Search Results

Search found 12790 results on 512 pages for 'port islander 2009'.

Page 209/512 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

  • Is Winpcap able to capture all packets going through a Gigabit NIC without missing any packets?

    - by Patrick L
    I want to use Winpcap to capture all network packets going through a Gigabit NIC of a server. Assuming that I am able to utilize the network link up to 100%, the maximum network speed is 1000Mbps. If we exclude the TCP/IP headers, the maximum TCP data rate should be roughly 940Mbps. Let's say I send a 1GB file through the NIC at 940Mbps using TCP destination port 6000. I use Winpcap to capture all network packets going through the NIC and then dump it to a pcap file. If I use Wireshark to analyze the pcap file and then check the sum of packet size for all network packets sent to TCP port 6000, am I able to get exactly 1GB from the pcap file? Thanks.

    Read the article

  • Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

    - by Martin
    Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

    Read the article

  • Connecting to local Sql server 2005 through Internet

    - by Manish
    Hello My Sql server is on Local Machine, I want to access it through Internet. I Configure Surace manager and Configuration manager of sqlserver 2005 for remote access. My sqlserver is running on port:1433 I am using port forwarding , I can access service of other ports, My Connetion String Is: Data Source=190.190.200.100,1433;Network Library=DBMSSOCN;Initial Catalog=myDataBase;User ID=myUsername;Password=myPassword; But it gives following error when i am trying to connect sql server through internet: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

    Read the article

  • external HDD with SATA & USB interface?

    - by Greg
    Anyone know of an external HDD that would have (in addition to USB) a SATA (eSATA) port/cable? i.e. Brand/Model. Preferably one of the name brands so I have a better change of finding it here or locally if possible. Background - In one location I want to use it is I would like to increase the performance by cabling it directly to the PC SATA port, HOWEVER I don't want to have to open up the PC to do this each time. I was thinking of running a SATA cable out through the PC case so I just plug it directly into the external HDD in question. Perhaps it should be also externally powered too so I don't need to run a power cable out from the PC power supply.

    Read the article

  • new ubuntu server installation - java server not receiving packets

    - by James
    I have developed a Java server which listens for UDP packets which come from mobile devices. At the moment, it works correctly if I run my Server on my windows PC. I can receive and respond to the UDP packets sent from my phone (over 3g, not wifi). However, I am trying to run the Server on a different computer which I found lying around my house. I have basically done a clean install of Ubuntu Server edition, updated it, installed the java run time environment and configured port forwarding to allow connections on the appropriate port. I have also tried to disable the firewall. The problem is, it doesn't appear as if the server is receiving any packets and I've exhausted my brain thinking on how to solve/debug the problem. Can anyone suggest to me what the problem might be? or more likely something I can do to help me find out more information about what is going wrong.

    Read the article

  • Routing and Remote access rule not being applied internally (Windows SBS)

    - by Tim Saunders
    Hi, I have a Microsoft Small Business Server. I have pointed an external domain name to the external fixed IP address for the server. In routing and remote access I have defined a service for our subversion server as follows: Incoming port: 8443 Private address: 192.168.10.5 Outgoing port: 8443 192.168.10.5 is our development server, not the SBS (which is at 192.168.10.1) This rule works correctly if I am not on our internal network. However if I am on the internal network this rule does not get applied. What can I do/set so this rule is applied both internally and externally (so users with laptops et, don't keep having to change the URL by which they access the subversion server) Not sure what other info you may need, so please let me know if more details are required. T

    Read the article

  • Plesk 9 VPS - Doesn't reply to NameServer requests (nslookup, etc)

    - by Ben
    Hi, I'm trying to troubleshoot a problem with a new VPS i'm setting up. The VPS is running Plesk 9 on a CentOS 5 system. Everything works fine, except it doesn't serve dns requests. If I try something like nslookup [somedomain.com] the.ser.ver.ip to test a DNS query, i get the following error ;; connection timed out; no servers could be reached I can't telnet to it on port 42 either.. I'm guessing something is blocking the requests.. firewall maybe? the plesk firewall module is installed and the nameservers entry is green. Any other way I can check what's blocking it on the server? Any help/tip greatly appreciated. Note: http works, i can telnet to the server on port 80 and i can also ping the server Thanks

    Read the article

  • squid transparent proxy on all ports

    - by Yves Richard
    I have setup squid as a transparent proxy by redirecting port 80 to the native squid port 3128. I know there are issues with getting secure ports like ssl and imaps to go though the proxy but can I redirect all other ports through the proxy as well. I am trying to get a better idea of bandwidth usage. I have setup iptables to log usage and i am getting most traffic going into the related/established rule. I am trying to determine the origins of this traffic by sending traffic to squid for more detailed logging.

    Read the article

  • Running NginX (with Apache) and cPanel/WHM

    - by ub3rst4r
    I was wondering if its a good idea to be running NginX as the webserver (on port 80) and Apache as the reverse proxy (on port 8080) with cPanel/WHM being used as a control panel? I also installed Nginx Admin so the configuration for NginX is managed by WHM. The reason I am asking is because I came across an article (http://kbeezie.com/view/apache-with-nginx/) which explains how to setup Apache as a reverse proxy but it states If you are using a control panel based hosting such as cpanel/whm, this method is not advised. Most of the servers configuration is handled automatically in those cases, and making manual changes will likely lead to problems (plus you won’t get support from the control panel makers or your hosting provider in most cases). Anyone have any past experiences with this and can say if its good/bad idea?

    Read the article

  • Building boost 1.42 on FreeBSD 6.3

    - by Ivan Perekluyev
    Hi, i need to build mapnik on freebsd 6.3, but port marked as 'broken', so i forced to build it from source. With boost 1.41 (which is in ports) mapnik doesn't build. somewhere in internet, i found that mapnik successfully builded with boost 1.42. So, i download patch from wiki.freebsd.org/BoostPortingProject andd apply it: wget http://alexanderchuranov.com/boost-port/boost-from-1.41-to-1.42-2010-02-16-17-11.diff cd /usr/ports patch -p0 -i ~/boost-from-1.41-to-1.42-2010-02-16-17-11.diff after that, i trying to install boost-all metaport, but its failed. cd devel/boost-all make install 2>&1 | tee build.log tail -n 100 build.log > short_build.log Build.log (attention, 5m !): dl.dropbox.com/u/7365614/build.log Short build log: http://paste.pocoo.org/show/224474/ Thanks!

    Read the article

  • Get/Assign IP addresses assigned by the DHCP sever with DLink switches in between

    - by Ranjith Kumar
    In our office the setup is like we have a UBUNTU server with DHCP Server connected to all the PCS via 24 port and 8 port DLink switches. How can I find all the PCS(with client name, ip and mac address)in the network?? When I do "vi /var/lib/dhcp3/dhcpd.leases", I get all the ip addresses for the switches. I have used "arp-scan --interface=eth0 --localnet" to get all the IPs and MAC Addresses in my local network. I couldn't find any option to diplay client name. Also I would like to assign particular IP for a particular PC. I have done the changes in the dhcp.conf file but it is not working as they are not directly connected to DHCP-server(DLink switches in between). How can I assign IPs for PCs in this kind of setup. Thanks in advance

    Read the article

  • Routing from the DMZ to the interior network only

    - by Allan
    I have a home network connected to Verizon's FIOS service. Verizon's ActionTec router is connected to the ONT via coax to establish the MOCA network. My DD-WRT router's WAN port is connected to one of the ActionTec's LAN ports. The DD-WRT router is configured with a static IP address and assigned to the DMZ (this is done so I only have to configure port forwarding once). My issue is that this does not allow computers connected to the DD-WRT to serve streaming audio/video to the MOCA network using Verizon's Media Manager. I know that Media Manager uses ports 18001, 5050, and 5060, but I don't know how to forward those ports so that they are only available to the ActionTec's network and not the rest of the internet.

    Read the article

  • NTP doesn't sync

    - by Jonathan
    I'm using Meinberg NTP to sync the time in a VPS. The clock refuses to sync - there's a ~30s shift comparing to other servers. Meinberg NTP comes with a status script that checks hte delay\jitter every 10s and it is showing all zeros. Actions I've taken which didn't help: Restarted the NTP service using a script that comes with Meinberg NTP Added port 123 for UDP and TCP as an exception port to Windows Firewall Added Meinberk NTP executables as an exception program to Windows Firewall validated iburst appears after each server listed in the configuration file Restarted the server The OS is a Windows Server Standard SP2 32bit. What did I miss?

    Read the article

  • Concerns about a Dedicated (Windows Server 2008) + DDoS

    - by TheKillerDev
    I am have today a dedicated server with these specs: Intel Core i5 750, 2x120GB (ssd + raid), Windows Server 2008 Web, 200Mbps Network, 24 Gb DD3 And I would like to know what are the best thing I can do to prevent a DDoS Attack, since I know this will be a real threat by the importance of the files that will be archived in it. Today I have apache listening port 80 and RDC listening port 3389. But the security is beeing made only by Windows Firewall. So, any thoughts on what would be good to prevent from DDoS attacks?

    Read the article

  • Can a switch consume bandwidth?

    - by aashiq
    I have a network with a router and a switch. At first my ISP's optical fiber is connected with media converter input port. Than Ethernet cable (output port of Media converter) is connected with the switch. Then an output Ethernet cable is connected with our inner Microtik router. Then this router is connected with another LAN switch. From this switch we have got every connection other switch. It is our total network structure. Our bandwidth is 2 Mbps. From the 11th of March our MRTG graph shows high all the time even when my all switch is switched off except LAN switch. That's why our line is breaking up (Voice call). How could be it possible? My all PC's bandwidth is limited but when connected PC with media converter directly then the graph shows normal. That's why I can't blame my ISP.

    Read the article

  • IIS web service responds on server, not from remote client

    - by Aharon Manne
    I have installed a web service on a server running IIS (v6, as far as I can tell). There is another service installed, which responds as expected. My service responds correctly when a browser is pointed to localhost, but there is no response when a remote client tries to query the service. Fiddler on the remote client simply reports a timeout. Wireshark on the remote client shows no response at all from the server, no NACK, nothing. Wireshark on the server detects no query at the relevant port (the service is installed on port 8080). There are no relevant entries in the event viewer. Obviously there is some issue of permissions or authentication. I have tried to compare my service to the service that works, but I have not been able to locate relevant parameters. Any help would be greatly appreciated.

    Read the article

  • apache redirect to https for basic auth

    - by shreddd
    I have a tricky variation on an old problem. I have an apache based site that should generally be accessed via http/port 80. However for certain areas protected areas that require authentication (designated by .htaccess), I want to be able to redirect the user the https/port 443. The key here is that I want this to always happen - i.e. I don't want to have to rewrite each htaccess file with a redirect. I only want to enforce this for basic authentication and the protected areas are scattered all over the site. Is it possible to somehow redirect all basic authentication requests to the SSL host?

    Read the article

  • How to failover to local account on a cisco switch/router if radius server fails?

    - by 3d1l
    I have the following configuration on a switch that I testing for RADIUS authentication: aaa new-model aaa authenticaton login default group radius local aaa authentication enable default group radius enable aaa authorization exec default group radius local enable secret 5 XXXXXXXXX ! username admin secret 5 XXXXXXXXX ! ip radius source-interface FastEthernet0/1 radius-server host XXX.XXX.XXX.XXX auth-port 1812 acct-port 1813 key XXXXXXXXX radius-server retransmit 3 ! line con 0 line vty 5 15 Radius authentication is working just fine but if the server is not available I can not log into the router with the ADMIN account. What's wrong there? Thanks!

    Read the article

  • 2wire modem to linksys router

    - by Imajica666
    I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

    Read the article

  • Setup IIS 7 as FTP Server that is connectable outside of my local network

    - by Usta
    I was able to setup an FTP site that I was able to access via ftp://127.0.0.1/ or my local(static) ip. To do this I followed these instructions (with the exception that I did not bind to 127.0.0.1 as suggested) http://learn.iis.net/page.aspx/301/creating-a-new-ftp-site-in-iis-7/ I have created a firewall exception for port 20 and 21, and setup port-forwarding on my wireless router. But I can only access the site via local-host, and I need to have a friend have read access to it. So how do I enable remote access to it? (I'd rather not purchase a domain-name) My setup: IIS 7.5 Windows 7 Professional Wireless Network Norton Internet Security 2012 An Internal Static IP Address

    Read the article

  • Setting up wifi router as a switch for Internet Connection Sharing

    - by William C
    Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

    Read the article

  • Reverse proxy using hop and RDP

    - by Sergei
    I am trying to connect from Vista to XP using RDP via reverse proxy using putty and an intermidiate host. There are myriad articles on the internet how to do it using vnc, ssh servers, winsshd, etc, but I can't find anything that helps me in this specific case. What I have: Windows XP host behind the firewall - 'destination' linux host running ssh on the internet - 'intermediate' windows host behind the firewall - 'source' All I want to do is open reverse tunnel from destination to intermidiate and use this tunnel for connecting back from the source. That should be simple to setup, however I just cannot make it. This is what I do: On 'destination', open putty session, create tunnel to 'intermediate' using following settings: source port 3389, destination is 'source:33389', direction is local On 'source', open putty session, create tunnel to 'intermediate'using following settings: source port 33389, destination is 'destination:33389', direction is local Finally, on source, open termnal services client and connect it to localhost:33389.Unfortunately it seems like packets do go somewhere but eventually client times out. Am I totally misunderstanding the concept? Please help!

    Read the article

  • Eventlog entry for allowed connection in Windows Firewall

    - by Jaap
    I was seeing a lot of entries in the eventlog: The Windows Filtering Platform has permitted a connection. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 10.xxx.xxx.xxx Source Port: 80 Destination Address: 10.xxx.xxx.xxx Destination Port: 31773 Protocol: 6 Filter Information: Filter Run-Time ID: 67903 Layer Name: Receive/Accept Layer Run-Time ID: 44 We have a loadbalancer which checks every second to see if the application is still running (a health check). The logs contain large amounts of this kind of entries, which makes the Event Viewer slow and it's difficult to find the more interesting logs. How do I make sure these messages don't end up in the event logs?

    Read the article

  • What's causing "shutdown state" after TFTP reloaded Cisco `running-config` on 871?

    - by xtian
    Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I tested the 871's flash memory with fsck and rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config?

    Read the article

  • Apache not directing to correct VHost

    - by BANANENMANNFRAU
    I have setup the following virtual host ServerAdmin [email protected] ServerName mysite.com ServerAlias www.mysite.com DocumentRoot /var/www/homepage/public_html ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined When I hit my url Apache still shows the default page. Not the index Ive created in the give Document root. In my Domain i have set the A Record to the Ip of my VPS: apache2ctl -S: output: VirtualHost configuration: *:80 is a NameVirtualHost default server xxxxxx.stratoserver.net (/etc/apache2/sites-enabled/000-default.conf:1) port 80 namevhost xxxxxxx.stratoserver.net (/etc/apache2/sites-enabled/000-default.conf:1) port 80 namevhost mysite.com (/etc/apache2/sites-enabled/homepage.conf:1) alias www.mysite.com ServerRoot: "/etc/apache2" Main DocumentRoot: "/var/www" Main ErrorLog: "/var/log/apache2/error.log" Mutex default: dir="/var/lock/apache2" mechanism=fcntl Mutex mpm-accept: using_defaults Mutex watchdog-callback: using_defaults PidFile: "/var/run/apache2/apache2.pid" Define: DUMP_VHOSTS Define: DUMP_RUN_CFG User: name="www-data" id=33 not_used Group: name="www-data" id=33 not_used How would I need to setup my Virtual host so that apache shows the correct site depending on the Domain im redirecting from.

    Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >