Search Results

Search found 42982 results on 1720 pages for 'web clips'.

Page 1531/1720 | < Previous Page | 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538  | Next Page >

• How to host an ssh server?

  - by balki

  Hi, I have a broadband internet connection. I have an wireless modem (Airtel India). I don't have a static ip address. I want to host a ssh/web/ftp server to be visible to the outside world just for testing and learning purpose so I can ask my friend to connect to my current ip address and test. My modem has an admin interface which allows to port forward and open ports. I set up ssh server as shown and checked if port 22 is open using this website , Port Scan And port 22 is open. I have an openssh server running and it works if i do, ssh [email protected] which is my local ip address but doesn't work if i do ssh [email protected] where 122.xx.xx.xx is my external ip address of my modem which i checked from whatismyipaddress.com. Since it looks like the port is open, I wonder if there is some setting I need to change in my server config to expose my server. How should I go about solving this?

  Read the article

• Hard drive degredation from large memory usage and paging files?

  - by Stephen R

  I've had a question(s) regarding computer degradation going through my head for a while and haven't found many good resources for researching it. 1) First off, when is the virtual RAM/paging file on a hard drive used by Windows? Is it used when the RAM is full? Or does it use the Virtual RAM/paging file as intermediate caching between the RAM and actual hard drive space all the time? 2) If I were to run many applications on my computer at the same time and have a bad habit of doing this for the entire lifetime of the computer, does it use more of the virtual RAM/paging file than if I were to have fewer programs running? Just to note, the RAM never fills up on my computer but it is used heavily. 3) By extension of question 2, if the virtual RAM/paging file is used more heavily, would that result in rapid hard drive degradation? I have seen a pattern among all of the computers that I have owned or used in the past 5 years. I am the kind of person to leave my web browser up with 40 tabs among other programs which will eat up 40% of my memory typically. Over time my computer will slow down, browsers start crashing, programs start seizing up or crashing themselves, eventually the computer becomes essentially unusable. I have been trying to rack my mind to come up with a solution other than to purchase a new PC to have it die on me in the next couple years as well. This is the only thought that has come to mind that might have a simple hardware fix...Windows ReadyBoost...Maybe? I'd like to be able to discuss this so I can learn something about all of the above. Thanks.

  Read the article

• Trouble with port 80 nating (XenServer to WebServer VM)

  - by Lain92

  I have a rent server running XenServer 6.2 I only have 1 public IP so i did some NAT to redirect ports 22 and 80 to my WebServer VM. I have a problem with the port 80 redirection. When i use this redirection, i can get in the WebServer's Apache but this server lose Web access. I get this kind of error : W: Failed to fetch http://http.debian.net/debian/dists/wheezy/main/source/Sources 404 Not Found [IP: 46.4.205.44 80] but i can ping anywhere. XenserverIP:80 redirected to 10.0.0.2:80 (WebServer). This is the port 80 redirection part of my XenServer iptables : -A PREROUTING -i xenbr1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 10.0.0 .2:80 -A INPUT -i xenbr1 -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT COMMIT What is wrong in my configuration? Is there a problem with XenServer? Thanks for your help ! Edit : Here is my iptables full content : *nat :PREROUTING ACCEPT [51:4060] :POSTROUTING ACCEPT [9:588] :OUTPUT ACCEPT [9:588] -A PREROUTING -p tcp -m tcp --dport 1234 -j DNAT --to-destination 10.0.0.2:22 -A PREROUTING -i xenbr1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 10.0.0 .2:80 -A POSTROUTING -s 10.0.0.0/255.255.255.0 -j MASQUERADE COMMIT *filter :INPUT ACCEPT [5434:4284996] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [5014:6004729] -A INPUT -i xenbr1 -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT COMMIT Update : I have a second server with 10.0.0.3 as IP and it has the same problem that 10.0.0.2 has.

  Read the article

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• Why can't I get out of display mirror mode?

  - by Roy Smith

  I've been running Ubuntu (10.04.1 LTS, 64-bit) for a while and just replaced my hardware with a faster machine with an ATI Radeon HD 5700 video card. I've got twin 1920 x 1080 displays. I downloaded the latest driver (ati-driver-installer-10-9-x86.x86_64.run) from the ATI web site and installed that. I've gone through a few rounds of playing with /etc/X11/xorg.conf, and can't get things right. At the moment, it's in display mirroring mode, and I can't figure out how to get it out of mirror mode. If I run Monitor Preferences, there's a "Same image in all monitors" checkbox. If I uncheck that, the little preview window switches to show two monitors. When I click Apply, it asks me to log out and log back in again. When I do that, I'm right back to mirrored mode. What's really weird is that I'm currently running a copy of xorg.conf from a coworker's machine. He's got identical hardware, and his display works fine. So, I'm inclined to think there's something else going on other than the conf file. Any ideas what might be wrong?

  Read the article

• Technology mash: is this possible?

  - by Jon Story

  I'm in the process of setting up my own DNS+hosting on a couple of VPS and my home machines, mostly for academic/learning purposes, but also for convenient accessing of my files, hosting my personal websites, private git repositories etc. I've got a main web server with DNS, and a slave DNS server. I've also got a couple of machines at home doing file hosting, video streaming and all that fun stuff. I'm intending to use my VPS's to provide myself with a dynamic DNS system so that I can point mydomain.com at my DNS servers, with home.mydomain.com going into my home network via a raspberry pi. HOWEVER.... I've not got access to the network infrastructure at home (rented accommodation with managed internet), so I can't forward the ports on the router to my own machines. As such, I'm wondering if it's possible to route all the traffic via an SSH/HTTP tunnel through one of the VPS? My plan is to have the raspberry pi provide a VPN into my home network. The raspberry pi uses SSH to connect to the VPS, and the VPS forwards any traffic to home.mydomain.com via the tunnel to the raspberry pi. Is this even possible, and how do I go about it? I don't mind getting my hands dirty with coding and low level tools, I'm just not sure where to start or what the best way to go about it is.

  Read the article

• Hotmail mail delivery issue (spam)

  - by chaochito

  Hello, I am running a Postfix server in a dedicated server in a Linux environment (centOS 5.3) for a social networking web application and are experiencing deliverability issues with Hotmail (I can send mails to Gmail, Yahoo, Aol in inbox). I only send legit mails for registered users (notifications). I have SPF, DK and DKIM setup. I pass the Sender ID test when mailing to [email protected] but we have "X-Auth-Result : None" only in Hotmail headers and no X-SID-Result:Pass. We have been enrolled in their program for more than 2 weeks and normally when you apply to their Sender ID program you are supposed to have X-SID-Result:Pass and X-Auth-Result:Pass. I contacted Hotmail about the issue and they told me that my domain looks like added to Sender ID in their system this is beyond their support and asked me to contact my ISP. As you can imagine, my ISP has no clue about that either. I don't really know what could be wrong... Mails are currently filtered as spam and we would like to be able to have them landing in inbox.

  Read the article

• Unable to connect to server after a certain amount of time

  - by Troy

  I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

  Read the article

• Delayed internet access

  - by Joel Coel

  When I (and presumably my users) first start up or log in to my computer I can't get internet access until several minutes after logging in. Internet pages like serverfault.com will time out. During this time I can access internal web servers. Sometimes pinging the gateway seems to fix the problem. I'm using Windows 7 on this machine with wifi, and the problem seems limited to the wifi network, which is on a separate vlan. The wired network does not share the problem, but I know it's not the wifi connection itself because the internal sites work. The wifi access point is attached to a 3Com 4200 switch, with the port set for vlan 2 untagged, vlan 1 tagged. The 4200 has a fiber connection to a 3Com 4900SX fiber switch that acts almost as a router here. The fiber connection is vlan 1 untagged vlan 2 tagged at both ends. The gateway is then attached to a different 4200 (vlan 1 untagged, vlan 2 tagged) that has a similar fiber connection to the 4900SX. vlan 2 has 192.168.8.0/22 IPs, vlan 1 has 10.1.0.0/16 IPs. The 4900SX has an interface for both vlans (10.1.1.1/192.168.8.1), as does the gateway (10.1.1.5/192.168.8.5). There is one dchp server for both vlans on the same switch as the gateway. It chooses a dhcp scope based on the interface used by the 4900sx to forward the dhcp request. There is also a network access list on the 4900sx set to deny all vlan2 traffic to any 10.1.x.x host, with exceptions made for a few servers, including dhcp, 4900sx, and the gateway. I think that about covers it. Any ideas on why internet access would be delayed like this?

  Read the article

• Apache2 default vhost in alphabetical order or override with _default_ vhost?

  - by benbradley

  I've got multiple named vhosts on an Apache web server (CentOS 5, Apache 2.2.3). Each vhost has their own config file in /etc/httpd/vhosts.d and these vhost config files are included from the main httpd conf with... Include vhosts.d/*.conf Here's an example of one of the vhost confs... NameVirtualHost *:80 <VirtualHost *:80> ServerName www.domain.biz ServerAlias domain.biz www.domain.biz DocumentRoot /var/www/www.domain.biz <Directory /var/www/www.domain.biz> Options +FollowSymLinks Order Allow,Deny Allow from all </Directory> CustomLog /var/log/httpd/www.domain.biz_access.log combined ErrorLog /var/log/httpd/www.domain.biz_error.log </VirtualHost> Now I when anyone tries to access the server directly by using the public IP address, they get the first vhost specified in the aggregated config (so in my case it's alphabetical order from the vhosts.d directory). Anyone accessing the server directly by IP address, I'd like them to just get an 403 or a 404. I've discovered several ways to set a default/catch-all vhost and some conflicting opinions. I could create a new vhost conf in vhosts.d called 000aaadefault.conf or something but that feels a bit nasty. I could have a <VirtualHost> block in my main httpd.conf before the vhosts.d directory is included. I could just specify a DocumentRoot in my main httpd.conf What about specifying a default vhost in httpd.conf with _default_ http://httpd.apache.org/docs/2.2/vhosts/examples.html#default Would having a <VirtualHost _default_:*> block in my httpd.conf before I Include vhosts.d/*.conf be the best way for a catch-all?

  Read the article

• Caching/preloading files on Linux into RAM

  - by Andrioid

  I have a rather old server that has 4GB of RAM and it is pretty much serving the same files all day, but it is doing so from the hard drive while 3GBs of RAM are "free". Anyone who has ever tried running a ram-drive can witness that It's awesome in terms of speed. The memory usage of this system is usually never higher than 1GB/4GB so I want to know if there is a way to use that extra memory for something good. Is it possible to tell the filesystem to always serve certain files out of RAM? Are there any other methods I can use to improve file reading capabilities by use of RAM? More specifically, I am not looking for a 'hack' here. I want file system calls to serve the files from RAM without needing to create a ram-drive and copy the files there manually. Or at least a script that does this for me. Possible applications here are: Web servers with static files that get read alot Application servers with large libraries Desktop computers with too much RAM Any ideas? Edit: Found this very informative: The Linux Page Cache and pdflush As Zan pointed out, the memory isn't actually free. What I mean is that it's not being used by applications and I want to control what should be cached in memory.

  Read the article

• Removing trailing slashes in WordPress blog hosted on IIS

  - by Zishan

  I have a WordPress blog hosted in my IIS virtual directory that has all URLs ending with a forward slash. For example: http://www.example.com/blog/ I have the following rules defined in my web.config: <rule name="wordpress" patternSyntax="Wildcard"> <match url="*" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Rewrite" url="index.php" /> </rule> <rule name="Redirect-domain-to-www" patternSyntax="Wildcard" stopProcessing="true"> <match url="*" /> <conditions> <add input="{HTTP_HOST}" pattern="example.com" /> </conditions> <action type="Redirect" url="http://www.example.com/blog/{R:0}" /> </rule> In addition, I tried adding the following rule for removing trailing slashes: <rule name="Remove trailing slash" stopProcessing="true"> <match url="(.*)/$" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Redirect" redirectType="Permanent" url="{R:1}" /> </rule> It seems that the last rule doesn't work at all. Anyone around here who has attempted to remove trailing slashes from WordPress blogs hosted on IIS?

  Read the article

• Unix apt-get doesnt download from nfs locaiton

  - by pravesh

  I have switched to unix from last 3 months and trying to understand install process and in particular apt-get. I am able to successfully install and download the packages when I configure my repository on http location in /etc/apt/sources.list file. e.g. deb http://web.myspqce.com/u/eng/rose/debian-mirror-squeeze-amd64/mirror/ftp.us.debian.org/debian/ squeeze main contrib non-free This command will download(/var/cache/apt/archive) and install the package when i use apt-get install When I change the source location to file instead of http(nfs mount point), the package is getting installed but NOT getting downloaded in /var/cache/apt/archive. deb file:/deb_repository/debian-mirror-squeeze-amd64/mirror/ftp.us.debian.org/debian/ squeeze main contrib non-free Please let me know if there is any configuration or settings that i have to make to let apt-get to both download and install package when i use (nfs)file:/ instead of http:/ in sources.list. To achieve this, I can use apt-get --downlaod-only and then use apt-get install for both download and install in two separate calls, but I want to know why package is not getting downloaded with apt-get install but only getting installed when used with file:/ in sources.list

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• Ubuntu in failed state after upgrade from 10.04 to 10.10 - How to recover?

  - by Harvey

  I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: 1. Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a). 2. gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok] 3. gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ... What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

  Read the article

• Apache returns HTTP 206 for GET /file.mp3

  - by javano

  I am making a get request to an SSL enabled site on apache (so wireshark isn't giving me anything to useful). In my Apache SSL access log I see the following entry: 1.2.3.4 - my.username [15/Nov/2012:16:52:01 +0000] "GET /uploads/file.mp3 HTTP/1.1" 206 534400 "https://site.com/uploads/layla.mp3" "Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/535.19 (KHTML, like Gecko) Ubuntu/12.04 Chromium/18.0.1025.168 Chrome/18.0.1025.168 Safari/535.19" Why is this happening? I'm not familiar with the HTTP 206 response code but searching the Internet I can see it is a partial content GET requests. I understand correctly, my browser is making a partial GET request not for the full file. Is that correct? If so, is this a browser issue or is the web server instructing my browser to do so? I have tested in Firefox also and in both browser, I am not sent the file. If I rename the file to file.jpg I can download it through my browser and rename it to .mp3 and it plays. How can I troubleshoot this issue?

  Read the article

• IP tables blocking access to most hosts but some accesses being logged

  - by epo

  What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

  Read the article

• RAID 10 or RAID 5 for multiple VMs - what is the best choice?

  - by Lars Fastrup

  I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

  Read the article

• Puzzling TCP performance over 3G / UMTS

  - by lemonsqueeze

  I'm using 3G as my primary internet connection, and TCP over this thing is getting more puzzling every day. For example: Downloading from kernel.org is crazy fast: $wget http://www.kernel.org/pub/linux/kernel/v3.0/linux-3.6.8.tar.bz2 increases to ~500kB/s after a few secs ! Some servers are incredibly slow, for instance www.graphic-pc.com:Same thing, downloading a big file with wget it starts at ~30kB/s for a split second, then collapses to 5-10k or even worse. Web browsing is decent but somewhat unreliable. Randomly, a page will take really long to load or even fail to load, but a reload can succeed almost immediately. Now, by chance i started playing with OpenVPN over UDP on top of the 3G connection, and OMG suddenly everything's extremely fast !Same www.graphic-pc.com now shoots at 100-200kB/s ! What's going on here ??? How come it is so much better with the VPN than without ?? And why does graphic-pc.com crawl when kernel.org flies ?Something to do with my tcp stack (or the server), or some buggy router in between ?? Notes: Setup is laptop running Ubuntu Lucid and a Huawei 3G dongle (So direct pppd connection). I can reproduce this pretty much any time during the day and I'm not moving, so it's clearly not cell environment or internet congestion. (although kernel.org without VPN sometimes does worse in the evening, 60kB or so - but still 500kB with VPN !) For 2) wireshark shows retransmitted packets, dup ack's, even out of order sometimes. I've tried playing with different /proc/sys/net/ipv4 parameters (tcp_rmem, window_scaling, tcp_congestion...) doesn't seem to make a difference. Update: Tried under windows 7 (no VPN) with some interesting results: tcp settings : default tcp_optimizer kernel.org : 10 kB/s 20 kB/s graphic-pc.com: 8 kB/s 70 kB/s ! tcp_optimizer turned on ctcp among other things. Have to check what os graphic-pc.com is running, my bet is linux's tcp_westwood and ms ctcp don't mix well here...

  Read the article

• SQL Server Read Locking behavior

  - by Charles Bretana

  When SQL Server Books online says that "Shared (S) locks on a resource are released as soon as the read operation completes, unless the transaction isolation level is set to repeatable read or higher, or a locking hint is used to retain the shared (S) locks for the duration of the transaction." Assuming we're talking about a row-level lock, with no explicit transaction, at default isolation level (Read Committed), what does "read operation" refer to? The reading of a single row of data? The reading of a single 8k IO Page ? or until the the complete Select statement in which the lock was created has finished executing, no matter how many other rows are involved? NOTE: The reason I need to know this is we have a several second read-only select statement generated by a data layer web service, which creates page-level shared read locks, generating a deadlock due to conflicting with row-level exclusive update locks from a replication prcoess that keeps the server updated. The select statement is fairly large, with many sub-selects, and one DBA is proposing that we rewrite it to break it up into multiple smaller statements (shorter running pieces), "to cut down on how long the locks are held". As this assumes that the shared read locks are held till the complete select statement has finished, if that is wrong (if locks are released when the row, or the page is read) then that approach would have no effect whatsoever....

  Read the article

• MX records set up

  - by andrei.troll

  I just want to know how other people set up their MX-entries for mail accounts used with google apps. I work at a local web-hosting firm and we get a lot of tickets from clients who want to set up these settings. I just set them up something like: example.com. 14400 IN MX 10 ALT1.ASPMX.L.GOOGLE.COM. example.com. 14400 IN MX 10 ASPMX4.GOOGLEMAIL.COM. example.com. 14400 IN MX 15 ASPMX5.GOOGLEMAIL.COM. example.com. 14400 IN MX 15 ASPMX2.GOOGLEMAIL.COM. example.com. 14400 IN MX 30 ASPMX3.GOOGLEMAIL.COM. I see another firm (rival one) who sets up way more MX-records ? Roughly, around 10-15 entries. Am I doing something wrong ? More is better in this case ? Is there a secret that I'm not on too ?

  Read the article

• How could one archive all emails sent from employees?

  - by Schnapple

  My client runs a small business. This business has a small number of employees. They are currently hosted through GoDaddy for web and email. For legal reasons the client would like to archive emails sent by their employees. Currently the emails are all done through POP3 so all the email is basically housed in files on individual machines (remember, small business). It's been proposed an inexpensive solution to this would be to have all emails BCC'd to a main account so that conversations with the outside would could be archived and tracked. I have not investigated it myself personally but apparently GoDaddy can do something along these lines for all incoming email but not for outgoing email. Is there a way to set up email accounts for a particular domain to where a specified admin user could be copied on all outgoing email? UPDATE: I've modified the title to reflect employees not users. The goal of this is to archive sent emails for legal reasons. This is something the employees will be cognizant of and on board with. The bottom line here is to basically emulate a feature of a larger-class platform through a smaller, cheaper platform. If the answer is "can't do it, buy an Exchange license" that's fine. My apologies for phrasing this so poorly. I understand why there was so much confusion.

  Read the article

• Configuring MySQL for Power Failure

  - by Farrukh Arshad

  I have absolutely no experience with databases and MySql. Now the problem is I have an embedded device running a MySQL database with a web based application. The problem is when I shutdown my embedded device it just cut off the power, and I can not have a controlled shutdown. Given this situation how can I configure MySql to prevent it from failures and in case of a failure, I should have maximum support to recover my database. While searching this, I came across InnoDB Engine as well as some configuration options to set like sync_binlog=1 & innodb_flush_log_at_trx_commit=1. I have noticed my default Engine is InnoDB and binary logs are also enabled. What are other configurations to make for best possible failure & recovery support. Updated: I will be using InnoDB engine which supports Transactions. My question is how best I can configure it (InnoDB + MySQL) so that it can provide best possible fail-safe as well as crash recovery mechanism. One configuration option I came across is to enable binary logging which InnoDB uses at the time of recovery. Regards, Farrukh Arshad

  Read the article

• Synchronize Active Directory to Database

  - by Tommy Jakobsen

  We are in a situation where we would like to offer our customers to be able to manage their users themselves. It is around 300 customers with up to a total of 10.000 users. Besides creating, updating and removing users, they will very often read information about users for statics and other useful informations available. All this functionality, should be available from an Intranet web page (.NET Framework 4) that the users will access through Citrix or similar. Now the problem is that we would really like the users not to query AD directly for each request, but rather make them hit a database that is synchronized with AD. It would be sufficient to run this synchronization a few time each day (maybe every 5. hour). When they create a user, it should not be available right away, but reviewed and then created within two days (the next step would be to remove this manual review, but that's out of scope for this question). What do you think about this synchronization of AD? Does anyone have any experience with it and is it something that is done in other organizations, where you will have lots of requests which is better handled by a database than AD (I presume)? Are there any techniques out there for writing such a script that synchronizes AD with database tables? My primary concern is the groups/members relations which can be rather complicated. Or are there software that synchronizes AD with a database? Any comments will be much appreciated. Thank you.

  Read the article

• How can I remedy the always-on-top window problem?

  - by GateKiller

  Sorry for the vague title but this one is hard to explain so bear with me please. I'm using Windows Vista at work for web development and sometimes when I Click or Alt-Tab to background window, the window will get focus but it will not be brought to the front. In order to bring the window to the front, I have to click on the applications border (when the resize cursor appears) and the window will then jump to the front. I've had this problem for about a year now and it happens at least a dozen times a day, but it doesn't do this all the time - seems random. I hope I have explained the issue fully (and you've understood it) and would appreciate any constructive answers or comments to solve this problem. Example: If I Alt-Tab from Google Chrome to Notepad and this problem randomly occurs, Google Chrome will remain in front of Notepad, however, I will be able to type text into Notepad while the window is behind Google Chrome. Clicking on Notepad's content area will not bring it to the front but clicking it's window border will. Video Exampe http://vimeo.com/19388998 In this video, I clicked from Google Chome to UltraEdit and chrome stayed in font, but as you can see, I can still type in UltraEdit. I'm starting to believe that this could be a bug in Google Chrome so I'll continue to watch if this between other applications.

  Read the article

< Previous Page | 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538  | Next Page >