Search Results

Search found 596 results on 24 pages for 'gigabit'.

Page 12/24 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • What software can I use to pinpoint why Windows Server 2003 takes 15 seconds for any operation?

    - by Dr. Zim
    Ram is about 1/2 in use, four CPUs are all but idle. I tried "Microsoft Server Performance Advisor" with no luck. No entries in the Event Log for hardware failures, etc. And yet I can click on the start menu and wait 15 seconds for any new attempt. Launching software takes 30 seconds to respond. The server has an 8 drive WD RE 250 gig each Dell Perc 6 Sata raid array with Intel gigabit network cards. Anyone have any software titles that could analyze what is going wrong with this server?

    Read the article

  • RTL8168B/8111B Lan card is not detected in RHEL5.1..Not finding Lan card driver for this particular

    - by Deepak Narwal
    Hello friends... In My computer Lan card model is Realtek RTL8168B/8111B PCI-E GIGABIT ETHERNET NIC (NDIS 6.20) My system is dual boot windows 7 and redhat 5.1 Now windows 7 automatically detected this lan card but in redhat lan card is not detected.I have tried to through evrywhere like network or through neat-tui but it is not showing lan card.. I tried google also but all of them providing windows software for this lan card . So please anyone can tell me the link so that i can download drivers for this and can use internet there.. Thanks a lot in advance Deepak Narwal

    Read the article

  • Strange Ubuntu Random Display [Video]

    - by d4v1dv00
    I had this random display issue ever since Ubuntu 11.04 and now running Ubuntu 11.10 and this problem still persist. It is very hard for me to explain, so I uploaded a video to elaborate itself. Before I convert from Windows 7, this issue never happened. The symptom is so random that I cannot reproduce or tell precisely when will this happen again. My wild guess is, should this be related to driver? Below are my detail system information: $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation H67 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57788 Gigabit Ethernet PCIe (rev 01) is there any other information i need to post and how do i do that?

    Read the article

  • No WIFI or LAN on Ubuntu 12.04 or 12.10 Live CD/USB using Toshiba qosmio x870

    - by Mighty
    I recently had issues with secure boot and couldn't boot the Live CD/USB but after disabling secure boot, I was able to 'TRY UBUNTU'. My currently problem is that I can't access WIFI or LAN from either Ubuntu 12.04 or 12.10 Live CD/USB which I do from Windows 8. Also, the wireless button is able to turn on and off the wireless LED but doesn't find available WIFI. Please, what should I do to get both WIFI and LAN working on Ubuntu using Toshiba qosmio x870? UPDATED: Here's the output of lspci: ubuntu@ubuntu:~$ lspci 00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1c.4 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1213 (rev a1) 07:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) 08:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8723 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)

    Read the article

  • Computer Studdering When Transferring Over Network

    - by Nalandial
    This is a really weird problem that I've never even seen before. When I copy to or from my server share, my computer studders terribly and the data transfers very slowly at only around 12MB/s. By studdering I mean the mouse skips around and all my applications respond very slowly; as soon as I cancel the transfer it resolves immediately. I looked at Task Manager and the CPU is only at ~35% with plenty of RAM free. This only started semi-recently; before, I had no problems and the transfer speed maxed out the gigabit connection. I have two hard drives in my computer. When I try transferring files between drives it's fine, but when I copy from the share to either drive or to it from either drive, I get studdering. I'm running Windows 7 x64. Anyone have any idea what's going on? Any help would be much appreciated.

    Read the article

  • Frequent Disconnects with an Intel 3945ABG Wireless Card

    - by Alex Forsythe
    I'm brand new to Ubuntu, and I really love it so far, but one issue I have encountered is that my WLAN is disconnecting about every 5-10 minutes. Often times the connection is repaired automatically, but sometimes the network manager will repeatedly reject my encryption key (which of course is correct). Occasionally after a disconnect, the wireless network fails to show up at all. The only way I can solve this seems to be by completely restarting Ubuntu or connecting with a USB wireless adapter. I am using WPA/WPA2 encryption, which I've read can cause problems with network-manager, but I experience the exact same issues with WICD. I should probably note that I've not experienced any of these issues using Windows 7 on my other partition. I have a hunch that there may be a better driver out there for my card, but I have no idea how to go about searching for it or installing it. Any help would be really appreciated! lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric lspci -nnk 09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express [14e4:1600] (rev 02) Subsystem: Dell Device [1028:0201] Kernel driver in use: tg3 Kernel modules: tg3 0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02) Subsystem: Intel Corporation Device [8086:1020] Kernel driver in use: iwl3945 Kernel modules: iwl3945 rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 3: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no

    Read the article

  • Setting up Beats audio on HP Pavilion m6

    - by Joel Auterson
    I have an HP Pavilion m6-1054sa laptop, with a Beats subwoofer on the bottom. The normal laptop speakers work fine under Ubuntu but the Beats speaker(s?) does not. Anyone know how to get this working? Here's my lspci output, if it helps... 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Thames XT/GL [Radeon HD 7600M Series] (rev ff) 07:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5289 (rev 01) 07:00.2 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 0a) 08:00.0 Network controller: Intel Corporation Centrino Wireless-N 2230 (rev c4)

    Read the article

  • RTL8168B/8111B Lan card is not detected in Redhat..Error is make ***/lib/modules/2.6.18-53.e15/build

    - by Deepak Narwal
    0 Hello friends... In My computer Lan card model is Realtek RTL8168B/8111B PCI-E GIGABIT ETHERNET NIC (NDIS 6.20) My system is dual boot windows 7 and redhat 5.1.Redhat is not picking up this model of Lan card automaticlly. I tried it by downloading from realtak site for this particular model and find some .tar packages for my kernal and when i tried to install them ... check old drivers & unload it build the module and install make */lib/modules/2.6.18-53.e15/build: no such file or directory stop make[1]: *[modules] error 2 make : [modules] error 2 i downloaded tar files from sites and unpack according to their instrution i tried to run autorun.sh script as mentioned in readme file but after doing this it is showing above error... Now what to do i am not getting

    Read the article

  • Centrino Wireless-N 1000 takes forever to connect and keeps asking for password

    - by waclock
    A few days ago I started having this problem. When I tried to connect to any WiFi Connection it would stay connecting forever, and after a minute or so it would ask me for the password again. The strange thing is that this happened out of nowhere, I did not install any new drivers or anything like that. After this happened I decided to uninstall ubuntu and install it again ("inside windows") but the problem is still there. Any suggestions would be greatly appreciated. 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:aa:e4:7d size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:50 ioport:4000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:09:9c:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-23-generic-pae firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:c4500000-c4501fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.2 logical name: eth1 serial: ee:85:2f:7d:80:96 capabilities: ethernet physical configuration: broadcast=yes driver=ipheth ip=172.20.10.2 link=yes multicast=yes

    Read the article

  • How do I configure a secondary gateway in RHEL5?

    - by Brett Ryan
    Greetings, we have been experiencing a random timeout issue with VPN users connecting to one of our servers which is causing a problem. My network administrator has instructed me to configure a secondary gateway to include the VPN connection. My current connection resides as follows, 10.1.9.1 is the internal gateway to the internet, I'd like to add 10.1.1.20 as the VPN gateway. # Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet DEVICE=eth0 BOOTPROTO=none BROADCAST=10.1.255.255 IPADDR=10.1.1.22 IPV6_AUTOCONF=yes NETMASK=255.255.0.0 NETWORK=10.1.0.0 ONBOOT=yes GATEWAY=10.1.9.1 TYPE=Ethernet USERCTL=no IPV6INIT=no PEERDNS=yes

    Read the article

  • How to connect two ubuntu computers with ethernet cable

    - by Lukasz Zaroda
    I'm trying to connect with ethernet cable two computers - desktop and laptop. What I want to do is transfer a lot of data from one to another. The problem is that I'm doing everything from: How to network two Ubuntu computers using ethernet (without a router)? But after that, ping always gives me "Destination host unreachable". I was searching a while but couldn't figure out what is a reason it doesn't work, maybe it's something about my devices or maybe someone will have another idea. Ethernet cable I got with my router. There is a text printed on it: Aurit Data Cable Cat.5 UTP 26AWG 4PAIR AWM PUC 75°C EIA/TIA 568B It's connecting now my desktop to router, so I can send this question. My desktop: System: Ubuntu 12.04 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) "ethtool -i eth0" output: driver: r8169 version: 2.3LK-NAPI firmware-version: rtl_nic/rtl8168d-1.fw bus-info: 0000:01:00.0 supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes My laptop: System: Ubuntu 14.04 Ethernet controller: Qualcomm Atheros AR8162 Fast Ethernet (rev 08) "ethtool -i eth0" output: driver: alx version: firmware-version: bus-info: 0000:01:00.0 supports-statistics: no supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no My iptables are accepting everything. Any ideas why I cannot reach other computer?

    Read the article

  • HP Envy 15 3040nr sound issues

    - by Lenny
    I have successfully set up my Envy 15" for Ubuntu 12.04 except for the sound, anyone have any ideas about how to get it working? I had to blacklist snd-usb-audio to my alsa to stop pulseaudio from freezing on login and logout, but now no sound plays. Could anyone provide me with some guidance? lspci info 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:01.2 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) 00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series] 09:00.0 Network controller: Intel Corporation Centrino Advanced-N 6230 (rev 34) 0a:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5116 PCI Express Card Reader (rev 01) 10:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) 11:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

    Read the article

  • Always use one slow connection in preference of a "faster" one

    - by billc.cn
    In Windows, there's this automatic metric thing where the metric is selected according to the declared speed of the link. I now have a gigabit LAN routed to a 2MB DSL service and a HSDPA mobile broadband connection. The former is always chosen for Internet packets even though the latter is actually faster. I tried setting the mobile broadband's interface metric to 1 and raising its priority in the advanced settings of the adapter settings, but this does not seem to affect the metric of the default route. The default route to the Ethernet interface always have a lower metric than the mobile broadband interface. Am I missing something here?

    Read the article

  • Cat 6 Only 100mbit speed

    - by Stu2000
    I tried two different cat6 cables directly connected between my two ubuntu machines. This one I ordered online: http://www.amazon.co.uk/gp/product/B002SQPDXS/ref=wms_ohs_product only achieves 100mbit speeds, but does appear to be supporting cross-talk (direct pc to pc), the other cat 6 cable, worked perfectly and gets the full 1gigabit speed. Both tests were performed using ftp and checking the network monitor with direct pc to pc connection. Did the product from amazon lie to me or do I need to manually set a setting somewhere in ubuntu for some cables? I had thought 10 quid for 20m of gigabit ethernet cable was a bit cheap, you get what you pay for... Regards, Stu Update: It seems that after rebooting, the device is set to 1000mbit sec when looking it up with sudo ethtool eth0 However after a while, this will drop down to just 100, after which to reset it to 1000 again, I have to reboot, and simply unpugging and re-plugging in the cable doesn't do it. I tried setting this in networking config file as suggested here: auto eth0 iface eth0 inet static pre-up /usr/sbin/ethtool -s eth0 speed 1000 duplex full but that resulted in my networking failing to start. Is there a problem with my 'auto-negotiation' or something? Can I manually override a setting to 1000mbit?

    Read the article

  • RAID Read/Write Speed Gradually Slows

    - by Nalandial
    This is actually a server at home, but I felt it was sufficiently complicated as to not have it on SuperUser and could easily apply to a professional situation. I have a file server running Debian (Lenny 5.0.4), and it has an XFS LVM on top of a RAID 5 with the OS drive separate from the RAID. It's also running apache, samba, and postgresql. Side note: before anyone asks, I'm using RAID5 because I get more bang for the buck on raw drive space, and still have some fault tolerance. When the box is started (via shutdown or reboot) reading/writing to it's samba share maxes out the gigabit network connection. Over time, this slowly degrades eventually becoming < 10MB/s; however, when rebooted the speed returns to maxing out the connection. Why is this happening, and is there a way to 'clear' out whatever's causing it without taking the server down? Thanks in advance!

    Read the article

  • Nginx Static Content Server Maxing Out?

    - by Harry
    I use nginx to serve the static content for a decently busy website of mine. I have the logging disabled, and 4 worker processes enabled with 5,000 connections per worker (which should yield a max connection limit of 20,000. The server is only operating at about 10% CPU usage and 50% ram, but it's very laggy, and sometimes nginx is so slow to respond to the requests, it times out. For a small number of connections, it's fine, but once any load starts occurring (~2,500 connections), it backs up and bogs down. Is there any other bottlenecks or limits that I might be hitting? This is a FreeBSD server, and all the static files are located locally (not NFS). The NIC is an unmetered gigabit, and it's only using around 75 megabit. Any insight would be appreciated. Thanks.

    Read the article

  • Struggles to connect to network when using WPA with a BCM43225

    - by pst007x
    When booting my laptop, it will try to connect to my wireless network, however a window keeps popping up asking me for my security password, which has already been saved. I have to keep deleting my network settings, and reconnecting, otherwise it keeps failing to connect. My wireless is set up with a WPA, I do not want to lower my security because of this, but it is a pain and can take me 15mins plus to finally connect. The problem has only become apparent since a fresh install of 11.10. IPV6 disabled. System info: 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) Subsystem: Acer Incorporated [ALI] Device 036d Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at b3400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: tg3 Kernel modules: tg3 02:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) Subsystem: Broadcom Corporation Device 04da Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at b2400000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: wl, brcmsmac ADDITIONAL: In terminal I get this: pst007x@pst007x-ubuntu64:~$ nm-applet start ** Message: applet now removed from the notification area ** (nm-applet:2816): DEBUG: old state indicates that this was not a disconnect 0 ** Message: using fallback from indicator to GtkStatusIcon ** Message: applet now embedded in the notification area ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. ** (nm-applet:2816): DEBUG: foo_client_state_changed_cb Note this line: ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. At this point is where I am asked for the password. Please report WPA issues with Ubuntu 11.10 here: https://bugs.launchpad.net/ubuntu/+source/network-manager/+bug/892727

    Read the article

  • Linksys EA3500 : use WAN port as WAN + LAN possible?

    - by Dough
    I'm waiting for deliver of a Linksys EA3500 router. I was wondering if it was possible to get the WAN port act as normal WAN port (Internet IP) + LAN switch ? My problem is that my Internet box is in a room with NAS and PC, and the router will be in another room with TV, PS3 and PC. The Internet box have a 4 port Gigabit switch so one cable will plug from there to the router's WAN in the other room. The router will get the Internet IP from the Internet box, but will it be possible to have private network through this link too ? I could have a first network between the Internet box and the router, and another network form router and devices but that will do double NAT for nothing... Thanks for reading me and your help !

    Read the article

  • wifi not working hp dv4

    - by Blaze
    i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

    Read the article

  • No Wireless In Ubuntu 13.10

    - by viktorhubinette
    When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    Read the article

  • How to get my laptop to detect SD cards inserted into its built-in card reader?

    - by Candelight
    My laptop has a built-in SD Card reader but it cannot detect one when inserted. Here is the result when I type lspci from the terminal: 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:12.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (rev 80) 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80) 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83) 00:14.1 IDE interface: ATI Technologies Inc IXP SB400 IDE Controller (rev 80) 00:14.2 Audio device: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller (rev 01) 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80) 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS482 [Radeon Xpress 200M] 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 05:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 05:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 05:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 05:09.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g

    Read the article

  • Windows file sharing connects over WiFi instead of LAN

    - by zacaj
    I have a laptop and a desktop computer, and I need to sync lots of files to the laptop and back whenever I go on a trip, etc. I've got a LAN cable connected into an extra port on the desktop that I plug into the laptop so I can get gigabit file transfers instead of wireless G. They connect fine. If I do an FTP transfer, for instance, using the LAN IP addresses, it goes at ~40MB/s, as it should. However when I copy files using explorer and native windows file sharing it detects the other computer by name, not IP (eg \\DESKTOP-PC\ instead of \\192.168.0.100\) and always connects to it by its wireless IP address instead of the faster LAN address. Both computers are running Windows 7. I have tried editing the priorities of the adapters in Advanced Settings and putting the LAN adapters above the wifi ones, but this didn't have any effect

    Read the article

  • Cannot establish Wired connection on Acer Aspire 5930G

    - by drakos46
    I use an Acer Aspire 5930G, dual booted with Windows 7 and Ubuntu 13.10. My problem is that i cannot establish wired connection on my ubuntu. Wireless connection works in both of my OSs but the Wired connection does not, only on the Ubuntu. I have already tried the common fix: echo on | sudo tee /sys/class/net/eth0/device/power/control but without any results. Any ideas? eth0 Link encap:Ethernet HWaddr 00:1d:72:c2:21:a5 inet6 addr: fe80::21d:72ff:fec2:21a5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:945 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:204318 (204.3 KB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:7241 errors:0 dropped:0 overruns:0 frame:0 TX packets:7241 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:645874 (645.8 KB) TX bytes:645874 (645.8 KB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:57:7b:cc inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::216:eaff:fe57:7bcc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:19937 errors:0 dropped:0 overruns:0 frame:0 TX packets:16933 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10877245 (10.8 MB) TX bytes:3131378 (3.1 MB) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8071 PCI-E Gigabit Ethernet Controller (rev 16)

    Read the article

  • OpenVPN Configuration - Windows 7 client & debian server

    - by Guillaume
    I recently formatted my Windows 7 computer and lost my client's config files for OpenVPN. I recovered the certificates and default config that were left on the server but I haven't managed to make the whole thing work again. I assume the server's config and routing table are OK because it was working before (although quite some time ago). Would any of you experts be able to help? server.conf # Serveur TCP/666 mode server proto udp port 666 dev tun # Cles et certificats ca ca.crt cert server.crt key server.key dh dh1024.pem tls-auth ta.key 0 cipher AES-256-CBC # Reseau server 10.8.0.0 255.255.255.0 #push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" push "redirect-gateway def1" keepalive 10 120 # Securite user nobody group nogroup chroot /etc/openvpn/jail persist-key persist-tun comp-lzo # Log verb 3 mute 20 status openvpn-status.log log-append /var/log/openvpn.log client.conf # Client client dev tun proto udp remote *my server's ip address*:666 cipher AES-256-CBC # Cles ca ca.crt cert client1.crt key client1.key tls-auth ta.key 1 # Securite nobind persist-key persist-tun comp-lzo verb 3 Routing table on debian server when OpenVPN server is running: Destination Gateway Genmask Indic Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 my server's ip * 255.255.255.0 U 0 0 0 eth0 default 72815.trg.dedic 0.0.0.0 UG 0 0 0 eth0 Routing table on Windows 7 client (OpenVPN not working) =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: [...] =========================================================================== Persistent Routes: None And when the link is established between my client and the server: The server's routing table stays the same. The client's becomes: =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 my server's ip 255.255.255.255 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Persistent Routes: None What's working: Server and client do connect to each other, SSL certificates are OK. The client gets an IP (10.8.0.6) from the server OpenVPN client is started as an administrator. But: I cannot ping the other one on either side. 'Gateway' value is empty on client's side (in the adapter's "status" window). Client has got no internet access when the link is up. Ideal configuration: I only want the client to be able to use the server's Internet access and access its resources (MySQL server in particular). I do not need or want the server to access the client's local network. The client needs to be able to access it's local network, although all Internet traffic should be redirected to the VPN link. I spent a considerable amount of time on this but it's still not working, any help would be much appreciated. Thanks :)

    Read the article

  • How to tell if you are connected to Wireless B, G or N?

    - by Raheel Khan
    I am using Windows 7 on all wired desktops and wireless laptops in my home network. I recently upgraded my Ethernet switch to Gigabit and instantly noticed an increase in throughput in wired devices. I also bought a Wireless-N WAP but with degredation in wireless file transfer speeds. I have been told that a number of reasons could affect wireless speeds including which WAP is used, how many wireless devices are connected, which security mode is used, etc. However, that remains irrelevant to my question. Each of my laptops claim to support Wireless-N but I cannot seem to figure out how to determine if the laptops are truly running Wireless-N or are connected to the WAP through some sort of mixed-mode. I do not have control of the WAP device so cannot tell what mode it is running in. Is there a way to tell which mode is being used and what the throughput is for each connected device without having access to the WAP interface?

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >