Search Results

Search found 14588 results on 584 pages for 'usb drive'.

Page 183/584 | < Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• How to move files in C drive using MoveFileEx APi

  - by rajivpradeep

  Hi, when i use MoveFileEx to move files in C drive, but i am getting the ERROR that ACCESS DENIED. Any solutions int i ; DWORD dw ; String^ Source = "C:\Folder\Program\test.exe" ; String^ Destination = "C:\test.exe"; // move to program Files Folder pin_ptr<const wchar_t> WSource = PtrToStringChars(Source); pin_ptr<const wchar_t> WDestination = PtrToStringChars(Destination); i = MoveFileEx( WSource, WDestination ,MOVEFILE_REPLACE_EXISTING | MOVEFILE_COPY_ALLOWED ) ; dw = GetLastError() ;

  Read the article

• Windows 7 Public Documents Folder - how to move it to drive d: [closed]

  - by Bazza Formez

  Hi, I've just bought a new pc, and it is running Windows 7. I'm wanting to set up all of the documents folders such that they point to folders on a second drive partition (ie. disk D:) so that I have a nice separation of os from docs. I have managed to do this for each user on the machine (by opening up properties for documents folder and changing location). Hwoever, this procedure doesn't seem to work for the public documents folder. I cannot change the location for that one (even though I have administrator privileges). It is greyed out and cannot be changed. Any ideas ? Thanks!!

  Read the article

• PC hangs and reboots from time to time

  - by Bevor

  Hello, I have a very strange problem: Since I have my new PC, I have always had problems with it. From time to time the computer freezes for some seconds and suddendly reboots by itself. I've had this problem since Ubuntu 9.10. The same with 10.04 and 10.10. That's why I don't think it's a software failure because the problem persist too long. It doesn't have anything to do with what I'm doing at this time. Sometimes I listen to music, sometimes I only use Firefox, sometimes I'm running 2 or 3 VMs, sometimes I watch DVD. So it's not isolatable. I could freeze once a day or once a week. I put the PC to the vendor twice(!). The first time they changed my power supply but the problem persisted. The second time they told me that they made some heavy performance tests 50 hours long but they didn't find anything. (How can that be that I have daily freezes with normal usage). The vendor didn't check the hard discs because they used their own disc with Windows. (So they never checked the Linux installation). Yesterday I made some intensive hard disc scans with "SMART" but no errors were found. I ran memtest for 3 times but no errors found. I already had this problem in my old flat, so I doubt that I has something to do with current fluctuation. I already tried another electrical socket and changed to connector strip but the problem persists. At the moment I removed 2 of the RAMs (2x 2GB). In all I have 6GB, 2x2GB and 2x1GB. Could this difference maybe be a problem? Here is a list of my components. I hope that anybody find something I didn't think about yet. And here a list of my components: 1x AMD Phenom II X4 965 Black Edition, 3,4Ghz, Quad Core, S-AM3, Boxed 2x DDR3-RAM 2048MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x DDR3-RAM 1024MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x SATA II Seagate Barracuda 7200.12, 1TB 32MB Cache = RAID 1 1x DVD ROM SATA LG DH16NSR, 16x/52x 1x DVD-+R/-+RW SATA LG GH-22NS50 1x Cardreader 18in1 1x PCI-E 2.0 GeForce GTS 250, Retail, 1024MB 1x Power Supply ATX 400 Watt, CHIEFTEC APS-400S, 80 Plus 1x Network card PCI Intel PRO/1000GT 10/100/1000 MBit 1x Mainboard Socket-AM3 ASUS M4A79XTD EVO, ATX lshw: description: Desktop Computer product: System Product Name vendor: System manufacturer version: System Version serial: System Serial Number width: 64 bits capabilities: smbios-2.5 dmi-2.5 vsyscall64 vsyscall32 configuration: boot=normal chassis=desktop uuid=80E4001E-8C00-002C-AA59-E0CB4EBAC29A *-core description: Motherboard product: M4A79XTD EVO vendor: ASUSTeK Computer INC. physical id: 0 version: Rev X.0X serial: MT709CK11101196 slot: To Be Filled By O.E.M. *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: 0704 (11/25/2009) size: 64KiB capacity: 960KiB capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification *-cpu description: CPU product: AMD Phenom(tm) II X4 965 Processor vendor: Advanced Micro Devices [AMD] physical id: 4 bus info: cpu@0 version: AMD Phenom(tm) II X4 965 Processor serial: To Be Filled By O.E.M. slot: AM3 size: 800MHz capacity: 3400MHz width: 64 bits clock: 200MHz capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp x86-64 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save cpufreq *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 512KiB capacity: 512KiB capabilities: pipeline-burst internal varies data *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 2MiB capacity: 2MiB capabilities: pipeline-burst internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: pipeline-burst internal varies unified *-memory description: System Memory physical id: 36 slot: System board or motherboard size: 2GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber00 vendor: Manufacturer00 physical id: 0 serial: SerNum00 slot: DIMM0 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber01 vendor: Manufacturer01 physical id: 1 serial: SerNum01 slot: DIMM1 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: DIMM [empty] product: ModulePartNumber02 vendor: Manufacturer02 physical id: 2 serial: SerNum02 slot: DIMM2 *-bank:3 description: DIMM [empty] product: ModulePartNumber03 vendor: Manufacturer03 physical id: 3 serial: SerNum03 slot: DIMM3 *-pci:0 description: Host bridge product: RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part vendor: ATI Technologies Inc physical id: 100 bus info: pci@0000:00:00.0 version: 00 width: 32 bits clock: 66MHz *-pci:0 description: PCI bridge product: RD790 PCI to PCI bridge (external gfx0 port A) vendor: ATI Technologies Inc physical id: 2 bus info: pci@0000:00:02.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:a000(size=4096) memory:f8000000-fbbfffff ioport:d0000000(size=268435456) *-display description: VGA compatible controller product: G92 [GeForce GTS 250] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:ac00(size=128) memory:fbbe0000-fbbfffff *-pci:1 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port C) vendor: ATI Technologies Inc physical id: 6 bus info: pci@0000:00:06.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:b000(size=4096) memory:fbc00000-fbcfffff ioport:f6f00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: e0:cb:4e:ba:c2:9a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:45 ioport:b800(size=256) memory:f6fff000-f6ffffff memory:f6ff8000-f6ffbfff memory:fbcf0000-fbcfffff *-pci:2 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port D) vendor: ATI Technologies Inc physical id: 7 bus info: pci@0000:00:07.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:c000(size=4096) memory:fbd00000-fbdfffff *-firewire description: FireWire (IEEE 1394) product: VT6315 Series Firewire Controller vendor: VIA Technologies, Inc. physical id: 0 bus info: pci@0000:03:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress ohci bus_master cap_list configuration: driver=firewire_ohci latency=0 resources: irq:19 memory:fbdff800-fbdfffff ioport:c800(size=256) *-pci:3 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port E) vendor: ATI Technologies Inc physical id: 9 bus info: pci@0000:00:09.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:d000(size=4096) memory:fbe00000-fbefffff *-ide description: IDE interface product: 88SE6121 SATA II Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:04:00.0 version: b2 width: 32 bits clock: 33MHz capabilities: ide pm msi pciexpress bus_master cap_list configuration: driver=pata_marvell latency=0 resources: irq:17 ioport:dc00(size=8) ioport:d880(size=4) ioport:d800(size=8) ioport:d480(size=4) ioport:d400(size=16) memory:fbeffc00-fbefffff *-storage description: SATA controller product: SB700/SB800 SATA Controller [IDE mode] vendor: ATI Technologies Inc physical id: 11 bus info: pci@0000:00:11.0 logical name: scsi0 logical name: scsi2 version: 00 width: 32 bits clock: 66MHz capabilities: storage msi ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=64 resources: irq:44 ioport:9000(size=8) ioport:8000(size=4) ioport:7000(size=8) ioport:6000(size=4) ioport:5000(size=16) memory:f7fffc00-f7ffffff *-disk:0 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: CC38 serial: 9VP3WD9Z size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@0:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@0:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-disk:1 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/sdb version: CC38 serial: 9VP3SCPF size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@2:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@2:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@2:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@2:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-usb:0 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 12 bus info: pci@0000:00:12.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffd000-f7ffdfff *-usb:1 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 12.1 bus info: pci@0000:00:12.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffe000-f7ffefff *-usb:2 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 12.2 bus info: pci@0000:00:12.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:17 memory:f7fff800-f7fff8ff *-usb:3 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 13 bus info: pci@0000:00:13.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffb000-f7ffbfff *-usb:4 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 13.1 bus info: pci@0000:00:13.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffc000-f7ffcfff *-usb:5 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 13.2 bus info: pci@0000:00:13.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:19 memory:f7fff400-f7fff4ff *-serial UNCLAIMED description: SMBus product: SBx00 SMBus Controller vendor: ATI Technologies Inc physical id: 14 bus info: pci@0000:00:14.0 version: 3c width: 32 bits clock: 66MHz capabilities: ht cap_list configuration: latency=0 *-ide description: IDE interface product: SB700/SB800 IDE Controller vendor: ATI Technologies Inc physical id: 14.1 bus info: pci@0000:00:14.1 logical name: scsi5 version: 00 width: 32 bits clock: 66MHz capabilities: ide msi bus_master cap_list emulated configuration: driver=pata_atiixp latency=64 resources: irq:16 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:ff00(size=16) *-cdrom:0 description: DVD reader product: DVDROM DH16NS30 vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom1 logical name: /dev/dvd1 logical name: /dev/scd0 logical name: /dev/sr0 version: 1.00 capabilities: removable audio dvd configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 0.1.0 bus info: scsi@5:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-multimedia description: Audio device product: SBx00 Azalia (Intel HDA) vendor: ATI Technologies Inc physical id: 14.2 bus info: pci@0000:00:14.2 version: 00 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=HDA Intel latency=64 resources: irq:16 memory:f7ff4000-f7ff7fff *-isa description: ISA bridge product: SB700/SB800 LPC host controller vendor: ATI Technologies Inc physical id: 14.3 bus info: pci@0000:00:14.3 version: 00 width: 32 bits clock: 66MHz capabilities: isa bus_master configuration: latency=0 *-pci:4 description: PCI bridge product: SBx00 PCI to PCI Bridge vendor: ATI Technologies Inc physical id: 14.4 bus info: pci@0000:00:14.4 version: 00 width: 32 bits clock: 66MHz capabilities: pci subtractive_decode bus_master resources: ioport:e000(size=4096) memory:fbf00000-fbffffff *-network description: Ethernet interface product: 82541PI Gigabit Ethernet Controller vendor: Intel Corporation physical id: 5 bus info: pci@0000:05:05.0 logical name: eth1 version: 05 serial: 00:1b:21:56:f3:60 size: 100MB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k6-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=64 link=yes mingnt=255 multicast=yes port=twisted pair speed=100MB/s resources: irq:20 memory:fbfe0000-fbffffff memory:fbfc0000-fbfdffff ioport:ec00(size=64) memory:fbfa0000-fbfbffff *-usb:6 description: USB Controller product: SB700/SB800 USB OHCI2 Controller vendor: ATI Technologies Inc physical id: 14.5 bus info: pci@0000:00:14.5 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffa000-f7ffafff *-pci:1 description: Host bridge product: Family 10h Processor HyperTransport Configuration vendor: Advanced Micro Devices [AMD] physical id: 101 bus info: pci@0000:00:18.0 version: 00 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: Family 10h Processor Address Map vendor: Advanced Micro Devices [AMD] physical id: 102 bus info: pci@0000:00:18.1 version: 00 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: Family 10h Processor DRAM Controller vendor: Advanced Micro Devices [AMD] physical id: 103 bus info: pci@0000:00:18.2 version: 00 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: Family 10h Processor Miscellaneous Control vendor: Advanced Micro Devices [AMD] physical id: 104 bus info: pci@0000:00:18.3 version: 00 width: 32 bits clock: 33MHz configuration: driver=k10temp resources: irq:0 *-pci:5 description: Host bridge product: Family 10h Processor Link Control vendor: Advanced Micro Devices [AMD] physical id: 105 bus info: pci@0000:00:18.4 version: 00 width: 32 bits clock: 33MHz *-scsi physical id: 1 bus info: usb@2:3 logical name: scsi8 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk:0 description: SCSI Disk physical id: 0.0.0 bus info: scsi@8:0.0.0 logical name: /dev/sdc *-disk:1 description: SCSI Disk physical id: 0.0.1 bus info: scsi@8:0.0.1 logical name: /dev/sdd *-disk:2 description: SCSI Disk physical id: 0.0.2 bus info: scsi@8:0.0.2 logical name: /dev/sde *-disk:3 description: SCSI Disk physical id: 0.0.3 bus info: scsi@8:0.0.3 logical name: /dev/sdf *-network DISABLED description: Ethernet interface physical id: 1 logical name: vboxnet0 serial: 0a:00:27:00:00:00 capabilities: ethernet physical configuration: broadcast=yes multicast=yes

  Read the article

• How do I make my USB Bluetooth dongle work in Ubuntu 11.04 ? (Can't init device hci0: Connection timed out (110)) [closed]

  - by MaikoID

  I've a USB bluetooth dongle root@maiko-cce-lin:~# lsusb | grep Bluetooth Bus 001 Device 007: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) that isn't working properly, hardly-ever it works but stops working in my next reboot. what I've tried it isn't software blocked root@maiko-cce-lin:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hci0: Bluetooth Soft blocked: no Hard blocked: no my device is recognized by hciconfig root@maiko-cce-lin:~# hciconfig -a hci0: Type: BR/EDR Bus: USB BD Address: 00:1F:81:00:01:1C ACL MTU: 1021:4 SCO MTU: 180:1 DOWN RX bytes:330 acl:0 sco:0 events:8 errors:0 TX bytes:24 acl:0 sco:0 commands:30 errors:22 Features: 0xff 0x3e 0x09 0x76 0x80 0x01 0x00 0x80 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: Link mode: SLAVE ACCEPT but I can't turn on my hci interface root@maiko-cce-lin:~# hciconfig hci up Can't init device hci0: Connection timed out (110) I don't understand why.. the hcitool command doesn't show any device. root@maiko-cce-lin:~# hcitool dev Devices: I've tried to restart my bluetooth service too with this command and make all these previous commands again but without success. root@maiko-cce-lin:~# service bluetooth restart * Stopping bluetooth [ OK ] * Starting bluetooth [ OK ] root@maiko-cce-lin:~# The dongle works if you disconnect it from usb, wait a few seconds and connect it again. so there must be better solution for it ( a solution not involving physically removing the dongle!)

  Read the article

• pushd - handling multiple drives from cmd

  - by user673600

  I'm trying to figure out how to install some programs where the components reside on two different drives on a networked path. However whenever I use pushd \\xyz\c$ I get a mapped drive which means I cannot use any knowledge of using for example c:\install e:\mycomponents.dll. Is there anyway that I can do this once I have used the pushd command? How can I ensure that I keep the drives the same for example. I'm in the process of installing services. So it seems that when I install the service, I need to keep the path as the same as the actual location of the .exe which means that I'm running into issues. Is there a way to simply use pushd but at the sametime not actually map drives? As when installing services, when I've been using net use, I've found that there is an issue with installing on drives which are mapped, as the service whilst can be installed doesn't find the actual .exe when it comes to starting up the service. So to expand this, is there a way to solve this using net use or pushd or a combination that lets me install a service as such: c:\windows\..\installutil e:\mynode? So to clarify, I need to somehow be able to see both drives on the remote machine by their relative drives i.e. E:\ and C:\ - if I use a mapped drive letter then it means installing service is a pain because I cannot use the path.

  Read the article

• Google Doclist API : bug in revision history?

  - by Jerbome

  I'm trying to manage revisions of files (not documents) stored in google docs programatically using gdata document list java library v3. I can create files and revisions using this tool : I can see them in the web UI. The thing is : the content of my revisions seems wrong. Here is my test protocol : I create a plain text file with "Hello World" in it. I upload it to gdocs without converting it. I create a revision of this file, its content changing to "Content of the second version" I create another revision, its content is now "Content of the third version" At each step, I check the content of each revision, using my app AND using the web UI. Here is what I get : First step : no problem i see one version containing the "Hello world" text Second step : no problem either, i see 2 versions, containing Hello World for the first one and Content of the second version for the second. Third step : here the problems comes. I see my 3 versions, but only the third and last seems to be correct. when i download the second version, the content is "Content of the second versio" (not a typo, it misses the 'n'). And i cannot even download the initial version, it seems to timeout. Important thing : I did not have this problem three weeks ago, my revision management worked well. I have no idea of what happens there, except it seems to be server-related, as the problem is seen either with my app or the google native webapp. Last thing : I tried using the google drive API as gdocs had been merged with drive. When i request revisions of my file, the API returns me an error saying that revisions are not supported for files, even if i can see them in the UI. I tried on converted documents, it worked. I'm looking for a workaround for this problem. Has anyone ever encountered such a problem ? Thanks in advance, Jérôme

  Read the article

• Windows 7 Backup - Does the "system image" include all the files on my drive?

  - by Vaccano

  I have a new Dell Laptop that I have setup the way I like it. I want to use Windows 7 to do a backup and then restore that backup on a different hard drive (solid state). When I setup the backup info (manually) for Windows 7 Backup there is a little checkbox at the the bottom that says: Include a system image of drives: RECOVERY, OS (C:) I can also select to backup all my data on the C: drive (the only hard drive I have anything on) as well as some libraries (which are on my C: drive so no point in selecting those). The question I have is, does Windows 7 Backup just somehow know what needs to be restored (ie program files and Windows and the registry ....? Or is it really making a full restorable copy of the C: drive? (If the later is true then I don't need select the C: drive to be "backed up" if I don't plan to access the files except by restoring them right? (Because the system image will already have it all.)) So, which way is it? What is saved in the System Image?

  Read the article

• How can I allow the Xbox 360 to browse movies on a network drive?

  - by Roger

  I've always been able to stream movies stored on my Windows 7 computer's local hard drive to the Xbox 360 with no problems. A few weeks ago, though, I got a Seagate Dockstar NAS device and moved my movies to it. Ever since then, I can't seem them in the Xbox. I've tried several different things. When I try to add the mapped drive to the Media Player library, it says that it can't share the files. (I don't have any security on the NAS drive). I've tried creating a symlink to a local drive, but that doesn't help. Neither does adding the UNC path directly. The Dockstar seems to have its own Xbox share capability, but it doesn't respect my folder structure - it brings over every video file on the drive in a single list, including several hundred home videos that aren't playable on the Xbox. Is there any way to use Media Player (or the Zune software) to share files stored on a NAS drive? Barring this, is there a lightweight, free server that will allow me to share these files while maintaining my folder structure?

  Read the article

• CMD/ADB - Autorun script to search, copy, and paste a file from android system to flash drive

  - by Outride

  I've looked around and can't find anything that answers my question. This is my first question, so any tips or thoughts are welcome, as well as an answer :p As explained in title, i want to create a script that launches, finds a file on android phone, copies it, and pastes it to a flash drive. As of right now, it's a mix of multiple tutorials, trial and error, and I'm at a point of giving up. As of right now, I have a flash drive, loaded with three scripts. As follows: Bold = name of file file.bat @echo off :: variables /min SET odrive=%odrive:~0,2% set backupcmd=xcopy /s /c /d /e /h /i /r /y echo off %backupcmd% "C:\Users\Outride\Desktop\kikDatabase.db" "%drive%\all" @echo off cls invisible.vbs CreateObject("Wscript.Shell").Run """" & WScript.Arguments(0) & """", 0, False launch.bat wscript.exe \invisible.vbs file.bat So far, I had to use android commander, manually go through the directory, find /data/data/kik.android/databases and then copy kikDatabase.db to my desktop. Then run this scrip. Yes i'm trying to pull the database to copy all my email contacts. I use launch.bat, which then makes file.bat invisible due to the invisible.vbs script. What would i need to do now to have the file searched for and copied to the flashdrive? Thanks in advance, i'll be glad to answer any questions if theres any :p just remember that i'm not exactly a tech expert haha EDIT* Cleared junk of prior edits. New - I now have a .bat script to recognize what drive the usb is on, and launch py_cmd (adb shell) This is the current script. pull.bat @echo off :: variables SET odrive=%odrive:~0,2% set launching=start "%drive%\Minimal ADB and Fastboot\py_cmd" echo off %launching% so how could I make it for the .bat or a new script, to type the following "adb pull /data/data/kik.android/databases/ %drive%\All\Database" into the adb terminal? please help! I've been racking my brain over this all night :3

  Read the article

• How to back up initial state of external backup drive?

  - by intuited

  I've picked up an HP Simplesave external drive. It comes with some fancy software that is of no use to me because I don't use Windows. Like many current consumer-targeted backup drives, the backup software is actually contained on the drive itself. I'd like to save the drive's initial state so that I can restore it if I decide to sell it. The backup box itself is somewhat customized: in addition to the hard drive device, it presents a CDROM-like device on /dev/sr0. I gather that the purpose of this cdrom device is to bootstrap via Windows autoplay the backup application which lives on the disk itself. I wouldn't suppose any guarantees about how it does this, so it seems important to preserve the exact state of the disk. The drive is formatted with a single 500GB NTFS partition. My initial thought was to use dd to dump the disk (/dev/sdb) itself, but this proved impractical, as the resulting file was not sparse. This seemed to be because the NTFS empty space is not filled with zeroes, but with a repeating series of 16 bytes. I tried gzipping the output of dd. This reduced to the file to a manageable size — the first 18GB was compressed to 81MB, versus 47MB to tarball the contents of the mounted filesystem — but it was very slow on my admittedly somewhat derelict Pentium M processor. The time to do that first 18GB was about 30 minutes. So I've resorted to dumping the disk state and partition data separately. I've dumped the partition state with sfdisk -d /dev/sdb > sfdisk.-d.out I've also created a compressed image of the NTFS partition (the only one on the disk) with ntfsclone --save-image --output - /dev/sdb1 | gzip -c > ntfsclone.img.gz Is there anything else I should do to ensure that I can restore the precise original state of the drive?

  Read the article

• Searching for SD-cards

  - by Shaddix

  I need to implement searching for SD-cards in my program. Currently I'm using search for all removable devices like: searcher = New Management.ManagementObjectSearcher("\\localhost\root\cimv2", "SELECT DeviceId FROM Win32_LogicalDisk WHERE DriveType=2 AND Size>0"); But it find USB flash drives also. Is there a proper way to find SD-cards only? What I need is in general only drive letter for available SD-cards (like "F:" or so).

  Read the article

• How to get a file path from c drive in android

  - by Thomas Mathew

  I was trying to extract the content of a pdf file and display its content in android. I tired the code in java and it worked.But when i am coding it in android, its not displaying anything. I think, its not getting the file path. Is there any way by which i could get a file stored in c drive and store its path in a string? The code is given below: public class hello extends Activity { /** Called when the activity is first created. */ private static String INPUTFILE = "FirstPdf.pdf"; String str; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); try { Document document = new Document(); document.open(); PdfReader reader = new PdfReader(INPUTFILE); int n = reader.getNumberOfPages(); str=PdfTextExtractor.getTextFromPage(reader, 2); } catch (IOException e) { //e.printStackTrace(); } catch (InterruptedException e) { e.printStackTrace(); } TextView tv = new TextView(this); tv.setText(str); setContentView(tv); } } I would be very grateful if the problem is solved.

  Read the article

• Generating all unique combinations for "drive ya nuts" puzzle

  - by Yuval A

  A while back I wrote a simple python program to brute-force the single solution for the drive ya nuts puzzle. The puzzle consists of 7 hexagons with the numbers 1-6 on them, and all pieces must be aligned so that each number is adjacent to the same number on the next piece. The puzzle has ~1.4G non-unique possibilities: you have 7! options to sort the pieces by order (for example, center=0, top=1, continuing in clockwise order...). After you sorted the pieces, you can rotate each piece in 6 ways (each piece is a hexagon), so you get 6**7 possible rotations for a given permutation of the 7 pieces. Totalling: 7!*(6**7)=~1.4G possibilities. The following python code generates these possible solutions: def rotations(p): for i in range(len(p)): yield p[i:] + p[:i] def permutations(l): if len(l)<=1: yield l else: for perm in permutations(l[1:]): for i in range(len(perm)+1): yield perm[:i] + l[0:1] + perm[i:] def constructs(l): for p in permutations(l): for c in product(*(rotations(x) for x in p)): yield c However, note that the puzzle has only ~0.2G unique possible solutions, as you must divide the total number of possibilities by 6 since each possible solution is equivalent to 5 other solutions (simply rotate the entire puzzle by 1/6 a turn). Is there a better way to generate only the unique possibilities for this puzzle?

  Read the article

• Trusted Folder/Drive Picker in the Browser

  - by kylepfritz

  I'd like to write a Folder/Drive picker the runs in the browser and allows a user to select files to upload to a webservice. The primary usage would be selecting folders or a whole CD and uploading them to the web with their directory structure in tact. I'm imagining something akin to Jumploader but which automatically enumerates external drives and CDs. I remember a version of Facebook's picture uploader that could do this sort of enumeration and was java-based but it has since been replaced by a much slicker plugin-based architecture. Because the application needs to run at very high trust, I think I'm limited to old-school java applets. Is there another alternative? I'm hesitant to start down the plugin route because of the necessity of writing one for both IE and Mozilla at a minimum. Are there good places to get started there? On the applet front, I built a clunky prototype to demonstrate that I can enumerate devices and list files. It runs fine in the applet viewer but I don't think I have the security settings configured correctly for it to run in the browser at full trust. Currently I don't get any drives back when I run it in the browser. Applet Prototype: public class Loader extends javax.swing.JApplet { ... private void EnumerateDrives(java.awt.event.ActionEvent evt) { File[] roots = File.listRoots(); StringBuilder b = new StringBuilder(); for (File root : roots) { b.append(root.getAbsolutePath() + ", "); } jLabel.setText(b.toString()); } } Embed Html: <p>Loader:</p> <script src="http://www.java.com/js/deployJava.js" type="text/javascript" ></script> <script> var attributes = {code:'org.exampl.Loader.Loader.class', archive:'Loader/dist/Loader.jar', width:600, height:400} ; var parameters = {}; deployJava.runApplet(attributes, parameters, '1.6');

  Read the article

• How can I write an XML on my hard drive to GetRequestStream

  - by swolff1978

  I need to post raw xml to a site and read the response. With the following code I keep getting an "Unknown File Format" error and I'm not sure why. XmlDocument sampleRequest = new XmlDocument(); sampleRequest.Load(@"C:\SampleRequest.xml"); byte[] bytes = Encoding.UTF8.GetBytes(sampleRequest.ToString()); string uri = "https://www.sample-gateway.com/gw.aspx"; req = WebRequest.Create(uri); req.Method = "POST"; req.ContentLength = bytes.Length; req.ContentType = "text/xml"; using (var requestStream = req.GetRequestStream()) { requestStream.Write(bytes, 0, bytes.Length); } // Send the data to the webserver rsp = req.GetResponse(); XmlDocument responseXML = new XmlDocument(); using (var responseStream = rsp.GetResponseStream()) { responseXML.Load(responseStream); } I am fairly certain my issue is what/how I am writing to the requestStream so.. How can I modify that code so that I may write an xml located on the hard drive to the request stream?

  Read the article

• Hard Drive POV clock

  - by SkinnyMAN

  I am building a hard drive POV clock. (google it, they are pretty cool) I am working on the code for it, right now all i want to do is get the hang of making it do simple patterns with the RGB leds. I am wondering if anyone has any ideas on how to do something simple like make a red line rotate around the platter. right now what i have is an interrupt that triggers a function. int gLED = 8; // pins for RGB led strip int rLED = 9; int bLED = 10; attachInterrupt(0, ledPattern, FALLING); void ledPattern(){ digitalWrite(gLED, HIGH); // This will make a stable image of slice of the delayMicroseconds(500); // platter, but it does not move. digitalWrite(gLED, LOW); } That is the main part of the code (obviously I cut some stuff out that arduino requires) What I am trying to figure out is how can make that slice rotate around the platter. Eventually I will make the pattern more interesting by adding in other colors. Any Ideas?

  Read the article

• Spikes of 99% disk activity in Windows 8 Task Manager

  - by Jonathan Chan

  For some reason Windows 8's Task Manager reports spikes of 99% disk activity for hours at a time. Looking at the entries in that column, however, data doesn't seem to be getting written any more quickly than when the disk activity is around 25-50% (which it seem to idle at most of the time). Furthermore, when these 99% disk activity spikes are happening, the average response time reported in the Performance tab becomes 4000-6000ms. Is there a good way to find out what is causing the disk activity? I've tried using Process Explorer, but I said above, the rate at which data is reportedly being written doesn't seem to correspond (Dropbox and Google Chrome are constantly the top two, but the spikes are not dependent on their being open). Thanks in advance for any help. It gets very annoying when the computer stutters to a halt.

  Read the article

• Daemon Tools Lite Error- Unable to add adapter

  - by Lirik

  I just got a ThinkPad T510 with Windows 7 Professional and I installed Daemon Tools Lite, but I keep getting an error when I run it: Unable to add adapter. I tried starting it as an administrator, but I got the same problem. Does anybody know how to fix this?

  Read the article

• Hard disk with bad clusters

  - by Dan

  I have been trying to backup some files up to DVD recently, and the burn process failed saying the CRC check failed for certain files. I then tried to browse to these files in Windows explorer and my whole machine locks up and I have to reboot. I ran check disk without the '/F /R' arguments and it told me I had bad sectors. So I re-ran it with the arguments and check disk fails during the 'Chkdsk is verifying usn journal' stage with this error: Insufficient disk space to fix the usn journal $j data stream The hard disk is a 300GB Partition on a 400GB Disk, and there is 160GBs of free space on the partition. My os (Windows 7) is installed on the other partition and is running fine. Any idea how I fix this? or repair it enough to copy my files off it?

  Read the article

• Ubuntu doesn't detect drives conected to LSI "Host Bus Adapter"

  - by dvrecmfo

  I purchased LSI SAS 9300-4i Host Bus Adapter, from card bios I can see that it detected all hard drives connected to it, but from ubuntu I can't see them. What I've tried: Installed the driver provided here http://www.lsi.com/products/host-bus-adapters/pages/lsi-sas-9300-4i.aspx#tab/tab3 (I tried both LINUX_RH_SL_OEL_CTX_MPT_GEN3_C0_Phase2.0-3.00.00.00-1 and Linux_Driver_RHEL5-6_SLES10-11_P1) lspci | grep -i lsi 07:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS3004 PCI-Express Fusion-MPT SAS-3 (rev 02)

  Read the article

• What free space thresholds/limits are advisable for 640 GB and 2 TB hard disk drives with ZEVO ZFS on OS X?

  - by Graham Perrin

  Assuming that free space advice for ZEVO will not differ from advice for other modern implementations of ZFS … Question Please, what percentages or amounts of free space are advisable for hard disk drives of the following sizes? 640 GB 2 TB Thoughts A standard answer for modern implementations of ZFS might be "no more than 96 percent full". However if apply that to (say) a single-disk 640 GB dataset where some of the files most commonly used (by VirtualBox) are larger than 15 GB each, then I guess that blocks for those files will become sub optimally spread across the platters with around 26 GB free. I read that in most cases, fragmentation and defragmentation should not be a concern with ZFS. Sill, I like the mental picture of most fragments of a large .vdi in reasonably close proximity to each other. (Do features of ZFS make that wish for proximity too old-fashioned?) Side note: there might arise the question of how to optimise performance after a threshold is 'broken'. If it arises, I'll keep it separate. Background On a 640 GB StoreJet Transcend (product ID 0x2329) in the past I probably went beyond an advisable threshold. Currently the largest file is around 17 GB –  – and I doubt that any .vdi or other file on this disk will grow beyond 40 GB. (Ignore the purple masses, those are bundles of 8 MB band files.) Without HFS Plus: the thresholds of twenty, ten and five percent that I associate with Mobile Time Machine file system need not apply. I currently use ZEVO Community Edition 1.1.1 with Mountain Lion, OS X 10.8.2, but I'd like answers to be not too version-specific. References, chronological order ZFS Block Allocation (Jeff Bonwick's Blog) (2006-11-04) Space Maps (Jeff Bonwick's Blog) (2007-09-13) Doubling Exchange Performance (Bizarre ! Vous avez dit Bizarre ?) (2010-03-11) … So to solve this problem, what went in 2010/Q1 software release is multifold. The most important thing is: we increased the threshold at which we switched from 'first fit' (go fast) to 'best fit' (pack tight) from 70% full to 96% full. With TB drives, each slab is at least 5GB and 4% is still 200MB plenty of space and no need to do anything radical before that. This gave us the biggest bang. Second, instead of trying to reuse the same primary slabs until it failed an allocation we decided to stop giving the primary slab this preferential threatment as soon as the biggest allocation that could be satisfied by a slab was down to 128K (metaslab_df_alloc_threshold). At that point we were ready to switch to another slab that had more free space. We also decided to reduce the SMO bonus. Before, a slab that was 50% empty was preferred over slabs that had never been used. In order to foster more write aggregation, we reduced the threshold to 33% empty. This means that a random write workload now spread to more slabs where each one will have larger amount of free space leading to more write aggregation. Finally we also saw that slab loading was contributing to lower performance and implemented a slab prefetch mechanism to reduce down time associated with that operation. The conjunction of all these changes lead to 50% improved OLTP and 70% reduced variability from run to run … OLTP Improvements in Sun Storage 7000 2010.Q1 (Performance Profiles) (2010-03-11) Alasdair on Everything » ZFS runs really slowly when free disk usage goes above 80% (2010-07-18) where commentary includes: … OpenSolaris has changed this in onnv revision 11146 … [CFT] Improved ZFS metaslab code (faster write speed) (2010-08-22)

  Read the article

• Use hard disk image like a regular hard disk on Linux

  - by jobnoorman

  If you have a hard disk image (including partition table, multiple partitions,...), is it possible to let Linux treat it as a regular hard disk? By "regular hard disk" I mean I would like to have the image show up as, for instance, /dev/hdx and its partitions as /dev/hdx1,... (I know I can mount one of the partitions in the image using "mount -o loop,offset=x ..." but I don't really like this option.)

  Read the article

• Disk is spinning down each minute, unable to disable it

  - by lzap

  I played with spindown and APM settings of my Samsung discs and now they spin down every minute. I want to disable it, but it seems it does not accept any of the spindown time or APM values. Nothing works, it's all the same. Please help what values should be proper for it. I do not want it to spin down at all. /dev/sda: ATA device, with non-removable media Model Number: SAMSUNG HD154UI Serial Number: S1Y6J1KZ206527 Firmware Revision: 1AG01118 Standards: Used: ATA-8-ACS revision 3b Supported: 7 6 5 4 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 2930277168 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 1430799 MBytes device size with M = 1000*1000: 1500301 MBytes (1500 GB) cache/buffer size = unknown Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 udma7 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test Media Card Pass-Through * General Purpose Logging feature set * 64-bit World wide name * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * NCQ priority information DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Long Sector Access (AC1) * SCT LBA Segment Access (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 326min for SECURITY ERASE UNIT. 326min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 50024e900300cca3 NAA : 5 IEEE OUI : 0024e9 Unique ID : 00300cca3 Checksum: correct I have the very same disc which I did not "tuned" and it does not spin. But I do not know where to read the settings from. The hdparm only shows this: Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 Edit: It seems the issue was tuned daemon in RHEL6. It was too aggressive, I turned off disc tuning and it seems they are no longer spinning down.

  Read the article

• replace laptop hard disk

  - by 5YrsLaterDBA

  I have bought a ACER Aspire 5736Z-4790 laptop for my parents. It just passed the warranty. I think the hard disk is bad now. I cannot open/copy some of my files. It will crash (blue screen) when I do chkdsk /f/r in the stage 4 of 5 which is verifying file data. I can hear a strange noise when it is reading the bad sectors (I guess because it hangs there.) I am thinking replace the hard disk. should I buy the same hard disk or any SATA laptop hard disk will be ok? BTW, is there a way to repair it (with software)?

  Read the article

< Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >