Search Results

Search found 25894 results on 1036 pages for 'ask the readers'.

Page 151/1036 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• Wireless not working with a RTL8191SEvB

  - by Carlos Reis

  my wireless is not working in Ubuntu 11.10 and it worked fine in 11.04, i've done a fresh install and it detects the wireless but when i try to connect it keeps asking for the WPA key.Can anyone help me? I've tried to download the drivers from the realtek site but i get an error when i do "sudo make" i'm using a 64bit and i've tried the 32bit and nothing solves the problem. my wireless card: RTL8191SEvB

  Read the article

• Unable to get screen signal after purge FGLRX

  - by Boris

  I thought that my ATI driver was not running well so I wanted to re-instal it completely. I did: sudo apt-get remove --purge fglrx* sudo apt-get remove --purge xserver-xorg-video-ati xserver-xorg-video-radeon and after a boot I wanted to intal the ATI driver BUT at the boot no more signal to my screen. Since, every time I turn on my PC it gets to purple screen and then screen shuts down ! Note that: Even if the screen is off, PC seems to be running almost well: I m still able to use my network to access data shared with NFS. Using live USB I have no screen problem. I tried to plug my screen on an alternative output but it did not work. I tried CTRL+ALT+F1 while being on purple screen but it does not do anything, screen shut down anyway. I m going to try the SHIFT thing and learn from blackscreen wiki...

  Read the article

• Getting error-'General Error Mounting Filesystems' while installing ubuntu 12.04 alongside Windows 7 starter edition

  - by Yashendra Shukla

  I am trying to install Ubuntu 12.04 on my HP Mini 110 with 2 gb of ram and Windows 7 starter edition. However, when I try to boot from USB, the Ubuntu screen loads and then shows the message-'General Error Mounting Filesystem'. I have to press Ctrl+D to reboot, and the same process starts again until I remove my pen drive. I have tried making a Live USB from UNetBootin and the software Ubuntu suggests, downloaded from pendrivelinux.com. However, Ubuntu still won't load. I am new to the Ubuntu world and don't know what to do, please help.

  Read the article

• Streaming desktop with avconv - severe sound issues

  - by Tommy Brunn

  I'm trying to do some live streaming in Ubuntu 12.10, but I'm having some problems with audio. More specifically, the quality is complete garbage and it's at least 10 seconds out of sync with the video. I'm using an excellent guide found here to set up my loopback devices so that I can combine the desktop audio with the microphone input. It seems to work, as I'm able to stream both audio and video to Twitch.tv. But, as I said, the audio quality is terrible. The microphone audio is very, very low, but if I increase it, I get a horrible garbled sound that is absolutely unbearable. Nothing like that is present during VoIP calls or when recording sound alone with the sound recorder, so it's not an issue with the microphone itself. The entire audio stream is also delayed about 10-15 seconds compared to the video stream. I put together an imgur album of my settings. Here is some example output from when I'm streaming: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [x11grab @ 0x162fd80] device: :0.0+570,262 -> display: :0.0 x: 570 y: 262 width: 1280 height: 720 [x11grab @ 0x162fd80] shared memory extension found [x11grab @ 0x162fd80] Estimating duration from bitrate, this may be inaccurate Input #0, x11grab, from ':0.0+570,262': Duration: N/A, start: 1353181686.735113, bitrate: 884736 kb/s Stream #0.0: Video: rawvideo, bgra, 1280x720, 884736 kb/s, 30 tbr, 1000k tbn, 30 tbc [alsa @ 0x163fce0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x163fce0] Estimating duration from bitrate, this may be inaccurate Input #1, alsa, from 'pulse': Duration: N/A, start: 1353181686.773841, bitrate: N/A Stream #1.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s Incompatible pixel format 'bgra' for codec 'libx264', auto-selecting format 'yuv420p' [buffer @ 0x1641ec0] w:1280 h:720 pixfmt:bgra [scale @ 0x1642480] w:1280 h:720 fmt:bgra -> w:852 h:480 fmt:yuv420p flags:0x4 [libx264 @ 0x165ae80] VBV maxrate unspecified, assuming CBR [libx264 @ 0x165ae80] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 [libx264 @ 0x165ae80] profile Main, level 3.1 [libx264 @ 0x165ae80] 264 - core 123 r2189 35cf912 - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=2 deblock=1:0:0 analyse=0x1:0x111 me=hex subme=6 psy=1 psy_rd=1.00:0.00 mixed_ref=0 me_range=16 chroma_me=1 trellis=1 8x8dct=0 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=4 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=0 b_adapt=1 b_bias=0 direct=1 weightb=0 open_gop=1 weightp=1 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=30 rc=cbr mbtree=1 bitrate=712 ratetol=1.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 vbv_maxrate=712 vbv_bufsize=512 nal_hrd=none ip_ratio=1.25 aq=1:1.00 Output #0, flv, to 'rtmp://live.justin.tv/app/live_23011330_Pt1plSRM0z5WVNJ0QmCHvTPmpUnfC4': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: libx264, yuv420p, 852x480, q=-1--1, 712 kb/s, 1k tbn, 30 tbc Stream #0.1: Audio: libmp3lame, 44100 Hz, 2 channels, s16, 712 kb/s Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> libx264) Stream #1:0 -> #0:1 (pcm_s16le -> libmp3lame) Press ctrl-c to stop encoding frame= 17 fps= 0 q=0.0 size= 0kB time=10000000000.00 bitrate= 0.0kbitframe= 32 fps= 31 q=0.0 size= 0kB time=10000000000.00 bitrate= 0.0kbitframe= 40 fps= 23 q=29.0 size= 44kB time=0.03 bitrate=13786.2kbits/s dup=frame= 47 fps= 21 q=31.0 size= 93kB time=2.73 bitrate= 277.7kbits/s dup=0frame= 62 fps= 23 q=29.0 size= 160kB time=3.23 bitrate= 406.2kbits/s dup=0frame= 77 fps= 24 q=23.0 size= 209kB time=3.71 bitrate= 462.5kbits/s dup=0frame= 92 fps= 25 q=20.0 size= 267kB time=4.91 bitrate= 445.2kbits/s dup=0frame= 107 fps= 25 q=20.0 size= 318kB time=5.41 bitrate= 482.1kbits/s dup=0frame= 123 fps= 26 q=18.0 size= 368kB time=5.96 bitrate= 505.7kbits/s dup=0frame= 139 fps= 26 q=16.0 size= 419kB time=6.48 bitrate= 529.7kbits/s dup=0frame= 155 fps= 27 q=15.0 size= 473kB time=7.00 bitrate= 553.6kbits/s dup=0frame= 170 fps= 27 q=14.0 size= 525kB time=7.52 bitrate= 571.7kbits/s dup=0 frame= 180 fps= 25 q=-1.0 Lsize= 652kB time=7.97 bitrate= 670.0kbits/s dup=0 drop=32 //Here I stop the streaming video:531kB audio:112kB global headers:0kB muxing overhead 1.345945% [libx264 @ 0x165ae80] frame I:1 Avg QP:30.43 size: 39748 [libx264 @ 0x165ae80] frame P:45 Avg QP:11.37 size: 11110 [libx264 @ 0x165ae80] frame B:134 Avg QP:15.93 size: 27 [libx264 @ 0x165ae80] consecutive B-frames: 0.6% 0.0% 1.7% 97.8% [libx264 @ 0x165ae80] mb I I16..4: 7.3% 0.0% 92.7% [libx264 @ 0x165ae80] mb P I16..4: 0.1% 0.0% 0.1% P16..4: 49.1% 1.2% 2.1% 0.0% 0.0% skip:47.4% [libx264 @ 0x165ae80] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 0.1% 0.0% 0.0% direct: 0.0% skip:99.9% L0:42.5% L1:56.9% BI: 0.6% [libx264 @ 0x165ae80] coded y,uvDC,uvAC intra: 82.3% 87.4% 71.9% inter: 7.1% 8.4% 7.0% [libx264 @ 0x165ae80] i16 v,h,dc,p: 27% 29% 16% 28% [libx264 @ 0x165ae80] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 22% 21% 14% 8% 8% 8% 7% 5% 7% [libx264 @ 0x165ae80] i8c dc,h,v,p: 47% 22% 20% 11% [libx264 @ 0x165ae80] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0x165ae80] ref P L0: 96.4% 3.6% [libx264 @ 0x165ae80] kb/s:474.19 Received signal 2: terminating. Any ideas on how I can resolve this? The video delay is perfectly acceptable, so I wouldn't think that it's a network issue that's causing the delay in the audio. Any help would be appreciated.

  Read the article

• "ERROR:Could not find java.nio.file.Paths" when using Oracle JDK 1.7

  - by Ankit

  I want to try out some features rolled out in Oracle's new JDK 1.7. I followed the post:- Oracle JDK 1.7 but the post doesn't seem to help. I was trying to fetch out the structure for java.nio.file.Paths class file but got the following error:- buffer@ankit:~$ javap java.nio.file.Paths ERROR:Could not find java.nio.file.Paths However i can easily get the information about class structures till JAVA SE 1.6, here is an example:- buffer@ankit:~$ javap java.lang.Object Compiled from "Object.java" public class java.lang.Object{ public java.lang.Object(); public final native java.lang.Class getClass(); public native int hashCode(); public boolean equals(java.lang.Object); protected native java.lang.Object clone() throws java.lang.CloneNotSupportedException; public java.lang.String toString(); public final native void notify(); public final native void notifyAll(); public final native void wait(long) throws java.lang.InterruptedException; public final void wait(long, int) throws java.lang.InterruptedException; public final void wait() throws java.lang.InterruptedException; protected void finalize() throws java.lang.Throwable; static {}; } Running java -version gives the following result:- buffer@ankit:~$ java -version java version "1.7.0_09" Java(TM) SE Runtime Environment (build 1.7.0_09-b05) Java HotSpot(TM) 64-Bit Server VM (build 23.5-b02, mixed mode) SYSTEM INFORMATION buffer@ankit:~$ sudo update-alternatives --config java [sudo] password for buffer: There are 4 choices for the alternative java (providing /usr/bin/java). Selection Path Priority Status ------------------------------------------------------------ 0 /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/java 1061 auto mode 1 /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/java 1061 manual mode 2 /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/java 1051 manual mode 3 /usr/lib/jvm/jdk1.7.0_09/ 1 manual mode * 4 /usr/lib/jvm/jdk1.7.0_09/bin/java 1 manual mode buffer@ankit:~$ sudo update-alternatives --config javac There are 2 choices for the alternative javac (providing /usr/bin/javac). Selection Path Priority Status ------------------------------------------------------------ 0 /usr/lib/jvm/java-6-openjdk-amd64/bin/javac 1061 auto mode 1 /usr/lib/jvm/java-6-openjdk-amd64/bin/javac 1061 manual mode * 2 /usr/lib/jvm/jdk1.7.0_09/bin/javac 1 manual mode buffer@ankit:~$ sudo update-alternatives --config javaws There are 3 choices for the alternative javaws (providing /usr/bin/javaws). Selection Path Priority Status ------------------------------------------------------------ 0 /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/javaws 1061 auto mode 1 /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/javaws 1061 manual mode 2 /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/javaws 1060 manual mode * 3 /usr/lib/jvm/jdk1.7.0_09/bin/javaws 1 manual mode The directory structure of /usr/lib/jvm/ is as follows:- buffer@ankit:~$ ls -l /usr/lib/jvm/ total 24 lrwxrwxrwx 1 root root 24 Dec 2 2011 default-java -> java-1.6.0-openjdk-amd64 drwxr-xr-x 4 root root 4096 Nov 8 16:24 java-1.5.0-gcj-4.6 lrwxrwxrwx 1 root root 24 Dec 2 2011 java-1.6.0-openjdk -> java-1.6.0-openjdk-amd64 lrwxrwxrwx 1 root root 20 Oct 25 00:01 java-1.6.0-openjdk-amd64 -> java-6-openjdk-amd64 lrwxrwxrwx 1 root root 20 Oct 25 06:59 java-1.7.0-openjdk-amd64 -> java-7-openjdk-amd64 lrwxrwxrwx 1 root root 24 Dec 2 2011 java-6-openjdk -> java-1.6.0-openjdk-amd64 drwxr-xr-x 7 root root 4096 Nov 8 16:24 java-6-openjdk-amd64 drwxr-xr-x 3 root root 4096 Nov 8 16:24 java-6-openjdk-common drwxr-xr-x 5 root root 4096 Nov 8 05:48 java-7-openjdk-amd64 drwxr-xr-x 3 root root 4096 Nov 8 05:48 java-7-openjdk-common drwxr-xr-x 8 buffer buffer 4096 Sep 25 09:08 jdk1.7.0_09 Any help would be highly appreciated.

  Read the article

• How to mount a disk that supports Samba sharing (Using Disk Utility)

  - by Luis Alvarado - The Wolverine

  This might be a tricky question but here is the objective: Manage to mount a disk/partition automatically without (or at least trying to avoid): Editing any Samba configuration file Editing the fstab file and to make it a little bit harder, this needs to be done with the options for "Mount Options" in the Disk Utility: Note that if left as it is, every time a user mounts a partition/disk and then tries to share a folder in it, Windows users can see the share but can not access it, with a permission warning appearing. The point of all of this is to find the most user friendly (Oriented towards a GUI) way of enabling a partition to be mounted, accessed by the local user (Read, Write, Execute) and to also be able to, when needed, share a folder and have no problems reading/writing on it from another Ubuntu/Windows/Mac remote computer (Assuming both are in the same LAN network).

  Read the article

• Compile latest blender on ubuntu 12.0464bit?

  - by gabriel

  What i want is to compile latest blender from SVN. I am using this guide My issues are: How can i install it with the final .deb created file and how can i give this package to a ppa! So, when i execute sudo apt-get update; sudo apt-get install subversion build-essential gettext \ libxi-dev libsndfile1-dev \ libpng12-dev libfftw3-dev \ libopenexr-dev libopenjpeg-dev \ libopenal-dev libalut-dev libvorbis-dev \ libglu1-mesa-dev libsdl1.2-dev libfreetype6-dev \ libtiff4-dev libavdevice-dev \ libavformat-dev libavutil-dev libavcodec-dev libjack-dev \ libswscale-dev libx264-dev libmp3lame-dev python3.2-dev \ libspnav-dev it gives me this The following packages have unmet dependencies: libjack-dev : Depends: libjack0 (= 1:0.121.0+svn4538-3ubuntu1) but it is not going to be installed E: Unable to correct problems, you have held broken packages. I know that skype does not allow the installation of those libraries. Thanks

  Read the article

• How to report a crash bug with nothing on screen

  - by winniemiel05

  I would like to report an installation bug, but I can't launch ubuntu-bug : On my tablet (LDLC Janus, an Intel based tablet without OS installed by default), I have a problem when I install Ubuntu 11.04 or 11.10. Once the installation is finished, when I reboot, there is ABSOLUTELY nothing on screen, but Ubuntu boot correctly anyway : I choosed auto-login mode and I can hear the login sound. Even if I Ctrl+Alt+F1 or F2... there is nothing. But the livecd works fine (even touch screen even if without multi touch). I tried to install 10.10 it works, but as soon as I upgrade the same problem occure. i installed Fedora 15 and then Fedora 16 (because of other problems) and no problems with them. I would like to report this bug on launchpad but I don't know how to do to give devs logs files and other useful files which could help debug. Thanks a lot for your answer, I would really prefer using my tablet with Ubuntu (I miss U1, USC, Unity)

  Read the article

• Creating properly aligned partitions on a replacement disk

  - by Marius Gedminas

  I've a typical small office server with two hard disks configured for RAID-1 (mirroring). Each disk has several partitions: one for swap, the others paired in several /dev/mdX arrays. Every couple of years one of the disks dies and is replaced. The replacement typically goes something like this: # copy partition table from the remaining good disk to the empty replacement disk # (instead of /dev/good_disk and /dev/new_disk I use /dev/sda and /dev/sdb, as appropriate) sfdisk -d /dev/good_disk | sfdisk /dev/new_disk # install boot loader grub-install /dev/new_disk # create swap partition reusing the same UUID, so I don't need to edit /etc/fstab mkswap /dev/new_disk1 -U xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx # hot-add the new partitions to my RAID arrays mdadm /dev/md0 -a /dev/new_disk2 mdadm /dev/md1 -a /dev/new_disk5 mdadm /dev/md2 -a /dev/new_disk6 mdadm /dev/md3 -a /dev/new_disk7 mdadm /dev/md4 -a /dev/new_disk8 The disks were originally partitioned with cfdisk back in 2009, and so the partition table is aligned traditionally to cylinder boundaries (255 heads * 63 sectors). This is not the optimum configuration for new 4K-sector drives. My question is: how can I create a set of partitions for the new disk and ensure they're properly aligned, and have correct sizes for my RAID arrays (rounding up is acceptable, I suppose, but rounding down is definitely not)?

  Read the article

• Custom Xsession with Gnome visuals

  - by Siim K

  I'm trying to create a kiosk PC only for web browsing using this tutorial as a reference (only difference - I'm using Firefox instead of Chromium) It is working correctly in principle (only FF window opens when I log in using the Kiosk session) but it looks, well, super ugly. The scrollbar and right-click context menus look like from the 1990s - gray and boxy. How could I modify the session to get Gnome-like scrollbars/menus without the whole Gnome desktop (top/bottom panel etc)? My custom X session is currently set up like this: /usr/share/xsessions/kiosk.desktop: [Desktop Entry] Encoding=UTF-8 Name=Kiosk Mode Comment=Firefox Kiosk Mode Exec=/usr/share/xsessions/ffKiosk.sh Type=Application /usr/share/xsessions/ffKiosk.sh: #!/bin/bash while true; do firefox -height 768 -width 1024; sleep 1s; done

  Read the article

• What would cause the "gi" module to be missing from python?

  - by Catalin Dumitru

  After some not so clever editing of the default Python version in Ubuntu, from 2.7 to 3.2, I ended up breaking my entire system. After my computer imploded and everything stopped working, I tried to revert back my changes (by linking /usr/bin/python2.7 to /usr/bin/python and changing the default version in /usr/share/python/debian_defaults back to 2.7) but some things are still broken. For example when I type "import gi" in the python interpreter I get the fallowing message : >>> import gi Traceback (most recent call last): File "<stdin>", line 1, in <module> ImportError: No module named gi >>> error which appears with some programs too (eg: gnome tweak tool). I have tried re-installing python both from the software center and from sources, but the same error persists. Python -- version now returns : Python 2.7.2 and also some software packages which depend on python 2.7 are now working (for example the software center), but some things are still broken. Is there anything I can do to completely re-install python 2.7 as the default version?

  Read the article

• Help installing wine

  - by Carter

  The following packages have unmet dependencies: wine1.5 : Depends: wine1.5-i386 (= 1.5.16-0ubuntu1) but it is not installable Recommends: gnome-exe-thumbnailer but it is not going to be installed or kde-runtime but it is not going to be installed Recommends: ttf-droid Recommends: ttf-mscorefonts-installer but it is not going to be installed Recommends: ttf-umefont but it is not going to be installed Recommends: ttf-unfonts-core but it is not going to be installed Recommends: winbind but it is not going to be installed Recommends: winetricks but it is not going to be installed E: Unable to correct problems, you have held broken packages. I get this error when trying to install wine. Please help!

  Read the article

• How to setup IPSec with Amazon EC2

  - by bonzi

  How to setup an IPSec connection from my ubuntu laptop to Amazon EC2 instance? I tried setting it up using elastic IP and VPC with the following openswan configuration but it is not working. conn host-to-host left=%defaultroute leftsubnet=EC2PRIVATEIP/32 # Local netmask leftid=ELASTICIP leftrsasigkey= connaddrfamily=ipv4 right=1laptopip # Remote IP address rightid=laptopip rightrsasigkey= ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel

  Read the article

• How do I install sensors-applet?

  - by honestann

  I want to install sensors-applet onto my Ubuntu 12.04 computer. The instructions on this (and other) webpages says to enter this command in a command terminal: sudo apt-get install sensors-applet This is a gnome applet and gnome isn't exactly obscure. Why can sensors-applet package not be found? Before you say "no", note that I was able to execute "gnome-panel" to add a bar/panel along the bottom of my desktop, add 8 cpu-frequency applets to the bar (one per CPU core), and add gnome-panel to my startup applications. So I've already done the basics, and believe all I need now is to be able to download and install the sensors-applet to have that temperature applet available on the panel too. See here.

  Read the article

• Purple line on left side of screen when I use graphics card's hdmi port

  - by fab

  My graphics card is a nVidia GeForce GTX 660 2GB. When I plug HDMI into mobo it works fine. When I plug it into the graphics card (with 2nd monitor too) it shows a purple vertical line on the left side. It adds 2 pixels to the width and I can't adjust it with my monitor. It doesn't come up when I print screen. I tried changing the driver to the binary one (at the top) but that made it not show up at all. What do I do? Are some graphics cards just not compatible?

  Read the article

• Upgrading to Mono 2.8

  - by Oli

  Mono 2.8 was recently released boasting a couple of large performance improvements. It's far too late for it to make it into Maverick and I'm fairly inpatient. I don't use Mono for anything mission-critical (just playing music and sorting photos) and if it breaks everything related to Mono, I can probably either live with it or fix it. I'm aware of how much I stand to lose if I mess things up. So with that acknowledged, does anybody here know how to build Mono in a way where it could be dropped in to replace the current Mono (2.6.7)? By this I mean ideally mirroring the packages that Ubuntu uses so that if the worse does happen, I can just downgrade the packages. Or is there a PPA that does all this for me?

  Read the article

• Usb WiFi dongle pluggin in doesnt create wlan0 interface

  - by zuba

  I use D-Link DWA-110 WiFi usb dongle. It used to be working well, but after some config changes I broke something and now when I plug the dongle in I see it in lsusb output, but wlan0 isn't created and the led on the dongle doesn't light. What to check out? ~ > uname -a Linux Distress 3.2.0-56-generic #86-Ubuntu SMP Wed Oct 23 17:31:43 UTC 2013 i686 i686 i386 GNU/Linux dmesg shows [ 667.824095] usb 1-8: new high-speed USB device number 6 using ehci-pci [ 668.117996] usb 1-8: New USB device found, idVendor=07d1, idProduct=3c07 [ 668.118007] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 668.118015] usb 1-8: Product: 802.11 bg WLAN [ 668.118021] usb 1-8: Manufacturer: Ralink

  Read the article

• Installation failure

  - by Peter Kelson

  I have just downloaded Ubuntu and burned an installation DVD. I used it to install Ubuntu on a PC running Windows XP choosing the option to run Ubuntu alongside Windows. I chose to install the additional updates after initial installation. When I choose Ubuntu from the menu displayed on boot-up I get a purple and yellow screen which is completely blank except for the functioning mouse pointer. I would be grateful for suggestions on how to fix this.

  Read the article

• How do I play a Blu Ray disc?

  - by hugocreal

  Hello All, I want play a Blu Ray Video from my hard drive with Boxee, but it chokes all the time, i try play with others video players but is the same. I think that is a 10gb .mkv file with 10Gb. Stuttering video with VLC , mplayer, and the default video player on ubuntu... I read in many Forums just can´t put this to work. Any idea? thanks. Ubuntu 10.10, My PC specs: Single Core 2Ghz ATI HD 4350 (i have installed the drivers from "Hardware Drivers"), 2G Memory

  Read the article

• How can I restore a corrupted Shotwell db?

  - by Yann Dìnendal

  While I was importing photos from a SD card in Shotwell, my laptop has crashed (shutdown because of over-heating). Now, I can no longer launch Shotwell: $ shotwell ** ERROR:x86_64-linux-gnu/db/VersionTable.c:104:version_table_construct: assertion failed: (res == SQLITE_OK) If I move the .db file ~/.shotwell/data/photo.db elsewhere so it is no longer present (but backed-up), shotwell will launch, but will rebuild its library, which will be empty. I can re-import the folders shotwell creates, but I lose nearly all meta-data (most importantly the "folders", or events, and their main picture) Is there a way to repair/rebuild/restore photo.db? How can I see what's inside? how bad it's damaged? Or is there another way to get back my events and imports?

  Read the article

• No input method choice appear on iBus

  - by phanect

  I've installed iBus and ibus-mozc, and an input method engine of Japanese from the repository, and attempted to enable mozc from Preference > "Input Method" tab > "Select Input Method" combo box. However, there is no choice to select, so I couldn't enable mozc. I also tried ibus-anthy, another legacy Japanese input method, but the situation was the same and I couldn't use anthy. Same problem is also occuring in openSUSE 12.1, so I don't think this is distribution-specific problem. In addition, this trouble also happened when I installed ibus-pynin, so this is not Japanese-specific. Any idea to find the cause of this trouble?

  Read the article

• offline installation of video plugins

  - by israel

  Please help I installed Ubuntu11.10 32bit in an IBMTP41 notebook, that is NOT connected to the internet, tried running video files such as .mp4,.flv,.avi,.Xvid, in Movie Player but it asks for plugins, see the list below mp4: MPEG-4 AAC decoder; H.264 decoder flv: SorensonSpark Video decoder; MPEG-1 Layer3(MP3) decoder avi: MPEG-1 Layer3 (MP3) decoder; MPEG video decoder XviD: AC-3 (ATSC A/52) decoder; XviD MPEG-4 decoder how do i donwload (from another computer with internet) and install all these plugins and their dependencies. I also want to install the VLC Media player and its dependencies I assume this is related to the restricted codecs and I have tried donwnload/install them with no success. I'll appreciate all ur help

  Read the article

• Acer aspire 5735z wireless not working after upgrade to 11.10

  - by Jon

  I cant get my wifi card to work at all after upgrading to 11.10 Oneiric. I'm not sure where to start to fix this. Ive tried using the additional drivers tool but this shows that no additional drivers are needed. Before my upgrade I had a drivers working for the Rt2860 chipset. Any help on this would be much appreciated.... thanks Jon jon@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:72:ec:76:d5 inet addr:192.168.1.134 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:72ff:feec:76d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7846 errors:0 dropped:0 overruns:0 frame:0 TX packets:7213 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8046624 (8.0 MB) TX bytes:1329442 (1.3 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:91 errors:0 dropped:0 overruns:0 frame:0 TX packets:91 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34497 (34.4 KB) TX bytes:34497 (34.4 KB) Ive included by dmesg output below [ 0.428818] NET: Registered protocol family 2 [ 0.429003] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.430562] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.436614] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.437409] TCP: Hash tables configured (established 524288 bind 65536) [ 0.437412] TCP reno registered [ 0.437431] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437482] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437678] NET: Registered protocol family 1 [ 0.437705] pci 0000:00:02.0: Boot video device [ 0.437892] PCI: CLS 64 bytes, default 64 [ 0.437916] Simple Boot Flag at 0x57 set to 0x1 [ 0.438294] audit: initializing netlink socket (disabled) [ 0.438309] type=2000 audit(1319243447.432:1): initialized [ 0.440763] Freeing initrd memory: 13416k freed [ 0.468362] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.488192] VFS: Disk quotas dquot_6.5.2 [ 0.488254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.488888] fuse init (API version 7.16) [ 0.488985] msgmni has been set to 5890 [ 0.489381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.489413] io scheduler noop registered [ 0.489415] io scheduler deadline registered [ 0.489460] io scheduler cfq registered (default) [ 0.489583] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.489633] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 0.489699] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.489741] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 0.489800] pcieport 0000:00:1c.2: setting latency timer to 64 [ 0.489841] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X [ 0.489904] pcieport 0000:00:1c.3: setting latency timer to 64 [ 0.489944] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X [ 0.490006] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.490047] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X [ 0.490126] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.490149] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.490196] intel_idle: MWAIT substates: 0x1110 [ 0.490198] intel_idle: does not run on family 6 model 15 [ 0.491240] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.493473] ACPI: AC Adapter [ADP1] (on-line) [ 0.493590] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 0.496771] ACPI: Lid Switch [LID0] [ 0.496818] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 0.496823] ACPI: Sleep Button [SLPB] [ 0.496865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 0.496869] ACPI: Power Button [PWRF] [ 0.496900] ACPI: acpi_idle registered with cpuidle [ 0.498719] Monitor-Mwait will be used to enter C-1 state [ 0.498753] Monitor-Mwait will be used to enter C-2 state [ 0.498761] Marking TSC unstable due to TSC halts in idle [ 0.517627] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.517630] ACPI: Thermal Zone [TZS0] (67 C) [ 0.524796] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.524799] ACPI: Thermal Zone [TZS1] (67 C) [ 0.524823] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.524852] ERST: Table is not found! [ 0.524948] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.680991] ACPI: Battery Slot [BAT0] (battery present) [ 0.688567] Linux agpgart interface v0.103 [ 0.688672] agpgart-intel 0000:00:00.0: Intel GM45 Chipset [ 0.688865] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 0.689786] agpgart-intel 0000:00:00.0: detected 65536K stolen memory [ 0.689912] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.691006] brd: module loaded [ 0.691510] loop: module loaded [ 0.691967] Fixed MDIO Bus: probed [ 0.691990] PPP generic driver version 2.4.2 [ 0.692065] tun: Universal TUN/TAP device driver, 1.6 [ 0.692067] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.692146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.692181] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.692206] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.692210] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.692255] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.692289] ehci_hcd 0000:00:1a.7: debug port 1 [ 0.696181] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 0.696202] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf8904800 [ 0.712014] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.712131] hub 1-0:1.0: USB hub found [ 0.712136] hub 1-0:1.0: 6 ports detected [ 0.712230] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.712243] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.712247] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.712287] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.712315] ehci_hcd 0000:00:1d.7: debug port 1 [ 0.716201] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 0.716216] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8904c00 [ 0.732014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.732130] hub 2-0:1.0: USB hub found [ 0.732135] hub 2-0:1.0: 6 ports detected [ 0.732209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.732223] uhci_hcd: USB Universal Host Controller Interface driver [ 0.732254] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.732262] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.732265] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.732298] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.732325] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820 [ 0.732441] hub 3-0:1.0: USB hub found [ 0.732445] hub 3-0:1.0: 2 ports detected [ 0.732508] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 0.732514] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.732518] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.732553] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.732577] uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001840 [ 0.732696] hub 4-0:1.0: USB hub found [ 0.732700] hub 4-0:1.0: 2 ports detected [ 0.732762] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.732768] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.732772] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.732805] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.732829] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001860 [ 0.732942] hub 5-0:1.0: USB hub found [ 0.732946] hub 5-0:1.0: 2 ports detected [ 0.733007] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.733014] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.733017] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.733057] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.733082] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880 [ 0.733202] hub 6-0:1.0: USB hub found [ 0.733206] hub 6-0:1.0: 2 ports detected [ 0.733265] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.733273] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.733276] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.733313] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.733351] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018a0 [ 0.733466] hub 7-0:1.0: USB hub found [ 0.733470] hub 7-0:1.0: 2 ports detected [ 0.733532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.733539] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.733542] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.733578] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.733610] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0 [ 0.733730] hub 8-0:1.0: USB hub found [ 0.733736] hub 8-0:1.0: 2 ports detected [ 0.733843] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.751594] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.751605] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.751732] mousedev: PS/2 mouse device common for all mice [ 0.752670] rtc_cmos 00:08: RTC can wake from S4 [ 0.752770] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 0.752796] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 0.752907] device-mapper: uevent: version 1.0.3 [ 0.752976] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected] [ 0.753028] cpuidle: using governor ladder [ 0.753093] cpuidle: using governor menu [ 0.753096] EFI Variables Facility v0.08 2004-May-17 [ 0.753361] TCP cubic registered [ 0.753482] NET: Registered protocol family 10 [ 0.753966] NET: Registered protocol family 17 [ 0.753992] Registering the dns_resolver key type [ 0.754113] PM: Hibernation image not present or could not be loaded. [ 0.754131] registered taskstats version 1 [ 0.771553] Magic number: 15:152:507 [ 0.771667] rtc_cmos 00:08: setting system clock to 2011-10-22 00:30:48 UTC (1319243448) [ 0.772238] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.772240] EDD information not available. [ 0.774165] Freeing unused kernel memory: 984k freed [ 0.774504] Write protecting the kernel read-only data: 10240k [ 0.774755] Freeing unused kernel memory: 20k freed [ 0.775093] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 0.779727] Freeing unused kernel memory: 1400k freed [ 0.801946] udevd[84]: starting version 173 [ 0.880950] sky2: driver version 1.28 [ 0.881046] sky2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.881096] sky2 0000:02:00.0: setting latency timer to 64 [ 0.881197] sky2 0000:02:00.0: Yukon-2 Extreme chip revision 2 [ 0.881871] sky2 0000:02:00.0: irq 45 for MSI/MSI-X [ 0.896273] sky2 0000:02:00.0: eth0: addr 00:1d:72:ec:76:d5 [ 0.910630] ahci 0000:00:1f.2: version 3.0 [ 0.910647] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.910710] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X [ 0.910775] ahci: SSS flag set, parallel bus scan disabled [ 0.910812] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 0.910816] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs [ 0.910821] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.941773] scsi0 : ahci [ 0.941954] scsi1 : ahci [ 0.942038] scsi2 : ahci [ 0.942118] scsi3 : ahci [ 0.942196] scsi4 : ahci [ 0.942268] scsi5 : ahci [ 0.942332] ata1: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904100 irq 46 [ 0.942336] ata2: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904180 irq 46 [ 0.942339] ata3: DUMMY [ 0.942340] ata4: DUMMY [ 0.942344] ata5: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904300 irq 46 [ 0.942347] ata6: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904380 irq 46 [ 1.028061] usb 1-5: new high speed USB device number 2 using ehci_hcd [ 1.181775] usbcore: registered new interface driver uas [ 1.260062] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.261126] ata1.00: ATA-8: Hitachi HTS543225L9A300, FBEOC40C, max UDMA/133 [ 1.261129] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.262360] ata1.00: configured for UDMA/133 [ 1.262518] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54322 FBEO PQ: 0 ANSI: 5 [ 1.262716] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.262762] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 1.262824] sd 0:0:0:0: [sda] Write Protect is off [ 1.262827] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.262851] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.287277] sda: sda1 sda2 sda3 [ 1.287693] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.580059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.581188] ata2.00: ATAPI: HL-DT-STDVDRAM GT10N, 1.00, max UDMA/100 [ 1.582663] ata2.00: configured for UDMA/100 [ 1.584162] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT10N 1.00 PQ: 0 ANSI: 5 [ 1.585821] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.585824] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.585953] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.586038] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.632061] usb 6-1: new low speed USB device number 2 using uhci_hcd [ 1.908056] ata5: SATA link down (SStatus 0 SControl 300) [ 2.228065] ata6: SATA link down (SStatus 0 SControl 300) [ 2.228955] Initializing USB Mass Storage driver... [ 2.229052] usbcore: registered new interface driver usb-storage [ 2.229054] USB Mass Storage support registered. [ 2.235827] scsi6 : usb-storage 1-5:1.0 [ 2.235987] usbcore: registered new interface driver ums-realtek [ 2.244451] input: B16_b_02 USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input4 [ 2.244598] generic-usb 0003:046D:C025.0001: input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1/input0 [ 2.244620] usbcore: registered new interface driver usbhid [ 2.244622] usbhid: USB HID core driver [ 3.091083] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 3.238275] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS [ 3.348261] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.351897] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 47.138012] udevd[334]: starting version 173 [ 47.177678] lp: driver loaded but no devices found [ 47.197084] wmi: Mapper loaded [ 47.197526] acer_wmi: Acer Laptop ACPI-WMI Extras [ 47.210227] acer_wmi: Brightness must be controlled by generic video driver [ 47.566578] Disabling lock debugging due to kernel taint [ 47.584050] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 47.620666] type=1400 audit(1319239895.347:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=624 comm="apparmor_parser" [ 47.620934] type=1400 audit(1319239895.347:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=624 comm="apparmor_parser" [ 47.621108] type=1400 audit(1319239895.347:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=624 comm="apparmor_parser" [ 47.633056] [drm] Initialized drm 1.1.0 20060810 [ 47.722594] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 47.722602] i915 0000:00:02.0: setting latency timer to 64 [ 47.807152] ndiswrapper (check_nt_hdr:141): kernel is 64-bit, but Windows driver is not 64-bit;bad magic: 010B [ 47.807159] ndiswrapper (load_sys_files:206): couldn't prepare driver 'rt2860' [ 47.807930] ndiswrapper (load_wrap_driver:108): couldn't load driver rt2860; check system log for messages from 'loadndisdriver' [ 47.856250] usbcore: registered new interface driver ndiswrapper [ 47.861772] i915 0000:00:02.0: irq 47 for MSI/MSI-X [ 47.861781] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 47.861783] [drm] Driver supports precise vblank timestamp query. [ 47.861842] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 47.980620] fixme: max PWM is zero. [ 48.286153] fbcon: inteldrmfb (fb0) is primary device [ 48.287033] Console: switching to colour frame buffer device 170x48 [ 48.287062] fb0: inteldrmfb frame buffer device [ 48.287064] drm: registered panic notifier [ 48.333883] acpi device:02: registered as cooling_device2 [ 48.334053] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 48.334128] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 48.334203] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 48.334644] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334652] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334673] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 48.334737] HDA Intel 0000:00:1b.0: irq 48 for MSI/MSI-X [ 48.334772] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 48.356107] Adding 261116k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:261116k [ 48.380946] hda_codec: ALC268: BIOS auto-probing. [ 48.390242] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 48.390365] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 48.490870] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr [ 48.917990] ppdev: user-space parallel port driver [ 48.950729] type=1400 audit(1319239896.675:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=941 comm="apparmor_parser" [ 48.951114] type=1400 audit(1319239896.675:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=941 comm="apparmor_parser" [ 48.977706] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000 [ 49.048871] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 [ 49.078713] sky2 0000:02:00.0: eth0: enabling interface [ 49.079462] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 50.762266] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 50.762702] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.751478] type=1400 audit(1319239902.475:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=1039 comm="apparmor_parser" [ 54.755907] type=1400 audit(1319239902.479:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1040 comm="apparmor_parser" [ 54.756237] type=1400 audit(1319239902.483:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1040 comm="apparmor_parser" [ 54.756417] type=1400 audit(1319239902.483:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1040 comm="apparmor_parser" [ 54.764825] type=1400 audit(1319239902.491:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1041 comm="apparmor_parser" [ 54.768365] type=1400 audit(1319239902.495:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=1041 comm="apparmor_parser" [ 54.770601] type=1400 audit(1319239902.495:13): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=1041 comm="apparmor_parser" [ 54.770729] type=1400 audit(1319239902.495:14): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=1038 comm="apparmor_parser" [ 54.775181] type=1400 audit(1319239902.499:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1043 comm="apparmor_parser" [ 54.775533] type=1400 audit(1319239902.499:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1043 comm="apparmor_parser" [ 54.936691] init: failsafe main process (891) killed by TERM signal [ 54.944583] init: apport pre-start process (1096) terminated with status 1 [ 55.000373] init: apport post-stop process (1160) terminated with status 1 [ 55.005291] init: gdm main process (1159) killed by TERM signal [ 59.782579] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [ 60.992021] eth0: no IPv6 routers present [ 61.936072] device eth0 entered promiscuous mode [ 62.053949] Bluetooth: Core ver 2.16 [ 62.054005] NET: Registered protocol family 31 [ 62.054007] Bluetooth: HCI device and connection manager initialized [ 62.054010] Bluetooth: HCI socket layer initialized [ 62.054012] Bluetooth: L2CAP socket layer initialized [ 62.054993] Bluetooth: SCO socket layer initialized [ 62.058750] Bluetooth: RFCOMM TTY layer initialized [ 62.058758] Bluetooth: RFCOMM socket layer initialized [ 62.058760] Bluetooth: RFCOMM ver 1.11 [ 62.059428] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 62.059432] Bluetooth: BNEP filters: protocol multicast [ 62.460389] init: plymouth-stop pre-start process (1662) terminated with status 1 '

  Read the article

• Tomboy error while tring to sync with Ubuntu one; Can anyone help?

  - by Michael Chapman

  So I'm sure you've heard the song before, but after trying to sync my notes with Ubuntu One(on 10.10 AMD64) I get "Could not synchronize notes. Check the details below and try again." Of course the problem is that there are no details and trying again doesn't help. So I ran tomboy -debug and compared my error to any thing I could find about similar problems (such as the post here) but found nothing useful. Any way here's my first error, I got this using preferencessynchronizationUbuntu_one [ERROR 21:08:42.271] Synchronization failed with the following exception: String was not recognized as a valid DateTime. at System.DateTime.Parse (System.String s, IFormatProvider provider, DateTimeStyles styles) [0x00000] in <filename unknown>:0 at System.DateTime.Parse (System.String s, IFormatProvider provider) [0x00000] in <filename unknown>:0 at System.DateTime.Parse (System.String s) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.NoteInfo.ParseJson (Hyena.Json.JsonObject jsonObj) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.UserInfo.ParseJsonNoteArray (Hyena.Json.JsonArray jsonArray) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.UserInfo.ParseJsonNotes (System.String jsonString, System.Nullable`1& latestSyncRevision) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.UserInfo.GetNotes (Boolean includeContent, Int32 sinceRevision, System.Nullable`1& latestSyncRevision) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.WebSyncServer.GetNoteUpdatesSince (Int32 revision) [0x00000] in <filename unknown>:0 at Tomboy.Sync.SyncManager.SynchronizationThread () [0x00000] in <filename unknown>:0 The next thing I tried was using preferencessynchronizationtomboy_web with the default 'http://one.ubuntu.com/notes/' and got the same error plus one more. [ERROR 21:12:31.949] System.ObjectDisposedException: The object was used after being disposed. at System.Net.HttpListener.CheckDisposed () [0x00000] in <filename unknown>:0 at System.Net.HttpListener.EndGetContext (IAsyncResult asyncResult) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.WebSyncPreferencesWidget.<OnAuthButtonClicked>m__1 (IAsyncResult localResult) [0x00000] in <filename unknown>:0 [ERROR 21:13:19.245] Synchronization failed with the following exception: String was not recognized as a valid DateTime. at System.DateTime.Parse (System.String s, IFormatProvider provider, DateTimeStyles styles) [0x00000] in <filename unknown>:0 at System.DateTime.Parse (System.String s, IFormatProvider provider) [0x00000] in <filename unknown>:0 at System.DateTime.Parse (System.String s) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.NoteInfo.ParseJson (Hyena.Json.JsonObject jsonObj) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.UserInfo.ParseJsonNoteArray (Hyena.Json.JsonArray jsonArray) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.UserInfo.ParseJsonNotes (System.String jsonString, System.Nullable`1& latestSyncRevision) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.Api.UserInfo.GetNotes (Boolean includeContent, Int32 sinceRevision, System.Nullable`1& latestSyncRevision) [0x00000] in <filename unknown>:0 at Tomboy.WebSync.WebSyncServer.GetNoteUpdatesSince (Int32 revision) [0x00000] in <filename unknown>:0 at Tomboy.Sync.SyncManager.SynchronizationThread () [0x00000] in <filename unknown>:0 I Have also tried removing then re-adding My computer from my Ubuntu One account, but that did not help either. The only other Thing I have noticed is that under systempreferencesubuntu one services, "Notes" is not listed as a service. I don't know if this is normal or not. Thanks for any help and please let me know if anything is confusing.

  Read the article

• Where did PlayOnLinux install Microsoft office 2007 to?

  - by iDarine

  After I installed playonlinux, I immediately installed the microsoft office 2007. I pasted an .iso image on my desktop and extracted it on a folder, and after that I installed it using the playonlinux. After several loadings the playonlinux prompted installing Internet Explorer 6 and after that, it said that office 2007 was succesfully installed, and I cant find where is office 2007 installed. Can you help me?

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >