Search Results

Search found 8185 results on 328 pages for 'capture card'.

Page 225/328 | < Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >

• Computer won't start unless power is removed for ~5 minutes

  - by Paul Tarjan

  I have a fairly standard 2-year old desktop computer (quad-core intel, single hard drive, decent video card, 300W power supply) which recently started acting up. I'm not sure what the cause is, so hopefully you can help. Sometimes (once a week-ish) I press the power button and nothing happens. No blinking, no sounds, no nothing. If I remove the power cord (or flip the switch on the power supply) I hear a capacitor discharge. If I leave it in the "no power at all" state for about 5 minutes then I can put the plug back in and the computer works perfectly. What is the issue? What do you think I have to replace?

  Read the article

• How to Use 3 Monitors

  - by The.Anti.9

  Right now my setup has a nice big 24" flatscreen in the center, and a 19" flatscreen to the left. And a big gaping hole on the right. I have a 3rd monitor to put there, but I'm not sure how to get the computer to recognize it. Do I need a graphics card with 3 ports? Or can I span the monitors over non SLI-Linked graphics cards? Is it possible to plug my 3rd monitor into the on-board VGA port and have it work?

  Read the article

• Best motherboard power supply combo for backblaze server

  - by jin14

  Building a backblaze server as described in this article. http://blog.backblaze.com/ So 45 hard drives in one box. I'm making it a MSDPM 2010 server so I actually don't even need raid cards in there as MSDPM will figure out how to use all of the hard drives on it's own. So need to know what motherboard, CPU, power supply I should get. Primary hard drive : SSD 128GB Storage : 45 1.5GB sata drives OS : windows 2008 Backup software : Microsoft System center Data protection server 2010 Need to know Which mother board to buy which will support 45 SATA hard drives. Don't need a raid card. Which power supply can power all 45 hard drives, 1 ssd drive, motherboard. Best set of equipment that meets my needs wins

  Read the article

• Screen tearing with GeForce 550 Ti

  - by Konair0s

  Recently I switched to the new monitor and graphic card - DELL U2312HM and GeForce GTX 550 Ti. I have problems with screen tearing (like in this picture from Wikipedia). Usually it is somewhere in upper part of the screen. Mainly happens in videos (in flash videos tearing heavier). In games all fine, except in-game videos (sometimes even videos built on game engine), but gameplay itself is clear, even in very fast actions. Connection with DVI. Problems both in Linux (Debian GNU/Linux, openSUSE 12.1, Linux Mint 13) and Windows (Windows XP, Windows 7), with various driver versions. 1920x1080, 60Mhz. How can I resolve this?

  Read the article

• Suggestions for wireless adapter

  - by Michael Kniskern

  I recently purchased a desktop computer and it did not come with a wireless network card. I am currently using the Belkin Wireless G USB Adapter and it is a very sub par product. It has very slow response times and download speeds with just basic browsing and downloads podcasts through iTunes. Does anyone have a better suggestion for a wireless adapter? Should I go with another USB adapter or one that connects directly into the motherboard? I am current using Windows Vista 64 bit Home Premium.

  Read the article

• No HDMI audio - Windows 8 - ASUS H81M-PLUS

  - by Paul Wright

  I have an issue with HDMI audio on Windows 8 using an ASUS H81M-PLUS motherboard (without an external GFX card). There are many forum posts advising you to go into playback devices and setting HDMI to be default - I have done this. To eliminate what works and what doesn't work: I have not been able to get sound from my HDTV using HDMI. I have used this HDMI cable with my PS3, so this cable should be fine. I am able to use the HDMI cable in extended mode, so that I have two monitors (including the TV), just no audio. This HDMI cable goes straight from the motherboard to the TV. Below I have included 'Device manager', and 'Playback Devices' (Sound). Device Manager Playback Devices, showing disabled and disconnected devices I am at a loss. I have uninstalled all drivers, and then rebooted and made windows look for the correct ones, made sure the HDMI device was default. Thanks, Paul

  Read the article

• Samsung syncmaster SA300

  - by lee

  I recently bought the above moniter. i am now using the DVI port in the moniter but the picture quality stil seems average like the same when i was using the VGA port. THere hasnt been a noticeable change. I am using the DVI output from my graphics card but i thought the picture quality should be alot more High Def than what it is. im just really disappointed in the out come as was expecting nearly High Def quality from my new moniter but just seems a bit normal. Could i need to change any settings?

  Read the article

• Virtual Machine Performance - More RAM or More Processor?

  - by webworm

  When looking to improve Virtual Machine performance what would be better ... Increasing the available RAM or increasing the processor power? Here is my choice ... Core 2 Duo @ 2.4 GHz with 8 GB RAM and integrated graphics (Mac Book Pro 13") Core i7 @ 2.6 GHz with 4 GB RAM and 512 MB dedicated graphics (Mac Book Pro 15") I plan to run Windows x64 in the VM with SQL Server 2008, Visual Studio 2010, and SharePoint 2010. I am planning to run VMWare Fusion v3. I also didn't know if a dedicated graphics card makes a difference when using a Virtual Machine. Thank you.

  Read the article

• getting started with SMS developement

  - by I__

  i will have the following set up: people will be sending text messages to a server, and that server will be forwarding the messages to other phone numbers i am not sure what kind of framework i should use. should i develop an SMS gateway and use AT commands? should i just try to somehow use AIM or GCHAT to capture and send SMS messages? would there be a different more suitable configuration? are there already developed frameworks that are free which i can use? for example i know that i can send an SMS to almost anyone through gchat or aim by sending a message to "+" and the number of the person. is this scalable and can i use it for my own benefit? any sms developers out there?

  Read the article

• Laptop VGA Output Stopped Working

  - by Jack7890

  I regularly use an external monitor with my laptop. Today, when I booted up, the external monitor refused to work--it just keeps going into power save mode. I tried a different external monitor and had the same problem, so it must be a problem with the laptop itself. Things I've tried: Going into the Display Settings via the Control Panel (I'm running Vista) and attaching/unattaching/reattaching the external monitor. Turning the computer off, unplugging, plugging it back in, and rebooting Blowing into the VGA out to get rid of any dust Toggling through the Fn+F7 options I'm thinking maybe this is an issue with my video card? If necessary, I'm comfortable opening up my laptop and playing around with things, but I'm not sure what to look for. Does anyone have any suggestions?

  Read the article

• Hiding monitor from windows, working with it from my app only [closed]

  - by Mikhail

  I need to use a monitor as a "private" device for my special application, I want to use it as a flashlight of a sort and draw special patterns on it in full screen. I don't want this monitor to be recognized by OS (Windows 7) as a monitor. I.e. user should not be able to move mouse to that monitor, or change its resolution, or run screensaver on it or whatever. But I want to be able to interact with it from my application. Monitor is plugged using an HDMI cable to a video card (most probably nVidia). What is the simplest way to do this? All solutions are appreciated, including purchasing additional adapters or simple video cards, or any other special devices.

  Read the article

• smallest footprint for Web Application server?

  - by edgardodelamanta

  There are times when you need to spare hardware resources (either to keep using legacy hardware, to play the embedded card, or just to be efficient because a large footprint is trashing CPU caches, leading to unacceptable levels of idle-states). In this spirit, some efforts have been made to make 'light' ports of Java or Mono (C# for Linux), and they range in the 80-50 MB (instead of the 100-200 MB). Add a Web server (Apache, IIS, etc.) to the scripting engine and you can happily dive into the GB (IIS + .Net) only to load the tool in memory. Anybody with more modest tools in the specs area?

  Read the article

• Laptop VGA Out Stopped Working

  - by Jack7890

  I regularly use an external monitor with my laptop. Today, when I booted up, the external monitor refused to work--it just keeps going into power save mode. I tried a different external monitor and had the same problem, so it must be a problem with the laptop itself. Things I've tried: Going into the Display Settings via the Control Panel (I'm running Vista) and attaching/unattaching/reattaching the external monitor. Turning the computer off, unplugging, plugging it back in, and rebooting Blowing into the VGA out to get rid of any dust Toggling through the Fn+F7 options I'm thinking maybe this is an issue with my video card? If necessary, I'm comfortable opening up my laptop and playing around with things, but I'm not sure what to look for. Does anyone have any suggestions?

  Read the article

• HP Proliant DL360 G5 + MSA50 RAID Setup recommendations

  - by JohnRB

  I am running a HP Proliant DL360 2 x 3GHz Xeon 16GB Ram P400 integrated RAID card with 6 x 73GB SAS HDDs running Ubuntu Server 14.04 CLI only. I recently got my hands on a MSA50 SAS Enclosure (10 x SAS HDD bays w/ SAS in/out interface) and wondering what you guys recommended as far as an addon raid controller for one of the pciex slots. I have both slots free Full and Half sizes. Any suggestions are greatly appreciated, I am an I.T. Consultant but have not used these particular units before so I was hoping to hear from someone who has. Thanks!

  Read the article

• "Verifying DMI Pool" hang caused by raid array..

  - by Ling

  Hi Experts, I have a problem, I obtained a new server with 4 hard drives (2 500 gig, 2 two TB), and an adeptec RAID card. I arranged them in two arrays with RAID 1 (500 gigs together as primary and the 2 TB drives for lots of data). When both arrays are configured, the server hangs while booting at message "Verifying DMI Pool", however if I remove the second array from the configuration the server boots fine. I have checked they are both on different channels, I have disabled all other peripherals from the boot menu and ensured the hard drive is #1. I have booted into the linux rescue mode and checked that it is reading both arrays fine. What else could be causing these problems? Thanks

  Read the article

• 912 stream processor available in OpenCL

  - by tugrul büyükisik

  I am thinking of assembling this system: AMD CPU (A8-3870 APU which has Radeon HD 6550D inside: 400 stream processors:xxx GFLOPS) nearly 110$ AMD Graphics card: HD 7750 (512 stream processors:819 GFLOPS peak performance) nearly 170$ Appropriate ram (1600MHz bus) Mainboard What GFLOPS level can I reach as a stable mode with using OpenCL and similar programs? Can I use all 912 stream processors at the same time? I am not trying to do a VS question. I need to know what could be better for scientific computing (%75 of the time) and gaming (%25 of the time) because I have a low budget. With "scientific calculations" I mean fluid dynamics/solid state physics simulating; with games I mean those that need openCL and PhysX.

  Read the article

• Netgear WNR1000 WiFi speed

  - by Kamil Klimek

  I have Netgear WNR1000 150N, Macbook Pro 13" with Broadcom BCM43xx 1.0, Network connection 60mbps When I connect through the cable I easily get around 60mbps. When I go through the WiFi it's capable to get only 32mbps at tops. Any ideas why is that? Is that my router limitation or maybe my WiFi card? If it is routers fault what router would you suggest. Best router would be with usb port for external hard drive. Forgot to add screenshot with connection details: Szybkosc transmisji == Transmission speed

  Read the article

• Searching Database by Arbitrary Date in PHP

  - by jverdi

  Suppose you have a messaging system built in PHP with a MySQL database backend, and you would like to support searching for messages using arbitrary date strings. The database includes a messages table, with a 'date_created' field represented as a datetime. Examples of the arbitrary date strings that would be accepted by the user should mirror those accepted by strtotime. For the following examples, searches performed on March 21, 2010: "January 26, 2009" would return all messages between 2009-01-26 00:00:00 and 2009-01-27 00:00:00 "March 8" would return all messages between 2010-03-08 00:00:00 and 2010-01-26 00:00:00 "Last week" would return all messages between 2010-03-14 00:00:00 and 2010-03-21 018:25:00 "2008" would return all messages between 2008-01-01 00:00:00 and 2008-12-31 00:00:00 I began working with date_parse, but the number of variables grew quickly. I wonder if I am re-inventing the wheel. Does anyone have a suggestion that would work either as a general solution or one that would capture most of the possible input strings?

  Read the article

• Unable to connect to network

  - by user33750

  Hey guys, I have a question. I have been having problems connecting a new netbook to my network at home. I have an Asus Eeepc 100HAB. I have tried to run a repair on the connection, uninstalled and re-installed the network card, made sure all of the drivers are up-to-date as well. Two caveats: I have a laptop that I recently switched to a wired connection because it wasn't connecting to the network as well, and the netbook connects to an unsecured network i found just fine, only having a problem getting into my home network. Passwords are correct, and the computer where the connection originates from is working fine as well. Any ideas?

  Read the article

• How to trigger a postback using JQuery Droppable plugin ?

  - by Sandeep K Ram

  Hi, This is my script for the draggable and droppable <script type="text/javascript"> $(function() { $(".Source li").draggable({ appendTo: "body", helper: "clone", revert: "invalid" }); $(".Destination ").droppable({ activeClass: "ui-state-default", hoverClass: "ui-state-hover", accept: ".Source li", drop: function(event, ui) { $(this).find(".placeholder").remove(); $("#Hf1").val(ui.draggable.text()); $("#TxtItemId").val($("#Hf1").val()); } }); }); </script> Now I want to access the value of the "TxtItemId" control in the code-behind through a postback. How do I go about doing this ? BTW, this is for a scenario where a person will drag an item from a panel into a shopping cart and I need to capture the Id of the dropped item and trigger a postback after the drop to update the quantity of that item in the cart.

  Read the article

• Stata output files in surveys

  - by William Shakespeare

  I have some survey data which I'm using Stata to analyze. I want to compute means of one variable by group and save those means to a Stata file. My code looks like this: svyset [iw=wtsupp], sdrweight(repwtp1-repwtp160) vce(sdr) svy: mean x I tried svy: by grp: mean x but that did not work. I could save each mean to a separate file by simply saying svy: mean x if grp==1 but that's inefficient. Is there a better way? Saving results to a file like one can use SAS ODS to capture results is also a need. I am not talking about the log here. I need the means and the associated group. I'm thinking estimates save [path],replace but I'm not sure if that will give me a Stata file or the group if I can figure out how to use by processing.

  Read the article

• ajax parameter to send correctly a variable to a specified url

  - by kawtousse

  I am trying to send data to a servlet from a js file but the servlet never received the parameter. so this is what I have: function showProject(prj) { xmlhttp=GetXmlHttpObject(); if (xmlhttp==null) { alert ("Browser does not support HTTP Request"); return; } var url="ServletxmlGenerator"; idprj = prj.options[prj.selectedIndex].value; //alert(idprj); url=url+"?idprj="+idprj; xmlhttp.onreadystatechange=stateChanged; xmlhttp.open("GET",url,true); xmlhttp.send(null); } and to capture th request it is with: public void doGet(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException { String projectcode=request.getParameter("idprj"); System.out.println("++++projectCode:=" +projectcode); the output is like: ++++projectCode:=null Can any one explain it to me it seems to be correct but i didnot find the error.Thinks

  Read the article

• unknown monitor in lenova laptop

  - by kumar

  I have set of two lenova laptops in which Fedora core 13 is installed. In one machine, the monitor is detected properly such that It is possible to connect another monitor. But In another laptop, monitor is shown as unknown monitor. I tried to fix it by reinstalling xorg-x11-drv-intel.i686. But the problem remains same(unknown monitor). it is not possible to connect another monitor with this setting. Laptop model: G460. Graphics card: Intel Graphics Media accelerator HD. Thanks!

  Read the article

• Choose an output audio device different from the default on WMP 11

  - by GetFree

  I like to play my music through a Hi-Fi audio equipment and everything else (like windows sounds, web videos and such) through my default PC speakers. On WIndows XP I had WMP 9 and I could do that with no problems since I can choose what audio device (which sound card) to use, and that selection is for WMP only, which can be different from Windows' default audio device. But now that I have Windows Vista and WMP 11 I cannot longer choose an audio device just for WMP, or at least I can't find a way to do it (the control in the options dialog is no longer there). Was this useful feature really removed from WMP 11? or there is some other way to do it?

  Read the article

• How to quickly switch monitors on multi-monitor setup? (W7)

  - by Saxtus

  At my desktop PC, I have 3 displays hooked up on my Palit GeForce GTX 480 to extend my desktop: DVI: Samsung SyncMaster T220 (22" 16:10, 1680x1050, as my main) DVI: Samsung SyncMaster 940BF (19" 4:3, 1280x1024) HDMI: Sony Bravia KDL-32D3000 (32" 16:9, 1360x768) As expected, the GFX card can only utilize 2 of the displays at any given time, so I have to manually switch using Windows' "Display Properties" dialog, each time I want to switch between them. I've tried UltraMon, DisplayFusion and PowerStrip (so please don't refer me to a question where those are given as solutions) but they are unable to switch monitors. Instead they can only change display resolutions and settings on the existing active monitors, with specially weird results when I've saved the monitor states and then tried to switch monitors using the saved states! Any idea on how to bypass the awful "Display Properties" dialog and it's "confirm your change" timer? Thanks in advance.

  Read the article

< Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >