Search Results

Search found 4516 results on 181 pages for 'vincent low'.

Page 136/181 | < Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >

• Only half of RAM is recognized by BIOS

  - by Rick Crawford

  I got a Gigabyte GA-P35-DS3 mainboard. Some time ago I noticed that Windows only showed 2GB instead of 4GB. I don't know exactly what caused it anyway. I tried putting in each of the 4 x 1GB RAM modules one by one, and tried every slot one by one, until every stick and slot worked. However, then I tried adding one more at a time, and it kept showing 1GB, until I put in all 4, where it only showed 2 GB instead of 4 (in BIOS and windows 7 64bit). I tried replacing the BIOS battery since I've read that low battery could cause it. It didn't help though. I also bought 4GB new RAM (yes, it's supported, I checked it), and it's still the same, it only shows 2GB (or 3GB, when I put in 4 of the new and 2 of the old). I also did the latest BIOS update, and used default BIOS settings, but nothing of that helped. When my PC boots it shows "RAM modules used 2 and 3", when 4 sticks are in - or "0 and 1", when only 2 are in.

  Read the article

• Data Store/Volume disconnecting. How to resume copy of VMDK?

  - by Serge

  I'm having an issue with my ESXi 4.1 hosts losing the datastore with FC SAN after a power outage. All 3 hosts disconnect so it's definitely a SAN issue. I've tried to resolve the issue on the SAN side with the SAN software support and Adaptec hardware support. No luck there. So I'm stuck with a SAN that will randomly disconnect the volume. I need to get the virtual machines (VMDK files) from the datastore. The problem is I can only get 5-20% before the data store disconnects. I have backups that are slightly older that I can use to replicate the VMDK differences to. What has not worked so far: Powering up the VMs, will boot up for 5-15 minutes then freeze vCenter migrate or clone of VM, will fail after similar period of time vCenter copy/paste of VMDK. Was able to get one 30GB VMDK and no luck after that. vMware Data Recovery. Fails at low %, can't resume, so next backup starts from begining. Veeam Backup & Recovery. Same as above, no resume function. If I can just find a backup solution that will resume from the failed spot that would solve my issue. Anyone have any ideas that I could try? EDIT 1 The SAN is Open-E DSS 6 running on a Supermicro 24 drive enclosure with 4 port Qlogic FC. Adaptec 52445 RAID card.

  Read the article

• Windows Firewall Software to Filter Transit Traffic

  - by soonts

  I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

  Read the article

• What are the frequencies of current in computers' external peripheral cables and internal buses?

  - by Tim

  From Wikipedia, three different cases of current frequency are discussed along with the types of cables that are suitable for them: An Extra Ordinary electrical cables suffice to carry low frequency AC, such as mains power, which reverses direction 100 to 120 times per second (cycling 50 to 60 times per second). However, they cannot be used to carry currents in the radio frequency range or higher, which reverse direction millions to billions of times per second, because the energy tends to radiate off the cable as radio waves, causing power losses. Radio frequency currents also tend to reflect from discontinuities in the cable such as connectors, and travel back down the cable toward the source. These reflections act as bottlenecks, preventing the power from reaching the destination. Transmission lines use specialized construction such as precise conductor dimensions and spacing, and impedance matching, to carry electromagnetic signals with minimal reflections and power losses. Types of transmission line include ladder line, coaxial cable, dielectric slabs, stripline, optical fiber, and waveguides. The higher the frequency, the shorter are the waves in a transmission medium. Transmission lines must be used when the frequency is high enough that the wavelength of the waves begins to approach the length of the cable used. To conduct energy at frequencies above the radio range, such as millimeter waves, infrared, and light, the waves become much smaller than the dimensions of the structures used to guide them, so transmission line techniques become inadequate and the methods of optics are used. I wonder what the frequencies are for the currents in computers' external peripheral cables, such as Ethernet cable, USB cable, and in computers' internal buses? Are the cables also made specially for the frequencies? Thanks!

  Read the article

• CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

  - by Paul Cravey

  My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

  Read the article

• Can I trick Carbonite into backing up an external hard drive?

  - by Brian

  I use Carbonite to back up my PC (Windows XP). We were running low on disk space on our home PC (down to 15 GB), so I went out and purchased an external hard drive. However, Carbonite will not back it up. Is it possible to set up Carbonite to backup an external hard drive? I just want the external drive to be extra disk space. From their FAQ: The current version of Carbonite backs up only the files that reside on permanent hard drives on your computer. It will not back up network drives, external drives, and NAS (network accessed storage) drives. If there are files on a remote drive that you wish to include in your Carbonite backup, you should copy the files to a folder on your local hard drive. If the files are on a shared network drive, you could install Carbonite on the computer on which the network shared drive physically exists, and back the files up directly from that computer. Check back soon for a Carbonite service plan that will allow you to back up your external drives.

  Read the article

• Logitech QuickCam Pro 9000 & Windows 7 64-bit failing miserably

  - by Saxtus

  I am trying to install a Logitech QuickCam Pro 9000 webcam to Windows 7 64-bit. If I do it without using the Logitech drivers but instead the Windows Update ones, the camera works with low frame rate and without face tracking and all other bells and whistles that it's full driver provides. The moment I install the latest official Logitech driver, the problems begin: Camera works fine, until I decide to go to audio settings of the LWS panel or Windows'. Then LWS freezes and with it everything that tries to output audio. I am not able to open Playback/Recording devices window (it just doesn't appear) and system gets unstable and slow with LWS.EXE process not been able to close forcefully. If I reboot and forget the camera connected, this situation continues and system gets unstable from the beginning. If I reboot without the camera connected, everything works fine until I connect it and try to do something with audio settings of Windows or LWS panel. I should note, that until the freezing occurs, camera works as expected, with full frame rate, face tracking and everything that is expected to do. The soundcard is the ASUS SupremeFX II of the ASUS Striker II Extreme motherboard. Any ideas of what is causing this or what else to try so I can make it work as advertised? Thank you.

  Read the article

• Send keystrokes simultaneously to both host and slave over internet?

  - by donodarazao

  I would like to watch movies with a friend who lives far away from me. For this, the playback should be synchronized on both our pc. However, we have some constraints: Due to our low bandwidth internet, any form of streaming solution wouldn't work. We do however both have the same copy of the movie on our harddisks. We use movies to learn languages and because of this, we very frequently pause and rewind. The typical "3...2...1...go!" solution over skype wouldn't work because it would soon get out of sync. I imagine an approach that sends keystrokes simultaneously to both our pc would work (for example, if I press space to pause the movie at my pc, space should also be send to his pc). Any ideas how this could be realized? I looked into Synergy and InputDirector, but both neither seem to be an option, because I don't want to see the desktop of my friend, I want to see my desktop Keystrokes should be sent simultaneously to both pc, not just to one pc We have both Windows 7x64, and we might use any media player (VLC, XBMC,...).

  Read the article

• 100% CPU load on Ubuntu 10.04.3 LTS 64bit

  - by deadtired

  I have 2 days since I am trying to fix this issue, with no success. The server is a mysql database server. Hardware: DELL Poweredge 1950, 2x Intel Xeon Quad Core E5345 @ 2.33GHz, 16 Gb mem, 2x 146Gb SAS (software RAID1) Software: Ubuntu 10.04.3 LTS, MySQL 5.1.41 Issue: while mysql is not used and runs with no database, everything seems alright. As soon as I install a database, it has the reason to bring all 8 cores in 100% with low memory consumption. So, you can imagine the load average goes high (I saw 212 load average for the first time). The server doesn't become unresponsive, but you can see it's slow while browsing the project installed. Additional info: the database used is not more than 24MB and it was moved from a server with less resources and a lot more larger databases. So it's not the database/project. my.cnf is not a reason also, as I used both default one and the one I use on the same distribution on another server.What is interesting is that mysql doesn't close any process and runs to the limit of the max_connections. Logs are quiet. Nothing there. I switched to this Ubuntu version after I suspected some problems in the newly Ubuntu 11.10 server. This one worked alright for an hour after I made a kernel upgrade to 3.0.1 (it was using the memory also) I tested disk speed and seems alright. Some more output on the running server: dstat -cndymlp -N total -D total 3: htop command: Idea? Did anyone meet the same problem? Any fix you can think of?

  Read the article

• how to block spam email using Microsoft Outlook 2011 (Mac)?

  - by tim8691

  I'm using Microsoft Outlook 2011 for Mac and I'm getting so much spam I'm not sure how to control it. In the past, I always applied "Block Sender" and "Mark as Junk" to any spam email messages I received. This doesn't seem to be enough nowadays. Then I've started using Tools Rules to create rules based on subject, but the same spammer keeps changing subject lines, so this isn't working. I've been tracking the IP addresses they also seem to be changing with each email. Is there any key information I can use in the email to apply a rule to successfully place these spam emails in the junk folder? I'm using a "Low" level of junk email protection. The next higher level, "high", says it may eliminate valid emails, so I prefer not to use this option. There's maybe one or two spammers sending me emails, but the volume is very high now. I'm getting a variation of the following facebook email spam: Hi, Here's some activity you have missed. No matter how far away you are from friends and family, we can help you stay connected. Other people have asked to be your friend. Accept this invitation to see your previous friend requests Some variations on the subject line they've used include: Account Info Change Account Sender Mail Pending ticket notification Pending ticket status Support Center Support med center Pending Notification Reminder: Pending Notification How do people address this? Can it be done within Outlook or is it better to get a third party commercial software to plug-in or otherwise manage it? If so, why would the third party be better than Outlook's internal tools (e.g. what does it look for in the incoming email that Outlook doesn't look at)?

  Read the article

• In solaris, how monitor & auto-respond to critical events

  - by mamcx

  I have a website that randomly fail. Is running in open solaris on joyent. I have a monitoring service that alert me when the site is down, but, I want a way to put a "insider" tool that tell me why that happened. Is because the cpu is too high? Not memory? Which process fail? Is possible to have a backtrace of that? Everything is running on the Solaris Service Management Facility. The webserver is cherokee, the database is mysql and the language is python/django. I want the most simple setup to monitor that & auto-respond , ie: restart the webserver or the django process in case of failure. I prefer a low-overhead tool. I don't need the fancy monitoring that some tools have, no ned graphs or sms alert. Only know what fail, restart it if possible (maybe up to n times), and have a log somewhere when I will check it.

  Read the article

• Software/hardware to build video streaming server?

  - by Sasha Yanovets

  I am looking for a video streaming server solution, something like online TV server, with ability to make live broadcasts in the internet. What software could you recommend for that? What kind of hardware it should run on, should be there anything special? I am looking for a solution that could be scaled up to at least 1000 simultaneous users online with good resolution of video. I think it is good to have general answer on what direction to choose. But here more details on my specific case: I just looking for a solution almost from scratch. We have some video content that we've produced, but it is not delivered over internet yet. We do not tied to any particular vendor for now. We want to make 24 hours of steaming three 8 hour blocks with change of content every day. We want the ability to make regular live broadcasts. I guess we will need to have several options of streaming quality (low ~56 kb/s mid ~273 kb/s). Some terms just foreign to me (like play-truncation rate), if you could point out what parameters we should avare of, it would be great. Uplink to the internet is to be determined. We plan to start from something and scale up on the way. If you are already have some kind of media streaming server, just describe its configuration here (hardware, OS, software), peak number of concurrent users it serves. I think it could help people approaching this task.

  Read the article

• Asus K55VM usb 3.0 issue

  - by user2141481

  Good day superusers! I own the above laptop and I found out that there are some unknown and unusual issues with usb 3.0 ports. I haven't noticed anything strange until now. I got a new toshiba usb 3.0 external hdd and when I try to copy larger amount of data from my disk to the external hdd, the OS(windows 7) randomly starts ignoring the external hdd. It doesn't shut it down, it kinda just stops responding but the light on the hdd is still lit. I get an error that the files cannot be copied. I have reinstalled windows 7, installed all drivers(including intel chipset drivers of course) and the issue is still present. It acts normal when copying small amount of data. Also, I heard that some intel chipsets have an issue with usb, something about the connectors not transferring power when the usb device enters some kind of "low power mode" causing the device to stop responding and you need to plug it out and in again. But the thing is, my Intel® Chief River Chipset HM76 is not on the list of affected hardware(not ENTIRELY sure though). If anyone has any idea of what the problem to this might be, I'd be greatful. Edit: The hdd works perfectly fine even for large amounts of data if plugged in the usb 2.0 port!

  Read the article

• MS Excel 2010 - Using DSN + 32 bit drivers

  - by Kristiaan

  I need some advice as im running into a problem and so far i have been unable to find a solution. We have a set of reports developed in MS Excel that use DSN file to connect to data sources to retrieve data, these work fine on 32 / 64bit systems, however we are moving to a terminal server environment using windows 2008 R2 64Bit. The reports fail to run using the DSN's within this environment if we only have the 32bit drivers installed and configured in the ODBC settings, the minute we install the 64Bit drivers the software works. Is there a way / Method of getting Excel or the DSN file to NOT use the 64Bit driver, but force it to use the 32bit driver. ANSWERED - But due to low user score i cannot "answer" my own question... Sadly there is no way to-do what i want to-do, without a lot of very nasty and not 100% perfect reg hacks. If you need to access 32bit ODBC data sources the application in question has to be 32Bit. here is a link to just one forum post i found relating to this type of problem, it appears the only way i would be able to accomplish this is to remove the 64bit version of office and install the 32bit version instead of it. http://social.msdn.microsoft.com/Forums/en-US/accessdev/thread/5108f337-f06a-4518-afe3-d3c1abd040ef/

  Read the article

• Have it fixed or buy a new one?

  - by Workshop Alex

  My dual-monitor system has just become a single-monitor system again when the older monitor decided it would be nice to just turn to black. It's a Samsung LCD monitor and is over three years old. Not sure if the warranty is still valid but I just wonder what option would me more efficient: 1) Have the monitor fixed for a small amount. 2) Buy a new monitor for a slightly bigger amount. When monitors were still expensive, I wouldn't doubt about this and would just have my monitor repaired. But prices are so low nowadays, (and repairs are expensive) that I wonder if it's worth the trouble... Of course, I'm in no hurry since I still have another monitor. It's just that I liked the dual-monitor setup. Solved! Just ordered a new monitor. A Samsumg Syncmaster T260HD 25,5". Much more than it would cost me if I just had my old one repaired but I noticed that this one has a build-in TV tuner, plus speakers. It's way more expensive than a repair, but it's worth the additional value it provides.

  Read the article

• Centos iptables configuration for Wordpress and Gmail smtp

  - by Fabrizio

  Let me start off by saying that I'm a Centos newby, so all info, links and suggestions are very welcome! I recently set up a hosted server with Centos 6 and configured it as a webserver. The websites running on it are nothing special, just some low traffic projects. I tried to configure the server as default as possible, but I like it to be secure as well (no ftp, custom ssh port). Getting my Wordpress to run as desired, I'm running into some connection problems. 2 things are not working: installing plugins and updates through ssh2 (failed to connect to localhost:sshportnumber) sending emails from my site using the Gmail smtp (Failed to connect to server: Permission denied (13)) I have the feeling that these are both related to the iptables configuration, because I've tried everything else (I think). I tried opening up the firewall to accept traffic for ports 465 (gmail smtp) and ssh port (lets say this port is 8000), but both the issues remain. Ssh connections from the terminal are working fine though. After each change I tried implementing I restarted the iptables service. This is my iptables configuration (using vim): # Generated by iptables-save v1.4.7 on Sun Jun 1 13:20:20 2014 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 465 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited -A OUTPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A OUTPUT -o lo -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 465 -j ACCEPT COMMIT # Completed on Sun Jun 1 13:20:20 2014 Are there any (obvious) issues with my iptables setup considering the above mentioned issues? Saying that the firewall is doing exactly nothing in this state is also an answer... And again, if you have any other suggestions for me to increase security (considering the basic things I do with this box), I would love hear it, also the obvious ones! Thanks!

  Read the article

• Windows Action Center notification icon says Backup in Progress when no backup is occurring

  - by allquixotic

  How can I get Windows Action Center's little flag in the notification area to stop saying "Backup In Progress" on Windows 8? It's driving me nuts. I disabled the Windows Backup service completely and turned off File Recovery. Nothing that I can tell is using any disk I/O whatsoever, by examining Task Manager's resource monitor. It's just a visual cue that seems totally wrong considering my disk is only using about 50 KB/s of sporadic writes for superfetch etc. This wouldn't be a problem for me, since I rely on the knowledge that the Backup service is disabled and there's no disk activity, but I am trying to support a more traditional user who relies on visual cues from the operating system and trusts them over low-level observations like "...but the Windows Backup service is disabled!" Therefore this user still thinks that the backup is going on, even after the service is disabled. Technically, I think this is a bug in Windows 8. It really should not be displaying "Backup in Progress" if ... you know ... a backup, is not, in progress. Which it isn't. Is there a workaround?

  Read the article

• How do you notice that the batteries of you wireless mouse are dying out?

  - by hkBattousai

  I have a Logitech M705 wireless mouse. I'm first time using a wireless mouse, so I don't have much experience with the hardware features and behavior. It is rated that it runs for 3 years with the same batteries. I think this "3 year" rating is calculated for a very low usage and activity; like 2 hours a day. I'm using it for about 12 hours a day, so I expect it to run out of batteries in a much shorter time in my case. I have been using it for about half a year. Recently (for the last two weeks), it started to make some peculiar behavior when clicking and drafging objects. - When I click something, it sometimes double click it. - When I drag something from one place to another (or selecting some text), it sometimes drops the object in the halfway (when selecting text, the text which had selected up to that time becomes unselected and it starts to select the rest of the text from that moment), but it goes on being in the "left-button-pressed" state. It is like, the pressed button switches to "unpressed" state for a moment, then returns back to the "pressed" state. When one of these faults occur, it occurs several times sequentially. There is no problem in pointer movement, scrolling or right-clicking. Since the batteries last for a very long time for this device, I don't expect it to stop working in an instance. I expect it to give these kind of syndromes of a time period. My question is; Is this how batteries run out for a wireless mouse? Or, is this another kind of hardware/software problem?

  Read the article

• My Computer hangs for a few minutes just after startup, and then is fine.

  - by EvilChookie

  So I just built myself a reasonably beefy computer, and I installed Windows 7 on it. However, I start the machine up each morning and within a few minutes, the computer will semi hang. That is the mouse is responsive, and most of the time I can open task manager, or a new tab in Chrome. Occasionally windows will be labelled as 'Not responding'. Then, the machine will get over it's problem, and will be nice and quick until I turn it off. Here's my specs: CPU: AMD Phenom-II X4 955 Black (Quad Core, 3.2ghz) RAM: 4GB of DDR3 1300 MOBO: ASUS M4A785T-M (Latest BIOS) HARD DRIVES: 2x1TB Western Digital Caviar Blacks in RAID-0. OS: Windows 7 Ultimate x64. GPU: ASUS GT240 1GB. I believe this issue relates to the RAID array, as I didn't have the lockup problem before I created the array. I purchased a second drive and reformatted after creating a RAID array, since the single drive was a little on the pokey side (compared to the rest of the computer). What I have tried: Updated Raid Drivers Malware checks Windows Updates Unecessary Services CPU and Disk activity appears to be low (via Resource Monitor) No strange errors in the error log. Any thoughts?

  Read the article

• Setting up MySQL Linux slave with a Windows master

  - by philwilks

  I'm running a MySQL 5.0 database server on Windows Server 2008. The total size of the database is about 1Gb. I make daily backups, but I'd like to step up to having a slave server for extra protection. My thinking was that I wouldn't need the expense of a Windows machine to do this, and a Linux "cloud server" from RackSpace would do the job well for quite a low cost. However I have little experience with Linux, so I have a few questions... Does this sound like a good idea? Is there anything wrong with linking Windows and Linux MySQL servers? Does Linux have the equivalent of Remote Desktop Connection? If so can I use this from a Windows machine? Would a particular Linux distro be well suited to this task? RackSpace offer ArchLinux, CentOS, Debian, Fedora and Ubuntu. My immediate thinking is to go with Ubuntu as I've heard it's more friendly for people coming from a Windows background. Any comments you have would be very appreciated! Phil

  Read the article

• Why do hosts prefer Linux to Windows Server?

  - by iconiK

  So far I see a HUGE majority of hosts provide only Linux shared hosting, providing Windows only to VPS (or even to only dedicated servers). Why is it so? While Windows is a lot more expensive than Linux (though it depends on a lot of factors, not just initial and support license cost), it also provides ASP.NET, IIS and of course, Microsoft SQL Server. I know in the past it might have been because of cPanel being Linux only but now they have a Windows version. But still, why is Linux predominantly used on shared hosting? PHP works on both systems. IIS can be (and probably is) faster. MySQL runs on both systems as well. cPanel has a Windows version. Python, Perl, Ruby, all run on Windows as well. You even have MS SQL Server Express, which I find more superior than MySQL in both speed and features. Access is there for low usage requirements, as is SQLite (which is so great for quick small stuff). And with PowerShell you have a good alternative to the Unix shell. EDIT: I am looking for common reasons, I realize each hosting company (and/or it's clients) may have different needs. This becomes very important when you get to VPS or Cloud which give you a full operating system to use.

  Read the article

• Weird PCI bug: lots of missed packets, or data comes in "bursts"

  - by Thomas O

  I have an ABIT KN9 motherboard. It has one PCI-e x16 slot, three PCI-e x4 slots and two legacy PCI. My problem is with the legacy PCI (which I shall just call "PCI".) I currently have an Nvidia GeForce 8600 GT (a low end card) installed in the x16 slot and a TV card in PCI #1; the x4 slots are unused, as is PCI #2. I plan to upgrade the graphics card soon, the current card was spare. I sometimes install a USB expander in PCI #2 but it causes a lot of problems - see below. The problem is under Linux (Ubuntu 10.10, Linux 2.6.35-22-generic), but probably under all operating systems (I have not yet been able to test Windows, but I suspect it will do the same as the problems occur on the BIOS/POST side too, e.g. when using a USB keyboard on the expander the keyboard will not work at all) PCI has an enourmous delay, and packets arrive in large chunks. For example, when using the USB expander, my USB mouse lags and jumps in large steps every second or so, while using the motherboard USB does not present this problem. My TV card will only do one or two frames per second, and the program (xawtv) usually times out and crashes. In dmesg, I'm getting messages like: bttv0: timeout: drop=74, irq=154/100476, risc=31f6256c, bits: VSYNC HSYNC OFLOW RISCI for my TV card, and similar timeout issues for my USB expander with a mouse. I received the motherboard, processor and RAM second hand and have only just got around to building it, so I don't know if this problem has always existed, or if it's a result of my set up. If anyone has any hints or solutions it would be appreciated - this is kind of a show-stopper for me.

  Read the article

• nginx: dump HTTP requests for debugging

  - by Alexander Gladysh

  Ubuntu 10.04.2 nginx 0.7.65 I see some weird HTTP requests coming to my nginx server. To better understand what is going on, I want to dump whole HTTP request data for such queries. (I.e. dump all request headers and body somewhere I can read them.) Can I do this with nginx? Alternatively, is there some HTTP server that allows me to do this out of the box, to which I can proxy these requests by the means of nginx? Update: Note that this box has a bunch of normal traffic, and I would like to avoid capturing all of it on low level (say, with tcpdump) and filtering it out later. I think it would be much easier to filter good traffic first in a rewrite rule (fortunately I can write one quite easily in this case), and then deal with bogus traffic only. And I do not want to channel bogus traffic to another box just to be able to capture it there with tcpdump. Update 2: To give a bit more details, bogus request have parameter named (say) foo in their GET query (the value of the parameter can differ). Good requests are guaranteed not to have this parameter ever. If I can filter by this in tcpdump or ngrep somehow — no problem, I'll use these.

  Read the article

• How can I write directly to my Zune HD hard drive?

  - by iamgoat

  When syncing photos to the Zune HD it resizes them down to a much lower resolution which means I cannot load a high res picture on it (comic book) and zoom in to read it. This defeats the whole purpose of having a zoom feature. There is a registry hack you can make to get the Zune to display under My Computer. Then if you killed the zune process while it's syncing you'd be able to access it like a hard drive and copy files to it. It seems like the more recent firmware and/or Zune software version now prevents this. How can I treat it like an HDD and copy files to it? I simply want to take my original pictures folder and copy it over the low resolution versions the Zune software resized it to. An alternative option would be to remove the hard drive from it and see if I can connect it to a computer directly, but I just got this and don't want to disassemble it yet. Note to Microsoft: Why do you allow me to set the encoding quality of music, but not photos?

  Read the article

• Remote paging with Nagios when network is down and email won't work -- cellular modems and alternatives

  - by Quinten

  What is the best option for remote paging when network services are down? I'm looking for a solution that can let me know when network services are down during off-hours only, and especially when email/smtp services are out. Therefore, it needs to be redundant to our network and power supply. I'm imagining a cellular modem is one option. What's the price range for these? Is anybody using them and feel that they are worth the cost? I'm imagining that it's something we would end up sending an emergency page ~ 1x/month at most, so I'd like the pricing to reflect that--I don't mind a high per-page cost as long as it has a low recurring cost. Another option would be to expose at least one server to remote ping, and run a check script on a remote server. Are there paid options for this? Currently, we run Nagios on a Linux VM on a Windows 2008 Hyper-V host. It would be great if the solution would work in that environment, but I know it's tricky with external devices, and we could move Nagios to a standalone workstation if needed.

  Read the article

< Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >