Search Results

Search found 5398 results on 216 pages for 'xorg conf'.

Page 185/216 | < Previous Page | 181 182 183 184 185 186 187 188 189 190 191 192  | Next Page >

• Motion - takes snapshot without motion detected

  - by Emmanuel Brunet

  I've been installed the standard motion 3.2.12 package on debian 7.5. I would like to get snapshot ONLY when motion is detected, but it still saves a picture every second without any activity in front of the camera. I'm using a TENVIS JPT3815W IP camera motion.conf here is my configuration file setup_mode off target_dir /media/videos/log/webcam netcam_url http://webcam/snapshot.cgi netcam_tolerant_check on netcam_userpass admin:alpha1237 # Output frames at 1 fps when no motion is detected and increase to the # rate given by webcam_maxrate when motion is detected (default: off) webcam_motion off output_all off # detection settings 1-255 default 32 noise_level 50 # Maximum framerate for webcam streams (default: 1) webcam_maxrate 25 pre_capture 0 framerate 25 gap 30 locate on mail [email protected] text_right "FRONT CAMERA %Y/%m/%d - %T" text_double on ffmpeg_cap_new on ffmpeg_cap_motion on ffmpeg_video_codec mpeg4 output_motion off snapshot_interval 0 # Quality of the jpeg (in percent) images produced (default: 50) quality 90 # Restrict webcam connections to localhost only (default: on) webcam_localhost off # Limits the number of images per connection (default: 0 = unlimited) # Number can be defined by multiplying actual webcam rate by desired number of seconds # Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate webcam_limit 0 Issue when I start motion images are stored in /media/videos/log/webcam nearly every second. I hjust want to get images when a motion is detected and the according video clip Any idea where the configuration fails ?

  Read the article

• Installing chrome in Centos 6.2 (Final)

  - by usjes

  I need to install chrome in a dedicated centos server where I only access via ssh, it doesn't have X or any windows graphical stuff. I need it to be able to pack extensions using google-chrome --pack-extension. I tried adding this to /etc/yum.repos.d/google.repo [google-chrome] name=google-chrome - 32-bit baseurl=http://dl.google.com/linux/chrome/rpm/stable/i386 enabled=1 gpgcheck=1 gpgkey=https://dl-ssl.google.com/linux/linux_signing_key.pub And then yum install google-chrome-stable, but there's a huge list of dependencies problems: How can I install chrome without breaking anything else? UPDATE: Ok, I installed perl-CGI from .rpm because yum couldn't find it, now dependencies resolve and it show me this list of packages to install: Dependencies Resolved ============================================================================================================================================================================================================================================= Package Arch Version Repository Size ============================================================================================================================================================================================================================================= Installing: google-chrome-stable x86_64 19.0.1084.52-138391 google-chrome 35 M Installing for dependencies: ConsoleKit x86_64 0.4.1-3.el6 base 82 k ConsoleKit-libs x86_64 0.4.1-3.el6 base 17 k GConf2 x86_64 2.28.0-6.el6 base 964 k ORBit2 x86_64 2.14.17-3.1.el6 base 168 k bc x86_64 1.06.95-1.el6 base 110 k cdparanoia-libs x86_64 10.2-5.1.el6 base 47 k cups x86_64 1:1.4.2-44.el6_2.3 updates 2.3 M dbus x86_64 1:1.2.24-5.el6_1 base 207 k desktop-file-utils x86_64 0.15-9.el6 base 47 k ed x86_64 1.1-3.3.el6 base 72 k eggdbus x86_64 0.6-3.el6 base 91 k foomatic x86_64 4.0.4-1.el6_1.1 base 251 k foomatic-db noarch 4.0-7.20091126.el6 base 980 k foomatic-db-filesystem noarch 4.0-7.20091126.el6 base 4.4 k foomatic-db-ppds noarch 4.0-7.20091126.el6 base 19 M ghostscript x86_64 8.70-11.el6_2.6 updates 4.4 M ghostscript-fonts noarch 5.50-23.1.el6 base 751 k gstreamer x86_64 0.10.29-1.el6 base 764 k gstreamer-plugins-base x86_64 0.10.29-1.el6 base 942 k gstreamer-tools x86_64 0.10.29-1.el6 base 23 k iso-codes noarch 3.16-2.el6 base 2.4 M lcms-libs x86_64 1.19-1.el6 base 100 k libIDL x86_64 0.8.13-2.1.el6 base 83 k libXScrnSaver x86_64 1.2.0-1.el6 base 19 k libXfont x86_64 1.4.1-2.el6_1 base 128 k libXv x86_64 1.0.5-1.el6 base 21 k libfontenc x86_64 1.0.5-2.el6 base 24 k libgudev1 x86_64 147-2.40.el6 base 59 k libmng x86_64 1.0.10-4.1.el6 base 165 k libogg x86_64 2:1.1.4-2.1.el6 base 21 k liboil x86_64 0.3.16-4.1.el6 base 121 k libtheora x86_64 1:1.1.0-2.el6 base 129 k libvisual x86_64 0.4.0-9.1.el6 base 135 k libvorbis x86_64 1:1.2.3-4.el6_2.1 updates 168 k mailx x86_64 12.4-6.el6 base 234 k man x86_64 1.6f-29.el6 base 263 k mesa-libGLU x86_64 7.11-3.el6 base 201 k nvidia-graphics195.30-libs x86_64 195.30-120.el6 atrpms 13 M openjpeg-libs x86_64 1.3-7.el6 base 59 k pax x86_64 3.4-10.1.el6 base 69 k phonon-backend-gstreamer x86_64 1:4.6.2-20.el6 base 125 k polkit x86_64 0.96-2.el6_0.1 base 158 k poppler x86_64 0.12.4-3.el6_0.1 base 557 k poppler-data noarch 0.4.0-1.el6 base 2.2 M poppler-utils x86_64 0.12.4-3.el6_0.1 base 73 k portreserve x86_64 0.0.4-4.el6_1.1 base 22 k qt x86_64 1:4.6.2-20.el6 base 4.0 M qt-sqlite x86_64 1:4.6.2-20.el6 base 50 k qt-x11 x86_64 1:4.6.2-20.el6 base 12 M qt3 x86_64 3.3.8b-30.el6 base 3.5 M redhat-lsb x86_64 4.0-3.el6.centos base 24 k redhat-lsb-graphics x86_64 4.0-3.el6.centos base 12 k redhat-lsb-printing x86_64 4.0-3.el6.centos base 11 k sgml-common noarch 0.6.3-32.el6 base 43 k time x86_64 1.7-37.1.el6 base 26 k tmpwatch x86_64 2.9.16-4.el6 base 31 k xdg-utils noarch 1.0.2-17.20091016cvs.el6 base 58 k xml-common noarch 0.6.3-32.el6 base 9.5 k xorg-x11-font-utils x86_64 1:7.2-11.el6 base 75 k xz x86_64 4.999.9-0.3.beta.20091007git.el6 base 137 k xz-lzma-compat x86_64 4.999.9-0.3.beta.20091007git.el6 base 16 k Transaction Summary ============================================================================================================================================================================================================================================= Install 62 Package(s) Is it safe to continue and install all that or could I break something already installed?

  Read the article

• Turn off gzip for a location in Nginx

  - by Nyxynyx

  How can gzip be turned off for a particular location and all its sub-directories? My main site is at http://mydomain.com and I want to turn gzip off for both http://mydomain.com/foo and http://mydomain.com/foo/bar. gzip is turned on in nginx.conf. I tried turning off gzip as shown below, but the Response Headers in Chrome's dev tools shows that Content-Encoding:gzip. How should gzip/output buffering be disabled properly? Attempt: server { listen 80; server_name www.mydomain.com mydomain.com; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; root /var/www/mydomain/public; index index.php index.html; location / { gzip on; try_files $uri $uri/ /index.php?$args ; } location ~ \.php$ { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; fastcgi_read_timeout 300; } location /foo/ { gzip off; try_files $uri $uri/ /index.php?$args ; } }

  Read the article

• How to find process that's using 100% of CPU

  - by Gabriel

  As i'm looking at htop and top i see that my processor usage is 100% allways. But i can not see any process that is using that much CPU. Htop shows me only 1-2 processes that use around 5% cpu time. Is there a way to find the processes that use that much cpu time? Here is the output of ps -eo pcpu,pid,user,args | sort -r -k1 | less %CPU PID USER COMMAND 0.8 20413 root jsvc.exec -user tomcat -cp ./bootstrap.jar -Djava.endorsed.dirs=../common/endorsed -outfile ../logs/catalina.out -errfile ../logs/catalina.err -verbose org.apache.catalina.startup.Bootstrap -security 0.3 631 mysql /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --pid-file=/var/lib/mysql/mysql.pid --skip-external-locking 0.2 3380 root /usr/local/apache/bin/httpd -k restart -DSSL 0.2 24698 root tailwatchd 0.2 22472 root /usr/local/jdk/bin/java -Djava.util.logging.config.file=/usr/local/jakarta/tomcat/conf/logging.properties -Dfile.encoding=UTF8 -XX:MaxPermSize=128m -Djava.util.logging.manager=org.apache.juli.ClassLoaderLogManager -Djava.endorsed.dirs=/usr/local/jakarta/tomcat/common/endorsed -classpath /usr/local/jakarta/tomcat/bin/bootstrap.jar -Dcatalina.base=/usr/local/jakarta/tomcat -Dcatalina.home=/usr/local/jakarta/tomcat -Djava.io.tmpdir=/usr/local/jakarta/tomcat/temp org.apache.catalina.startup.Bootstrap start 0.1 32095 root cpanellogd - processing bandwidth 0.0 9733 root sleep 1m

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

• Webserver max CPU when apache and MYSQL are ran together

  - by Tim

  This website has been running fine without issues, Recently it went down. After some investigation it looks like the combo of MYSQL and Apache bring the box to its knees. Apache can run find serving static web pages and MYSQL can run fine when the website isn't working. As soon as the website is enabled with SQL running the CPU on the box remains at 100%. Picture of the usage: http://i.stack.imgur.com/GG2NC.png I've checked the sql database for errors, tried tuning nearly every parameter in apache/sql's conf file for performance. The server is a redhat based box running the latest software packages. Any help/suggestions are welcome. Doing an strace on a high cpu apache process I see the following: read(14, "", 8192) = 0 close(14) = 0 socket(PF_FILE, SOCK_STREAM, 0) = 14 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) connect(14, {sa_family=AF_FILE, path="/var/lib/mysql/mysql.sock"...}, 110) = 0 setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\2003\341\1\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "\2003\341\1\0\0\0\0", 8) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) setsockopt(14, SOL_SOCKET, SO_KEEPALIVE, [1], 4) = 0 Here is what I see from a mysql process: futex(0x86fc9a4, FUTEX_WAIT_PRIVATE, 39, NULL) = 0 futex(0x86fc734, FUTEX_WAIT_PRIVATE, 2, NULL) = 0 futex(0x86fc734, FUTEX_WAKE_PRIVATE, 1) = 0 gettimeofday({1301465020, 141613}, NULL) = 0 clock_gettime(CLOCK_REALTIME, {1301465020, 141699633}) = 0 futex(0x8707a64, FUTEX_WAIT_PRIVATE, 1, {4, 999913367}) = 0 futex(0x8707a40, FUTEX_WAIT_PRIVATE, 2, NULL) = 0 futex(0x8707a40, FUTEX_WAKE_PRIVATE, 1) = 0 exit_group(0) = ?

  Read the article

• Tripwire help Required

  - by ramaperumal

  I have created the policy file in Tripwire and also I have created the rules as well mentioned below: /opt/jboss/server/gis/conf -> $(SEC_CONFIG) +aipm +c+g+a+i+s+t+u+l+M; /usr/local/gtech/eseries/ -> $(SEC_CONFIG) +a+c+g+i+s+t+u+l+M ; After running the integrity check the output should be a(Access timestamp),c (Inode timestamp (create/modify),g (File owner's group ID),i (Inode number),s (File size),t (time stamp),u (File owner's user ID),l(File is increasing in size (a "growing file"),M (MD5 hash value). I am getting the output as below: [root@xxsi1242 tripwire]# tripwire --check Parsing policy file: /etc/tripwire/tw.pol *** Processing Unix File System *** Performing integrity check... Wrote report file: /var/lib/tripwire/report/xxsi1242.gtk.gtech.com-20131106-053812.twr Open Source Tripwire(R) 2.4.1 Integrity Check Report Report generated by: root Report created on: Wed 06 Nov 2013 05:38:12 AM EST Database last updated on: Wed 06 Nov 2013 05:31:17 AM EST =============================================================================== Report Summary: =============================================================================== Host name: xxsi1242.gtk.gtech.com Host IP address: 156.24.65.171 Host ID: None Policy file used: /etc/tripwire/tw.pol Configuration file used: /etc/tripwire/tw.cfg Database file used: /var/lib/tripwire/xxsi1242.gtk.gtech.com.twd Command line used: tripwire --check =============================================================================== Rule Summary: =============================================================================== ------------------------------------------------------------------------------- Section: Unix File System ------------------------------------------------------------------------------- Rule Name Severity Level Added Removed Modified --------- -------------- ----- ------- -------- Invariant Directories 66 0 0 0 Temporary directories 33 0 0 0 * Tripwire Data Files 100 0 0 1 Tech Stack 100 0 0 0 User binaries 66 0 0 0 Tripwire Binaries 100 0 0 0 * CLPS bins 100 0 0 2 CLPS Configuration files 100 0 0 0 ESCommon 100 0 0 0 Shell Binaries 100 0 0 0 OS executables and libraries 100 0 0 0 Security Control 100 0 0 0 ESCommon Configuration 100 0 0 0 (/etc/gtech/escommon) Total objects scanned: 12358 Total violations found: 3 =============================================================================== Object Summary: =============================================================================== ------------------------------------------------------------------------------- # Section: Unix File System ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Rule Name: Tripwire Data Files (/etc/tripwire/tw.pol) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/etc/tripwire/tw.pol" ------------------------------------------------------------------------------- Rule Name: CLPS bins (/opt/jboss/server) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/opt/jboss/server/esapps1/data/hypersonic/localDB.lck" "/opt/jboss/server/gis/data/hypersonic/localDB.lck" =============================================================================== Error Report: =============================================================================== No Errors ------------------------------------------------------------------------------- *** End of report *** Note: In the output I only am getting the files which are modified. I need the detail output for this. But unfortunately I am not getting what I expected. Please help me to proced further.

  Read the article

• Which DNS settings are used when setting up your server

  - by Saif Bechan

  I have a server and want to run my own name server service. Now I have set it up already and it works not, but I do not know where the exact settings are stored. On my server I use Plesk. When I edit DNS settings there I think it is stored in named.conf. Named is installed on the server, and BIND. Now I also have a panel from my registrar. This is separate from my server. Both places I can add the normal MX,A,CNAME, etc records. Now where is the best way to place this settings. Currently I have the same records on both places, on the server and at the registrar panel. I am correct to just add all the records at the registrar panel, and remove everything from within PLESK, and just don't run DNS on my server, because it is already done in the registrar panel. Or should I add the records in both places.

  Read the article

• mod_rpaf with apache error_log

  - by Camden S.

  I'm using mod-rpaf with Apache 2.4 and it's working properly (showing the real client IP's) in my Apache access_log... but not in my error_log. My error log just shows the client IP address of the proxy server (my load balancer in this case) Here's an example of what I see in my error_log where 123.123.123.123 is the IP of my load balancer/proxy. == /usr/local/apache2/logs/error_log <== [Tue Jun 05 20:24:31.027525 2012] [access_compat:error] [pid 9145:tid 140485731845888] [client 123.123.123.123:20396] AH01797: client denied by server configuration: /wwwroot/private/secret.pdf The exact same request produces the following in my access_log where 456.456.456.456 is a real client IP (not the IP of the load balancer). 456.456.456.456 - - [05/Jun/2012:20:24:31 +0000] "GET /wwwroot/private/secret.pdf HTTP/1.1" 403 228 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.7; rv:12.0) Gecko/20100101 Firefox/12.0" Here's my httpd.conf entry: # RPAF LoadModule rpaf_module modules/mod_rpaf-2.0.so RPAFenable On RPAFproxy_ips 127.0.0.1 123.123.123.123 RPAFsethostname On RPAFheader X-Forwarded-For What do I need to do to get the real IP addresses showing in my Apache error_log?

  Read the article

• NGINX rewrite for vanity URLs when file doesn't exist (try_files and rewrite together)

  - by user1721724

  I'm trying to get vanity URLs on my server. If the file path from the URL doesn't exist, I want to rewrite the URL to profile.php, but if my users have periods in their usernames, their vanity URL doesn't work. Here is my conf block. server { listen 80; server_name www.example.com; rewrite ^/([a-zA-Z0-9-_]+)$ /profile.php?url=$1 last; root /var/www/html/example.com; error_page 404 = /404.php; location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires 1y; log_not_found off; } location ~ \.php$ { fastcgi_pass example_fast_cgi; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/html/example.com$fastcgi_script_name; include fastcgi_params; } location / { index index.php index.html index.htm; } location ~ /\.ht { deny all; } location /404.php { internal; return 404; } } Any help would be appreciated. Thanks!

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Understanding RedHats recommended tuned profiles

  - by espenfjo

  We are going to roll out tuned (and numad) on ~1000 servers, the majority of them being VMware servers either on NetApp or 3Par storage. According to RedHats documentation we should choose the virtual-guestprofile. What it is doing can be seen here: tuned.conf We are changing the IO scheduler to NOOP as both VMware and the NetApp/3Par should do sufficient scheduling for us. However, after investigating a bit I am not sure why they are increasing vm.dirty_ratio and kernel.sched_min_granularity_ns. As far as I have understood increasing increasing vm.dirty_ratio to 40% will mean that for a server with 20GB ram, 8GB can be dirty at any given time unless vm.dirty_writeback_centisecsis hit first. And while flushing these 8GB all IO for the application will be blocked until the dirty pages are freed. Increasing the dirty_ratio would probably mean higher write performance at peaks as we now have a larger cache, but then again when the cache fills IO will be blocked for a considerably longer time (Several seconds). The other is why they are increasing the sched_min_granularity_ns. If I understand it correctly increasing this value will decrease the number of time slices per epoch(sched_latency_ns) meaning that running tasks will get more time to finish their work. I can understand this being a very good thing for applications with very few threads, but for eg. apache or other processes with a lot of threads would this not be counter-productive?

  Read the article

• Is it a good idea to run Redmine using Webrick through Nginx?

  - by Rohit

  The task here is to get Redmine setup for a small (<20) team. There may be a few users who would access the setup as business clients. I am familiar with setting up PHP for Apache, and recently, Nginx. I am not familiar with Ruby, Ruby-On-Rails, etc. I prefer to use the OS's (Ubuntu Linux LTS) package manager to install the different components as it takes care of dependencies and updates. I have setup Nginx with PHP-FPM successfully and am struggling with Redmine. As suggested here, I got Redmine running on port 3000. # /etc/init/redmine.conf # Redmine description "Redmine" start on runlevel [2345] stop on runlevel [!2345] expect daemon exec ruby /usr/share/redmine/script/server webrick -e production -b 0.0.0.0 -d And using the Nginx config on this page, I used Nginx to proxy requests to Webrick. server { listen 80; server_name myredmine.example.com; location / { proxy_pass http://127.0.0.1:3000; } } This works well locally. I wanted some opinions before trying this out on the live box (a 256 MB VPS). Further, should I use something like monit to monitor webrick for failure?

  Read the article

• gitweb- fatal: not a git repository

  - by Robert Mason

  So I have set up a simple server running debian stable (squeeze), and have configured git. Using gitolite, I have all functionality (at least the basic clone/push/pull/commit) working. Installation of gitweb went without any issues. However, when I access gitweb, I get a gitweb screen without any repos listed. # tail -n 1 /var/log/apache2/error.log [DATE] [error] [client IP_ADDRESS] fatal: Not a git repository: '/var/lib/gitolite/repositories/testrepo.git' # cd /var/lib/gitolite/repositories/testrepo.git # ls branches config HEAD hooks info objects refs Here is what I see in /var/lib/gitolite/projects.list: testrepo.git And in /etc/gitweb.conf: # path to git projects (<project>.git) $projectroot = "/var/lib/gitolite/repositories"; # directory to use for temp files $git_temp = "/tmp"; # target of the home link on top of all pages #$home_link = $my_uri || "/"; # html text to include at home page $home_text = "indextext.html"; # file with project list; by default, simply scan the projectroot dir. $projects_list = "/var/lib/gitolite/projects.list"; # stylesheet to use $stylesheet = "gitweb.css"; # javascript code for gitweb $javascript = "gitweb.js"; # logo to use $logo = "git-logo.png"; # the 'favicon' $favicon = "git-favicon.png"; What is missing?

  Read the article

• Wildcard SSL and Apache configuration

  - by Nitai

  Hi all, I'm pulling my hard on this configuration, which probably is simply. I have a wildcard ssl certificate which is working. I have the website setup to run on domain.com under SSL. Now, I'm in need to run many subdomains (*.domain.com) on the same server with the same SSL certificate. Shouldn't be that hard, right? Well, I can't get it going. Point is, that the first config is another Tomcat server that serves another site and listens to domain.com and www.domain.com. The other config listens to *.domain.com and pulls the content from another Tomcat server. I already tried this whole setup with mod_rewrite, but simply don't see what I'm doing wrong. Any help very much appreciated. Here is my conf in Apache 2.2: <VirtualHost *:443> SSLEngine on SSLCertificateFile ... SSLCertificateKeyFile ... SSLCertificateChainFile ... ServerName domain.com ServerAlias www.domain.com ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPreserveHost On ProxyPass / ajp://localhost:8010/ ProxyPassReverse / ajp://localhost:8010/ </VirtualHost> <VirtualHost *:443> SSLEngine on SSLCertificateFile ... SSLCertificateKeyFile ... SSLCertificateChainFile ... ServerName domain.com ServerAlias *.domain.com ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPreserveHost On ProxyPass / ajp://localhost:8009/ ProxyPassReverse / ajp://localhost:8009/ </VirtualHost> Thanks.

  Read the article

• Sudoers file allow sudo on specific file for active directory group

  - by tubaguy50035

  I have active directory sign in working on an Ubuntu 12.04 box. When the user signs in, I have a script that runs that needs sudo permission (since it modifies the samba config file). How would I specify this in my sudoer's file? I've tried: %DOMAIN\\AD+Programmers ALL=NOPASSWD: /usr/local/bin/createSambaShare.php I've found various resources on the internet stating that this is how it would be done, but I'm not sure that I have the first part right. What are they using as the DOMAIN? The workgroup or the realm? I use Samba + winbind for active directory integration. Here's my smb.conf: [global] security = ads netbios name = hostname realm = COMPANYNAME.COM password server = passwordserver workgroup = COMPANYNAME idmap uid = 1000-10000 idmap gid = 1000-10000 winbind separator = + winbind enum users = no winbind enum groups = no winbind use default domain = yes template homedir = /home/%D/%U template shell = /bin/bash client use spnego = yes domain master = no EDIT: The users that should have access to run that script are all part of the Programmers group which has an Active Directory Domain Services Folder of Company.com/Staff/Security Groups (not sure if that matters or not).

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Website has become slower on a VPS, was much fast on a shared host. What's wrong?

  - by Arpit Tambi

  My shared host suspended my website stating system overload, so I moved my website to a VPS which has 4GB RAM. But for some reason the website has become very slow. This is the vmstat output - procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 0 0 3050500 0 0 0 0 0 1 0 0 0 0 100 0 0 Here's the Apache Benchmark output for a STATIC html page I ran on the server itself - Benchmarking www.ask-oracle.com (be patient)...apr_poll: The timeout specified has expired (70007) Total of 20 requests completed Update: Server Config: List item Centos 5.6 4 cores cpu 4 GB RAM LAMP stack with APC Wordpress Only one website It takes almost double time to load now, same website was much fast on shared hosting. I know I need to tweak some settings but have no clue where to start from? I have already tried to optimize apache, mysql etc. Update 2: CPU usage is low, see uptime output: 11:09:02 up 7 days, 21:26, 1 user, load average: 0.09, 0.11, 0.09 Update 3: When I load any webpage, browser shows "Waiting" for a long time and then page loads quickly. So I suspect server can accept only limited connections and holds extra connections in a waiting state. How to check this? Update 4: Following is the output on executing netperf TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to localhost.localdomain (127.0.0.1) port 0 AF_INET Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.00 9615.40 [root@ip-118-139-177-244 j3ngn5ri6r01t3]# Here are the Apache MPM settings from httpd.conf, do they look okay? <IfModule worker.c> StartServers 5 MaxClients 100 MinSpareThreads 50 MaxSpareThreads 250 ThreadsPerChild 125 MaxRequestsPerChild 10000 ServerLimit 100 </IfModule>

  Read the article

• How do I get basic ProxyPass to work on Apache 2.2.17?

  - by Ansis Malins

  I'm trying to get around the ERR_UNSAFE_PORT restriction in Chrome by making Apache reverse proxy other HTTP servers on the machine. I load mod_proxy with sudo e2enmod proxy I add ProxyPass /znc/ http://localhost:6667/ to my httpd.conf I restart Apache with sudo /etc/init.d/apache2 restart When I open up /znc/, I get 500 Internal Server Error. I added LogLevel debug, restarted apache, tried again, and got nothing suspicous: [Fri Oct 19 18:55:17 2012] [debug] proxy_util.c(1818): proxy: grabbed scoreboard slot 0 in child 21528 for worker http://localhost:6667/ [Fri Oct 19 18:55:17 2012] [debug] proxy_util.c(1934): proxy: initialized single connection worker 0 in child 21528 for (localhost) [Fri Oct 19 18:55:17 2012] [debug] proxy_util.c(1818): proxy: grabbed scoreboard slot 1 in child 21528 for worker proxy:reverse [Fri Oct 19 18:55:17 2012] [debug] proxy_util.c(1934): proxy: initialized single connection worker 1 in child 21528 for (*) [Fri Oct 19 18:55:17 2012] [notice] Apache/2.2.17 (Ubuntu) PHP/5.3.8 configured -- resuming normal operations [Fri Oct 19 18:55:17 2012] [info] Server built: Feb 14 2012 17:59:20 [Fri Oct 19 18:55:17 2012] [debug] prefork.c(1018): AcceptMutex: sysvsem (default: sysvsem) [Fri Oct 19 18:55:22 2012] [debug] proxy_util.c(1818): proxy: grabbed scoreboard slot 0 in child 21532 for worker http://localhost:6667/ [Fri Oct 19 18:55:22 2012] [debug] proxy_util.c(1837): proxy: worker http://localhost:6667/ already initialized [Fri Oct 19 18:55:22 2012] [debug] proxy_util.c(1934): proxy: initialized single connection worker 0 in child 21532 for (localhost) [Fri Oct 19 18:55:22 2012] [debug] proxy_util.c(1818): proxy: grabbed scoreboard slot 1 in child 21532 for worker proxy:reverse [Fri Oct 19 18:55:22 2012] [debug] proxy_util.c(1837): proxy: worker proxy:reverse already initialized [Fri Oct 19 18:55:22 2012] [debug] proxy_util.c(1934): proxy: initialized single connection worker 1 in child 21532 for (*) So I'm stumped at this point. What to do? I'm running Ubuntu Server 11.10. ZNC responds with a correct 200 OK and HTML when queried directly both from the local machine and the Internet.

  Read the article

• MySQL Not Turning On

  - by Shalin Shah

  I have an amazon ec2 instance running on the Amazon Linux AMI and its a micro instance. I wanted to install Django onto my server so I entered these commands wget http://www.mlsite.net/blog/wp-content/uploads/2008/11/go wget http://www.mlsite.net/blog/wp-content/uploads/2008/11/django.conf chmod 744 go ./go So after I was done, I ran sudo service httpd restart and sudo service mysqld restart and This is what came up for mysqld: Stopping mysqld: [ OK ] MySQL Daemon failed to start. Starting mysqld: [FAILED] So I deleted the django files /usr/local/python2.6.8/site-packages/django_registration.egg and I tried finding the error and I found out that in my /etc/my.cnf for the socket, it said socket=/var/lock/subsys/mysql.sock so I went to /var/lock/subsys/ and there was no mysql.sock. I tried creating one using vim but it still didn't work. Then I checked the error log and it said Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) So I am pretty much lost right now. I know it has something to do with mysql.sock If you might know a reason why this was caused could you please let me know? I have a wordpress site on my server, so i kind of need MySQL to work. Thanks!

  Read the article

• Why is it necessary to chmod o+r parent directory to fix 403 access forbidden error with Nginx and P

  - by davenolan

  This may be an Nginx wrinkle, or it may be because I don't understand Unix permissions. We're using Hudson CI to deploy our staging instance. So RAILS_ROOT is /var/lib/hudson/jobs/JOBNAME/workspace. Hudson runs as hudson user Nginx runs as www-data user hudson and nginx are both members of the www group root of my nginx conf points to RAILS_ROOT/public as per normal. RAILS_ROOT/config/environment.rb is owned by www-data (so Passenger runs as www-data) RAILS_ROOT and everything in it is owned by the www group and group has r/w/x permissions As it stood, Nginx threw 403 permission denied when requesting any url. error.log contained entries like this: public/index.html" is forbidden (13: Permission denied). These did not fix the or change the error (each with a stop/start of Ngnix): chmod 777 -R RAILS_ROOT chgrp www -R /var/lib/hudson I also tried Nginx as root, and passenger complained that it could not find config/environment (despite the path displayed on the error page being correct). The fix was to ensure everybody has read permissions on each directory in the heirachy. In this case chmod o+r /var/lib/hudson. But if the group has read permissions on the directory, and nginx is a member of the owner group of the directory, why was it necessary to allow everyone read permissions? Is there something have not grokked about permissions? $nginx -V nginx version: nginx/0.7.61 built by gcc 4.4.1 (Ubuntu 4.4.1-4ubuntu8) configure arguments: --prefix=/opt/nginx --add-module=/usr/lib/ruby/gems/1.8/gems/passenger-2.2.5/ext/nginx --with-http_ssl_module --with-pcre=~/src/pcre-8.00/ --with-http_stub_status_module $cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=9.10 DISTRIB_CODENAME=karmic DISTRIB_DESCRIPTION="Ubuntu 9.10"

  Read the article

• How to avoid index.php in Zend Framework route using Nginx rewrite

  - by Adam Benayoun

  I am trying to get rid of index.php from the default Zend Framework route. I think it should be corrected at the server level and not on the application. (Correct me if I am wrong, but I think doing it on the server side is more efficient). I run Nginx 0.7.1 and php-fpm 5.3.3 This is my nginx configuration server { listen *:80; server_name domain; root /path/to/http; index index.php; client_max_body_size 30m; location / { try_files $uri $uri/ /index.php?$args; } location /min { try_files $uri $uri/ /min/index.php?q=; } location /blog { try_files $uri $uri/ /blog/index.php; } location /apc { try_files $uri $uri/ /apc.php$args; } location ~ \.php { include /usr/local/etc/nginx/conf.d/params/fastcgi_params_local; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_param SERVER_NAME $http_host; fastcgi_pass 127.0.0.1:9000; } location ~* ^.+\.(ht|svn)$ { deny all; } # Static files location location ~* ^.+\.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { expires max; } } Basically www.domain.com/index.php/path/to/url and www.domain.com/path/to/url serves the same content. I'd like to fix this using nginx rewrite. Any help will be appreciated.

  Read the article

• dovecot/postfix: can send & receive via webmin, however squirrel mail and outlook fail to connect

  - by Jonathan

  I have just finished setting up dovecot and postfix on my server (centos 5.5/apache) earlier today. So far I've been able to get email working through webmin (can send/receive to and from external domains). However, attempting to telnet xxx.xxx.xx.xxx 110 returns the following errors: Connected to xxx.xxx.xx.xxx. Escape character is '^]'. +OK Dovecot ready. USER mailtest +OK PASS ********* +OK Logged in. -ERR [IN-USE] Couldn't open INBOX: Internal error occurred. Refer to server log for more information. [2011-02-11 22:55:48] Connection closed by foreign host. Which further logs the following error dovecot: Feb 11 21:32:48 Info: pop3-login: Login: user=, method=PLAIN, rip=::ffff:xxx.xxx.xx.xxx, lip=::ffff:xxx.xxx.xx.xxx, TLS dovecot: Feb 11 21:32:48 Error: POP3(mailtest): stat(/home/mailtest/MailDir/cur) failed: Permission denied dovecot: Feb 11 21:32:48 Error: POP3(mailtest): stat(/home/mailtest/MailDir/cur) failed: Permission denied dovecot: Feb 11 21:32:48 Error: POP3(mailtest): Couldn't open INBOX: Internal error occurred. Refer to server log for more information. [2011-02-11 21:32:48] dovecot: Feb 11 21:32:48 Info: POP3(mailtest): Couldn't open INBOX top=0/0, retr=0/0, del=0/0, size=0 Also, when attempting to login to squirrelmail or access the account via thunderbird/live mail etc, it obviously fails with a similar issue. Any suggestions or outside thinking on this would be a massive help! I've pretty much exhausted every resource, and tried every suggestion for my dovecot.conf file, but so far nothing seems to work :( I feel like it may be a permissions/ownership issue, but i'm lost as to specifics.

  Read the article

< Previous Page | 181 182 183 184 185 186 187 188 189 190 191 192  | Next Page >