Search Results

Search found 4516 results on 181 pages for 'vincent low'.

Page 134/181 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >

• Format & Fresh Install Mac OS X Snow Leopard on Mac mini.

  - by sagar

  Hello Every one. I have purchased a DVD of Snow Leopard (Mac OS X 10.6.2) I purchased a Mac mini with Leopard (Mac OS X 10.5.7) I tried to install Mac OS X 10.6.2 Everything went perfectly. System was installed successfully. But the problem that I faced is as follows. System was installed but my older data remained as it is. (means installation didn't format every thing - means installation was done on upgrade basis.) Now, my system works with very low speed. Previous performance of Mac mini was double as compare to current upgrade version. Now - my question are as follows. Does an upgrade installation causes the performance issues in Mac OS X? Or is Snow Leopard too demanding for the Mac mini? ( 2 Ghz Intel Core 2 Duo, 1GB RAM - is this configuration OK for Snow Leopard? ) Does a fresh install work better than an upgrade?

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• How to configure mod_proxy_balancer to gracefully fail under high load

  - by bramp

  We have a system which has one Apache instance in front of multiple tomcats. These tomcats then connect to various databases. We balance the load to the tomcat with mod_proxy_balancer. Currently we are receiving 100 requests a second, the load on the Apache server is quite low, but due to database heavy operations on the tomcats, the load there is roughly 25% (of what I estimate they can handle). In a few weeks there is an event happening and we estimate that our requests will jump significant, maybe by a factor of 10. I'm doing everything I can do reduce the load on our tomcats, but I know we are going to run out of capacity, so I would like to fail gracefully. By this I mean, instead of trying to deal with too many connections which all timeout, I would like Apache to somehow monitor average response time, and as soon as the response time to Tomcat is getting above some threshold, I would like a error page displayed. This means that users who are lucky still get a page rendered quickly, and those who are unlucky get a error page quickly. Instead of everyone waiting far too long for their page, and eventually everyone timing out, and the database being swamped with queries which are never used. Hopefully this makes sense, so I was looking for suggestions on how I could achieve this. thanks

  Read the article

• Server load high, CPU idle. NFS the cause?

  - by Mech Software

  I am running into a scenario where I'm seeing a high server load (sometimes upwards of 20 or 30) and a very low CPU usage (98% idle). I'm wondering if these wait states are coming as part of an NFS filesystem connection. Here is what I see in VMStat procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 1 0 1298784 0 0 0 0 16 5 0 9 1 1 97 2 0 0 1 0 1308016 0 0 0 0 0 0 0 3882 4 3 80 13 0 0 1 0 1307960 0 0 0 0 120 0 0 2960 0 0 88 12 0 0 1 0 1295868 0 0 0 0 4 0 0 4235 1 2 84 13 0 6 0 0 1292740 0 0 0 0 0 0 0 5003 1 1 98 0 0 4 0 0 1300860 0 0 0 0 0 120 0 11194 4 3 93 0 0 4 1 0 1304576 0 0 0 0 240 0 0 11259 4 3 88 6 0 3 1 0 1298952 0 0 0 0 0 0 0 9268 7 5 70 19 0 3 1 0 1303740 0 0 0 0 88 8 0 8088 4 3 81 13 0 5 0 0 1304052 0 0 0 0 0 0 0 6348 4 4 93 0 0 0 0 0 1307952 0 0 0 0 0 0 0 7366 5 4 91 0 0 0 0 0 1307744 0 0 0 0 0 0 0 3201 0 0 100 0 0 4 0 0 1294644 0 0 0 0 0 0 0 5514 1 2 97 0 0 3 0 0 1301272 0 0 0 0 0 0 0 11508 4 3 93 0 0 3 0 0 1307788 0 0 0 0 0 0 0 11822 5 3 92 0 0 From what I can tell when the IO goes up the waits go up. Could NFS be the cause here or should I be worried about something else? This is a VPS box on a fiber channel SAN. I'd think the bottleneck wouldn't be the SAN. Comments?

  Read the article

• Apahe configuration with virtual hosts and SSL on a local network

  - by Petah

  I'm trying to setup my local Apache configuration like so: http://localhost/ should serve ~/ http://development.somedomain.co.nz/ should serve ~/sites/development.somedomain.co.nz/ https://development.assldomain.co.nz/ should serve ~/sites/development.assldomain.co.nz/ I only want to allow connections from our local network (192.168.1.* range) and myself (127.0.0.1). I have setup my hosts file with: 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 127.0.0.1 development.somedomain.co.nz 127.0.0.1 development.assldomain.co.nz 127.0.0.1 development.anunuseddomain.co.nz My Apache configuration looks like: Listen 80 NameVirtualHost *:80 <VirtualHost development.somedomain.co.nz:80> ServerName development.somedomain.co.nz DocumentRoot "~/sites/development.somedomain.co.nz" DirectoryIndex index.php <Directory ~/sites/development.somedomain.co.nz> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost localhost:80> DocumentRoot "~/" ServerName localhost <Directory "~/"> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <IfModule mod_ssl.c> Listen *:443 NameVirtualHost *:443 AcceptMutex flock <VirtualHost development.assldomain.co.nz:443> ServerName development.assldomain.co.nz DocumentRoot "~/sites/development.assldomain.co.nz" DirectoryIndex index.php SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile /Applications/XAMPP/etc/ssl.crt/server.crt SSLCertificateKeyFile /Applications/XAMPP/etc/ssl.key/server.key BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 <Directory ~/sites/development.assldomain.co.nz> SSLRequireSSL Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> </IfModule> http://development.somedomain.co.nz/ http://localhost/ and https://development.assldomain.co.nz/ work fine. The problem is when I request http://development.anunuseddomain.co.nz/ or http://development.assldomain.co.nz/ it responds with the same as http://development.somedomain.co.nz/ I want it to deny all requests that do not match a virtual host server name and all requests to a https host that are requested with http PS I'm running XAMPP on Mac OS X 10.5.8

  Read the article

• Abysmal transfer speeds on gigabit network

  - by Vegard Larsen

  I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

  Read the article

• Reduce power consumption of gaming computer while idle

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 clocked @ 3.3 Ghz 3x DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 oc'd at 800/1600/1850 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) I've already seen this post Reduce power use on computer and this post How do I lower power consumption of my computer and while useful, I'm looking for answers specific to my build and OS. I'm pretty sure this build is a energy-intensive build by default, but I want to try to reduce the amount of energy my build uses when I leave it idle (when I go to bed or go out, etc). The first requirement for this machine is that I need to leave it on, so I cannot turn it off while it's being unused. I run it as a file server for personal reasons and I also leave it on in case people leave me messages on various IM services and chat clients (IRC, MSN, Steam, XFire, Pidgin, etc). I'm also unable to replace the parts in my computer with a cheaper "greener" part. What are some ways to minimize the amount of power the machine uses? I'm already using a high efficiency power supply (80 Plus Gold), but I imagine there's other things that can be done in the BIOS and Windows' power settings to reduce power usage while I'm not using the computer. From what I can tell, I can't use Sleep since that'll disable network access (whole reason why I leave the computer on in the first place). I already turn off my monitor when it's not in use. I enabled Intel SpeedStep within the BIOS (I know, I have a 965 and why am I enabling SpeedStep?) Should I bring the graphics card back to stock speeds and lower the clock on the processor even more? Main reason why I'm asking is I think this computer alone is the reason why my power bill is high, so I want to reduce its consumption to as low as possible without having to shut the thing down.

  Read the article

• PhpMyAdmin Missing parameter:

  - by Ali

  Everything was working fine until this moment I want to create a new database and I'm receiving this error db_create.php: Missing parameter: new_db (FAQ 2.8) Also when I was trying to export my database I also receive the following error export.php: Missing parameter: what (FAQ 2.8) export.php: Missing parameter: export_type (FAQ 2.8) When I looked it FAQ 2.8 from the suggested link in PHPMYADMIN 2.8 I get "Missing parameters" errors, what can I do? Here are a few points to check: In config.inc.php, try to leave the $cfg['PmaAbsoluteUri'] directive empty. See also FAQ 4.7. Maybe you have a broken PHP installation or you need to upgrade your Zend Optimizer. See http://bugs.php.net/bug.php?id=31134. If you are using Hardened PHP with the ini directive varfilter.max_request_variables set to the default (200) or another low value, you could get this error if your table has a high number of columns. Adjust this setting accordingly. (Thanks to Klaus Dorninger for the hint). In the php.ini directive arg_separator.input, a value of ";" will cause this error. Replace it with "&;". If you are using Hardened-PHP, you might want to increase request limits. The directory specified in the php.ini directive session.save_path does not exist or is read-only. I did tried with php.ini to make sure that I've session.save_path = "/tmp" I'm using Mac Xserver and running with MAMP I did tried everything to restart my server and nothing help. Please if anyone help me to give me some suggestion. Apologize if I post in a wrong place.

  Read the article

• ASP.NET sending email through exchange problem

  - by Solmead

  I have an exchange 2010 server running on Windows 2008 R2, I also have a remote webserver running Windows 2003 with multiple sites on it (all asp.net mvc 2 sites). I setup a Transport in exchange and all the websites on my remote web server can send email no problem to anyone in the exchange server and to any external domain. Now for my problem. I am having issues with that webserver, so I moved one of the websites to run on my exchange server, it runs well (low hit website) except that email doesn't work from that site. I tried changing the Transport in exchange to add the IP address of the local machine and the 127.0.0.1 addresses and it still isn't sending any email. Any ideas on how to get this working? The remote websites can still send email no problem, the version of the site that I had to move on the remote server can still email, but on the exchange server for that website email does not send. I would guess it is a Transport issue, since it is running on the same server a firewall shouldn't be the issue. I changed the smtp setting in web.config to localhost, and now I do receive email to my account on the exchange server, but I do not receive any emails on outside addresses. To add more description, this is a custom developed asp.net mvc 2 website. And no errors were being generated in the code when sending the email in either case.

  Read the article

• Ubuntu Device-mapper seems to be invincible!

  - by Andrew Bolster

  I'm working on a hopefully unrelated question question and I've got to a strange situation. First: I know very little about the very low level hardware kernal storage driver magix, so I'm hoping a) someone can help and b) someone can explain it to me better. I've been trying a dozen different configurations of my 2x500GB SATA drives over the past few hours involving switching between ACHI/IDE/RAID in my bios; After each attempt I've reset the bios option, booted into a live CD, deleting partitions and rewriting partition tables left on the drives. Now, however, I've been sitting with a /dev/mapper/nvidia_XXXXXXX1 that seems to be impossible to kill! its the only 'partition' that i see in the Ubuntu install (but I can see the others in parted) but it is only the size of one of the drives, and I know I did not set any RAID levels other than RAID0. Anyone have any ideas how I can kill this and get back to just two independent IDE drives? Or can anyone convince me of a reason to go the AHCI route? Many thanks in advance.

  Read the article

• Git fails to push with error 'out of memory'

  - by jwir3

  I'm using gitosis on a server that has a low amount of memory, specifically around 512 MB. When I try to push a large folder (happens to be a backup from an android phone), I get: me@corellia:~/Configs/$ git push origin master Counting objects: 18, done. Delta compression using up to 8 threads. Compressing objects: 100% (14/14), done. fatal: Out of memory, malloc failed MiB | 685 KiB/s error: pack-objects died of signal 13 error: failed to push some refs to 'git@dagobah:Configs' I've been searching the web, and notably found: http://www.mail-archive.com/[email protected]/msg01747.html as well as http://git.661346.n2.nabble.com/Out-of-memory-error-during-git-push-td5443705.html but these don't seem to help me for two reasons: 1) I am not actually out of memory when I push. When I run 'top' during the push, I get: 24262 git 18 0 16204 6084 1096 S 2 1.2 0:00.12 git-unpack-obje Also, during the push if I run /head/meminfo, I get: MemTotal: 524288 kB MemFree: 289408 kB Buffers: 0 kB Cached: 0 kB SwapCached: 0 kB Active: 0 kB Inactive: 0 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 524288 kB So, it seems that I have enough memory free, but it's actually still failing, and I'm not enough of a git guru to figure out what is happening. I would appreciate it if someone could give me a hand here and tell me what could be causing this problem, and what I can do to solve it. Thanks! EDIT: The output of running the ulimit -a command: scottj@dagobah:~$ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 204800 max locked memory (kbytes, -l) 32 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 10240 cpu time (seconds, -t) unlimited max user processes (-u) 204800 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited

  Read the article

• Formatting an external HDD stuck at 70%

  - by mahmood

  My external HDD which is a 250GB WD (powered by USB) seems to have problem! Whenever i try to copy some files, it stuck while copying. I decided to format it. So I used windows tool and performed the format (not quickly) however at nearly 70% it stuck. Then I decided to perform a low level format with lowlevel. Again it stuck at 70%. I endup that the HDD has bad sector. So is there any tool that mark the bad sectors and bypass them? It is not very reasonable to through 250GB because of some bad sectors! P.S: I saw a similar topic but there were no conclusion there either. The smart data is Attribute, raw value, value, threshold, status Read Error Rate, 50, 200, 51, OK Spin-Up Time, 3275, 154, 21, OK Start/Stop Count, 2729, 98, 0, OK Reallocated Sectors Count,0, 200, 140, OK Seek Error Rate, 0, 100, 51, OK Power-On Hours (POH), 1057, 99, 0, OK Spin Retry Count, 0, 100, 51, OK Recalibration Retries ,0, 100, 51 , OK Power Cycle Count, 1385, 99, 0, OK Power-off Retract Count, 425, 200, 0, OK Load /Unload Cycle Count,12974, 196, 0, OK Temperature, 43, 43, 0, OK Reallocation Event Count,0, 200, 0, OK Current Pending Sector Count,23,200, 0, Degradation Uncorrectable Sector Count, 0, 100, 0, OK UltraDMA CRC Error Count,6, 200, 0, OK Write Error Rate/Multi-Zone Error Rate,0,100,51, OK It seems that the most important thing is this line Current Pending Sector Count,23,200, 0, Degradation Any idea on that?

  Read the article

• How to run the CPU at something like 75%?

  - by Tobias Kienzler

  My notebook is too old for me to invest into a new fan (it will simply be replaced by a new one when the final heat death occurs), but when it runs on full speed I feel like sitting in front of a vacuum cleaner with integrated cooking... I'm currently using NHC, the Max Battery mode of which let's the CPU run at 50% (~800 MHz). That's fine for most applications, and both temperature and noise remain low. However, on some occasions I need a bit more speed, more around 75% maybe. Can I set the power saving settings somehow so that the CPU won't surpass 75% of it's capability so that an acceptable compromise between power and noise is achieved? I can't set the CPU frequency in the BIOS and since on rare occasions I'd like to be able to switch to 100% without much hassling, hardware solutions like setting jumpers are no option. This answer to a similar (linux!) question mentions NHC should be able to offer these options, but for me they are all greyed out: The notebook is an Asus Z9200K, I guess NHC doesn't support its chipset enough for these advanced options.

  Read the article

• SQL Server 2008 second instance times out when logging in -- but only the first time?

  - by Kromey

  This is a strange one that has plagued me for a while now. When logging in to the second instance of SQL Server 2008 on one of our database servers, we get a timeout error: Cannot connect to servername\mssqlserver2. Additional information: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft SQL Server)") (This is the error message when trying to connect with Microsoft SQL Server Management Studio; other tools experience the same error, but of course say it in different ways.) Immediately re-attempting to log in works just fine, so whatever the cause it's ephemeral! This happens regardless of user or authentication type (both Windows and SQL Server authentication methods are supported on this instance). What's even weirder, though, is that the first instance on this server has never once demonstrated this problem. Server is a Windows Server 2008 R2 virtual server, hosted in Microsoft Hyper-V (host is likewise Server 2008 R2). The server has 2GB of RAM, and seems to regularly be using 90% of that -- could low memory be the cause of this issue? I could see this second instance -- which is not used very often yet -- being swapped out to disk, and then taking too long to load back into memory to respond in time to the connection request, but I'd rather have more than just my own hunch before I go scheduling a downtime for this server (the first instance is used regularly) and then just throwing extra resources at it in the blind hope that the problem goes away.

  Read the article

• CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

  - by ewwhite

  Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

  Read the article

• Home media storage solution

  - by Dan

  I record lots of personal HD film footage and am looking for a cheap way to store all of this. I take ~120 GB of footage each month, so something expandable would be nice... something that might be able to hold 6+ SATA drives. There is a low load requirement, as there is never more than a user or two... but it should be able to keep up with streaming 2 simultanious HD videos. I don't really want to spend more than $200-$300 on top of the $900 I am thinking of spending for 6X2GB SATA drives@ $150 apiece, but I am willing to pay extra for a quality solution. Should I get a cheap NAS server? a cheap multi-drive external enclosure? should I just get some used systems off craigslist? If it is an independent system I'll probably just throw ubuntu on it since I can maintain that well. Its easy to do a software raid from ubuntu too, if I choose to go that way. Thanks

  Read the article

• Apache + PHP via FastCGI

  - by Wilco

  I'm running into some problems while attempting to run PHP via FastCGI in Apache. I have the FastCGI module loaded, but get the following error when attempting to load a page: The requested URL /fastcgi/php54.fcgi/index.php was not found on this server. Somewhere, it seems that the script to be executed is appended to the executable without any spaces. Is this where the problem likely is? Below I've included snippets from my Apache configuration (hopefully this is enough): LoadModule fastcgi_module libexec/apache2/mod_fastcgi.so FastCgiIpcDir /var/run/fastcgi AddHandler fastcgi-script .fcgi FastCgiConfig -autoUpdate -singleThreshold 100 -killInterval 300 AddType application/x-httpd-php .php ScriptAlias /fastcgi/ /Library/WebServer/FCGI-Executables/ <Directory "/Library/WebServer/FCGI-Executables"> Options +ExecCGI SetHandler fastcgi-script Order allow,deny Allow from all <VirtualHost *:80> ServerName www.somedomain.com ServerAdmin [email protected] DocumentRoot "/Web/www.somedomain.com" DirectoryIndex index.html index.php default.html CustomLog /var/log/apache2/access_log combinedvhost ErrorLog /var/log/apache2/error_log Action application/x-httpd-php /fastcgi/php54.fcgi <IfModule mod_ssl.c> SSLEngine Off SSLCipherSuite "ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:+MEDIUM" SSLProtocol -ALL +SSLv3 +TLSv1 SSLProxyEngine On SSLProxyProtocol -ALL +SSLv3 +TLSv1 </IfModule> <Directory "/Web/www.somedomain.com"> Options All -Indexes +ExecCGI +Includes +MultiViews AllowOverride All <IfModule mod_dav.c> DAV Off </IfModule> <IfDefine !WEBSERVICE_ON> Deny from all ErrorDocument 403 /customerror/websitesoff403.html </IfDefine> </Directory> </VirtualHost> ... and this is the executable: #!/bin/sh PHP_FCGI_CHILDREN=1 PHP_FCGI_MAX_REQUESTS=5000 export PHP_FCGI_CHILDREN export PHP_FCGI_MAX_REQUESTS exec /opt/local/bin/php-cgi54

  Read the article

• SSRS2008R2 report times out, but the underlying query executes in the Management Studio

  - by Matthew Belk

  A customer of mine recently moved servers and the new server has SQL2008R2. His old server was SQL2005. The new server has substantially better CPU, RAM, and disk performance than the old, but several reports time out while executing. When I run the underlying query in the SQL Management Studio, the query executes in sub-second time. The exact error message returned via the Report Manager UI is: An error occurred within the report server database. This may be due to a connection failure, timeout or low disk condition within the database. (rsReportServerDatabaseError) Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. It must be noted that this database is not just analytical; it's also fairly transactional, although the transaction volume is not exceptionally high. What can I do to improve the performance of the SSRS query engine? Are there settings in the data source I can adjust, or in the SSRS config files?

  Read the article

• Windows XP over two monitors, but one of them switches off at boot... how to fix? How to switch bac

  - by jae

  When booting into XP (x64, Athlon II X2 245, 4GB RAM), my main monitor (got two 19" TFTs hooked up, two gfx cards, a 4650 (1GB, the primary monitor's on this) and a 4350 (512MB)) switches off. Logging in blind (cursor down key, typing password) gets me one screen, the secondary. Booted correctly until about two days ago. No clue what's the cause, last change was (if I don't overlook something) installing the ATI 9-12 hotfix. And booting into Windows 7, after returning from 7, it was like this. For some weird reason, I cannot start Catalyst Control Center (I right-click desktop, choose the CCC entry, the pointer changes to hourglass for a half-second... and nothing. Likewise with "Properties"... I think, as all windows open on the primary (off) screen, and no entry appears in the task bar for Properties) Completely stumped. Windows 7, same setup, works w/o a hitch. The primary monitor appears to run in some unknown, but pretty low, resolution, as the mouse pointer only moves onto it at about half-height. But, w/o CCC or display properties, I cannot check. And, obviously, not change anything. Hope this was not too long-winded. And I'm sure I still forgot essential stuff. :P

  Read the article

• Java web app deployment and ControlTier adoption

  - by Ran

  I've been searching for a configuration and deployment manager tool for my java-linux based web service and have been looking mainly at ControlTier (http://controltier.org). We operate at a medium scale (100's of hosts, multi-DC, dozens of services). There seem to be be plenty of lower level system admin tools such as chef, puppet, cfengine, bcfg2 and more and my understanding and the reason I'm calling them "low level" is that they are great for system level administration tasks such as setting up a mount, file permissions, users etc but aren't designed, for example for java deployments, which usually come with a build process and special java semantics. In many cases any tool can be used to do anything but if it was not designed for the task it can get uncomfortable. OTOH control-tier seem to have been designed just for that - java application deployments, at least that's what all the tutorials on their site demonstrate but here's the problem - The wiki at http://controltier.org/wiki/ is pretty good and stuffed with examples and the company behind the open source CT product is very responsive (pushy...) however, I'm yet to have seen any material from 3rd party users on the net. No success stories, no detailed blog posts, no best practices, no cheat sheets, not even hate letters, nothing. This plays badly for DTO solutions, CT's sponsor for two reasons, one is that it makes me suspicious what's the reason for the poor adoption? and second, what do I do if I get stuck and there's no help page on CT's wiki page and the mailing list is too slow to answer. I'm stuck with a "free" product that a consultancy company is pushing. So my question here - I'd be interested in hearing if anyone has had real world experience with CT for java based web app deployments and if he'd thumb up the product? Any other comments that may enlighten me are welcome of course...

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• Firewall for internal networks

  - by Cylindric

  I have a virtualised infrastructure here, with separated networks (some physically, some just by VLAN) for iSCSI traffic, VMware management traffic, production traffic, etc. The recommendations are of course to not allow access from the LAN to the iSCSI network for example, for obvious security and performance reasons, and same between DMZ/LAN, etc. The problem I have is that in reality, some services do need access across the networks from time to time: System monitoring server needs to see the ESX hosts and the SAN for SNMP VSphere guest console access needs direct access to the ESX host the VM is running on VMware Converter wants access to the ESX host the VM will be created on The SAN email notification system wants access to our mail server Rather than wildly opening up the entire network, I'd like to place a firewall spanning these networks, so I can allow just the access required For example: SAN SMTP Server for email Management SAN for monitoring via SNMP Management ESX for monitoring via SNMP Target Server ESX for VMConverter Can someone recommend a free firewall that will allow this kind of thing without too much low-level tinkering of config files? I've used products such as IPcop before, and it seems to be possible to achieve this using that product if I re-purpose their ideas of "WAN", "WLAN" (the red/green/orange/blue interfaces), but was wondering if there were any other accepted products for this sort of thing. Thanks.

  Read the article

• Performance experiences for running Windows 7 on a Thin-Client?

  - by Peter Bernier

  Has anyone else tried installing Windows 7 on thin-client hardware? I'd be very interested to hear about other people's experiences and what sort of hardware tweaks they had to do to get it to work. (Yes, I realize this is completely unsupported.. half the fun of playing with machines and beta/RC versions is trying out unsupported scenarios. :) ) I managed to get Windows 7 installed on a modified Wyse 9450 Thin-Client and while the performance isn't great, it is usable, particularly as an RDP workstation. Before installing 7, I added another 256Mb of ram (512 total), a 60G laptop hard-drive and a PCI videocard to the 9450 (this was in order to increase the supported screen resolution). I basically did this in order to see whether or not it was possible to get 7 installed on such minimal hardware, and see what the performance would be. For a 550Mhz processor, I was reasonably impressed. I've been using the machine for RDP for the last couple of days and it actually seems slightly snappier than the default Windows XP embedded install (although this is more likely the result of the extra hardware). I'll be running some more tests later on as I'm curious to see particularl whether the streaming video performance will improve. I'd love to hear about anyone's experiences getting 7 to work on extremely low-powered hardware. Particularly any sort of tweaks that you've discovered in order to increase performance..

  Read the article

• Windows Server task manager displays much higher memory use than sum of all processes' working set s

  - by Sleepless

  I have a 16 GB Windows Server 2008 x64 machine mostly running SQL Server 2008. The free memory as seen in Task Manager is very low (128 MB at the moment), i.e. about 15.7 GB are used. So far, so good. Now when I try to narrow down the process(es) using the most memory I get confused: None of the processes have more than 200MB Working Set Size as displayed in the 'Processes' tab of Task Manager. Well, maybe the Working Set Size isn't the relevant counter? To figure that out I used a PowerShell command [1] to sum up each individual property of the process object in sort of a brute force approach - surely one of them must add up to the 15.7 GB, right? Turns out none of them does, with the closest being VirtualMemorySize (around 12.7 GB) and PeakVirtualMemorySize (around 14.7 GB). WTF? To put it another way: Which of the numerous memory related process information is the "correct" one, i.e. counts towards the server's physical memory as displayed in the Task Manager's 'Performance' tab? Thank you all! [1] $erroractionpreference="silentlycontinue"; get-process | gm | where-object {$.membertype -eq "Property"} | foreach-object {$.name; (get-process | measure-object -sum $_.name ).sum / 1MB}

  Read the article

• Minimum specs needed to run 1080p HD movies?

  - by Wesley

  Hi all, I was wondering how low you could go with hardware that would still be able to smoothly run HD movies. My current plan is around $215 CAD w/o a hard drive: Intel Pentium 4 @ 3.2 GHz - 1GB DDR/SDRAM - 512MB X1600 Pro AGP - 350W PSU - ECS P4VXASD2+ - Bluray/DVD-RW drive. As for the hard drive, could I just get a 7200RPM IDE HDD? Also, I'm planning on installing XP Pro SP3, unless Ubuntu somehow has an advantage. I'm not wanting this to be a media center only computer... just want it to be a normal computer with just enough oomph to play HD movies. Thanks in advance. EDIT1: Forgot to mention that the Bluray/DVD-RW drive is SATA, but I was planning on getting an SATA-IDE adapter or a PCI card with SATA. EDIT2: Oh yes... if I get a PCI card with SATA, would you then recommend I use an SATA hard drive as well? That would leave all the IDE ports on the motherboard unused... is that a good idea?

  Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >