Search Results

Search found 5595 results on 224 pages for '302 permanent redirect'.

Page 152/224 | < Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >

  • nginx subdomains improperly act like wildcard?

    - by binjured
    I have an odd problem with nginx subdomains. First, my configuration: server { listen 443 ssl; server_name secure.example.com; ssl_certificate example.crt; ssl_certificate_key example.key; keepalive_timeout 70; location / { fastcgi_pass 127.0.0.1:8000; ... } } server { listen 80; server_name example.com www.example.com; location / { fastcgi_pass 127.0.0.1:8000; ... } } The idea being that I have a secure domain, secure.example.com and a normal domain, example.com. In practice, I can go to https://example.com and http://secure.example.com. I worked around the second issue with an intermediary server: server { listen 80; server_name secure.example.com; rewrite ^(.*) https://secure.example.com$1 permanent; } But this is not an optimal solution and I'd have to create another one to redirect https on the tld to the subdomain. I feel like I must be doing something wrong if I need multiple servers like that. Why does https://example.com work when there is no server listening on 443 there? Shouldn't it just fail to connect? I'm rather confused.

    Read the article

  • Same domain only : smtp; 5.1.0 - Unknown address error 530-'SMTP authentication is required

    - by user124672
    I have a very strange problem after moving my netwave.be domain from WebHost4Life to Arvixe. I configured several email adresses, like [email protected] and [email protected]. For POP3 I can use mail.netwave.be, a mailserver hosted by Arvixe. However, for SMTP I have to use relay.skynet.be. Skynet (Belgacom) is one of the biggest internet providers in Belgium and blocks smtp requests to external mailservers. So for years I've been using relay.skynet.be to send my messages using [email protected] as the sender. The worked perfectly. After moving my domain to Arvixe, this is no longer the case. I can send emails to people, no problem. I have received emails too, so I suspect that's ok too. But I can't send emails from one user of my domain to another user. For example, if I send a mail from [email protected] to [email protected], relay.skynet.be picks up the mail just fine. A few seconds later, I get a 'Delivery Status Notification (Failure)' mail that contains: Reporting-MTA: dns; mailrelay012.isp.belgacom.be Final-Recipient: rfc822;[email protected] Action: failed Status: 5.0.0 (permanent failure) Remote-MTA: dns; [69.72.141.4] Diagnostic-Code: smtp; 5.1.0 - Unknown address error 530-'SMTP authentication is required.' (delivery attempts: 0) Like I said, this only seems to be the case when both the sender and recipient are adresses of a domain hosted by Arvixe. I have serveral accounts not related to Arvixe at all. I can use relay.skynet.be to send mail to [email protected] using these accounts. Likewise, I can use relay.skynet.be to send mail from [email protected] to these accounts. but not from one Arvixe account to another. I hope I have clearly outlined the problem and someone will be able to help me.

    Read the article

  • TeamCity EC2 Integration via ISA Server

    - by Tim Long
    I have a TeamCity server which is actually installed on SBS 2003 Premium with ISA Server (firewall/proxy) installed. My ADSL connection has multiple IP addresses, which all resolve directly to my SBS external NIC. The NIC is therefore multi-homed and I have allocated one of the IP addresses specifically to TeamCity. In ISA, I've created an access rule to allow the traffic in. I can access my TeamCity server externally and view the web interface, that all works fine. I want to use the Amazon EC2 integration in TeamCity to launch build agents 'in the cloud'. The problem I am having is that when the agent starts, it sees the server and registers, then just sits there waiting. On the server side, the agent appears as 'disconnected'. Examining the settings, the agent's IP address appears to be that of the external NIC. What I think might be happening is that the traffic is undergoing Network Address Translation (NAT) so that TeamCity always thinks the agent is locally installed and therefore can't communicate with the actual remote agent. This seems to happen even though I have a permanent static IP address dedicated to TeamCity. So, the question is this. How can I make traffic to a specific IP address pass through the ISA server un-NATted?

    Read the article

  • How to permanently "renice" a process on Mac OS X (or iOS, etc)?

    - by mralexgray
    I use a nice (free) process manager called ATMonitor for Mac OS X that has a lot of cool hidden features... one of which is being able to click on a running process.. and set the "renice" from +20 (less priority) to -20 (highest priority). The best part.... it sticks between restarts... SO you want XYZ to get full attention all the time.. you set it once and it's done... I want to do the same thing (renice a process) on an iPad running a particular daemon.. and I don't know how to set a renice permanently. I can do it once, and it works fine... But the setting is lost on a reboot. I read somewhere.. Now, as for permanently resetting the priority of a process, this can't be done directly. You can fake it, however, with a shell script that starts the app and then immediately renice's it. Give that script a ".command" extension and it will be double-clickable in the GUI. Not very elegant, but it gets the job done. But as it says.. not very elegant, and I dont think this is how ATMonitor does it.... I found this thread.... http://superuser.com and they gave a way to do it as a launch argument, but no apparent way to save it as a persistent value... for instance - if the program wasn't going to be started by launchd... How do I set a permanent renice level, per executable binary, independent of it's PID, when, how or why it was launched?

    Read the article

  • 502 Bad Gateway - nginx

    - by ADH2
    I am randomly receiving 502 Bad Gateway error pages - I can reproduce this issue by modifying hosting plans in plesk 11 and in the same time refreshing a page for a minute or two. When I get the 502 error page all I have to do is refresh the browser and the page refreshes properly. i am using centos 6 this it from todays log (/var/log/nginx/error.log): 2012/12/04 10:52:07 [error] 21272#0: *545 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: 82.77.68.111, server: likeit-craiova.ro, request: "GET / HTTP/1.1", upstream: "http://195.254.135.113:7080/", host: "likeit-craiova.ro" this is the nginx config (/etc/nginx/nginx.conf) #user nginx; worker_processes 1; #error_log /var/log/nginx/error.log; #error_log /var/log/nginx/error.log notice; #error_log /var/log/nginx/error.log info; #pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; proxy_buffer_size 128k; proxy_buffers 4 256k; proxy_busy_buffers_size 256k; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; #tcp_nodelay on; #gzip on; #gzip_disable "MSIE [1-6]\.(?!.*SV1)"; server_tokens off; include /etc/nginx/conf.d/*.conf; } fastcgi config file (/etc/nginx/fastcgi.conf): fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; fastcgi parameters config (/etc/nginx/fastcgi_params): fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; alsow i'm getting this on a shared hosting server, on one of the domains: Unable to generate the web server configuration file on the host because of the following errors: nginx: [warn] duplicate MIME type "text/html" in /etc/nginx/nginx.conf:45 nginx: [emerg] open() "/var/www/vhosts/partydayandnight.ro/statistics/logs/proxy_access_log" failed (24: Too many open files) nginx: configuration file /etc/nginx/nginx.conf test failed Please resolve the errors in web server configuration templates and generate the file again. why is this appearing and what troubles may it cause? what can i do to get this errors fixed? thank you!

    Read the article

  • Apache2 Enabling Includes module causes svn access to quit working

    - by Matthew Talbert
    I have dav_svn installed to provide http access to my svn repos. The url is directly under root, eg mywebsite.com/svn/individual-repo. This setup has been working great for some time. Now, I need SSI (server-side includes) for a project, so I enabled this module with a2enmod include. Now, tortoisesvn can't access the repo; it always returns a 301 permanent redirect. Some playing with it reveals I can access it in a browser if I'm sure to include the trailing / but it still doesn't work in TortoiseSVN. I've looked at all of the faq's for this problem with TortoiseSVN and apache, and none of them seem to apply to my problem. Anyone have any insight into this problem? I'm running Ubuntu 9.10 with Apache 2.2.12. The only change I've made to my configuration is to enable the includes mod. Here's my dav_svn conf: <Location /svn> DAV svn SVNParentPath /home/matthew/svn AuthType Basic AuthName "Subversion repository" AuthUserFile /etc/subversion/passwd Require valid-user </Location> and here's the relevant part of my virtual host conf: <Location /svn> SetHandler None Order allow,deny Allow from all </Location> Edit: OK, I've discovered that the real conflict is between the include module and basic authentication. That is, if I disable the include module, browse to the subversion repo, enter my user/pass for the basic authentication, I can browse it just fine. It even continues to work after I re-enable the include module. However, if I browse with another browser where I'm not already authenticated, then it no longer works.

    Read the article

  • exim4 - disable autoreplies about "SMTP error from remote mail server after RCPT"

    - by osgx
    Hello I have a setup of exim4 on domain1 in front of other server, domain2 (with sendmail). Second server have no direct access to internet, so domain1 is MX for domain2. And domain2 is set as hubbed_host in the exim4 on domain1. When spammer sends message for no_such_user@domain2, its sendmail do a reject: 550 5.1.1 <no_such_user@domain2>... User unknown Then, exim4 at domain1 do an auto-reply like this: This message was created automatically by mail delivery software. A message that you sent could not be delivered to one or more of its recipients. This is a permanent error. The following address(es) failed: no_such_user@domain2 SMTP error from remote mail server after RCPT TO:<no_such_user@domain2>: host 10.0.0.1 [10.0.0.1]: 550 5.1.1 <no_such_user@domain2>... User unknown The spammers uses fake "from" field, and such generated messages are frozen by exim for a long time. How can I disable some or all autoreplies from exim4? Ideally, I want a filter, if message was not delivered with error "User unknown" than don't generate any autoreply from mailer-daemon. Thanks!

    Read the article

  • How do you handle authentication across domains?

    - by William Ratcliff
    I'm trying to save users of our services from having to have multiple accounts/passwords. I'm in a large organization and there's one group that handles part of user authentication for users who are from outside the facility (primarily for administrative functions). They store a secure cookie to establish a session and communicate only via HTTPS via the browser. Sessions expire either through: 1) explicit logout of the user 2) Inactivity 3) Browser closes My team is trying to write a web application to help users analyze data that they've taken (or are currently taking) while at our facility. We need to determine if a user is 1) authenticated 2) Some identifier for that user so we can store state for them (what analysis they are working on, etc.) So, the problem is how do you authenticate across domains (the authentication server for the other application lives in a border region between public and private--we will live in the public region). We have come up with some scenarios and I'd like advice about what is best practice, or if there is one we haven't considered. Let's start with the case where the user is authenticated with the authentication server. 1) The authentication server leaves a public cookie in the browser with their primary key for a user. If this is deemed sensitive, they encrypt it on their server and we have the key to decrypt it on our server. When the user visits our site, we check for this public cookie. We extract the user_id and use a public api for the authentication server to request if the user is logged in. If they are, they send us a response with: response={ userid :we can then map this to our own user ids. If necessary, we can request additional information such as email-address/display name once (to notify them if long running jobs are done, or to share results with other people, like with google_docs). account_is_active:Make sure that the account is still valid session_is_active: Is their session still active? If we query this for a valid user, this will have a side effect that we will reset the last_time_session_activated value and thus prolong their session with the authentication server last_time_session_activated: let us know how much time they have left ip_address_session_started_from:make sure the person at our site is coming from the same ip as they started the session at } Given this response, we either accept them as authenticated and move on with our app, or redirect them to the login page for the authentication server (question: if we give an encrypted portion of the response (signed by us) with the page to redirect them to, do we open any gaping security holes in the authentication server)? The flaw that we've found with this is that if the user visits evilsite.com and they look at the session cookie and send a query to the public api of the authentication server, they can keep the session alive and if our original user leaves the machine without logging out, then the next user will be able to access their session (this was possible before, but having the session alive eternally makes this worse). 2) The authentication server redirects all requests made to our domain to us and we send responses back through them to the user. Essentially, they act as a proxy. The advantage of this is that we can handshake with the authentication server, so it's safe to be trusted with the email address/name of the user and they don't have to reenter it So, if the user tries to go to: authentication_site/mysite_page1 they are redirected to mysite. Which would you choose, or is there a better way? The goal is to minimize the "Yet Another Password/Yet another username" problem... Thanks!!!!

    Read the article

  • Leopard Network Shares and browsing are unreliable

    - by EvilChookie
    I have two macs, running Leopard 10.5.8. One is the 13" MBP connected via WiFi, and the other is a 24" 2008 iMac, connected via ethernet. There are at least another 6-10 machines (windows and mac) awake on the network (with shares) at any given time, yet there are plenty of times where I cannot see any devices/shares in either my "Shared" section in Finder, nor can I see any computers in "Network" in Finder. Restarting doesn't help. I've restarted all the networking gear in the house to no avail. Our network is a series of gigabit switches connected to a D-Link gaming router. I believe we use OpenDNS, and our provider is Cox. I hate having to use "Go - Connect to Server" to browse to commonly used file shares (by IP). I'd like to know why my shares do not always and consistently appear in Leopard. Edit: I ran OnyX this morning, and performed the cleaning and maintenance operations (including disk permissions) on both my Macs, and at least one of my macs has started showing network devices again. (the other is still going). No idea how long this will last. Any ideas as to what is causing this issue, and how to prevent it? Edit 2: Aaaand there the shares go again. So running OnyX is not a permanent or reliable fix for this issue. Edit 3: After a clean reinstall and update, network shares are still unreliable. The SMBClient command mentioned in comments shows me the information it's supposed to show, but the shares do not appear in the shared section. They'll also vanish at random and reappear at random throughout the day.

    Read the article

  • Routing WIFI and LAN for specific traffic

    - by jakebird451
    I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing. EDIT: If I currently have been trying: sudo route flush sudo route add default 192.168.19.1 This gets everything to work for about a minute. But after such minute it "forgets" the routing to WiFi while retaining LAN's (en0) routing. If I unplug and replug my LAN (en0) cable, the process works for another minute.

    Read the article

  • Can I edit the snapshots of websites on most visited sites page in Chrome?

    - by arik
    I saw the previous chain of discussion, but did not find a way to continue the thread - I have found the "Preference" (I have Windows 7), but in that, I did not find clearly what to modify. I did find a section called 'URLs pinned" or something like this, but it did NOT match fully the ones I have. I have activated the 'profile sync' for Chrome - don't know if it has any effect. Can you manually edit the icons of the most visited sites, for the new tab page in Chrome? When you open a new tab in Chrome, I get the 'new page' tab, where I selected the 'most popular', so I have 8 icons with the 8 most popular sites I visited; I can also pin any one of those I see on screen, such that they remain 'permanent' there. We are missing one which would point to, say, "hotmail". So, I was looking for a way to add 'hotmail' to be one of the 8. (and, by the way, we ticked the 'X' on one of those 8, and now it remains grey / shows nothing in it). So, my double-question: How can I add a URL of my choice into one of those 8 spaces? How can I restore usage of the last one?

    Read the article

  • How to avoid Windows Genuine Advantage for an XP update?

    - by hlovdal
    I am about to apply updates to a windows xp installation I have not booted in a couple of years. When going to update.microsoft.com, it forced me first to accept an activex installation and now it wants me to install wga: Windows Update To use this latest version of Windows Update, you will need to upgrade some of its components. This version provides you with the following enhancements to our service: <... useless list of "advantages" ... Details Windows Genuine Advantage Validation Tool (KB892130) 1.1 MB , less than 1 minute The Windows Genuine Advantage Validation Tool enables you to verify that your copy of Microsoft Windows is genuine. The tool validates your Windows installation by checking Windows Product Identification and Product Activation status. Update for Windows XP (KB898461) 477 KB , less than 1 minute This update installs a permanent copy of Package Installer for Windows to enable software updates to have a significantly smaller download size. The Package Installer facilitates the install of software updates for Microsoft Windows operating systems and other Microsoft products. After you install this update, you may have to restart your system. Total: 1.5 MB , less than 1 minute I have heard nothing but bad things about wga, and I absolutely do not want it installed on my system (this answer seems to give some options). Searching for "windows xp" at microsoft's web pages brought up this page which says Windows XP Service Pack 3 Network Installation Package for IT Professionals and Developers Brief Description This installation package is intended for IT professionals and developers downloading and installing on multiple computers on a network. If you're updating just one computer, please visit Windows Update at http://update.microsoft.com . ... File Name: WindowsXP-KB936929-SP3-x86-ENU.exe I am currently downloading this file. Will installing this bring my installation up to date with security updates? What about later updates whenever a new problem is discovered, how can i update without using wga?

    Read the article

  • Why are snapshots considered as temporary backups not real backups?

    - by Samselvaprabu
    I am using VMware ESXi. In our team we use to provide snapshots for long term backup. Then we faced issues like memory spillover and the server got hang up. I started reading in VMware knowledgebase articles and everywhere. Everywhere it was recommended not to have snapshots for a long time. Even VMware advised to keep snapshots for maximum of three days. But our team kept asking us to have at least two permanent snapshots (till deleting the VM). Sometimes we may use the VM for a year). one snapshot is for fresh machine state. (So when we complete testing an application, we will revert back to fresh state and install another application) (If I did not allow that, I may often need to host the VM.) Next snapshot for keeping the VM in some state (maybe they would have found an issue and keep that state for some time. Or they may install prerequisites for the application and keep the machine ready for testing.) Logically, their needs seems to be fair. But if I allow that, I am to permit them to hold the snapshots for long time. We are not using our VM as a mail server or database server. Why is keeping snapshots for long time having an adverse effect? Why are snapshots considered as temporary backups, not real backups?

    Read the article

  • Samba server NETBIOS name not resolving, WINS support not working

    - by Eric
    When I try to connect to my CentOS 6.2 x86_64 server's samba shares using address \\REPO (NETBIOS name of REPO), it times out and shows an error; if I do so directly via IP, it works fine. Furthermore, my server does not work correctly as a WINS server despite my samba settings being correct for it (see below for details). If I stop the iptables service, things work properly. I'm using this page as a reference for which ports to use: http://www.samba.org/samba/docs/server_security.html Specifically: UDP/137 - used by nmbd UDP/138 - used by nmbd TCP/139 - used by smbd TCP/445 - used by smbd I really really really want to keep the secure iptables design I have below but just fix this particular problem. SMB.CONF [global] netbios name = REPO workgroup = AWESOME security = user encrypt passwords = yes # Use the native linux password database #passdb backend = tdbsam # Be a WINS server wins support = yes # Make this server a master browser local master = yes preferred master = yes os level = 65 # Disable print support load printers = no printing = bsd printcap name = /dev/null disable spoolss = yes # Restrict who can access the shares hosts allow = 127.0.0. 10.1.1. [public] path = /mnt/repo/public create mode = 0640 directory mode = 0750 writable = yes valid users = mangs repoman IPTABLES CONFIGURE SCRIPT # Remove all existing rules iptables -F # Set default chain policies iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP # Allow incoming SSH iptables -A INPUT -i eth0 -p tcp --dport 22222 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22222 -m state --state ESTABLISHED -j ACCEPT # Allow incoming HTTP #iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT #iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # Allow incoming Samba iptables -A INPUT -i eth0 -p udp --dport 137 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 137 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p udp --dport 138 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 138 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 139 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 139 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 445 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 445 -m state --state ESTABLISHED -j ACCEPT # Make these rules permanent service iptables save service iptables restart**strong text**

    Read the article

  • Pfsense 2.1 OpenVPN can't reach servers on the LAN

    - by Lucas Kauffman
    I have a small network set up like this: I have a Pfsense for connecting my servers to the WAN, they are using NAT from the LAN - WAN. I have an OpenVPN server using TAP to allow remote workers to be put on the same LAN network as the servers. They connect through the WAN IP to the OVPN interface. The LAN interface also servers as the gateway for the servers to get internet connection and has an IP of 10.25.255.254 The OVPN Interface and the LAN interface are bridged in BR0 Server A has an IP of 10.25.255.1 and is able to connect the internet Client A is connecting through the VPN and is assigned an IP address on its TAP interface of 10.25.24.1 (I reserved a /24 within the 10.25.0.0/16 for VPN clients) Firewall currently allows any-any connection OVPN towards LAN and vice versa Currently when I connect, all routes seem fine on the client side: Destination Gateway Genmask Flags Metric Ref Use Iface 300.300.300.300 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.25.0.0 10.25.255.254 255.255.0.0 UG 0 0 0 tap0 10.25.0.0 0.0.0.0 255.255.0.0 U 0 0 0 tap0 0.0.0.0 300.300.300.300 0.0.0.0 UG 0 0 0 eth0 I can ping the LAN interface: root@server:# ping 10.25.255.254 PING 10.25.255.254 (10.25.255.254) 56(84) bytes of data. 64 bytes from 10.25.255.254: icmp_req=1 ttl=64 time=7.65 ms 64 bytes from 10.25.255.254: icmp_req=2 ttl=64 time=7.49 ms 64 bytes from 10.25.255.254: icmp_req=3 ttl=64 time=7.69 ms 64 bytes from 10.25.255.254: icmp_req=4 ttl=64 time=7.31 ms 64 bytes from 10.25.255.254: icmp_req=5 ttl=64 time=7.52 ms 64 bytes from 10.25.255.254: icmp_req=6 ttl=64 time=7.42 ms But I can't ping past the LAN interface: root@server:# ping 10.25.255.1 PING 10.25.255.1 (10.25.255.1) 56(84) bytes of data. From 10.25.255.254: icmp_seq=1 Redirect Host(New nexthop: 10.25.255.1) From 10.25.255.254: icmp_seq=2 Redirect Host(New nexthop: 10.25.255.1) I ran a tcpdump on my em1 interface (LAN interface which has the IP of 10.25.255.254) tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on em1, link-type EN10MB (Ethernet), capture size 96 bytes 08:21:13.449222 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 10, length 64 08:21:13.458211 ARP, Request who-has 10.25.255.1 tell 10.25.24.1, length 28 08:21:14.450541 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 11, length 64 08:21:14.458431 ARP, Request who-has 10.25.255.1 tell 10.25.24.1, length 28 08:21:15.451794 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 12, length 64 08:21:15.458530 ARP, Request who-has 10.25.255.1 tell 10.25.24.1, length 28 08:21:16.453203 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 13, length 64 So traffic is reaching the LAN interface, but it's not getting passed it. But no answer from the 10.25.255.1 host. I'm not sure what I'm missing.

    Read the article

  • Replacing local home server with VPS: Suggestions?

    - by CamronBute
    So right now, I'm running an old box with a 2TB HDD in it. I use this as a file server for the home network, as well as a box for downloading large files which are synced via Dropbox. Lots of other tinkering things, too. Basically, I'm sick of paying extra for the power and having to worry about drive failures and whatnot. I'd rather get a remote server, let someone else manage it and provide access from the Internet. So, I've been looking for a Windows VPS that would give me access to install things and tinker, and I'm having a problem finding a host that offers more than 100GB of hard drive space. If they do offer a package with 100GB of storage, everything else is waaayyyy more than what I actually need. The idea is to create a permanent VPN connection from the cloud server to my home network to provide a transparent solution so I'm not having to go to lengths to transfer files or whatnot. I think a VPS solution will allow me to do this. I would like 1TB of storage space, minimum 100Mbps Internet connection, minimum 250GB bandwidth, admin access. Anyone have anything? Or am I being unreasonable? If I am, why?

    Read the article

  • PS/2 to USB adapter doesn't work with Model M keyboard

    - by mickburkejnr
    I bought a server about 3 months ago from a friend, and I have only had time to tinker with it in the last week. I noticed that this server doesn't have any PS/2 ports, which meant configuring it was near impossible. I don't have any USB keyboards in the house, I only have an IBM Model M keyboard (built 1994) and another IBM keyboard that was built circa 2001. Both of them have PS/2 connections. I bought an adapter off eBay, and when I used it with the Model M keyboard the three lights on the keyboard flashed for a split second, but then the keyboard is then unresponsive. I can bash away at the keys for ages and nothing will happen. The same applies to the later built IBM keyboard. What could I do to make the adapter work? I am getting the loan of a USB keyboard in two weeks time, but I'd like a more permanent solution without having to rely on getting the loan of a keyboard every time I have to perform maintenance on the server. And as I already have two keyboards which work fine and I like using, I don't really want to have to buy another keyboard just for use on the server.

    Read the article

  • Networking DOS within Windows 7 XP Mode, with a Windows XP/7 Networked Share

    - by theonlylos
    For awhile now, one of my clients has been stuck with Corel Paradox 4.0 (it used to be the biggest database system in the DOS days, until Microsoft released Access in the early 90's) so for awhile I've managed to keep it on life support on Windows XP for a few years, however since switching to Windows 7 x64, I've had to resort to using XP Mode as the sandbox to keep it up and running. While I am able to run Paradox as usual in XP Mode, I'm having a serious issue where if I try connecting the install to the network share (which is located on the Windows 7 portion of the system), Paradox keeps exiting because it says the serial number is invalid. Now, I know for a fact that this is an issue with the virtual loopback adapter and also having the VM linked to the physical ethernet adapter -- and while I have solved this issue before, most of my fixes have been bandages since after a few weeks the issue pops up again. Long story short, I wanted to ask if there is a permanent way to link a DOS program to a network share address. For example, when I try doing \tsclient\paradox (the Windows 7 Address) I keep getting an error saying I need a valid network address. I've tried mapping that folder to various drive letters such as P:\Paradox -- but for some reason that keeps failing over time. For what it's worth, Paradox uses a .SOM file to store the network settings, however it isn't editable in Notepad but rather it's controlled by a wizard in Paradox. But if that extension rings any bells, I'd welcome any insights.

    Read the article

  • Using IIS7 as a reverse proxy

    - by Jon
    My question is pretty much identical to the question listed but they did not get an answer as they ended up using Linux as the reverse proxy. http://serverfault.com/questions/55309/using-iis7-as-a-reverse-proxy I need to have IIS the main site and linux (Apache) being the proxied site(s). so I have site1.com (IIS7) site2.com (Linux Apache) they have subdomains of sub1.site1.com sub2.site1.com sub3.site2.com I want all traffic to go to site1.com and to say anything that is site2.com should be proxied to linux box on internal network, (believe ARR can do this but not sure how). I can not have it running as Apache doing the proxying as I need IIS exposed directly. any and all advice would be great. EDIT I think this might help me: <rule name="Canonical Host Name" stopProcessing="true"> <match url="(.*)" /> <conditions> <add input="{HTTP_HOST}" negate="true" pattern="^cto\.com$" /> <add input="{HTTP_HOST}" negate="true" pattern="^antoniochagoury\.com$" /> <add input="{HTTP_HOST}" negate="true" pattern="www.antoniochagoury\.com$" /> </conditions> <action type="Redirect" url="http://www.cto20.com/{R:1}" redirectType="Permanent" /> </rule> from: http://www.cto20.com/post/Tips-Tricks-3-URL-Rewriting-Rules-Everyone-Should-Use.aspx I will have a look at this when I have access to the IIS7 box. Thanks

    Read the article

  • Will Parallel-port dongle work on USB-to-Parallel Adapter?

    - by Gary M. Mugford
    We have a niche program running on a Win2K laptop that uses a security dongle connected to a parallel port for authentication. The laptop is getting creaky and I spent a frustrating night last night shopping various websites for a new laptop that had a parallel port. Seems I'm about three years late [G]. The question I have, is, if I buy a new(ish) laptop and use a USB-to-Parallel Port adapter, will the security dongle work? I know I'm not being specific about the app, but it's one most people wouldn't have heard of anyways. I've been guessing the answer to my question is no, since the app won't know to send a request out to the non-existent port. But, if the process actually is that the dongle sends a message INTO the computer every now and then, then it might work. And, I'm not sure whether the dongle is only needed at program startup time or randomly. The dongle is a 'permanent' addition to the old laptop. This is all about the money. We can have a newly-updated version of the program (which won't add any features we need) for the princely sum of $2700. Or we can spend $500 on a refurbed laptop still running WinXP, add a 30 buck adapter and keep the same solid, stolid performance we've come to appreciate. But it all comes down to the dongle behaviour. Oh, and a dock won't work. The whole laptop issue is about moving about the various nooks and crannies of the building with laptop in hand. Thanks for any suggestions/guidance. GM

    Read the article

  • How do I determine whether this email bounce is my fault?

    - by David Zaslavsky
    I use Google Apps to handle email for my personal website, so I have an email address [email protected] through that, and I also have a Gmail account [email protected]. Now, I've been trying to send emails to a particular recipient who shall be known as [email protected]. When I send the email from my Gmail account with the @gmail.com address, it works fine. However, when I send it from my Google Apps account with the @ellipsix.net address, I get a bounce message which includes the following text: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 mail server permanently rejected message (#5.3.0) (state 17). The bounce message suggests that it is up to the mail administrator of the recipient domain example.com to fix the problem, whatever it is. But I would like to be as sure as possible that nothing needs to be fixed on my end. I already have DKIM signatures enabled for my domain, and I have published an SPF DNS record. Is there something else I should check or do, or can I be confident that it's up to the recipient to fix this issue? Does the "state 17" in the bounce message mean something relevant? I've included my domain name in the question so people who know more than me about this stuff can independently check the relevant DNS records or other information. This other question seems similar, but I've already investigated everything suggested in the answers there (except for contacting Google, which I don't want to do unless I suspect it's their issue to fix).

    Read the article

  • Suspected Router problems, [closed]

    - by jordon_user
    I am new to this forum. I appreciate any help you can offer. I have been troubleshooting an error with both my WIRED Internet Connection I have 3 desktops running through this working connection (Router) with no problems. Two computers, one laptop and desktop experience the issue. If I connect directly to the Modem, on either, no problem on the internet. Through the Router, my computer connects for a period of time but if ever awaking my comp, or restarting, the yellow explanation mark returns. The only way I can get the connection up = cmd. ipconfig /release, ipconfig /renew. This constant command is annoying and was hoping for a permanent fix. Audio is also not working. I know its likely a driver error, but its an old comp we put together and if there's an easy fix itd be great to hear from you! If you need any more info just let me know. Thanks! THanks guys!

    Read the article

  • Need to get SMTP server on MS Server 2003

    - by Matt Dawdy
    Long story short, client paid networking company to move their website in house. Now I have to figure out how to email out from their website even though they don't have an SMTP server. At least until I install one. Their email is hosted with Gmail right now (the client's domain through Google App for Your Domain). I changed my code to connect as one of their users "[email protected]" and send email. Worked great for about 12 hours. All of a sudden none of the automated emails are going out now, and google is sending the emails back saying that it is a permanent failure and Message Rejected. The link they direct me to, http://mail.google.com/support/bin/answer.py?answer=69585 is telling me that our emails look like spam. They aren't. They are emails we send to out clients about the status of their applications. Seriously, they are NOT spam. So...long story short is out the window, sorry...but I need to get an SMTP server setup inside their domain that I can send emails out of. This thing won't need to receive emails ever, and really only needs 1 email account customercare. What can I do? Will I have to have the networking company open a port in the firewall? Is there one built into Server 2003?

    Read the article

  • What is consuming memory?

    - by Milan Babuškov
    Feel free to change the question title. I have a VPS with standard LAMP stack and a busy website. Operating system is CentOS 5.5. Virtualization is done with VMWare. My server gets real slow about every 6 hours. Logging into it I see that 1.6GB of RAM is consumed. However, listing the active processes does not explain the problem. Can anyone make any sense of this? "free" shows this: total used free shared buffers cached Mem: 2059456 2049280 10176 0 14780 380968 -/+ buffers/cache: 1653532 405924 Swap: 2096472 96 2096376 While this is output of "ps": [root@vmi29 /]# ps aux USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.0 0.0 10348 688 ? Rs Jun05 0:01 init [3] root 2 0.0 0.0 0 0 ? S< Jun05 0:00 [migration/0] root 3 0.0 0.0 0 0 ? SN Jun05 0:00 [ksoftirqd/0] root 4 0.0 0.0 0 0 ? S< Jun05 0:00 [migration/1] root 5 0.0 0.0 0 0 ? SN Jun05 0:00 [ksoftirqd/1] root 6 0.0 0.0 0 0 ? S< Jun05 0:00 [migration/2] root 7 0.0 0.0 0 0 ? SN Jun05 0:00 [ksoftirqd/2] root 8 0.0 0.0 0 0 ? S< Jun05 0:00 [migration/3] root 9 0.0 0.0 0 0 ? SN Jun05 0:00 [ksoftirqd/3] root 10 0.0 0.0 0 0 ? S< Jun05 0:06 [events/0] root 11 0.0 0.0 0 0 ? S< Jun05 0:00 [events/1] root 12 0.0 0.0 0 0 ? S< Jun05 0:00 [events/2] root 13 0.0 0.0 0 0 ? S< Jun05 0:00 [events/3] root 14 0.0 0.0 0 0 ? S< Jun05 0:00 [khelper] root 31 0.0 0.0 0 0 ? S< Jun05 0:00 [kthread] root 38 0.0 0.0 0 0 ? S< Jun05 0:00 [kblockd/0] root 39 0.0 0.0 0 0 ? S< Jun05 0:00 [kblockd/1] root 40 0.0 0.0 0 0 ? S< Jun05 0:00 [kblockd/2] root 41 0.0 0.0 0 0 ? S< Jun05 0:00 [kblockd/3] root 42 0.0 0.0 0 0 ? S< Jun05 0:00 [kacpid] root 204 0.0 0.0 0 0 ? S< Jun05 0:00 [cqueue/0] root 205 0.0 0.0 0 0 ? S< Jun05 0:00 [cqueue/1] root 206 0.0 0.0 0 0 ? S< Jun05 0:00 [cqueue/2] root 207 0.0 0.0 0 0 ? S< Jun05 0:00 [cqueue/3] root 210 0.0 0.0 0 0 ? S< Jun05 0:00 [khubd] root 212 0.0 0.0 0 0 ? S< Jun05 0:00 [kseriod] root 302 0.0 0.0 0 0 ? S Jun05 0:00 [khungtaskd] root 303 0.0 0.0 0 0 ? S Jun05 0:00 [pdflush] root 304 0.0 0.0 0 0 ? S Jun05 0:01 [pdflush] root 305 0.0 0.0 0 0 ? S< Jun05 0:05 [kswapd0] root 306 0.0 0.0 0 0 ? S< Jun05 0:00 [aio/0] root 307 0.0 0.0 0 0 ? S< Jun05 0:00 [aio/1] root 308 0.0 0.0 0 0 ? S< Jun05 0:00 [aio/2] root 309 0.0 0.0 0 0 ? S< Jun05 0:00 [aio/3] root 515 0.0 0.0 0 0 ? S< Jun05 0:00 [kpsmoused] root 582 0.0 0.0 0 0 ? S< Jun05 0:00 [mpt_poll_0] root 583 0.0 0.0 0 0 ? S< Jun05 0:00 [mpt/0] root 584 0.0 0.0 0 0 ? S< Jun05 0:00 [scsi_eh_0] root 590 0.0 0.0 0 0 ? S< Jun05 0:00 [ata/0] root 591 0.0 0.0 0 0 ? S< Jun05 0:00 [ata/1] root 592 0.0 0.0 0 0 ? S< Jun05 0:00 [ata/2] root 593 0.0 0.0 0 0 ? S< Jun05 0:00 [ata/3] root 594 0.0 0.0 0 0 ? S< Jun05 0:00 [ata_aux] root 610 0.0 0.0 0 0 ? S< Jun05 0:00 [kstriped] root 631 0.0 0.0 0 0 ? S< Jun05 0:05 [kjournald] root 656 0.0 0.0 0 0 ? S< Jun05 0:00 [kauditd] root 689 0.0 0.0 13364 928 ? S<s Jun05 0:00 /sbin/udevd -d root 2123 0.0 0.0 0 0 ? S< Jun05 0:00 [kmpathd/0] root 2124 0.0 0.0 0 0 ? S< Jun05 0:00 [kmpathd/1] root 2126 0.0 0.0 0 0 ? S< Jun05 0:00 [kmpathd/2] root 2127 0.0 0.0 0 0 ? S< Jun05 0:00 [kmpathd/3] root 2128 0.0 0.0 0 0 ? S< Jun05 0:00 [kmpath_handlerd] root 2203 0.0 0.0 0 0 ? S< Jun05 0:00 [kjournald] root 2613 0.0 0.0 5908 648 ? Ss Jun05 0:00 syslogd -m 0 root 2617 0.0 0.0 3804 424 ? Ss Jun05 0:00 klogd -x root 2707 0.0 0.0 10760 372 ? Ss Jun05 0:02 irqbalance apache 2910 0.5 0.6 213964 12912 ? S 00:22 0:07 /usr/sbin/httpd dbus 3011 0.0 0.0 21256 904 ? Ss Jun05 0:00 dbus-daemon --system root 3025 0.0 0.0 3800 576 ? Ss Jun05 0:00 /usr/sbin/acpid 68 3038 0.0 0.2 31152 4336 ? Ss Jun05 0:01 hald root 3039 0.0 0.0 21692 1176 ? S Jun05 0:00 hald-runner 68 3046 0.0 0.0 12324 856 ? S Jun05 0:00 hald-addon-acpi: listening on acpid socket /var/run/acpid.s 68 3052 0.0 0.0 12324 856 ? S Jun05 0:00 hald-addon-keyboard: listening on /dev/input/event0 root 3105 0.0 0.0 62624 1212 ? Ss Jun05 0:00 /usr/sbin/sshd root 3264 0.0 0.0 74820 1156 ? Ss Jun05 0:00 crond root 3292 0.0 0.0 18416 472 ? S Jun05 0:00 /usr/sbin/smartd -q never root 3300 0.0 0.0 3792 480 tty2 Ss+ Jun05 0:00 /sbin/mingetty tty2 root 3301 0.0 0.0 3792 480 tty3 Ss+ Jun05 0:00 /sbin/mingetty tty3 root 3302 0.0 0.0 3792 484 tty4 Ss+ Jun05 0:00 /sbin/mingetty tty4 root 3304 0.0 0.0 3792 480 tty5 Ss+ Jun05 0:00 /sbin/mingetty tty5 root 3306 0.0 0.0 3792 480 tty6 Ss+ Jun05 0:00 /sbin/mingetty tty6 apache 5158 0.4 0.5 211896 11848 ? S 00:28 0:04 /usr/sbin/httpd apache 5519 0.4 0.5 211896 11992 ? S 00:29 0:03 /usr/sbin/httpd root 5649 0.0 0.0 63848 1184 pts/0 S Jun05 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --soc mysql 5696 2.1 1.9 411060 40392 pts/0 Rl Jun05 2:01 /usr/libexec/mysqld --basedir=/usr --datadir=/var/lib/mysql apache 5943 0.4 0.5 211896 12000 ? S 00:30 0:03 /usr/sbin/httpd apache 5976 0.6 0.5 211896 11792 ? S 00:30 0:04 /usr/sbin/httpd apache 6073 0.4 0.5 211896 11208 ? S 00:31 0:03 /usr/sbin/httpd apache 6122 0.4 0.5 211896 11848 ? S 00:31 0:03 /usr/sbin/httpd apache 6128 0.3 0.5 211896 11940 ? S 00:31 0:02 /usr/sbin/httpd apache 6159 0.5 0.5 211896 11872 ? S 00:31 0:04 /usr/sbin/httpd apache 6636 0.4 0.6 213960 13444 ? S 00:32 0:02 /usr/sbin/httpd apache 6787 0.3 0.5 211884 11308 ? S 00:33 0:02 /usr/sbin/httpd apache 6796 0.4 0.5 211884 12024 ? S 00:33 0:02 /usr/sbin/httpd apache 6801 0.3 0.5 211896 11920 ? S 00:33 0:01 /usr/sbin/httpd apache 6804 0.4 0.5 211884 11848 ? S 00:33 0:02 /usr/sbin/httpd apache 6825 0.4 0.5 211896 11972 ? S 00:33 0:02 /usr/sbin/httpd apache 6866 0.3 0.5 210860 11044 ? S 00:33 0:01 /usr/sbin/httpd apache 6870 0.2 0.5 211896 11108 ? S 00:33 0:01 /usr/sbin/httpd apache 6872 0.3 0.5 211896 11900 ? S 00:33 0:01 /usr/sbin/httpd apache 6993 0.3 0.5 211896 11836 ? S 00:33 0:02 /usr/sbin/httpd apache 6994 0.3 0.5 211896 11792 ? S 00:33 0:01 /usr/sbin/httpd apache 7136 0.2 0.5 211896 11432 ? S 00:34 0:01 /usr/sbin/httpd apache 7143 0.2 0.5 210860 11052 ? S 00:34 0:01 /usr/sbin/httpd apache 7145 0.2 0.5 211896 11136 ? S 00:34 0:01 /usr/sbin/httpd apache 7266 0.2 0.6 213952 12748 ? S 00:34 0:01 /usr/sbin/httpd apache 7299 0.2 0.5 211884 11276 ? S 00:34 0:01 /usr/sbin/httpd apache 7311 0.2 0.5 211884 11300 ? S 00:34 0:01 /usr/sbin/httpd apache 7313 0.3 0.5 211884 11876 ? S 00:34 0:01 /usr/sbin/httpd apache 7345 0.2 0.5 210872 11100 ? S 00:34 0:01 /usr/sbin/httpd apache 7349 0.2 0.5 210860 11008 ? S 00:34 0:01 /usr/sbin/httpd apache 7350 0.2 0.5 211896 11832 ? S 00:34 0:01 /usr/sbin/httpd apache 7351 0.1 0.5 211884 11072 ? S 00:34 0:00 /usr/sbin/httpd apache 7352 0.2 0.5 210872 11096 ? S 00:34 0:01 /usr/sbin/httpd apache 7449 0.1 0.5 210860 11020 ? S 00:35 0:00 /usr/sbin/httpd root 7490 0.3 0.0 0 0 ? S Jun05 3:11 [vmmemctl] root 7597 0.0 0.0 72656 1260 ? Ss Jun05 0:06 /usr/lib/vmware-tools/sbin64/vmware-guestd --background /va apache 7720 0.1 0.5 210860 10748 ? S 00:36 0:00 /usr/sbin/httpd apache 7726 0.1 0.4 209836 9304 ? R 00:36 0:00 /usr/sbin/httpd apache 7727 0.1 0.5 210860 10916 ? S 00:36 0:00 /usr/sbin/httpd apache 7731 0.1 0.5 210860 10780 ? S 00:36 0:00 /usr/sbin/httpd apache 7732 0.3 0.5 210860 10916 ? S 00:36 0:01 /usr/sbin/httpd apache 7733 0.1 0.5 210872 11000 ? S 00:36 0:00 /usr/sbin/httpd apache 7735 0.1 0.5 211884 11048 ? S 00:36 0:00 /usr/sbin/httpd apache 7761 0.1 0.5 210860 10552 ? S 00:36 0:00 /usr/sbin/httpd apache 7776 0.1 0.4 209836 8648 ? R 00:37 0:00 /usr/sbin/httpd apache 7790 0.2 0.3 208812 7724 ? R 00:40 0:00 /usr/sbin/httpd apache 7800 0.2 0.3 208812 8088 ? R 00:40 0:00 /usr/sbin/httpd root 7801 0.0 0.0 3792 484 tty1 Ss+ 00:41 0:00 /sbin/mingetty tty1 apache 7820 0.2 0.3 208812 7552 ? R 00:41 0:00 /usr/sbin/httpd apache 7834 0.2 0.3 207788 6756 ? R 00:42 0:00 /usr/sbin/httpd apache 7864 0.2 0.2 207788 6148 ? R 00:42 0:00 /usr/sbin/httpd apache 7872 0.3 0.2 207788 5856 ? R 00:43 0:00 /usr/sbin/httpd apache 7874 2.5 0.3 207788 6336 ? R 00:43 0:00 /usr/sbin/httpd root 7875 0.3 0.0 63844 1056 ? S 00:43 0:00 sh -c lsb_release -sd 2>/dev/null root 7879 1.6 0.0 65604 964 pts/0 R+ 00:43 0:00 ps aux root 16316 0.0 0.1 90128 3272 ? Ss Jun05 0:00 sshd: milanb [priv] milanb 16358 0.0 0.0 90128 1752 ? S Jun05 0:00 sshd: milanb@pts/0 milanb 16360 0.0 0.0 66076 1480 pts/0 Ss Jun05 0:00 -bash root 16875 0.0 0.0 101068 1324 pts/0 S Jun05 0:00 su - root 16877 0.0 0.0 66184 1692 pts/0 S Jun05 0:00 -bash root 24373 0.0 0.3 206764 7348 ? Rs Jun05 0:01 /usr/sbin/httpd

    Read the article

  • Email bouncing sent from Google

    - by davidmck
    I'm hoping someone here has an idea of where to look next. We have a domain we support which has email sent to it from one particular user bounce with the following message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 Unrouteable address (state 14). We only have reports of bouncing form this one particular user (who is someone we don't support - except they'd like to be able to contact our customer and we're trying to figure out if the problem is on our end). Many people can successfully send to this domain and the user who is getting bounce messages can send to other domains that we support (so it's clearly something specific with the princetonscoop.com domain and not our setup in general). I've reviewed the MX records multiple times and the server logs don't show a connection which generates this error (in fact this error is not one that our mail server would ever return). So it appears that google is contacting a different mail server for some reason. I have tested sending from my gmail account and that works. I believe the sender is using a google-apps account (the account they are using is from their own domain, not a gmail account). Any ideas on what might be happening here or what to test/investigate next? Thanks.

    Read the article

< Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >