Search Results

Search found 596 results on 24 pages for 'gigabit'.

Page 13/24 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• Wifi - wireless network not working after installing Ubuntu 12.04

  - by Nilesh

  I had installed ubuntu 12.04 in my Dell Vostro 3460. Initially wired as well wireless both are not working. After installing compat-wireless-2012-07-03-pc.tar.bz2 wired network fine but wireless is not working. Previously both were working fine with ubuntu 11.10. Also presently both network are working fine in Win7. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) iwconfig: lo no wireless extensions. eth0 no wireless extensions. ifconfig: eth0 Link encap:Ethernet HWaddr 84:8f:69:d4:35:9b inet addr:10.24.22.72 Bcast:10.24.31.255 Mask:255.255.224.0 inet6 addr: fe80::868f:69ff:fed4:359b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15332 errors:0 dropped:0 overruns:0 frame:0 TX packets:10425 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:9262594 (9.2 MB) TX bytes:1572030 (1.5 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1432 errors:0 dropped:0 overruns:0 frame:0 TX packets:1432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145656 (145.6 KB) TX bytes:145656 (145.6 KB)

  Read the article

• Seasgate GoFlex NAS + Horrible Speed = Bad Experience

  - by Jon H

  I am having issues with transfer speeds from my desktop PC to my NAS. I have my NAS hooked up to a Gigabit Gateway as well as my Desktop with Cat 5e. I see up to 4.0 MB/Second Transfer Rates, the normal is about 2.5 MB/Seconds. There is 3 Partitions on my NAS, Public, Private, Backup. When I transfer from Private to Public I see the speeds above. If its under the same partition almost instant. I was wondering if the speeds I am seeing is in due to my Computer or the NAS. I was looking into building my own Media Server in due to these horrible speeds. Is their anything I can do in the mean time to speed this up? Motherboard = M3970AM-HP (Angelica) Processor = AMD FX 6100 Ram = 10GB PC3-10600 MB/sec Hard Drive (1) = 1.5TB SATA 3.0GB 5400RPM Hard Drive (2) = 120GB SATA SSD NAS = Seagate 3TB Go Flex Home Connection (1) = 1000 Base T Connection (2) = Wireless N

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• LIfebook lh531 inbuilt card reader not working

  - by chandrasekar

  Inbuilt card reader (SD/PRO/SDHC) not working. When I insert the memory card the indicator comes for a milli second and nothing happens. When I do lspci it gives the out put which is pasted below: I use Ubuntu 11.10. Pl help pro-hq@prohq-LIFEBOOK-LH531:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 (rev 34) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) pro-hq@prohq-LIFEBOOK-LH531:~$

  Read the article

• Touchpad right click doesn't work on HP Envy 14 beats

  - by jdrageme01

  I have Ubuntu 12.04 lts 64 bits on my HP envy 14 beats. When I try to click with the right click button it doesn't work. Only works click in the touchpad directly and with usb mouse. 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) 00:01.1 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0105] (rev 09) 00:01.2 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0109] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05) 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) 00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5) 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 05) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05) 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series] [1002:6741] 09:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) 0a:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) 0b:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04)

  Read the article

• Ubuntu 12.04 server froze during the first boot after it was installed.

  - by user69021

  I installed Ubuntu server 12.04 to my new server and it failed on the first boot. It just stopped and I can't proceed any further. Server's specifications: Dell PowerEdge T620 CPU : Xeon E5-2665 2.4G x 2 RAM : 8GB RDIMM, 1333MHz x 12 HDD : 3TB Near Line SAS 7.2K x 8 RAID controller : PERC H710 GPU : NVIDIA Tesla C2075 x 4 I have a screenshot of the screen it stopped on but I cannot attach it because my privilege level is currently too low. ![freeze on boot][1] Here are the last messages while booting. [5.048743] Freeing unused kernel memory : 920k freed [5.049046] Write protecting the kernel read-only data : 12288k [5.052973] Freeing unused kernel memory : 1608k freed [5.056132] Freeing unused kernel memory : 1196k freed Loading, please wait... [5.070236] udevd[218]: starting version 175 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. [5.089030] megasas: 00.00.06.12-rc1 Wed. Oct. 5 17:00:00 PDT 2011 [5.089518] megasas: 0x1000:0x005b:0x1028:0x1f35: bus 1:slot 0:func 0 [5.089739] megaraid_sas 0000:01:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 [5.089937] megasas: FW now in Ready state [5.090427] dca service started, version 1.12.1 [5.091463] Intel(R) Gigabit Ethernet Network Driver - version 3.2.10-k [5.091578] Copyright (c) 2007-2011 Intel Corporation. [5.091712] igb 0000:06:00.0: PCI INT A -> GSI 16 (level,low) -> IRQ 16 [5.111090] megasas:IOC Init cmd success [5.123124] usb 1-1:new high-speed USB device number 2 using ehci_hcd What can I do about this?

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• Effect of using dedicated NVidia card instead of Intel HD4000

  - by Sman789

  Short version: Can someone please advise me of the effect of adding a dedicated NVIDIA GeForce GT 630M card to an Ubuntu laptop in terms of power consumption and performance gains/losses when doing general productivity tasks and booting up. Also, how good are the closed source, open source, and Bumblebee drivers for these newer cards compared to support for the Intel HD4000? Long version/Background, if any info here is helpful: I'm thinking of ordering a laptop from PC Specialist (a UK company who actually sell machines without Windows pre-installed) with the following specifications: Genesis IV: 15.6" AUO Matte 95% Gamut LED Widescreen (1920x1080) Intel® Core™i5 Dual Core Mobile Processor i5-3210M (2.50GHz) 3MB 4GB SAMSUNG 1600MHz SODIMM DDR3 MEMORY (1 x 4GB) 120GB INTEL® 520 SERIES SSD, SATA 6 Gb/s (upto 550MB/sR | 520MB/sW) Intel 2 Channel High Definition Audio + MIC/Headphone Jack GIGABIT LAN & WIRELESS INTEL® N135 802.11N (150Mbps) + BLUETOOTH Now, as I want this laptop mainly for work and not for games, I would be more than content with the HD4000 integrated chip which comes with the processor. However, for compatibility reasons, I am not able to get the specs I want unless I choose a NVIDIA GeForce GT 630M 1GB graphics card, which I don't have a great deal of use for. I'm willing to buy it, however, as it's still cheaper than any other laptop with the specs I want. However, I know that Linux power management isn't fantastic with open-source graphics drivers, and I don't much about Bumblebee. Basically, whilst I'm happy to 'tolerate' the card being there, I don't want to experience any negative effects on the rest of my system (battery, performance etc) and if there are likely to be any, I might reconsider my purchase. So if anyone can advise me on the effects, I would be very grateful, since I doubt I can just turn the card off. Thankyou for any assistance :)

  Read the article

• No Internet access while being connected to VPN using Cisco VPN Client 5.

  - by szeldon

  Hi, I have an access to corporate VPN using Cisco VPN Client 5.0.00:0340, but when I'm connected to it, I don't have an Internet access. I'm using Windows XP SP3. As it was suggested here http://forums.speedguide.net/showthread.php?t=209167 , I tried to enable "Allow local LAN Access" but it doesn't work. I also tried a second solution - deleting entry using "route" command, but it didn't help. I used "route delete 192.168.100.222". It's a third day of my attempts to solve this issue and I don't have an idea what else to do. I'm not very experienced in VPN stuff, but I know something about networking. Basing on my knowledge, I think that it's theoretically possible to achieve Internet access using my local network and only corporate stuff to be routed using VPN connection. I think that theoretically this should look like this: every IP being inside by corporation - VPN interface IP every other IP - my ethernet interface I've tried many possibilities of how to change those routes, but neither of them work. I'd really appreciate any help. My route configuration before connecting to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 192.168.101.254 192.168.100.222 10 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 1 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 3 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 192.168.101.254. =========================================================================== My route configuration after connection to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport 0x170006 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 10.251.6.1 10.251.6.51 1 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.0 255.255.255.0 10.251.6.1 10.251.6.51 10 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.1.150.10 255.255.255.255 192.168.101.254 192.168.100.222 1 10.251.6.0 255.255.255.0 10.251.6.51 10.251.6.51 20 10.251.6.51 255.255.255.255 127.0.0.1 127.0.0.1 20 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 10.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 10 192.168.100.0 255.255.254.0 10.251.6.1 10.251.6.51 10 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 10 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 10 213.158.197.124 255.255.255.255 192.168.101.254 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 30 224.0.0.0 240.0.0.0 10.251.6.51 10.251.6.51 20 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 10 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 10.251.6.1. ===========================================================================

  Read the article

• Ubuntu 12.04 desktop, VNC viewer not refreshing screen

  - by user73279

  I've had this issues across multiple machines and multiple versions of Ubuntu desktop (all 10.04 or later). Usually it happens with an old laptop I've put Ubuntu on but now it's happening on my primary dev machine (a quad-core PC recently upgraded to Ubuntu 12.04 desktop). The problem is this - I can connect to the machine and login with the password, the initial screen looks fine but never refreshes. I can see the monitor for the machine across the room and can see the mouse move and the menus pop up but the image of the screen on the PC in front me running the VNC viewer never updates. So the mouse and keyboard commands are working. Ubuntu 12.04 Desktop Ultra VNC Viewer (also seen with RealVNC's free VNC viewer) Desktop Sharing Static IP on eth0; Dynamic ID on eth1 I think it is an Ubuntu config issue because this PC used to work just fine with 9.04, 10.04, and 11.10 (over the past couple of years). I've also had a couple of laptops that used to have this issue with older Ubuntu's but don't with 12.04. Additional info: The Win7 PC I'm trying to use to control the Ubuntu PC is connected via 2 DLink 8-port gigabit routers. The Ubuntu laptop I usually control via VNC is typically only connected to the network via wireless. The screen refresh is choppy but usable. I've repeated the issue on a Win7 laptop which was connected via ethernet and wireless.

  Read the article

• Win 2003 STD network adapter always showing DHCP when in static IP configuration, + it loses the DNS

  - by Darragh

  Hi, I have a server that after the first configuration it was DHCP, now I have added it to our domain and in a static IP, however after a few moments it returns to DHCP but with only some of the IPv4 setting staying the same, It loses DNS for example. I'm not sure what is causing the problem but all I know is this started to happen after I added it to the domain, Would it be a domain policy? or the NIC drivers Spec; Dell M605 Blade server Windows 2003 STD SP1 Intel Xeon Quad core NIC: Dual embedded Broadcom NetXtreme IITM 5708 Gigabit Ethernet NIC w/ TOE

  Read the article

• how can i realize a video-wall on 3-9pc with vlc

  - by Luca

  hello! i have to create a videowall, from 3 to 9 monitor. every monitor as a pc. actually, i stream from a server 9 movies with different istances of VLC, but i could also play on every machine the relative video with a single player. there's no problem. the real problem is that i really dont know how to sync the videos on a LAN...unfortunately there is a NETSYNC module inside VLC wich is NOT working. here are some info about my setup: videowall from 3 to 9 monitor || from 3 to 9 pc, all with the same configuration || a gigabit router+switch for the "dedicated" LAN im really stuck in this situation, if anyone has an idea or just a completely different solution, please, share it with me! thanks a lot in advance! :)

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• Windows 7 "Could not reconnect all network drives" on boot

  - by Thermionix

  Windows 7 won't reconnect to my network drives on startup. Once it is done booting opening Windows Explorer and clicking each share will mount them. Windows 7 Enterprise N Service Pack 1 I have attempted formatting the windows machine - first thing done to machine was to map the network drives, upon reboot they were disconnected. It is running on an Crucial M4 64gb SSD. The host of the network shares is a Ubuntu-Server machine connected through a gigabit switch. A modem provides dhcp, although both these machines have static IP's defined. It won't reconnect the drives regardless of whether they're SAMBA shares or NFS shares - therefore I believe it's an issue with the windows machine. Ubuntu 11.10 (GNU/Linux 3.0.0-12-server x86_64) I've tried using ip address instead of netbios name for mapping shares on the windows machine, Also tried setting EnableLinkedConnections=1 gpedit.msc Computer Configuration - Administrative Templates - System-Logon - always wait for the network at computer startup and logon = yes

  Read the article

• Lost WiFi after 12.10 upgrade

  - by Steven Guillory

  I received my new Dell Vostro 2420 last week, and just got around to upgrading from 11.10 to 12.10. Unfortunately, like many others (after researching the issue), I no longer have WiFi. I have tried every sudo command given that worked for others, and still can't get my wireless to function. I am new to Linux, so any and all help is appreciated. Thanks in advance! Edit: I can connect via ethernet, just not via wifi. As a matter of fact, when I use Fn + F2 to turn on wifi, only my bluetooth comes on. lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 07:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) This is what I am getting... dpkg: error: --install needs at least one package archive file argument Type dpkg --help for help about installing and deinstalling packages [*]; Use dselect or aptitude for user-friendly package management; Type dpkg -Dhelp for a list of dpkg debug flag values; Type dpkg --force-help for a list of forcing options; Type dpkg-deb --help for help about manipulating *.deb files; Options marked [*] produce a lot of output - pipe it through less or more !

  Read the article

• why is there so much variance in prices for a 2-bay NAS?

  - by jcollum

  I'm considering buying a 2bay NAS for media storage. I'm perplexed by the variety of prices. They go from about $115 to $1200. The only thing I could see that differentiated the high end drive was encryption and a dual gigabit ethernet port. I don't understand how that can add up to $800+ dollars. Clearly I should know why there's this price variance before considering buying a 2 Bay NAS. Newegg link to 2 Bay NAS Should I move this question to serverfault?

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• Improve performance on Lync desktop sharing

  - by Trikks

  I'm using Lync 2010 server to handle some clients communication and screen sharing. The biggest issue is the performance with screen sharing, it is of rather high quality but the frame rate is very poor. I have been reading and searching a lot on the subject and 95% of all topics is about bandwidth, we have a 200/200 MBit Internet connection solely for this application. Also my test machines runs on an internal gigabit lan. The speeds between all boxes is hysterically fast. Next step was to ensure that there where some profiles for different bandwidths, so i registered some New-CsNetworkBandwidthPolicyProfile -Identity 50Mb_Link -Description "BW profile for 50Mb links" -AudioBWLimit 20000 -AudioBWSessionLimit 200 -VideoBWLimit 14000 -VideoBWSessionLimit 700 New-CsNetworkBandwidthPolicyProfile -Identity 100Mb_Link -Description "BW profile for 100Mb links" -AudioBWLimit 30000 -AudioBWSessionLimit 300 -VideoBWLimit 25000 -VideoBWSessionLimit 1500 Nothing fancy happend here either. Non of the test boxes have anything from Norton installed, they doesn't have any firewalls running (nor does the Lync server), all fences are down in this environment just for the testing. Is there any thing that I may have missed to improve the quality of this? Thanks

  Read the article

• Can I increase the link speed of the RAS Server on our MS Win2k3 box?

  - by Ducain

  We are running a Win2K3 Server box, and I'm a remote employee that connects via VPN. I've been frustrated for some time by the connection speed over the VPN (the office HQ has a decent speed and I have a biz class connection here), and decided to do some checking today. This morning, I was dialed in and looked at the networking tab of the task manager, and I see that the adapter for the RAS Server (the box has 4 Gigabit adapters) has a speed that seems far too low. The speed for the RAS Server link hovers between 300 - 600 Kbps. The local connection (and others) all say 1 Gbps. Can I set this to a higher speed? Is this information accurate? Thanks for the input.

  Read the article

• Performance problems on RDC to our Terminal-Server Win2008 R2

  - by user40021

  Hello, we have a new win2008-R2 (2x Xeon X5570, 32GB RAM). There I have installed the terminal-server roles, thats all OK. Currently 5 users are working at this server, but all get a very low performance in their remote-desktop session. Sometime it takes 1-2 seconds till the keyboard-inputs will be performed and shown. At the clients I run RDP v 6.1 We have also an older TS-server (based on Win2003 with an Opteron-CPU), there are working about 20 users at the same time. There I do not have the troubles with the inputs at the remote-desktop sessions. Both servers are connected to the same gigabit-switch. Any ideas what could cause the troubles at the Win2008 R2? Many thanks in advance. Regards Chris

  Read the article

• Poor quality when trying to stream a 720p video to XBox 360 using Media Center Extender

  - by MBraedley

  I have my XBox 360 set up as a Media Center Extender for my Windows 7 desktop. SD quality avi videos stream fine to my XBox, either though the video library or through Media Center Extender, but when I try a 720p mkv file, the frame rate plummets and the A/V sync is completely lost. I don't want to transcode or switch container formats (mkv isn't supported by the 360), but still want to stream. Both my desktop and 360 are plugged into the same gigabit switch, which is plugged into my ISP supplied modem/router. The video plays fine on my machine in a number of programs. Considering that I should have more than enough bandwidth to accommodate this video, why won't it play back properly?

  Read the article

• Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

  - by user42424

  So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

  Read the article

• Esxi with iSCSI SAN slows down with many multiple VMs running

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas). Those two machines are connected to each other with Gigabit ethernet, and a procurve switch in between. After a while, if I have many(4-5 or more) vms running, they start to get un-responsive (long delays before anything happens). We are trying to find the reason behind this. Today we looked at esxtop, and found that DAVG of that iSCSI LUN stays at 70-80. I read that +30 is critical! What could be causing those high response-times?

  Read the article

• Multiple Graphics Cards on Fedora 15 (Gnome 3)

  - by Michael

  I have the (delightful) misfortune of having 3 graphics cards. They are XFX Radeon 5750s. Each drives 2 monitors via dvi. I am having a really hard time getting these running on fedora 15 (gnome 3). So my setup is 3 columns of 2 monitors (the upper monitor is mounted upside down in each column to reduce the bezel between monitors). When the (graphical) login screen comes up all 6 have the blue stripey background that must be the default, but then when I login, things get interesting. In the xorg.conf below, you will see only 2 of the screens in the serverlayout while the other 4 are commented out. Logging in with only 2 of the screens active works well (and it even remembers that the top one is upside down, and should be considered above the lower, i am not sure where it stores this info, but i set it using the graphical "Displays" settings) However, as soon as I uncomment a third screen, or more, it gives me an error message when I login. It's one of those friendly, less helpful messages (Oh no! Something has gone wrong. A problem has occurred and the system can't recover. Please log out and try again). If i do not use an xorg.conf, then the "Displays" prefs pane shows only the two monitors on one of my graphics cards Thanks to anyone who can help me get going! (xorg.conf and then lspci below, and xorg log) xorg.conf Section "ServerLayout" Identifier "X.org Configured" Screen "Screen0" 0 0 Screen "Screen1" Below "Screen0" # Screen "Screen2" RightOf "Screen0" # Screen "Screen3" RightOf "Screen1" # Screen "Screen4" RightOf "Screen3" # Screen "Screen5" RightOf "Screen4" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "catalogue:/etc/X11/fontpath.d" FontPath "built-ins" EndSection Section "Module" Load "record" Load "dri" Load "dbe" Load "extmod" Load "dri2" Load "glx" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor3" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor4" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor5" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" Identifier "Card0" Driver "radeon" BusID "PCI:4:0:0" EndSection Section "Device" Identifier "Card1" Driver "radeon" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Card2" Driver "radeon" BusID "PCI:6:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Card0" Monitor "Monitor1" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Card1" Monitor "Monitor2" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen3" Device "Card1" Monitor "Monitor3" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen4" Device "Card2" Monitor "Monitor4" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen5" Device "Card2" Monitor "Monitor5" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection lspci output follows [tgm@tgm ~]$ lspci 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 02:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:02.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 04:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 04:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 05:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 05:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 06:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 06:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) xorg log (posted to fpaste due to how long it is. thanks to marcusw for the request) http://www.fpaste.org/r5ww/ xorg log with all 6 monitors enabled in xorg.conf (they all turn on and have blue, but then one gets the aforementioned user-friendly error message). http://www.fpaste.org/X63H/

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >