and still surf the web. i guess this means to only forward a range of ip to the VPN connection. I've read other answers on serverfault, talking about "un-check the 'Use default gateway on remote network' option in your Windows 7 PPTP network connection settings". When i do that , i get internet access but no access to the servers in the VPN. Any idea how to get both working? Should i change something on the fortigate 200a config? Do i need two networks cards? Is there a place in windows to define ip range for the vpn connection?

    Read the article

  • Time randomly changing itself, internet randomly dying

    - by Vee
    Operating System MS Windows 8 Enterprise 64-bit CPU Intel Core i7 2700K @ 3.50GHz 45 °C Sandy Bridge 32nm Technology RAM 8,00 GB Dual-Channel DDR3 @ 800MHz (8-8-8-24) Motherboard ASRock Z77 Extreme4-M (CPUSocket) 40 °C Graphics SMXL2270HD (1920x1080@60Hz) M2094D-PZ (1680x1050@60Hz) 896MB GeForce GTX 275 (CardExpert Technology) 57 °C Hard Drives 466GB FUJITSU MAXTOR STM3500320AS (SATA) 39 °C Optical Drives ASUS DRW-2014L1T Audio High Definition Audio Device Hello everyone, I installed Windows 8 RTM a few weeks ago. It's not my first time installing it, but it's the first time having two annoying problems: 1) Randomly, the system clock changes time all by itself - to fix it I have to open the time window and sync it with the internet. 2) Randomly, internet connection stops working - to fix I have to run troubleshooting. Windows will find a problem with IP on the "Ethernet" connection and fix it. 3) In rare occasions, my PC freezes and I need to restart it (a BSOD once happened, but after that only freezes) How can I permanently solve these problems? This is what I've already tried: Reset Virus scan Stop/reset the Windows Time service Disable/re-enable Windows Time automatic internet sync Change time from BIOS Change motherboard battery

    Read the article

  • ubuntu server in a vm, can't connect to internet

    - by jessh
    I'm attemtping to host my own development web server in a virtual box guest, Ubuntu Server. I would like this virtual machine to be accessible from not only my home network, but outside the LAN as well. As such, I've set up a static IP (so I can later forward ports to this static IP.) My virtual box settings have this vm only using one adapter -- in bridged mode. Here's what my /etc/network/interfaces looks like: iface eth0 inet static address 10.0.1.203 /*this is outside the DHCP range*/ netmask 255.255.255.0 gateway 10.0.1.1 network 10.0.1.0 broadcast 10.0.1.255 dns-nameservers: 8.8.8.8 8.8.8.4 Here's what the output of ifconfig looks like: https://dl.dropbox.com/u/2241201/locker/ubuntu.png My Host is a mac mini, running OS X 10.7. From within the guest, if I ping google.com: $ ping google.com # outputs 'ping: unknown host google.com' immediately Why am I unable to access the web?

    Read the article

  • Connecting desktop computer to the internet through laptop wifi

    - by Josh
    Due to some home network complications I have had to move my router to a seperate part of the house, therefore the wired network I had set up can no longer work. Before I find the time to go out and buy a Wifi adapter for my desktop PC, I have a laptop that uses a built in Wifi card to connect to my router and this can connect to the internet, and I was wondering if I could somehow access the internet on my desktop PC via my laptop. I'm hoping for a not-so-complex solution as this will only be set up for a few days, but it is quite vital that my desktop computer gets internet access. Does anyone have experience in this sort of thing and can help me out? Thanks.

    Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >