Search Results

Search found 26097 results on 1044 pages for 'network share'.

Page 123/1044 | < Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >

• Is proprietary vendor software required to use a wireless printer?

  - by sajee

  On Windows Vista, other than the driver, one can use a regular printer w/o any extra software, either plugged in via USB or over the network. I don't have to install extra software from the printer vendor to use the basic printer functionality. Is the same true for wireless printers? I need to install the HP 6000 wireless printer, and I hate installing vendor software other than the required drivers. So I'm wondering whether I need to install HP software on every PC that wants to use this printer? I haven't had a chance to read the manual but I'm hoping I don't have to. Can folks that have experience with wireless printers comment on whether vendor software, other than the printer driver, is required to use a wireless printer?

  Read the article

• Ways to polling server status

  - by Yijinsei

  Hi guys, I create the same question is stackoverflow, but I was recommended to post my question here. So I apologies for those who saw this post twice. I am try to create a JSP page that will show all the status in a group of local servers. Currently I create a schedule class that will constantly poll to check the status of the server with 30 second interval, with 5 second delay to wait for each server reply, and provide the JSP page with the information. However I find this way to be not accurate as it will take some time before the information of the schedule class to be updated. Do you guys have a better way to check the status of several server within a local network?

  Read the article

• Wireless printer going offline upon entering power save mode

  - by Regmi

  I recently bought a printer, Samsung ML1865W, a wireless laser printer. It works very well, wirelessly until after a while, it goes to power save mode when the printer goes offline. I then cannot connect to the printer (pinging the ip and various ports associated with it do not give any response) until I power cycle the printer. I have checked my wireless settings and my router, I have installed the printer software in WinXP, Win2000 and in Mac and the printer behaves just the same. Any ideas if the printer hardware itself is broken or that its something on my network/application side that's the culprit. If you own the printer, have you had any trouble like that at any time?

  Read the article

• rsync creating thousands of ..ds_store files from mounted volume

  - by daniel Crabbe

  I've been using rsync on OS X to sync all our website admins. It was working fine until the OS X 10.6.3 update! Now it creates thousands of empty (0-kb) folders. It only does it when synching to a mounted network drive (which we need to do) as when I sync to my local drive it works as usual! I've tried excludes which don't seem to be working... also tried a different version of rsync so it's an OS X issue. echo "" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" echo " SYNCING up KINEMASTIK" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" /usr/local/bin/rsync -aNHAXv --progress --exclude-from 'exclude.txt' /Volumes/Groups/Projects/483_Modern_Activity_Website/web/youradmin/ /Users/dan/Dropbox/documents/WORK/kinemastik/WEBSITE/youradmin/ echo "" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" echo " SYNCING up CHRIS BROOKS YOURADMIN" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" /usr/local/bin/rsync -aNHAXv --progress --exclude-from 'exclude.txt' /Volumes/Groups/Projects/483_Modern_Activity_Website/web/youradmin/ /Volumes/Groups/Projects/516_ChrisBrooks/website/youradmin/ Has anyone experienced the same problem?

  Read the article

• tacacs+ integrated with LDAP or database. Which is better?

  - by chingupt

  We are setting up TACACS+ in our network which is a mix of Cisco AP's and other brands. However we have a centralized managemnet system which allows our customers to configure services. Hence we would like to setup a tacacs+ server integrated with some central system. We have two options: Integrate with a central Database server which stores the user configuration. OR Integrate with a LDAP Server. Which is a better solution? Can you please suggest the pros and cons of using LDAP or Database? TIA Sachin

  Read the article

• Change desktop background at school

  - by Nano8Blazex

  On school computers, I can log in with a user account stored on the school network (something like that, I have no experience in networking and this sort of stuff). Everything is fine and dandy and totally works as it should, but there is one thing that I find annoying. Apparently for some reason I can't change my background to anything more than a couple of different solid colors with our school's logo still stuck in the middle. (the original background is a white logo on black background. If I change it to a different color, the central 6x6 inch black/white logo still remains, only the surrounding color is changed.) It may have been set by school administrators or something, I don't really know. I find this really ugly. Is there any way to change a setting so that I can set the background to any picture I wish? (like on a home pc...) Thanks.

  Read the article

• RSync to WebDAV mounted volume very slow

  - by AlexC

  I have a mounted WebDAV store, which I am playing around with to try and put together my own pseudo-DropBox set up. However, it seems very slow to upload larger files (my bandwidth graph goes ok for a little bit, then just stops dead for long periods of time). Has anyone tried this? I'm wondering if the way it gets mounted makes rsync think it's a local drive or something and so may be chattier than it would be if it knew it was a mounted network drive? (I'm new to rsync so may be all wrong here!) I'm syncing using rsync -rv /source/directory/ /mounted/webdav/directory/ This is running using MacOS 10.6, and WebDAV is mounted using the native mounting mechanism.

  Read the article

• Fixing mac user file permissions, not the system

  - by Cawas

  Usually those files get wrong permission when coming from the network, even when I copy them from it, but mostly through "file sharing". So, definitely not talking about Disk Utility repair here, please. But regardless of how the file got wrong permission, I know of two bad ways to fix them. One is CMD+I and the other is chown / chmod. The command line isn't all bad but isn't practical either. Some times it's just 1 file I need to repair, sometimes it's a bunch of them. By "repair" I mean 644 for files, 755 for folders, and current user:group for all of them. Isn't there any app / script / automator out there to do that?

  Read the article

• DNSHost.exe trojan found, now after fix, no one can print

  - by Matt Dawdy

  What started today as an inability to get to the internet (but people could get in just fine), morphed to we realized that the DNS Server wasn't working, then we figured out that we had a trojan called DNSHost.exe (spybot.rl I think), and we disabled its service entry and deleted the offending file and all registry keys told to use by the Trend Micro site. Now, we can get on the internet, but the printer being served by this machine (called server2) cannot be printed to from any client machine on the network. We get the error "The RPC Server is unavailable". I'm assuming that this is related to the DNS issue we had earlier, as we were able to print just fine until this fun happiness started this morning. Anyone have any solid suggestions? Windows Server 2003 R2 SP2, and the client machine are all Windows XP SP2.

  Read the article

• How to check for bottlenecks in Windows Server 2008 R2

  - by Phil Koury

  I recently switched out a 10 year old server for a brand new server in a small office and upgraded from Windows Server 2000 to Windows Server 2008 R2. After the switch was complete and some configurations were changed around we are running into what appear to be some bottlenecks in the network speed. Accessing programs on the server is slower (resulting in long loading times, slower report generation, etc.) than it was on the old server hardware. I am wondering what options or tools I have, if there are any at all, to find out exactly where these hang ups might be coming from.

  Read the article

• how to run an AFS file server on a specific ethernet card (in Debian)

  - by listboss

  I have a linux box running Debian server with minimal number of packages (so no GUI for network management). The box has two ethernet cards, one of which (eth0) is connected to a Mac OSX computer using a cross-cable. I can bring up eth0 and assign a static ip (10.10.11.16) to it. This way I can ssh to the box through the cross-cable. This is what I run on Linux box: ifconfig eth0 10.10.11.16 netmask 255.255.255.0 up I also installed/started a file server (AFS) on Debian. So far, the file server can only be accessed through eth1 which is exposed to my home LAN and www. My goal is to set up the file server so that it's only visible through eth0. Is this possible? and if yes, how can I do it?

  Read the article

• Windows refuses to believe printer is online unless I delete and re-add it

  - by Marcin

  I have a Canon MP560. It is online, in the sense that (a) I can connect to its internal web server; and (b) if I delete the printer in windows (windows 7), and reinstall it, windows will recognise that the printer is online, and talk to it. In all other cases, the windows and mac computers (purchased last week, running whatever is the latest and greatest mac os) in my household will simply not recognise that the printer is online. The printer is statically configured to use the same IP address, so that's not an issue. Because the printer works just fine with windows after delete and re-add, I assume that the issue with the mac is that I haven't installed whatever drivers Macs need to talk to Canon printers over a network.

  Read the article

• Hyper-V networking....still not sure which way to go??

  - by CZhale

  We have our Hyper-V server up and running (Windows 2008 ENT SP2) and started to create some of our VMs. The server has 4 total nics. 2 onboard Broadcom 1gb nic cards and a pci dual port Intel Pro cards 1gb. Right now, I have setup 1 broadcom nic to be the hyper-v host nic, and setup the other broadcom nic for the VMs. We are not using the Intel Nics....should we be thinking about teaming?Link Aggregation?? I just want to achieve the best possible setup for the network, but have read many things for and against teaming the nics?? Thoughts?

  Read the article

• Can a Linksys Router be the cause of bad speeds on a 1.5 mbps link.

  - by gramware

  We use a Linksys 5-port router at a smal organization with about 20 employees. We recently acquired a 1.5 mbps fibre link, but sometimes the link goes down and speeds are still low. On enquirey from the ISP, this was part of the response, However there maybe throttling due to the router in place. A Linksys is a low end router and may be unable to carried traffic of up to 1536Kbps. We are in a position to deploy a Cisco 871 router on test for 2 wks to eliminate that possibility. Also kindly advise the destination of the ping results they look to high. How true is that about the router throttling the network and need for a bigger one.

  Read the article

• tacacs integration with database

  - by chingupt

  We are setting up TACACS+ in our network which is a mix of Cisco AP's and other brands. However we have a centralized managemnet system which allows our customers to centrally configure services. Hence we would like to setup a tacacs+ server integrated with some database. Can this be done? I found the following package at www.shrubbery.net/tac_plus/ but it does not have the necessary plugins for database. Please let me know how to go about this. TIA Sachin

  Read the article

• assign auto static ip on ubuntu 10.04

  - by ronakin

  I'm trying to set auto static ip. I've set the content of /etc/network/interfaces to be: auto lo auto eth0 iface eth0 inet static address 192.168.1.2 netmask 255.255.255.0 gateway 192.168.1.1. and /etc/resolv.conf to be: nameserver 192.168.1.1. It seems that the ip address have set successfully. However, when I plug out the lan cable and then plug it back, the ip address is not set. How can I make it automatically set the static ip when the lan cable is connected?

  Read the article

• VPN Connected, How to browse files? Windows Vista

  - by Wbdvlpr

  I am trying to establish a VPN connection to a server in my office from my laptop at home. I tried some of the steps as mentioned here: Connect to a network Connect to a workplace Use my Internet Connection (VPN) Then type server IP address and then my username & password. After creating a VPN connection, I can see I am connected to it. Now I want to browse files on the server. But I have no clue where I should look for them. I was thinking more of a simple step, like, Windows Run > Type ip address > \\124.345.678.900, then a prompt asking username and password, and finally a window opens to view the files. I tried to google it, but still unable to view files. Please help. Update: I didn't mention that when I try to connect to server via \\124.345.678.900 I get 0x80070043 error message.

  Read the article

• How to share files and folders on a forum so that anyone can download without having an Ubuntu One account?

  - by ashok.biollay

  I just began to discover Ubuntu One. I upload a video on my account, and put it in a folder. I would like to know whether it is possible to share this folder or this file simply by giving the url in forum (in a message), so that anyone can download the file, with no need to have an Ubuntu One account. (a bit like PhotoBucket, where you can share pictures and videos and folders to people with ou without PhotoBucket, and anyone can download them) Thank you in advance for your answers.

  Read the article

• IP Tunneling for Spotify? [closed]

  - by everwicked

  I was in the UK and enjoyed Spotify relentlessly. Now I've moved back to Greece and I can't even pay for the darn thing. So my idea was this- I have a server in France and it has a fail-over IP in the UK. So I installed a proxy server on it and made it listen to the UK IP. So far so good. Then, I played Spotify for a while through the proxy server just fine, and it thought I was in the UK. But now... it gives me an error message that I'm in another country than the one on my profile (UK). I don't really understand why - maybe they also geolocate the IP address of the client, not just the proxy server? Either way, I'm kinda stuck - is there a way to tunnel Spotify's network traffic through my server transparently? Maybe a VPN or something similar? Thanks

  Read the article

• Windows 7 add printer, cancelled, but port still in use. How to remove?

  - by Jake

  I tried to add a network printer at www.xxx.yyy.zzz, but halfway it when it asked for a driver, I cancelled it because I do not have the driver at hand. Later when I try to add again, it tells me the port (www.xxx.yyy.zzz), which is automatically specified as the same as the IP for the printer, is already in use and then suggest www.xxx.yyy.zzz_1 Now, I cannot find the www.xxx.yyy.zzz printer anywhere such that I can remove it and use back the same port. How should I do it? Any ideas? Thanks.

  Read the article

• Why are there unknown URLs in router log?

  - by Martin

  I recently looked at my router log. Why are a lot of requests that I don't send originated from a computer in my home network? They do not look like 3rd-party advertisements / images embedded in a page. The request have patterns, such as: top-visitor.com/look.php www.dottip.com/search/result.php?aff=8755&req=nickelodeon+games www.placeca.com/search/result.php?aff=3778&req=wireless+cell+phone www.bb5a.com/search.php?username=3348&keywords=flights www.blazerbox.com/search.php?username=2341&keywords=colorado+springs+real+estate www.freeautosource.com/search.php?username=sun100&keywords=vehicle www.1sp2.com/search.php?username=20190&keywords=las+the+hotel+vegas www.loadgeo.com/search/result.php?aff=10357&req=winamp www.exalt123.com/portal.php?ref=seo2007 www.7catalogs.com/search.php?username=la24&keywords=shutter www.theloaninstitute.com/search.php?username=kevin&keywords=webcam www.grammt.com/search.php?username=2530&keywords=bob And there are hundreds of these requests send within a second. So what's happening?

  Read the article

• unusual webpage access problem

  - by user28163

  This is one of the weirdest problems I've ever seen and I'm out of ideas. I cannot access a couple of websites from my home pc (for 3-4 days now), or at least they go really really slow ~700b/s I can access these same websites fine from my laptop from same IP address. - The websites originate from different countries and are huge popular sites. - I have tried both my PC's network cards. - I have reformatted my PC. - I have reset my router to factory settings. - I have created virtual computers on my PC, and from inside those I cannot access the webpages. - I have flushed my dns. - I tried specifying my dns server addresses to 8.8.8.8 and 8.8.4.4. I can only access the webpages using my PC, if I first connect to an outside VPN. Again, these sites work fine on the 2 other pcs in this house (same ISP and internet connection). help plz :)

  Read the article

• PacketFence Installation?

  - by Charles Miton

  So I've stumbled across PacketFence during my search for a decent Network Access Control system. After doing a little research about it's capabilities I've come to realize it's meets all the requirements that I was looking for. Unfortunately, being primarily a MS Administrator, I'm having many issues trying to successfully getting it up and running. Is there anyone or any place that has a step-by-step tutorial on how to do this? I love the prospect of using Open Source software, but need some help jumping this particular hurdle. I'm trying to use CentOS for the OS but I'm open to alternatives if thats what it takes to get this system up and running.

  Read the article

• Computer prints blank pages before and after content

  - by Cpt. Jack

  This would seem like a pretty simple question but I have exhausted every idea I can come up with. I bought a brand new Dell Latitude E5410 not too long ago with Windows 7 OS. I installed office 2010 on the machine right away and have had a printing problem since day one. For some reason every time I print a page, a blank page prints out before and after the content print. This also applies to any other application such as notepad or printing an email. If I have a 6 page document, it still prints out one page before and after every content page. Meaning I get my 6 page document along with 12 blank pages. I can't figure out why this would be some sort of default setting or what would cause this printing configuration. I am the only computer on the network that has this problem and quite frankly I'm getting tired of it. Can anyone help me figure this out or steer me in the right direction to correcting this problem?

  Read the article

• Is there software that lets me drag windows between two PCs? (there is!)

  - by Jonathan

  I'm looking for a preferably free program that is similar to MaxiVista, which lets you extend you desktop to another desktops screen on the same network. But with MaxiVista you have to extend the entire screen. I'd like to just drag one window onto the other computers screen without extending the desktop. So on top of the other computer's windows. Kind of like a cross between MaxiVista and Windows 7' XP mode where you can run XP programs on the windows 7 desktop. EDIT: I am pleased to announce this is possible, though the windows is poor quality (8-bit color) but I believe thats just because MetaVNC isn't very up to date.

  Read the article

< Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >