Search Results

Search found 8782 results on 352 pages for 'krishnadas pc'.

Page 221/352 | < Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >

  • homegroup administrator user no longer exists

    - by Beninja
    I had a PC with windows 7 that was the homegroup administrator for my network. I recently upgraded to windows 8 I went to homegroup in control panel and saw that the original homegroup was never removed. It says to talk to the administrator on and obtain the password to join the homegroup. I need to create a new homegroup but I cant unless I somehow remove the old one. And I cant do that because the user that had rights to the old one no longer exists. Please help!! Ben

    Read the article

  • Weird routing problems with VPN

    - by Borek
    In our VPN setup I have to add a route to my routing table like this: route add 1.2.3.0 mask 255.255.255.0 172.16.1.1 -p Our internal addresses 1.2.3.x then use 172.16.1.1 as their gateway and both my local internet and work VPN can work at the same time. However, when I disconnect from VPN and reconnect again, I can't ping our servers even though the connection status is "Connected". When I do route print my previously added route is listed but it doesn't seem to work. So I try to execute that 'route add' command again and as expected, it tells me that The route addition failed: The object already exists. But - and that's the point - when I now try to ping our servers again, everything works! So every time, I have to execute this route add command that will fail but fix the issue at the same time. Any ideas what I might be doing wrong? My PC is Windows 7 x64, I am Administrator, UAC is enabled and the command prompt is run with elevated privileges.

    Read the article

  • Are speakers wasting power when they are not in use?

    - by Dennis Cheung
    I guess all of you have a pair/set of speakers for your MP3s. I am just interesting to how do they do when they are not playing? How actually the power spent by the speaker? Does any the below cases matter? Idle / Silence input When you computer is off / not connected Raise the volume by hardware (turn/push the button on the speaker) Raise the volume by software (do it with your mouse) BTW, to save the world. I am here to suggest you to unplug it when you leave your PC.

    Read the article

  • Skydrive does not synchronize with one device but synchronizes successfully with another one.

    - by Hobbes
    I have an Outlook id. I also have Skydrive installed on my personal laptop (Windows 7 x64). The folders and files synchronize successfully. Today, I installed Skydrive on my office PC and logged in with the same id as above but it does not synchronize any of my folders or files, other than the default ones. When I view the logs (filename: SkyDrive.exe.reg.2012-08-09-150239.654.log), I see the following entry. 09-17-12,13:31:35.075,45a,146c,0,PAL,systeminformationhelper.cpp(661),0,0018E4F8,CRIT,The registry key to block Remote Access is not found.,System Error Code=0x2 Any idea as to what could be the problem?

    Read the article

  • Ubuntu web site hosting & free ,tk domain

    - by user5819
    Hello, I am sort of new to web hosting so sorry if I ask bad questions. I have a pc that runs ubuntu I instaled apache and now I host a web site, but I need a domain name so I found out .tk is free. The site works when typing 192.168.1.x in the browser(x= a number) but in dot.tk when I register in ip it whats one that look like 79.117.x.x so thats where I get stuck, I think I managed to make my ip address static but it still looks like 192.168.1.x and I can't put that in because it says: " This IP address is not valid". Why must it have the ip address that looks like 79.117.x.x and won't work with the internal static one and how can I do to host my site with a .tk domain name ? PS: I'm using a cisco router that's connected with computer via a cable.

    Read the article

  • Blinking motherboard power LED

    - by Corey D
    I was just rebuilding an old desktop PC to be used as a HTPC and the LED on the motherboard that indicates when there is power is blinking fairly rapidly. The only way I can get the machine to boot is to press the power button immediately after plugging it in, and even then I cannot make it into the BIOS. The power supply has more than enough juice to power all of the components, and is from a reputable manufacturer. The motherboard is an Asus and is about 4.5 years old. Is my power supply hosed? Or is it my motherboard?

    Read the article

  • Sharing a printer over the net from Windows 7 to Windows Server 2003

    - by Grant Unwin
    Hi, I need to share a printer that is connected to a Windows 7 computer. The windows 7 computer is in another building about an hours drive away. The computer that needs to access the printer is running Windows Server 2008. Ive tried setting the printer as 'shared' for 'everyone' on the Windows 7 PC and accessing it from the server by adding a TCP/IP port to the IP address but the printer just wont add. From googling aparently it may need setting up as a printer server through IIS, but i'm just not sure on the best practice. Any help greatly appreciated. Thanks Grant Unwin

    Read the article

  • Cloning Windows 7 installation from MBR to GPR drive and make it bootable

    - by Nelluk
    I've seen threads on similar topics - such as this one - but the answers never seem to solve how to make it bootable. I have Win 7 64-bit on a PC installed on a 2tb MBR volume. The motherboard is UEFI compatible. I just installed a secondary internal 3TB drive which will be partitioned as GPT. Is there a relatively easy way to clone my installation over to the new drive and have that drive be bootable? I have used EaseUS Partition Master to clone the C volume to the D volume, but that would not boot and I assume the issue is that one is MBR and one is GPT. Is there a process to do this?

    Read the article

  • acessing a subnetwork from within a vm

    - by yan bellavance
    I have a pc running windows 7. I have vmwareplayer running RHEL5 I have 1 physical ethernet connection. this ethernet connection is wired to a hub. there is another device on that hub that needs to be in a certain subnetwork (192.168.0.xxx)(lets call him device X) but the general network is 192.168.1.xxx How can I configure the network adapters so that I can ping device X from RHEL5 in the vm. Originally I could ping google from both windows and rhel (I was in the .1 network) but not device X since he is on a different subnetwork address. Now that I have put it on the .0 I can ping device X from windows but not from rhel5 and cannot access the web. I did this by manually setting the IP address.

    Read the article

  • Where can I download copies of a Windows XP ISO image with Internet Explorer 6 or Internet Explorer 7 for VirtualBox?

    - by Andrew Arrow
    I have Windows 7 Professional hosting Ubuntu inside VirtualBox for my development machine. To test my site, I run Internet Explorer and hit my Ubuntu box. This works great for Internet Explorer 8, the default browser on this Windows machine. I also want to run another VM with a copy of Windows XP with Internet Explorer 6 or Internet Explorer 7. Where can I download ISO image files of old copies of Windows XP? I've looked in Internet Explorer Application Compatibility VPC Image and these only run in Virtual PC/XP Mode which won't run while VirtualBox is running. If I have to run VirtualBox (can't work without Ubuntu running the site), is there any way to test Internet Explorer 6, Internet Explorer 7, and Internet Explorer 8 from the same Windows 7 machine?

    Read the article

  • Programs minimized for long time takes long time to "wake up"

    - by bart
    I'm working in Photoshop CS6 and multiple browsers a lot. I'm not using them all at once, so sometimes some applications are minimized to taskbar for hours or days. The problem is, when I try to maximize them from the taskbar - it sometimes takes longer than starting them! Especially Photoshop feels really weird for many seconds after finally showing up, it's slow, unresponsive and even sometimes totally freezes for minute or two. It's not a hardware problem as it's been like that since always on all on my PCs. Would I also notice it after upgrading my HDD to SDD and adding RAM (my main PC holds 4 GB currently)? Could guys with powerful pcs / macs tell me - does it also happen to you? I guess OSes somehow "focus" on active software and move all the resources away from the ones that run, but are not used. Is it possible to somehow set RAM / CPU / HDD priorities or something, for let's say, Photoshop, so it won't slow down after long period of inactivity?

    Read the article

  • Unable to make my bios see my sata hdd

    - by Stefan
    I know there are many question about that, but I tried everything and I'm still not able to make my bios see my sata2 hdd. I've got a QDI motherbord with no sata port; only 2 ide ports. I had an old ide hdd, now i've removed it and bought a sata2 hdd. Since my pc has no sata slots i bouth a ide-to-sata adapter. So, i don't have any os installed on the new drive, and the old drive is removed. My problem is that I'm unable to see my hdd on bios. I suppose that my bios, since it's an old version, doesn't have sata drivers, but I don't know if I must install it and also I dont know how to do it. Anyone can help me?

    Read the article

  • How to install Windows 7 From Network?

    - by George
    Hello SuperUser My question is that is it possible to install Windows 7 (Current RTM Version) on a computer without using removable media like DVD or USB. First thing that comes to my mind is network but i dont have experience of doing Fresh Install of Windows 7 via Network. How to install Windows 7 via network without any removable media? P.S. I know some may think that doing so, is just a waste of time and it's easier to do it with removable media, but in current situation the target PC neather has CD/DVD Drive nor supports booting from USB. And in addition to that, Target computer is connected to Network via Wireless Network (Dunno if it will make any problem with installation).

    Read the article

  • dialup connection script

    - by BParker
    I've just started working for a company who produce a specialist modem. In the test department they simulate actual use with a bunch of pc's acting as clients connecting over this modem. As such each needs to dial a set of dial-up connections. Each of these has to be created manually, and currently takes quite a while on each machine, so i was hoping to be able to automate the creation process. Back in the early days of the internet i remember getting CD's from ISP's where the dial-up connection was configured automatically, and i was wondering if anyone lknew how to do this, or if they could point me in the direction of a tutorial about it. To be clear, i don't want to automate actually dialing the connection, but i do want to run a script which creates the icons in the networking applet that allows us to dial these connection. Thanks in advance!!!

    Read the article

  • Can't play blu ray on sony vaio fz

    - by user19455
    Hi. I have a Sony Vaio FZ (VGN-FZ31M) with a blu ray drive. I have just recently purchased the 2001 Space Odissey in blu ray but haven't been able to play on my laptop. When I try to play it with WMP i get this: "Windows Media Player cannot play the DVD. The disc was created in a manner that the Player does not support." and this with VLC: "VLC cannot open MRL. Check log for details." I have once formatted the pc and done a clean install without the sony vaio recovery cd. Is it possible that it is necessary a specific blu ray driver that I have not installed? Thanks.

    Read the article

  • Mac Air Bootcamp Windows 7 Installation and USB3 Hurdles

    - by Casey
    I am trying to load windows 7 on a new Mac Air(OS X 10.9 Mavericks) using Boot camp, a downloaded windows 7 iso file, and USB3 flash drive. No obvious issues with stepping through the initial phases of boot camp and disc partition, but when the system reboots to load windows setup/install from the USB3 flash, it stalls after a few screens and gives a "missing cd/dvd drive" error. I have read similar posts regarding this fail that imply there is possibly a windows 7 compatibility concern with USB3, and that if a USB2 port is available....or if you can change your BIOS to make your USB3 look like USB2...then you can get around this error. Unfortunately I only have USB3 ports on this system, and it appears accessing the PC equivalent "BIOS" on the new Macs is very difficult....and if you screw it up you can ruin the system. Does anyone have any suggestions? I should also mention that there is NOT a CD/DVD drive on the Mac Air....and I can't migrate to Windows8 (for various reasons). Any help is much appreciated!!

    Read the article

  • Bind: dns not 'spreaded'

    - by realtebo
    I've elfoip.net with bind $ whois elfoip.net | grep 'Name Server' Name Server: NS.ELFOIP.NET I need elfoip.net be able to serve third levels domain, like mickymouse.elfoip.net, etc... Yes, I'm trying to create an other useless dyndns clone. i've added some third level as A RR. Eg: executing this from the server itself $ dig @localhost mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 I was expecting in one or two days, from my pc i can digit in browser mattinauno.elfoip.net and get page a 192.81.221.113 But this is not happening. Are there any prerequisites to satisfy to allow dns of my isp to be able to forward dns resolution of *.elfoip.net to MY dns ? (Or to ask to him and then cache ?) TTL of zone is set a 5m I've not AllowQuey directive, is it necessary for other dns to cache from mine ? I've cheched the zone with bind utility named-checkzone but no error detected. How to diagnose why other dns doesn't take in account RR from mine ? from my home pc dig @ns.elfoip.net mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 ;; AUTHORITY SECTION: elfoip.net. 300 IN NS ns.elfoip.net. but dig @8.8.8.8 mattinauno.elfoip.net give no answers Whole zone file: note I've used nsupdate, so this file has been re-edited and re-formatted from this utility ! root@mirko:/var/named# cat elfoip.net.db $ORIGIN . $TTL 300 ; 5 minutes elfoip.net IN SOA ns.elfoip.net. hostmaster.elfoip.net. ( 2013062314 ; serial 3600 ; refresh (1 hour) 600 ; retry (10 minutes) 86400 ; expire (1 day) 60 ; minimum (1 minute) ) NS ns.elfoip.net. A 109.168.99.6 $ORIGIN elfoip.net. $TTL 60 ; 1 minute google A 173.194.35.56 maiscai A 192.81.221.113 mattinadue A 192.81.221.113 mattinauno A 192.81.221.113 $TTL 300 ; 5 minutes ns A 109.168.99.6 $TTL 60 ; 1 minute prova A 208.67.222.222 prova2 A 13.23.34.45 A 13.23.34.46 www CNAME elfoip.net. EDIT: added named.conf.local zone "elfoip.net" { type master; // file "/etc/bind/elfoip.net.db"; file "/var/named/elfoip.net.db"; allow-update { key elfoip.net ; }; }; EDIT: I've no setup list-on directive *EDIT Added a TCPDUMP after [email protected] wwww.elfoip.net from a machine which uses my company internal dns, who allow recursive query. root@mirko:~# tcpdump -i eth0 'port 53' tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 11:57:23.293611 IP host9-210-static.22-87-b.business.telecomitalia.it.45958 > mirko.elfoip.net.domain: 61337+ A? www.elfoip.net. (32) 11:57:23.294114 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.45958: 61337* 2/1/1 CNAME elfoip.net., A 109.168.99.6 (95) 11:57:23.294554 IP mirko.elfoip.net.59571 > google-public-dns-a.google.com.domain: 45851+ PTR? 9.210.22.87.in-addr.arpa. (42) 11:57:23.330444 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.59571: 45851 1/0/0 PTR host9-210-static.22-87-b.business.telecomitalia.it. (106) 11:57:23.331181 IP mirko.elfoip.net.44171 > google-public-dns-a.google.com.domain: 33339+ PTR? 8.8.8.8.in-addr.arpa. (38) 11:57:23.439405 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.44171: 33339 1/0/0 PTR google-public-dns-a.google.com. (82) 11:57:31.350654 IP host9-210-static.22-87-b.business.telecomitalia.it.30108 > mirko.elfoip.net.domain: 38269 [1au] A? ns.elfoip.net. (42) 11:57:31.351117 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.30108: 38269* 1/1/1 A 109.168.99.6 (72) If i dig @8.8.8.8 www.elfoip.net, NOTHING happens in dump log !

    Read the article

  • WPA Enterprise Wireless Bridge

    - by prestomation
    I live in college housing at a university with wifi available. unfortunately, my bedroom(where I'd like to place my PC) gets little to no reception. I'd like to place a router in the strongest spot and rebroadcast. I understand this can be done with DD-WRT/etc, but this particular network is WPA Enterprise with my own personal username/password. I can't find any concrete evidence that I can get my router to act as a repeater for this encryption. I don't currently have a router to test it on, otherwise this would be easy, I just don't want to buy a router if it will be worthless to me. Thanks for your help

    Read the article

  • Power supply surges detected during previous power on

    - by Blastcore
    Message is this: "Power supply surges detected during previous power on" "ASUS Auto-Surge was triggered to protect system from unstable power supply" When i went to sleep yesterday and woke up, when i moved the mouse to go back from screen saver, it didn't do anything. So i left it, i came back from class and got this issue. (I didn't restart before going to class... So the screen was left like it was) Today there was a power cut in half of my house. (Computer is on the side that it didn't cut...) Voltages are fine, like always. How do i remove message? It's just maybe sensor glitch? Even disabling the Anti-Surge my PC "shuts down" (Only monitor, but maybe components do too.)

    Read the article

  • Why is systemd not setting my system time?

    - by Alex Chamberlain
    I'm running Arch Linux. Recently, when I turn on my PC, the system time is set to 1:00 1 January 1970 - presumably the 1:00 o'clock is from the timezone shift. Does anyone have any ideas why systemd isn't setting my system time correctly? Some useful output (I think)... [root@alex-desktop network.d]# timedatectl status Local time: Sun 2013-06-09 16:33:04 BST Universal time: Sun 2013-06-09 15:33:04 UTC RTC time: Sun 2013-06-09 15:18:50 Timezone: Europe/London (BST, +0100) NTP enabled: yes NTP synchronized: no RTC in local TZ: no DST active: yes Last DST change: DST began at Sun 2013-03-31 00:59:59 GMT Sun 2013-03-31 02:00:00 BST Next DST change: DST ends (the clock jumps one hour backwards) at Sun 2013-10-27 01:59:59 BST Sun 2013-10-27 01:00:00 GMT

    Read the article

  • Set Display Refresh Rate in OSX w/o External Utilities

    - by codedonut
    I have an iMac and an LG Flatron connected as a secondary monitor. The recommended resolution for the flatron is 1680x1050 @ 65.290 Hz (horiz), 59.954 Hz (vert). For some reason, OSX is choosing a slightly different set of scan rates and this is currently my best guess of why the monitor goes into power saving mode when connected to the iMac (but works fine on a PC). Now, I resolved this by installing switchResX and fudging the scan rates according to the specs in the manual. But how does one change these rates w/o 3rd party tools? Which config files need editing? Thanks

    Read the article

  • Mac claims to have connected to wireless network, but hasn't

    - by Mick
    I am attempting to connect a new mac OSX 10.6.5 laptop to a wireless network (I am a windows expert but a mac novice). It used to connect without problem to the network when I had the security set to "64 bit wep". Now I have changed the security on my belkin router to "WPA-PSK (no server)". I have two PC's and an old mac connecting via the new security setting without problem. Now I have the problem that on the new mac, the wireless icon is indicating a good connection (5 dark bars). Also the network name has a tick next to it on the wireless drop down menu. But I can not view any websites. I can not even connect to the router by typing 192.168.2.1 into a browser address bar. Any ideas where I went wrong?

    Read the article

  • Ghost Image - windows asks for activation on when deployed to VM

    - by Chris Sobolewski
    I have several images created with Ghost Solution Suite (v11 I believe), the images have been in use for a few years now, but I am finally to the point where I have enough time to attempt to virtualize them for easier updates. I am running VMWare and attempting to image the virtual machines with my ghost image files. For my images I am running sysprep with minisetup and using reseal. The image deploys successfully, however when I start the VM for the first time, it demands windows activation. This doesn't happen when I image a physical computer, even a different model with different hardware. The idea of virtualizing my images becomes rather worthless if I am unable to deploy the images without having to activate every time (especially as Microsoft keeps declaring our volume licence key as invalid for activations). Does anyone know why it is asking for activation on a virtual machine, but not a physical PC? How can I prevent this?

    Read the article

  • NAS disk - problem with accessing SAMBA

    - by dominolog
    Hello I have a NAS disk running on some version of Linux. The disk is located in local network (5 PC running XP or Vista, all connected to Linksys Router). I have problems accessing NAS resources through SAMBA. The 1st issue is that the NAS is not accessible through hostname (even if it is configured), 2nd point is that it is mostly not accessible through IP manner (\IP_OF_NAS). Rest of services (FTP, HTTP access) works flawlessly. I connected the NAS to my home network (only 1 WinXP and Linsys router) and the NAS is working fine - SAMBA access together with hostname recognition works perfectly. I wonder this is an issue with WINS? Could anybody help? Regards

    Read the article

  • qtcreator keyboard problem: azerty/qwerty

    - by Allen
    I picked up the qt SDK and I've been trying it out. I'm working in English but I have a French AZERTY keyboard. When I run Qt Designer all is fine. When I run Qt Creator or Qt Designer from within Qt Creator things work as though I had a QWERTY keyboard, so I have to hit the "q" key to get an "a", etc. Qt Creator is version 1.3.1 and it is using Qt 4.6.2. My PC is running XP. What is going on and what is to be done? Any ideas? Editing a program in this setup is, of course, impossible! Luckily I discovered I can use an external editor, so I can use xemacs, which would be my first choice anyway, but this keyboard problem is a real nuisance! Thanks.

    Read the article

< Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >