Search Results

Search found 9557 results on 383 pages for 'x86 64'.

Page 220/383 | < Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >

• Windows 7 on 1st Gen MacbookPro Unibody (Q4-2008) - power problems.

  - by typemismatch

  I have the first generation macbook pro, purchased Q4 2008. I've been trying to run Windows 7 and can get it all installed great with the BootCamp 3.1 64 bit drivers however ... power management isn't great. The screen and keyboard don't automatically dim - the laptop gets too hot. I noticed on some newer macbook pros that windows 7 works perfectly and the above doesn't happen. Does anyone know if there really is a hardware issue with this 1st gen or is there some firmware update I can use to fix this? Thanks!

  Read the article

• If a change the CPU, must I reinstall the OS?

  - by dag729

  Hi, as suggested by the title, I want to change CPU: actually I have two computers, one with Ubuntu running on an AMD Athlon 64 dual core 5200+ and the other with FreeBSD running on an AMD Sempron single core LE-1250. I would like to swap (I am not sure that this is the correct term...) the CPUs from one computer to the other one, that is take the dual core from the ubuntu pc and put it inside the freebsd pc and viceversa. The mobo is the same. Do you think I will encounter problems?

  Read the article

• Windows doesn't recognise my USB key anymore (it used to work)

  - by dominicbri7

  I use my friend's USB flash drive (Corsair flash voyager 16gb) to transfer files from my laptop to my desktop computer. However, since a couple of days my laptop stopped recognizing the USB key.. while there is still no problems with all other computers. I use Windows 7 64 bits if that can help. I tried uninstalling the driver, rebooting and all those kind of tricks, but it won't work. When I connect it and open the "My computer" window, I see "Removable Disk (G:)" for a moment, then it disappears... then it reappears again and it keeps doing that periodically. I can't even right click then hit "Properties" because it disappears. As I recall, it DOES work on every other computers, I think it has to do with the driver but what can I do?

  Read the article

• Video has become blurred and smoothed out?!

  - by benwebdev

  Hi, Since yesterday video and graphics on my Windows 7 desktop seem to have become smoothed out and blurred slightly and I'm not sure why. The last thing I did on the machine was play Fallout New Vegas for the first time. An example can be seen in the picture here screenshot - note how smoothed out the character on the right seems, lots of definition looks lost. It's really annoying and happening regardless of what I watch. My system is below: Windows7 Ultimate 64 bit 6GB RAM Sapphire HD 5770 Vapor-X 1GB Gigabyte X58A-UD3R Motherboard Coolermaster Silent Pro M series 700W power supply All help greatly appreciated thanks

  Read the article

• full-screen browsing with IE10 on Windows 8

  - by Tom

  I have updated to Windows 8 and got Internet Explorer 10, but I don't get the full screen mode, is just like another desktop app. All links on the Windows Store Apps (Bing, News...) redirect to the old desktop and open my default browser (chrome). I have set IE as default browser but that not solve the problem. I have been looking on the IE10 options but I don't see this option. How can I solve this? Maybe this info help: Windows version: Windows 8 Pro 64 bits Installed Browsers: Firefox, Chrome (default), Opera, IE10 I have seem other people with the same version and is working Edit: Is possible to have IE10 by default for windows 8 apps links and Chrome for Desktop?

  Read the article

• full-screen browsing with IE10 on Windows 8

  - by Tom

  I have updated to Windows 8 and got Internet Explorer 10, but I don't get the full screen mode, is just like another desktop app. All links on the Windows Store Apps (Bing, News...) redirect to the old desktop and open my default browser. I have been looking on the IE10 options but I don't see this option. How can I solve this? Maybe this info help: Windows version: Windows 8 Pro 64 bits Installed Browsers: Firefox, Chrome (default), Opera, IE10 I have seem other people with the same version and is working

  Read the article

• Workaround broken sudo?

  - by perreal

  I managed to break sudo by deleting the libc.so.6 sym-link in /lib. I copied the actual file and created a symbolic link with the same name under my home directory by using LD_PRELOAD=/lib/libc-2.11.3.so. At this point, all binaries linking libc are working through preload except sudo. For sudo, I need to write (and don't know why): $ /lib/ld-linux-x86-64.so.2 --library-path . /usr/bin/sudo but this gives me: $ sudo: must be setuid root Checking the permissions: $ ls -l /usr/bin/sudo $ -rwsr-xr-x 2 root root 166120 So the setuid bit is actually set. Question: I need to create a symbolic link named /lib/libc.so.6 through my active ssh connection without using sudo, or, make sudo work somehow. I don't have the root password and I can't connect through ssh anymore. Is there any other way I can get authorization?

  Read the article

• mass deploy Oracle patches with OEM with different OS's

  - by bobsmith12

  I have not been able to get this to work. We are running our OEM grid control database/oms on Red Hat 5(32 bit), but our databases are on Solaris x86-64. I could not mass deploy agents since the Operating Systems were different. When I download patches it is by OS. Is there a way to mass deploy to multiple operating systems? I have alot of databases. I was given the redhat server for OEM because it was available. We are have 10.1,10.2, and 11.1 databases. OEM DB is 10.2.0.5

  Read the article

• Empty DVD Drive indicates it has music in it (CDFS)

  - by Amado Colberg

  I have a Windows 7, 64 bit computer with a Blu-ray DVD drive. When I first start the computer, the DVD drive indicates it has music in it, but it is empty. If I put a CD in it, it will not Autoplay. But, if I open the drive and close it again, it will Autoplay and will no longer act as if it has a music CD in it. I've checked the drive with Plextor Utilities and it says it is working OK. I would appreciate any help with this.

  Read the article

• Can't see CMD.EXE on Windows 7

  - by Andrea

  I have a problem with Windows 7 and cmd.exe with these conditions: Logon as non admin user Launch cmd.exe I can see cmd.exe in task manager but it's invisible in the desktop and I don't know what to do, everything is fine and I can see cmd.exe if I do login with an admin account. I can see it in the "Process" tab but not in the "Application" tab, and if I launch five cmd.exe's, I see five processes, but from that tab I have no "Bring to front" or "Maximise" I can't find any WOW folder under C:\Windows, even with show hidden and system files enabled. I'm running Windows 7 32-bit running on a 64-bit Intel Core 2 Duo E7500

  Read the article

• Laptop forgets second monitor when it goes to sleep

  - by al c

  I recently updated my nvidia driver... now I have to re-establish the connection to my second monitor everytime the laptop goes to sleep. When I open the NVIDIA control panel, the second monitor is listed there but the checkbox beside it has been cleared. Oddly my laptop screen is identified as display #3 and the external screen as display #4. Is there a registry key that I can clear to get them set back to #1 & #2? Will that fix the problem? Or is there a simpler solution. (It's a Dell Studio XPS laptop with GeForce 9500M running Windows Vista 64-bit) TIA Al

  Read the article

• Manually Add the TortoiseSVN Registry information?

  - by Pete Michaud

  I recently installed TortoiseSVN on my Windows 7 64 bit computer. For reasons outside the scope of this question, the installer could not get appropriate permissions to add the keys that TSVN needs in the registry. I'd like to add those keys manually, with a reg file. I tried unzipping the .msi installer to see if the .reg file was there, but no luck. I looked around the net a little, but no luck. I looked in the source code, figuring there must be a file in there somewhere with a list of all the registry changes in one place, but I haven't found any such thing. How can I get a complete list of registry changes for a fresh TortoiseSVN installation?

  Read the article

• Is virtual machine slower than the underlying physical machine?

  - by Michal Illich

  This question is quite general, but most specifically I'm interested in knowing if virtual machine running Ubuntu Enterprise Cloud will be any slower than the same physical machine without any virtualization. How much (1%, 5%, 10%)? Did anyone measure performance difference of web server or db server (virtual VS physical)? If it depends on configuration, let's imagine two quad core processors, 12 GB of memory and a bunch of SSD disks, running 64-bit ubuntu enterprise server. On top of that, just 1 virtual machine allowed to use all resources available.

  Read the article

• Cherokee high virtual memory usage even after disabling I/O Cache

  - by nidheeshdas

  hi all I've Ubuntu 10.04LTS 64-bit running on a openvz container and Cherokee 1.0.8 compiled from source. The virtual memory usage of cherokee-worker is around 430 MB even after disabling I/O cache from Advanced - I/O Cache - NOT enabled. Is this issue particular to openvz? Because many people reported to have successfully reduced virt memory usage by disabling io cache. htop output: http://imgur.com/z5JEL.jpg (newbies not allowed to post image.) thanks in advance. nidheeshdas

  Read the article

• Clarification of the difference between PCI memory addressing and I/O addressing?

  - by KevinM

  Could someone please clarify the difference between memory and I/O addresses on the PCI/PCIe bus? I understand that I/O addresses are 32-bit, limited to the range 0 to 4GB, and do not map onto system memory (RAM), and that memory addresses are either 32-bit or 64-bit. I get the impression that memory addressing must map onto available RAM, is this true? That if a PCI device wishes to transfer data to a memory address, that address must exist in actual system RAM (and is allocated during PCI configuration) and not virtual memory. So if a PCI device only needs to transfer a small amount of data at a time, where there is no advantage to putting it into RAM or using DMA, then I/O addressing is fine (e.g. a parallel port implemented on a PCI card). And why do I keep reading that PCI/PCIe I/O addressing is being deprecated in favour of memory addressing? Thanks!

  Read the article

• Installation fails after period of time

  - by Jack Marchetti

  I'm running Windows 7 64 bit, Ultimate. I'm running into a problem where, if my computer is on long enough, I am unable to install any software. For example, if I reboot and try to install something, for the most part, it will succeed. if I try and install something after a few hours/days, it will always fail. Sometimes stating that "a previous install failed..." or "an install is already taking place..." even though there is nothing being installed. This also seems to be making my Windows updates fail at a pretty regular rate. Any ideas?

  Read the article

• VPC on Windows 7 very slow network

  - by Shigg

  I have a Windows 2003 virtual machine which I use for website testing. I've just installed Windows 7 and am using the new version VPC (not xp mode). When I try to copy a file - I need to copy some big databases across - I get a file copy speed of about 20k per sec. Copying from one PC to another on the real network transfers files at 13mb per second. Any ideas what may be causing this? I've turned off differential network compression on win 7. The Virtual HD is on a seperate physical drive to the OS. Running Windows 7 64 bit on a dual xeon with 16gb ram and 10,000 rpm drives. Tried installing VPC 2007 but windows blocks it running saying its not compatable. Many thanks for any ideas.

  Read the article

• Multi-monitor resolution and position settings lost after reboot

  - by SoftDeveloper

  I've had two 1280x1024 monitors running for years on an nVidia 8800GT card with no problems. I've now replaced one monitor with a new 2560x1440 one. The card seems to support both fine, however every time I reboot the resolutions and monitor positions revert to the old settings. I've tried upgrading, downgrading, stripping out and reinstalling many versions of the nvidia drivers to no avail. Logging in as another user doesn't help - same problem. Booting into another another OS (Win7 64) works OK, so it is just this OS installation. During boot up everything looks fine (ie native 2450x1440 res) until the nVidia control panel or something is loaded which flips it back into the old mode. I have no old saved nvidia profiles. I can't find anything in the registry relating to these old settings. Its driving me crazy having to set resolutions and realign monitors on every reboot! Can anybody help?

  Read the article

• time on files differ by 1 sec. FAIL Robocopy sync

  - by csmba

  I am trying to use Robocopy to sync (/IMG) a folder on my PC and a shared network drive. The problem is that the file attributes differ by 1 sec on both locations (creation,modified and access). So every time I run robocopy, it syncs the file again... BTW, problem is the same if I delete the target file and robocopy it from new... still, new file has 1 sec different properties. Env Details: Source: Win 7 64 bit Target: WD My Book World Edition NAS 1TB which takes its time from online NTP pool.ntp.org (I don't know if file system is FAT or not)

  Read the article

• How to move a windows machine properly from RAID 1 to raid 10? [migrated]

  - by goober

  Goal I would like to add two more hard drives to my current RAID 1 setup and create a RAID 0 setup on top of the two RAID 1 setups (which I believe is referred to as "RAID 10"). Components Involved Intel P68 Chipset Motherboard 4 SATA ports that can be configured for Raid An intel SSD cache that sits in front of the RAID, and a 64 GB SSD configured in that manner Two 1TB HDDs configured in RAID 1 OS: Windows 7 Professional Resources Consulted so far I found a great resource on LinuxQuestions.org for a good "best practices" process for Linux machines, but I'd like to develop a similar process that I know works on Windows Machines.

  Read the article

• Why does Resource Monitor in windows 7 show half my memory as "Hardware Reserved"?

  - by Brandon

  Does anyone know why in Windows 7 Resource Monitor shows that I have 8 GB of RAM installed on my computer, but I only have 3.2 GB available as 4.8 GB are in "Hardware Reserve". I researched this issue and tried going into msconfig and making sure that in the boot options the number of processors and max memory options were turned off. I also opened the computer up and reseated each of the memory sticks while clearing out any dust that was in there. Some info on the system I am using: OS: Windows 7 Enterprise 64-bit Edition CPU: AMD Phenom X4 9750 Memory: 4 X 2GB DDR2 memory Motherboard: MS-7548 (Aspen) Any help would be much appreciated.

  Read the article

• How can I modify the BAT file in this post so it will randomly select 1 background contained in a folder containing multiple backgrounds?

  - by Radical924

  Is there a way to modify the bat file from this post here: How do I set the desktop background on Windows from a script? so that it will randomly select 1 background image from a folder containing multiple images??? AND I would also like the background to randomly change to one of the backgrounds randomly contained in the same folder. If this is possible how would I modify the bat file below??? @echo off reg add "hkcu\control panel\desktop" /v wallpaper /t REG_SZ /d "" /f reg add "hkcu\control panel\desktop" /v wallpaper /t REG_SZ /d "C:\[LOCATION OF WALLPAPER HERE]" /f reg delete "hkcu\Software\Microsoft\Internet Explorer\Desktop\General" /v WallpaperStyle /f reg add "hkcu\control panel\desktop" /v WallpaperStyle /t REG_SZ /d 2 /f RUNDLL32.EXE user32.dll,UpdatePerUserSystemParameters exit Also I noticed that this bat file won't work usually (9 times out of 10)... I receive an "ERROR: The system was unable to find the specified registry key or value." I have Windows 7 64-BIT Home Premium Service Pack 1

  Read the article

• How to increase the disk cache of Windows 7

  - by Mark Christiaens

  Under Windows 7 (64 bit), I'm reading through 9000 moderately sized files. In total, there is more than 200 MB of data. Using Java (JDK 1.6.21) I'm iterating over the files. The first 1400 or so go at full speed but then speed drops off to 4ms per file. It turns out that the main cost is incurred simply by opening the files. I'm opening the files using new FileInputStream (and of course closing them in time to avoid file leaks). After some investigating, I see that Windows' disk cache is using only 100 MB or so of RAM although I have 8 GiB available. I've tried increasing the cache size using the CacheSet tool but any values I provide are considered out of range. I've also tried enabling the LargeSystemCache registry key but (after rebooting) the CacheSet tool still indicates I'm using 100 MB of cache (and doesn't increase during the test run). Does anybody have any suggestions to "encourage" Windows 7 to cache my 9000 files?

  Read the article

• What protocols will/are ISPs use for IPv6 deployment?

  - by rbeede

  Currently ISPs deal out addresses via DHCP for IPv4 dynamic (single) addresses. What protocol will/are ISPs going to use for IPv6 when they can hand a customer an entire /64 (or /48 if they are nice) block? DHCPv6, RA? For ISPs that support true end-to-end IPv6 will they provide gateway devices (similar to cable modem or true DSL bridges for example) that receive border information for that specific customer? I'm just trying to get an idea of how your common residential service customer will have to configure things in an IPv6 Internet (whenever that comes). Will it be something customers are expected to statically configure on their home wireless router? Today with IPv4 I do it like this: Modem (bridge) passes public IPv4 obtained via DHCPv4 from ISP to second device (wireless router). It in turn has its own DHCPv4 service it provides on the internal lan.

  Read the article

• What's better for deploying a website + DB on EC2: 2 small VM or a large one?

  - by devguy

  I'm planning the deployment of a mid-sized website with a SQL Server Standard DB. I've chosen Amazon EC2 to deploy it. I now have to choose between these 2 options: 1) get 2 small instances (1 core each, 1.7 GB of ram each): one for the IIS front-end, one for running the DB. Note: these "small instances" can only run the 32-bit version of Win2008 Server 2) a single large instance (4 cores, 7.5 gb of ram) where I'd install both IIS and the SQL Server. Note: this large instance can only run the 64-bit version of Win2008 Server What's better in terms on performance, scalability, ease of management (launch up a new instance while I backup the principal instance) etc. All suggestions and points of view are welcome!

  Read the article

< Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >