Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 187/391 | < Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >

• Windows route two logical networks on one NIC

  - by John Oxley

  I have a Windows 2003 server which has one NIC with two networks configured on it. There are two logical networks sharing the same layer 2 domain. How do I configure the server to route traffic between the two logical networks?

  Read the article

• What does this TCP Packet mean ?

  - by asksuperuser

  I'm total newbie at tcp/ip and I was experimenting with Wireshark. What this mean: 1824 578.194204 xxx.xxx.xxx.xxx yyy.yyy.yyy.yyy UDP Source port: 17500 Destination port: 17500 In data I can see that my user pc name is sent (happily it's a generic name): does this mean someone is trying to hack my pc ?

  Read the article

• Can't connect remotely to Windows Server 2008 R2

  - by JohnyD

  I have a new Dell R710 server running Windows Server 2008 R2. I one of it's 4 nic's set up and the rest are not being used. I have successfully given it an ip address, network mask, and dns servers. I can ping and resolve this machine from anywhere else in the network. However, when I try to connect to it via RDP it does several things: 1) it might just outright refuse me with the message, "This computer can't connect to the remote computer. Try connecting again." 2) it might connect me and let me chose the account I would like to log on as... but when you select an account then you receive the same message as in #1 3) it might actually allow you to connect but only for about 1 minute and then you receive the same message and it closes your session. I have configured the firewall service to allow for RDP over the domain network connection. This didn't have any noticible effect. I have now disabled the firewall for all 3 networks and have even stopped the Windows Firewall service. I am still having the same issue. I am new to Server 2008 R2 and things are very different. Please give me any advice you can on how to resolve this issue and/or any other gotchas that are sure to come my way. The 2003 - 2008 learning curve seems steep. Thanks

  Read the article

• Network monitoring solution

  - by Hellfrost

  Hello Serverfault ! I have a big distributed system I need to monitor. Background: My system is comprised of two servers, concentrating and controlling the system. Each server is connected to a set of devices (some custom kind of RF controllers, doesnt matter to my question), each device connects to a network switch, and eventually all devices talk to the servers, the protocol between the servers and the devices is UDP, usually the packets are very small, but there are really a LOT of packets. the network is also somewhat complex, and is deployed on a large area physically. i'll have 150-300 of these devices, each generating up to 100+ packets per second, and several network switches, perhaps on 2 different subnets. Question I'm looking for some solution that will allow me to monitor all this mess, how many packets are sent, where, how do they move through the network, bandwidth utilization, throughput, stuff like that. what would you recommend to achieve this? BTW Playing nice with windows is a requirement.

  Read the article

• Splitting build cross the network?

  - by Dandikas

  Is there a known solution for splitting build process cross the network machines? Use case: We are an average software development company. We own around 50 development workstations (Quad Core 2.66Ghz, 4 GB ram, 200 GB raid). No need to tell that at any single moment not every machine is loaded to the max. There are 5 to 15 projects running simultaneously at any single moment. Obviously all of them are continuously build on server, than deployed to proper environment. Single project build is taking from 3 to 15 minutes. The problem: Whenever we build 5 projects in a row the last project is going to be ready after around 25 - 50 minutes. Building in parallel does not solve the problem (build is only a part of the game, than you need to deploy, run tests etc.) YES the correct solution is to add another build server, but "That involves buying new Expensive hardware, and we already spent a lot!". Yea, right(damn them)! Anyway. What about splitting build among developers workstation? Lets say whenever we need to build project "A" we check 5 workstations and start build on all that are not overloaded. The build can be canceled by a developer if he really needs all the power of his machine as long as there is at least 1 machine that is still building. After build is finished deployment can be performed to a proper environment (hosted on some server, not on workstation :) ). The bigger the company the more this makes sense to me. Anyone tried something like this? Are there any good practices? Any helpful software?

  Read the article

• Managing two internet connections in Windows XP, with different applications using different connections

  - by user932867535

  I have two internet connections, one has limited data but is fast, the other has unlimited data but is slow. What am trying to do is assign the unlimited data connection to the application which is downloading a large file, while surfing the net (using Firefox) with the other, faster connection. I tried connecting both connections, but every time I do that, all the applications just jump from the slower connection to the faster one. Is there any way in which I could achieve what I am looking for?

  Read the article

• udhcpc doesn't assign ip address

  - by Diab

  i have a board running linux 2.6.28 and i have one Ethernet interface (eth0) i want dhcp to assign dynamic ip to this interface. i have busybox with udhcpc in the file system and the kernel has the "Pack Socket" enabled so i copied the scripts from "busybox-1.14.1/examples/udhcp" to my board on "/etc/udhcpc/" (i created this directory) and when i run : ifconfig eth0 up the interface is up but without ip address, then running udhcpc -i eth0 -s /etc/udhcpc/sample.script i get the following: note : sample.script contains : "exec /etc/udhcpc/sample.$1" # udhcpc -i eth0 -s /etc/udhcpc/sample.script udhcpc (v1.14.1) started Sending discover... Sending select for 192.168.10.198... Lease of 192.168.10.198 obtained, lease time 691200 but when i check with ifconfig i can see that it didn't assign the ip address to eth0. anyone have an idea why udhcpc didn't assign the ip ? Thanx

  Read the article

• Can a Linksys Router be the cause of bad speeds on a 1.5 mbps link.

  - by gramware

  We use a Linksys 5-port router at a smal organization with about 20 employees. We recently acquired a 1.5 mbps fibre link, but sometimes the link goes down and speeds are still low. On enquirey from the ISP, this was part of the response, However there maybe throttling due to the router in place. A Linksys is a low end router and may be unable to carried traffic of up to 1536Kbps. We are in a position to deploy a Cisco 871 router on test for 2 wks to eliminate that possibility. Also kindly advise the destination of the ping results they look to high. How true is that about the router throttling the network and need for a bigger one.

  Read the article

• What to use for server and network documentation? Must run on Linux.

  - by Louise Hoffman

  Does anyone know of a good program, web service, or CMS for documenting servers, IP addresses, logins, and network? Only requirement it must run on and from Linux.

  Read the article

• "Piping" to MPD

  - by oxinabox.ucc.asn.au

  I would like to "Pipe" the output of my local sound card to MPD on a networked music server. Anyone have any suggestions how to go about this? I'm thinking maybe i can make a live MP3 stream? maybe over the web, or over the intranet? (IIRC MPD supported MP3 streams, i've had Internet radio steams going (though I didn't set them up) I'm not very experienced with MPD, or with webcasts

  Read the article

• Fortigate 200A firewall CPU high resource usage

  - by user119720

  This morning I'm receiving complaints from several end users that saying their whole department network are slow and have intermittent. Therefore I've checked our firewall to see whether if something goes wrong with the device.From my observation in the FortiGate dashboard status, the CPU resources is very high (99 percent). My first assumption is to clear the log since in the alert log the Fortigate log mention that it is already 90% full.Based on my understanding,the log can be cleared by restarting the firewall. After restarting the firewall the network seems okay again but then after several minutes it went up again.The condition still persist until now. Can someone show me where else I can check to fix this issue? I've really appreciate any help that I can get here.Thanks. Edit: diag sys top command

  Read the article

• Anyone interested in obtaining a cable list from a visio Diagram? [closed]

  - by Alex

  it's my first post here. Just wondering if anyone had to deal with the following problem - you have to install over say a 100 network elements and servers - cabling is done via contractors, so you need to provide them with an accurate, error-free cable list - your inputs are a set of detailed, port by port, visio diagrams. Prb is to obtain the cable list and get the cabling started while you're busy crafting the switch/routers configs. I coded a Visio plugin, which I plan to release under the GNU license, that returns a cable list from a diagram, and tested it on intermediate size infrastructure, 2K+ cables. It works well. The tool needs a little work to be user friendly, so before getting started, I wanted to know if that was worth the effort. Questions are welcomed, let me know -A PS: the tool is targeted for those who need a port by port description of their network, in the form Source/slot/port/Destination/slot/port.

  Read the article

• Windows 7 - system error 5 problem

  - by ianhobson

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• Should I upgrade my LinkSys WRT54GL firmware?

  - by Reid

  I have a LinkSys WRT54GL v1.1 which currently has stock firmware version 4.30.7. I see that version 4.30.14 is available. The router works fine now, and the release notes look uninteresting except for one line in v4.30.9: "Resolves issue with Linux kernel vulnerability". I have remote management turned off. I'm aware of the 3rd-party firmwares but the stock firmware works fine for me at the moment, so I don't have an interest in those. Is the status quo fine or should I upgrade the firmware? (It's a bit of a pain since the config has to be saved and reloaded, and obviously any mucking with firmware is risky.)

  Read the article

• Printing on Windows 8 with PDF viewer (Adobe Reader) from network

  - by Bongo

  i have a problem with the Adobe Reader 8, but the problem seems to be equally bad with other pdf viewers. Here is the configuration: My PDF viewer is located on network drive "Z:" which is the network adress \dgs-main\progs. I tried to start the adobe reader from here - \\dgs-main\progs\Adobe\Reader 8.0\Reader\AcroRd32.exe and open the PDF from here - C:\Users\ServiceDesk\AppData\Local\Temp\GeneratedPDF.pdf The problem is as follows, if i open the PDF with a local PDF viewer everything works fine and i can print the document. If i open the PDF with the Network PDF viewer then it opens, but printing is impossible. The error message states: "Unable to start print job. Is printer available?" As mentioned above, it works with a local pdf viewer. In both cases i use the same printer. The Printer is a network printer but even with a local printer it fails. The error occurs only on Windows 8 machines. On windows 7 it works fine. I Hope somebody can tell me what the problem is. Thanks in advance and have a fine day.

  Read the article

• Mikrotik server networks and Cain & Abel

  - by user269742

  I'm connected to the internet via a mikrotik server network. Recently, I read about that scaring application named Cain & Abel and all the capabilities it offered for malicious users. I don't know if anyone on my network is using or even aware of such application but my questions are: 1- How to protect myself from this program? 2- How to know if someone using such application against me? 3- Is Tor Bundle capable of protecting me from Cain & Abel? 4- If I filled my e-mail password via SSL page, Can Cain & Abel collect it? 5- Is it safe to use SKYPE or Yahoo Messenger voice chat if some one using Cain & Abel on my network?

  Read the article

• pfsense CARP - wan failure on firewall

  - by eldblz

  I have recently configured 2 firewall (on 2 DELL PowerEdge R210II with ESXI 5.1) with pfsense. We have several LANs and 2 WANs. Everything is running fine but i have a strange behavior: i can access internet from alla LANs but not from the firewall (itself). For example the firewall cannot retrive package information or if i setup a gatway monitor ip (like google 8.8.8.8 ) this fails. These are the screenshots of firewall configuration: http://imgur.com/a/LNuMz#0 ATM i kept firewall rules to minimum to avoid problem or conflicts. Any ideas how to solve the problem? Thank you in advance.

  Read the article

• Bandwidth Suggestion

  - by Campo

  I have been asked to analyze the bandwidth usage of a company and make a recommendation for upgrading their Internet connection(s). Here is the layout 3 DLS lines so it is 3x(6 Down, 1 Up Each) into a load balancer out to the office's network. 30 VOIP phones run on a T1 (1.5 Down, 1.5 Up) The users at the company are heavily uploading. It is my suspicion that the issue in slowdown is being cause by multiple people uploading and others not being able to get requests out for even simple http requests. My initial idea is to get them a fiber line with a 10 down and 10 up. What do others think on this plan? Will that be enough to host their network traffic? What do I do about the VOIP line afterward? The fiber is expensive and I know the T1 does a great job for their VOIP so I do not want to suggest a DSL line because I know it may not be sufficient. I would also like to save them some money if I can. Maybe even get a faster fiber line and forgo the T1. Though I know their load balance/switch can only handle 20MB/S throughput. Looking for some confirmation/suggestions on my plan. I am planning on going in to get some real diagnostic numbers. Any suggestions on software to use for that? Preferably Windows software.

  Read the article

• design a large scale network for an organization

  - by Essam

  i want to design a large scale network for an organization with HQ and two branches. i want to use a class A subnet. if i am using the network address 30.0.0.0 for the whole organization how can it be different from another organization company or whatever which is using the same address in another country? now i have the three locations for this organization,so i need 5 subnets [one for the HQ,two for branch A and branch B , one for connecting A to HQ and one for connecting branch B with HQ since i will use central DHCP server at the HQ,is that (number of subnetting) right? is it advisable to use class A or class B for this organization it term of address that will be wasted (let's say it is a university with two branches in two different states)?!

  Read the article

• Automatic layout of manual network mapping

  - by Paul

  So I have a small business network mainly consisting of two routed layer-2 domains with a total of ca. 100 devices spread over ca. 2000m² production and office spaces. Typical problems to solve using the graph would be: Over what (cable) path is a PC connected to the server? Where to expect devices connected to a switch port? I want to generate a graph of the physical network topology: Nodes are endpoint devices, switch ports, wall outlets, patch panel ports etc. Edges are cable connections. Ideally, grouping edges (or segments) that pass through the same bundle could be grouped. Also I would like to augment the graph data with automatically gathered data (monitoring state, MAC address, Switch port <- MAC entries to build up parts of the map). At the moment I use graphviz for this inside a Confluence wiki like that: layout = "neato" overlap = scale subgraph { rankdir = "TB" subgraph cluster_r1pf1 { r1pf1 [label="{ Rack 1 PF 1 | { <p1>P1 | <p2>P2 | <p3>P3} }", shape=record] } subgraph cluster_switch1 { switch1 [label="{ Rack 1 Switch 1 | { <p1> P1 | <p1> P1 | <p3> P3} }", shape=record] } r1pf1:p1 -> switch1:p1 (obviously there are dozens of entries omitted here) Problem is: I have a hard time to influence graphviz to generate a bearable layout. Edges overlap so bad that you can't read the diagram anymore. The question is: What other tools (be it interactive like Visio, Omnigraffle or I/O-oriented like graphviz) exist that would allow an easily versionable (as in: Operates on a text file) documentation that is both machine and human readable and editable? Why not OmniGraffle or Visio? Well we don't have Macs and Visio is not available at the moment. To buy it I would need good arguments. Automation would be one of that. But last time I looked, versioning Visio files or even thinking about automatic handling was a nightmare. Related: Network Mapping Tools basically asks the same with a focus on generating the complete graph automatically (but without the need to document cabling connections) Recommendations for automatic computer inventory brings up links of "all-in-one" solutions

  Read the article

• Enabling NAT loopback on HG556a router?

  - by galdikas

  This is one of the standard issue vodafone routers. So i set up web-server on my laptop, and it is accessible to the internet now. However I need to be able to access it from my machine using the public address. But I just cannot find where to enable nat loopback. I looked for options in both regular and advanced user logins (web interfaces). So I suppose the last option is telneting into it, and using commands to do it.. but I don't know how to access it (cant find the credentials). http://rhiggins.sdf-eu.org/blog/index.php?entry=entry110722-164625 In above link it says that i can find this info in configuration file, but anyone could tell me how to access it? And then what commands should I use to enable the NAT loopback?

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Virus blocking incoming connections ?

  - by Benoît

  Hello, on my windows 2003 server, all incoming connections are dropped. I can see them getting in using Wireshark, but even a single ping from another computer fails. All locally initiated connection work fine (i'm asking from the server). This server is the DC/DHCP/DNS/File server, so computer clients are in the dark. I've run varius antivirus and removal tools without any luck. The Windows Firewall is disabled. I'm wild-guessing at some virus/worm. How can i check why these incoming ICMP/TCP SYN/etc are dropped ? Anyone has any knowledge about such situations ? Thanks.

  Read the article

• freeradius maximum session time problem

  - by haw3d

  hello I'm using openvpn and free-radius for control user accounts. for maximum session time for an user, free-radius has sqlcounter.conf that control that, but after a connection has disconnected that is useful and cannot destroy a connection. for control account time dynamically i need another script that do that. but should anytime that a connection has established a trigger run. is anyway to fire a custom trigger or script when a connection has established? or any way to control session time dynamically?

  Read the article

< Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >