Search Results

Search found 12790 results on 512 pages for 'port islander 2009'.

Page 210/512 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

• What's causing "shutdown state" after TFTP reloaded Cisco `running-config` on 871?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I tested the 871's flash memory with fsck and rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config?

  Read the article

• Connecting to local Sql server 2005 through Internet

  - by Manish

  Hello My Sql server is on Local Machine, I want to access it through Internet. I Configure Surace manager and Configuration manager of sqlserver 2005 for remote access. My sqlserver is running on port:1433 I am using port forwarding , I can access service of other ports, My Connetion String Is: Data Source=190.190.200.100,1433;Network Library=DBMSSOCN;Initial Catalog=myDataBase;User ID=myUsername;Password=myPassword; But it gives following error when i am trying to connect sql server through internet: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

  Read the article

• Host not visible in ECC after pushing master agent on server

  - by wildchild

  Hi all!! ECC master Agent has been pushed to one of the servers.. Once a Master Agent installed the host should appear within ECC.However, I am unable to see the host. I asked the Server team to stop and start the master agent ,and to check whether required port is enabled, so that server can talk with ECC server. After restarting the service I get an error.I even checked if the port is used by any other service ,it is not.. Somebody plz help what should done here..it’s a Windows server. Here's the error:- "The EMC control Center Master agent service on local computer atrted and the stopped.Some services stopped automatically if they 've no work to do,for example prformance logs and alert services" Thanks in advance!!

  Read the article

• Nginx, proxy passing to Apache, and SSL

  - by Vic

  I have Nginx and Apache set up with Nginx proxy-passing everything to Apache except static resources. I have a server set up for port 80 like so: server { listen 80; server_name *.example1.com *.example2.com; [...] location ~* \.(?:ico|css|js|gif|jpe?g|png|pdf|te?xt)$ { access_log off; expires max; add_header Pragma public; add_header Cache-Control "public, must-revalidate, proxy-revalidate"; add_header Vary: Accept-Encoding; } location / { proxy_pass http://127.0.0.1:8080; include /etc/nginx/conf.d/proxy.conf; } } And since we have multiple ssl sites (with different ssl certificates) I have a server{} block for each of them like so: server { listen 443 ssl; server_name *.example1.com; [...] location ~* \.(?:ico|css|js|gif|jpe?g|png|pdf|te?xt)$ { access_log off; expires max; add_header Pragma public; add_header Cache-Control "public, must-revalidate, proxy-revalidate"; add_header Vary: Accept-Encoding; } location / { proxy_pass https://127.0.0.1:8443; include /etc/nginx/conf.d/proxy.conf; proxy_set_header X-Forwarded-Port 443; proxy_set_header X-Forwarded-Proto https; } } server { listen 443 ssl; server_name *.example2.com; [...] location ~* \.(?:ico|css|js|gif|jpe?g|png|pdf|te?xt)$ { access_log off; expires max; add_header Pragma public; add_header Cache-Control "public, must-revalidate, proxy-revalidate"; add_header Vary: Accept-Encoding; } location / { proxy_pass https://127.0.0.1:8445; include /etc/nginx/conf.d/proxy.conf; proxy_set_header X-Forwarded-Port 443; proxy_set_header X-Forwarded-Proto https; } } First of all, I think there is a very obvious problem here, which is that I'm double-encrypting everything, first at the nginx level and then again by Apache. To make everything worse, I just started using Amazon's Elastic Load Balancer, so I added the certificate to the ELB and now SSL encryption is happening three times. That's gotta be horrible for performance. What is the sane way to handle this? Should I be forwarding https on the ELB - http on nginx - http on apache? Secondly, there is so much duplication above. Is the best method to not repeat myself to put all of the static asset handling in an include file and just include it in the server?

  Read the article

• Reverse proxy using hop and RDP

  - by Sergei

  I am trying to connect from Vista to XP using RDP via reverse proxy using putty and an intermidiate host. There are myriad articles on the internet how to do it using vnc, ssh servers, winsshd, etc, but I can't find anything that helps me in this specific case. What I have: Windows XP host behind the firewall - 'destination' linux host running ssh on the internet - 'intermediate' windows host behind the firewall - 'source' All I want to do is open reverse tunnel from destination to intermidiate and use this tunnel for connecting back from the source. That should be simple to setup, however I just cannot make it. This is what I do: On 'destination', open putty session, create tunnel to 'intermediate' using following settings: source port 3389, destination is 'source:33389', direction is local On 'source', open putty session, create tunnel to 'intermediate'using following settings: source port 33389, destination is 'destination:33389', direction is local Finally, on source, open termnal services client and connect it to localhost:33389.Unfortunately it seems like packets do go somewhere but eventually client times out. Am I totally misunderstanding the concept? Please help!

  Read the article

• Routing from the DMZ to the interior network only

  - by Allan

  I have a home network connected to Verizon's FIOS service. Verizon's ActionTec router is connected to the ONT via coax to establish the MOCA network. My DD-WRT router's WAN port is connected to one of the ActionTec's LAN ports. The DD-WRT router is configured with a static IP address and assigned to the DMZ (this is done so I only have to configure port forwarding once). My issue is that this does not allow computers connected to the DD-WRT to serve streaming audio/video to the MOCA network using Verizon's Media Manager. I know that Media Manager uses ports 18001, 5050, and 5060, but I don't know how to forward those ports so that they are only available to the ActionTec's network and not the rest of the internet.

  Read the article

• Cannot access internet or remote network after connecting to Windows VPN

  - by Kiewic

  I set up a VPN by creating an incoming VPN connection (VPN server) in my Windows 8 machine at home (not a Windows Server). I forwarded the PPTP port in my router (port 1723) to this machine and enabled PPTP passthrough. In a second Windows 8 machine out of home, I created an outgoing VPN connection (VPN client). And I am able to connect to my home VPN, but I don't have access to any home resource or even internet. This is the output of the client ipconfig: And this are the settings of my VPN server: UPDATE: My VPN server has assigned the 192.168.1.144 IP adress at my home network. So, I tried setting the "IP address assignment" range from 192.168.1.150 to 192.168.1.200. And when a VPN client gets connected, it gets an address in that range, but it doesn't make any difference.

  Read the article

• SSH stops at "using username" with IPTables in effect

  - by Rautamiekka

  We used UFW but couldn't make the Source Dedicated ports open, which was weird, so we purged UFW and switched to IPTables, using Webmin to configure. If the inbound chain is on DENY and SSH port open [judged from Webmin], PuTTY will say using username "root" and stops at that instead of asking for public key pw. Inbound chain on ACCEPT the pw is asked. This problem didn't happen with UFW. Picture of IPTables configuration in Webmin: http://s284544448.onlinehome.us/public/PlusLINE%20Dedicated%20Server,%20Webmin,%20IPTables,%200.jpgThe address is to the previous rautamiekka.org. iptables-save when on INPUT DENY: # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *mangle :PREROUTING ACCEPT [1430:156843] :INPUT ACCEPT [1430:156843] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1415:781598] :POSTROUTING ACCEPT [1415:781598] COMMIT # Completed on Wed Apr 11 16:09:20 2012 # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *nat :PREROUTING ACCEPT [2:104] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT # Completed on Wed Apr 11 16:09:20 2012 # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *filter :INPUT DROP [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1247:708906] -A INPUT -i lo -m comment --comment "Machine-within traffic - always allowed" -j ACCEPT -A INPUT -p tcp -m comment --comment "Services - TCP" -m tcp -m multiport --dports 22,80,443,10000,20,21 -m state --state NEW,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m comment --comment "Minecraft - TCP" -m tcp --dport 25565 -j ACCEPT -A INPUT -p udp -m comment --comment "Minecraft - UDP" -m udp --dport 25565 -j ACCEPT -A INPUT -p tcp -m comment --comment "Source Dedicated - TCP" -m tcp --dport 27015 -j ACCEPT -A INPUT -p udp -m comment --comment "Source Dedicated - UDP" -m udp -m multiport --dports 4380,27000:27030 -j ACCEPT -A INPUT -p udp -m comment --comment "TS3 - UDP - main port" -m udp --dport 9987 -j ACCEPT -A INPUT -p tcp -m comment --comment "TS3 - TCP - ServerQuery" -m tcp --dport 10011 -j ACCEPT -A OUTPUT -o lo -m comment --comment "Machine-within traffic - always allowed" -j ACCEPT COMMIT # Completed on Wed Apr 11 16:09:20 2012 iptables --list when on INPUT DENY: Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere /* Machine-within traffic - always allowed */ ACCEPT tcp -- anywhere anywhere /* Services - TCP */ tcp multiport dports ssh,www,https,webmin,ftp-data,ftp state NEW,ESTABLISHED ACCEPT tcp -- anywhere anywhere /* Minecraft - TCP */ tcp dpt:25565 ACCEPT udp -- anywhere anywhere /* Minecraft - UDP */ udp dpt:25565 ACCEPT tcp -- anywhere anywhere /* Source Dedicated - TCP */ tcp dpt:27015 ACCEPT udp -- anywhere anywhere /* Source Dedicated - UDP */ udp multiport dports 4380,27000:27030 ACCEPT udp -- anywhere anywhere /* TS3 - UDP - main port */ udp dpt:9987 ACCEPT tcp -- anywhere anywhere /* TS3 - TCP - ServerQuery */ tcp dpt:10011 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere /* Machine-within traffic - always allowed */ The UFW rules prior to purging on INPUT DENY: 127.0.0.1 ALLOW IN 127.0.0.1 3306 DENY IN Anywhere 20,21/tcp ALLOW IN Anywhere 22/tcp (OpenSSH) ALLOW IN Anywhere 80/tcp ALLOW IN Anywhere 443/tcp ALLOW IN Anywhere 989 ALLOW IN Anywhere 990 ALLOW IN Anywhere 8075/tcp ALLOW IN Anywhere 9987/udp ALLOW IN Anywhere 10000/tcp ALLOW IN Anywhere 10011/tcp ALLOW IN Anywhere 25565/tcp ALLOW IN Anywhere 27000:27030/tcp ALLOW IN Anywhere 4380/udp ALLOW IN Anywhere 27014:27050/tcp ALLOW IN Anywhere 30033/tcp ALLOW IN Anywhere

  Read the article

• Why does a redirect from a local IP address assume localhost?

  - by Jeremy

  I am developing a web application on my desktop and it is running on port 80. I am able to access the application from my laptop connected to the LAN by entering my desktop's LAN IP address 192.168.1.8. Now, my application sends a redirect after login, but my laptop assumes the final address is localhost/login. If I manually type in the IP address and URI for any page, it shows that I am logged in, so it works as expected. So, why does the redirect assume localhost? Both of my machines are linux-based. The laptop being Chrome OS. I am running nginx which proxies non-static file requests to jetty on port 8080.

  Read the article

• Routing and Remote access rule not being applied internally (Windows SBS)

  - by Tim Saunders

  Hi, I have a Microsoft Small Business Server. I have pointed an external domain name to the external fixed IP address for the server. In routing and remote access I have defined a service for our subversion server as follows: Incoming port: 8443 Private address: 192.168.10.5 Outgoing port: 8443 192.168.10.5 is our development server, not the SBS (which is at 192.168.10.1) This rule works correctly if I am not on our internal network. However if I am on the internal network this rule does not get applied. What can I do/set so this rule is applied both internally and externally (so users with laptops et, don't keep having to change the URL by which they access the subversion server) Not sure what other info you may need, so please let me know if more details are required. T

  Read the article

• Setting up wifi router as a switch for Internet Connection Sharing

  - by William C

  Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

  Read the article

• Amazon EC2 - Unable to connect to MySQL

  - by alexus

  I'm having issue connecting from one VM to another # nmap -p3306 ip-XX-XX-XX-XX.ec2.internal Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-10 17:50 EDT Nmap scan report for ip-XX-XX-XX-XX.ec2.internal (XX.XX.XX.XX) Host is up (0.000033s latency). PORT STATE SERVICE 3306/tcp closed mysql Nmap done: 1 IP address (1 host up) scanned in 1.05 seconds # in my Security Group I allowed Inbound connectivity via port TCP, portrange 3306 and Source 0.0.0.0/0, so theoratically it should work, but in reality it doesn't( I'm running red hat enterprise linux 7 on both VMs. mariadb.service running fine on another VM and I am able to connect to it locally. DB's: # netstat -anp | grep 3306 tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 2324/mysqld # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # Any ideas what else I missed?

  Read the article

• Does HyperV allow binding physical NIC on virtual machine with promiscues mode?

  - by MadBoy

  I have HyperV on Windows 2008 Enterprise R2 installed with some Virtual Server running that I wanted to have ISA or NTOP to monitor traffic. I've added additional physical NIC to server and wanted to use this NIC as traffic monitor (I've enabled port mirroring on switch). I can see on physical machine that runs HyperV a lot of traffic coming to the NIC so port mirroring works fine. However in virtual machine even thou I've assigned that NIC to only this one and only server it sees 0 packets. In VWMare Workstation it worked without problem and I could see mirrored traffic on VM. Should this be possible or HyperV is crippled?

  Read the article

• Varnish VCL not allowing two separate IP addresses as backends

  - by Peter Griffin

  Every time I attempt to add an extra back end into our VCL file, it's fails. Here is the DAEMON_OPTS we are running off: DAEMON_OPTS="-a :80 \ -T localhost:6082 \ -f /etc/varnish/custom.vcl \ -u varnish -g varnish \ -S /etc/varnish/secret \ -s malloc,10G" And here is the offending backend(s) backend default { .host = "114.123.456.789"; .port = "8080"; } backend alt { .host = "203.123.456.789"; .port = "80"; } Any Ideas ? Gut feeling is it might need the backends to be set somewhere, but I'm not sure where.

  Read the article

• Computer suddenly dies; screen displays weird flickering lines, then restarts

  - by Imray

  I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

  Read the article

• How to failover to local account on a cisco switch/router if radius server fails?

  - by 3d1l

  I have the following configuration on a switch that I testing for RADIUS authentication: aaa new-model aaa authenticaton login default group radius local aaa authentication enable default group radius enable aaa authorization exec default group radius local enable secret 5 XXXXXXXXX ! username admin secret 5 XXXXXXXXX ! ip radius source-interface FastEthernet0/1 radius-server host XXX.XXX.XXX.XXX auth-port 1812 acct-port 1813 key XXXXXXXXX radius-server retransmit 3 ! line con 0 line vty 5 15 Radius authentication is working just fine but if the server is not available I can not log into the router with the ADMIN account. What's wrong there? Thanks!

  Read the article

• Cisco access list logging. Why is there a difference between IPv4 and IPv6?

  - by growse

  I've got a Cisco 877 router. I've got an IPv4 access list and an IPv6 access list set up and configured similar to this: interface Dialer1 ... ip access-group INTERET-IN ipv6 traffic-filter IPV6-IN Each of these access lists has a final rule of deny ip/ipv6 any any log. However, in my syslog I notice that there's a difference in formatting between the two types of entries. IPv4 will say: %SEC-6-IPACCESSLOGP: list INTERNET-IN denied udp 88.89.209.63(137) -> 1.2.3.4(137), 1 packet Whereas the IPv6 list will say %IPV6_ACL-6-ACCESSLOGNP: list IPV6-IN/240 denied 59 2001:0:5EF5:79FD:14F9:B773:3EBA:3EE3 (Dialer1) -> 2001:800:1000:0::1, 8 packets Both have broadly the same information, but the IPv6 log entry is missing the protocol type and port, both of which are very useful if I'm trying to troubleshoot connectivity. Why is this? How do I get IPv6 deny logs to display the protocol and port used, if any?

  Read the article

• Linux: disbale USB without disabling power

  - by Ergot

  TLDR I want toggle between the following usages of a usb-port via the terminal: use like a normal usb-port only supply energy to charge Story I recently got me something like a magna doodle that can save your drawings to pdf, which can be moved to your computer via usb afterwards. Now the thing is that you can't save anything while it's plugged in. Because it's the only way to charge it, it bugs me that I can't find a software solution and laziness I want to keep it plugged in and toggle the connection to the computer only when needed. I noticed that it's charging and usable when it is plugged in and the computer is shut down or suspened. So I guess that there's a way to do it. Tech info computer: ThinkPad X201 Linux Kernel: 3.14.5-1-ARCH "Magna doodle": Boogie Board Sync

  Read the article

• Cisco Aironet 1200 Series AP Configuration

  - by nonterrorist

  I am attempting to configure a new CISCO Aironet 1200 Series Access Point to have a fixed IP. I have been searching online and I have come to the conclusion that the default IP address of this device is 10.0.0.1. These are the steps I have taken: My machine is plugged directly into the Ethernet port (not the Console port) of the AP. My Ethernet adapter is set to 10.0.0.2. I have reset the AP by holding the Mode button while powering up the device. The issue remains that I can not access 10.0.0.1 through the web, nor can I ping that address.

  Read the article

• PHP does not allow https connections

  - by FunkyChicken

  Hey guys im running PHP 5.4.0 and I cannot cURL nor files_get_content() https connections. Using curl in a PHP script shows: [root@ns1]# /opt/php/bin/php -q test.php * About to connect() to www.google.com port 443 * Trying 74.125.225.210... * connected * Connected to www.google.com (74.125.225.210) port 443 * successfully set certificate verify locations: * CAfile: /etc/pki/tls/certs/ca-bundle.crt CApath: none Segmentation fault Using file_get_contents() shows: Warning: file_get_contents(): Unable to find the wrapper "https" - did you forget to enable it when you configured PHP? in /test.php OpenSSL and OpenSSL-devel are installed, and PHP is also configured with cURL support for SSL connections. See: http://i.imgur.com/ExAIf.png Any idea what might be going wrong? Further info: CentOS 5.8(64) with Nginx 1.2.4

  Read the article

• Colocation and HSRP setup

  - by WinkyWolly

  My colocation provider has setup HSRP for us and has provided us 2 drops (plugged into 1/1/1 and 1/1/2) from their routers as well as a /29 with 2 HSRP IP's and the rest of the /29 usable for the switch. I know that HSRP should be pretty much plug and play as long as the ports are in the same VLAN. However I'm confused as to how to the IP setup should work. Currently I've assigned port 1/1/1 the full /29 however I think this is incorrect because if I were to unplug it port 1/1/2 wouldn't work as it has no IP assignment. What's the proper way to do this?

  Read the article

• Squid stale-while-revalidate not working when max-age=0

  - by Wiliam

  Squid 2.7 always reaches backend, expected is to reach backend using stale-while-revalidate only when cache expires, not when client triggers max-age=0. Script: <?php header('Cache-Control: public, max-age=10, stale-if-error=200, stale-while-revalidate=500'); header("Last-Modified: " . gmdate("D, d M Y H:i:s") . " GMT"); sleep(2); die("OK"); And squid config: # http_port public_ip:port accel defaultsite= default hostname, if not provided http_port 80 accel defaultsite=mydomain.com # IP and port of your main application server (or multiple) cache_peer 127.0.0.1 parent 8000 0 no-query allow-miss originserver name=main # Do not tell the world that which squid version we're running httpd_suppress_version_string on # Remove the Caching Control header for upstream servers header_access Cache-Control deny all #header_access Last-Modified deny all # log all incoming traffic in Apache format logformat combined %>a %ui %un [%tl] "%rm %ru HTTP/%rv" %Hs %<st "%{Referer}>h" "%{User-Agent}>h" %Ss:%Sh access_log /usr/local/squid/var/logs/squid.log combined all cache_effective_user squid refresh_pattern . 10080 90% 999999 ignore-no-cache override-expire ignore-private icp_port 0

  Read the article

• how do I set up a virtual host (it's not working, and I've done everything right)

  - by piratepartypumpkin

  My router redirects port 80 to port 8080. My router works fine and my domain name is routed properly. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

  Read the article

• TCP connection between PCs in home wi-fi network

  - by Nordvind

  I want to establish a connection between 2 PCs. Point is to practice in writing client-server applications and similar stuff. I've heard around, that I can access another PC in network by address like "Router IP:port number". Am I right or i got it wrong? So how do I configure router to let connections to certain ports? And what would address look like, if I'm, say, connecting to 80 port on my home server? P.S. Will be grateful for links to some tutorials on this matter, if any.

  Read the article

• How to stop nginx on Mac OS 10.6.3

  - by Alex Kaushovik

  I've installed nginx server on my Mac from MacPorts: sudo port install nginx. Then I followed the recommendation from the port installation console and created the launchd startup item for nginx, then started the server. It works fine (after I renamed nginx.conf.example to nginx.conf and renamed mime.types.example to mime.types), but I couldn't stop it... I tried sudo nginx -s stop - this doesn't stop the server, I can still see "Welcome to nginx!" page in my browser on http://localhost, also I still see master and worker processes of nginx with ps -e | grep nginx. What is the best way to start/stop nginx on Mac? BTW, I've added "daemon off;" into nginx.conf - as recommended by various resources. Thank you.

  Read the article

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >