Search Results

Search found 11318 results on 453 pages for 'josh close'.

Page 227/453 | < Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >

• snmpd agent sends duplicate traps

  - by jsnmp

  I am on Ubuntu 10.04.4 LTS, and I cannot upgrade to a higher version. I have installed the snmpd agent (NET-SNMP version 5.4.2.1) with an apt-get install snmpd command. When an event occurs which sends a trap, two traps are sent for each such event instead of one. For example, when I shut down the agent with command /etc/init.d/snmpd stop, two shutdown traps are sent to the destination host. If I then start back up the agent with command /etc/init.d/snmpd start, then two cold start traps are sent to the destination host. Is this a known issue? Is there a fix for this, or is there a configuration change that is needed to prevent the sending of the duplicate trap? These are the contents of the /etc/snmp/snmpd.conf file: rocommunity public authtrapenable 1 trap2sink <trap destination hostname> public These are the contents of the /etc/default/snmpd file: # This file controls the activity of snmpd and snmptrapd # MIB directories. /usr/share/snmp/mibs is the default, but # including it here avoids some strange problems. export MIBDIRS=/usr/share/snmp/mibs # snmpd control (yes means start daemon). SNMPDRUN=yes # snmpd options (use syslog, close stdin/out/err). SNMPDOPTS='-Ls3d -Lf /dev/null -u snmp -p /var/run/snmpd.pid -c /etc/snmp/snmpd.conf' # snmptrapd control (yes means start daemon). As of net-snmp version # 5.0, master agentx support must be enabled in snmpd before snmptrapd # can be run. See snmpd.conf(5) for how to do this. TRAPDRUN=no # snmptrapd options (use syslog). TRAPDOPTS='-Lsd -p /var/run/snmptrapd.pid' # create symlink on Debian legacy location to official RFC path SNMPDCOMPAT=yes

  Read the article

• MS Bing web crawler out of control causing our site to go down

  - by akaDanPaul

  Here is a weird one that I am not sure what to do. Today our companies e-commerce site went down. I tailed the production log and saw that we were receiving a ton of request from this range of IP's 157.55.98.0/157.55.100.0. I googled around and come to find out that it is a MSN Web Crawler. So essentially MS web crawler overloaded our site causing it not to respond. Even though in our robots.txt file we have the following; Crawl-delay: 10 So what I did was just banned the IP range in iptables. But what I am not sure to do from here is how to follow up. I can't find anywhere to contact Bing about this issue, I don't want to keep those IPs blocked because I am sure eventually we will get de-indexed from Bing. And it doesn't really seem like this has happened to anyone else before. Any Suggestions? Update, My Server / Web Stats Our web server is using Nginx, Rails 3, and 5 Unicorn workers. We have 4gb of memory and 2 virtual cores. We have been running this setup for over 9 months now and never had an issue, 95% of the time our system is under very little load. On average we receive 800,000 page views a month and this never comes close to bringing / slowing down our web server. Taking a look at the logs we were receiving anywhere from 5 up to 40 request / second from this IP range. In all my years of web development I have never seen a crawler hit a website so many times. Is this new with Bing?

  Read the article

• Turn off Windows Defender on your builds

  - by george_v_reilly

  I've spent some time this evening profiling a Python application on Windows, trying to find out why it was so much slower than on Mac or Linux. The application is an in-house build tool which reads a number of config files, then writes some output files. Using the RunSnakeRun Python profile viewer on Windows, two things immediately leapt out at me: we were running os.stat a lot and file.close was really expensive. A quick test convinced me that we were stat-ing the same files over and over. It was a combination of explicit checks and implicit code, like os.walk calling os.path.isdir. I wrote a little cache that memoizes the results, which brought the cost of the os.stats down from 1.5 seconds to 0.6. Figuring out why closing files was so expensive was harder. I was writing 77 files, totaling just over 1MB, and it was taking 3.5 seconds. It turned out that it wasn't the UTF-8 codec or newline translation. It was simply that closing those files took far longer than it should have. I decided to try a different profiler, hoping to learn more. I downloaded the Windows Performance Toolkit. I recorded a couple of traces of my application running, then I looked at them in the Windows Performance Analyzer, whereupon I saw that in each case, the CPU spike of my app was followed by a CPU spike in MsMpEng.exe. What's MsMpEng.exe? It's Microsoft's antimalware engine, at the heart of Windows Defender. I added my build tree to the list of excluded locations, and my runtime halved. The 3.5 seconds of file closing dropped to 60 milliseconds, a 98% reduction. The moral of this story is: don't let your virus checker run on your builds.

  Read the article

• C# Simple Twitter Update

  - by mroberts

  For what it's worth a simple twitter update. 1: using System; 2: using System.IO; 3: using System.Net; 4: using System.Text; 5:   6: namespace Server.Actions 7: { 8: public class TwitterUpdate 9: { 10: public string Body { get; set; } 11: public string Login { get; set; } 12: public string Password { get; set; } 13:   14: public override void Execute() 15: { 16: try 17: { 18: //encode user name and password 19: string creds = Convert.ToBase64String(Encoding.ASCII.GetBytes(string.Format("{0}:{1}", this.Login, this.Password))); 20:   21: //encode tweet 22: byte[] tweet = Encoding.ASCII.GetBytes("status=" + this.Body); 23:   24: //setup request 25: HttpWebRequest request = (HttpWebRequest)WebRequest.Create("http://twitter.com/statuses/update.xml"); 26: request.Method = "POST"; 27: request.ServicePoint.Expect100Continue = false; 28: request.Headers.Add("Authorization", string.Format("Basic {0}", creds)); 29: request.ContentType = "application/x-www-form-urlencoded"; 30: request.ContentLength = tweet.Length; 31:   32: //write to stream 33: Stream reqStream = request.GetRequestStream(); 34: reqStream.Write(tweet, 0, tweet.Length); 35: reqStream.Close(); 36:   37: //check response 38: HttpWebResponse response = (HttpWebResponse)request.GetResponse(); 39:   40: //... 41: } 42: catch (Exception e) 43: { 44: //... 45: } 46: } 47: } 48: }   BTW, this is my first blog post.  Nothing earth shattering, I admit, but I needed to figure out how to post formatted code.  In the past I’ve used Alex Gorbatchev’s Syntax Highlighter with great success, but here at GWB I couldn’t get it to work. Windows Live Writer though, being a stand alone writer, worked with no problems.  For now, that’s what I’ll use.

  Read the article

• How do I create a 2.5d parallax effect?

  - by Nikolay Dyankov

  I have a decent background in 3D graphics and programming, but I'm new to game development. I'm currently exploring different possibilities and I really want to make an RPG game. I was thinking about classic 2D isometric view, but I really love how Diablo 2 looks and feels to play. My question is - how can I achieve Diablo 2's parallax effect? Everything looks hand drawn with baked lights and shadows and looks awesome, but when you move around you notice some perspective. For example, let's say that I drew a big hall with columns in Photoshop with an orthographic perspective (classic pixel art style, just parallel lines). How would I give parallax effect to this scene when the character moves around? If I use camera-facing sprites for everything it would probably look OK in the distance, but it would be really fake when a character comes close to a column (cylinder) for example. Any suggestions? How did Blizzard make the parallax effect in Diablo 2? See this screenshot: http://guidesmedia.ign.com/guides/10629/images/act2tombs.jpg

  Read the article

• Tell me what&rsquo;s wrong! &ndash; An XNA sample demonstrating exception handling and reporting in

  - by George Clingerman

  I’ve always enjoyed using Nick Gravelyn’s exception handling in all of my games. You’re always going to encounter those unhandled exception that your players are going to ferret out and having a method to display them rather than just crashing to the dashboard is definitely more of an elegant solution. But the other day I got to thinking…what if we could do more? What if instead of just displaying the error, we could encourage the players to send us the error. So I started playing with that an expanding upon Nick’s sample code to see what I could come up with. I got close to what I envisioned, but unfortunately there were some limitations to just what the XNA API could do. In my head I was picturing the players hitting “Send Message” and a 360 message would just be sent to the XBLIG developer. Unfortunately, you can only send messages in an XNA game to someone you’re currently in a network session with. Since I didn’t want to have a 360 server running all the time, virally connecting to players just to get error messages, I did the next best thing and just open up a 360 message and encourage them to manually enter the gamertag. Maybe someday we’ll be able to do that a little better, but this works for now. In the sample, players can hit the “A” button or key to generate in an exception. If the debugger is not attached, then the Exception message screen will be shown explaining what has happened and giving the player a chance to send a 360 message to the gamertag provided or maybe even just send an email. Nick’s code has been changed just a bit. It now accepts any PlayerIndex (no longer hard coded to just PlayerIndex.One) and it no longer uses a MessageBox to get the users selection. The code has also been modified so that it works both for the 360 and for the PC. Check out “Tell me what’s wrong!” and let me know if you have any thoughts or suggestions. I really do appreciate the feedback.

  Read the article

• JRockit R28 "Ropsten" released

  - by tomas.nilsson

  R28 is a major release (as indicated by the careless omissions of "minor" and "revision" numbers. The formal name would be R28.0.0). Our customers expect grand new features and innovation from major releases, and "Ropsten" will not disappoint. One of the biggest challenges for IT systems is after the fact diagnostics. That is - Once something has gone wrong, the act of trying to figure out why it went wrong. Monitoring a system and keeping track of system health once it is running is considered a hard problem (one that we to some extent help our customers solve already with JRockit Mission Control), but doing it after something occurred is close to impossible. The most common solution is to set up heavy logging (and sacrificing system performance to do the logging) and hope that the problem occurs again. No one really thinks that this is a good solution, but it's the best there is. Until now. Inspired by the "Black box" in airplanes, JRockit R28 introduces the Flight Recorder. Flight Recorder can be seen as an extremely detailed log, but one that is always on and that comes without a cost to system performance. With JRockit Flight Recorder the customer will be able to get diagnostics information about what happened _before_ a problem occurred, instead of trying to guess by looking at the fallout. Keywords that are important to the customer are: • Extremely detailed, always on, diagnostics information • No performance overhead • Powerful tooling to visualize the data recorded. • Enables diagnostics of bugs and SLA breaches after the fact. For followers of JRockit, other additions are: • New JMX agent that allows JRMC to be used through firewalls more easily • Option to generate HPROF dumps, compatible with tools like Eclipse MAT • Up to 64 BG compressed references (previously 4) • View memory allocation on a thread level (as an Mbean and in Mission Control) • Native memory tracking (Command line and Mbean) • More robust optimizer. • Dropping support for Java 1.4.2 and Itanium If you have any further questions, please email [email protected]. The release can be downloaded from http://www.oracle.com/technology/software/products/jrockit/index.html

  Read the article

• Introducing the Industry's First Analytics Machine, Oracle Exalytics

  - by Manan Goel

  Analytics is all about gaining insights from the data for better decision making. The business press is abuzz with examples of leading organizations across the world using data-driven insights for strategic, financial and operational excellence. A recent study on “data-driven decision making” conducted by researchers at MIT and Wharton provides empirical evidence that “firms that adopt data-driven decision making have output and productivity that is 5-6% higher than the competition”. The potential payoff for firms can range from higher shareholder value to a market leadership position. However, the vision of delivering fast, interactive, insightful analytics has remained elusive for most organizations. Most enterprise IT organizations continue to struggle to deliver actionable analytics due to time-sensitive, sprawling requirements and ever tightening budgets. The issue is further exasperated by the fact that most enterprise analytics solutions require dealing with a number of hardware, software, storage and networking vendors and precious resources are wasted integrating the hardware and software components to deliver a complete analytical solution. Oracle Exalytics In-Memory Machine is the world’s first engineered system specifically designed to deliver high performance analysis, modeling and planning. Built using industry-standard hardware, market-leading business intelligence software and in-memory database technology, Oracle Exalytics is an optimized system that delivers answers to all your business questions with unmatched speed, intelligence, simplicity and manageability. Oracle Exalytics’s unmatched speed, visualizations and scalability delivers extreme performance for existing analytical and enterprise performance management applications and enables a new class of intelligent applications like Yield Management, Revenue Management, Demand Forecasting, Inventory Management, Pricing Optimization, Profitability Management, Rolling Forecast and Virtual Close etc. Requiring no application redesign, Oracle Exalytics can be deployed in existing IT environments by itself or in conjunction with Oracle Exadata and/or Oracle Exalogic to enable extreme performance and best in class user experience. Based on proven hardware, software and in-memory technology, Oracle Exalytics lowers the total cost of ownership, reduces operational risk and provides unprecedented analytical capability for workgroup, departmental and enterprise wide deployments. Click here to learn more about Oracle Exalytics.  

  Read the article

• Bot strategy in an arena

  - by joulesm

  I am writing the player's behavior for an arena game, and I'm wondering if you could offer some strategies. I'm writing it in Python, but I'm just interested in the high level game play. Here are the game aspects: Arena is a circle of a given size. The arena's size shrinks every round to help break any ties. Players are much smaller circles, and can be on teams of 1 or 2 players. Players attack by colliding with other players, and based on the physics of the collision (speed of both players, angle), one could force another player out of the arena. Once a player is out of the arena, they are out of the game (for that round). The goal is to be on the only team with players left in the arena. All other players have been pushed (through collisions or mistakes) out of the arena. It is possible for there to be no winner if the last two players exit the arena at the same time. Once the player has been programmed, the game just runs. There is no human intervention in the game. I'm thinking it's easiest to implement a few simple programmatic rules for my player to follow. For example, stay close to center of the arena, attack opponents from the inner side of the arena, etc. Are there any good simple game strategies? Would adding a random aspect to the game help? For example, to avoid predictability by the other team or something. Thanks in advance.

  Read the article

• Auto Save and Auto Load Game onto the Device's Storage Concept Question

  - by David Dimalanta

  I'm trying to make a simple app that will test the save and load state. Is it a good idea to make an app that has an auto save and load game feature only every time the newbies open the first app then continues it on the other day? I tried making a sprite that is moving, starting at the center. When I close and re-open the app, the sprite goes back to the center instead of the last coordinate where the sprite land on this part (i.e. at the top). The thing I want to know how the sequence of saving and loading goes like this: I open the app The starting sprite at the center. It displays a coordinate of the sprite plus number of times does the sprite move. I exit the app that automatically saves the game without notice. Finally, when I re-opened it, it automatically loads the game retaining the number of times the sprite move, coordinates, and the sprite's area landed. These steps above are similar, but not the sprite movement test app, to the sequence of saving and loading the game's level and record in Jewel Stackers for the Android app. And, by default, if there is no SD card in any tab or phone that runs on Android, does it automatically save/load onto the internal drive or the APK file itself? Is it also useful to use auto save and auto load feature for protecting and fetching informations (i.e. fastest time, last time where the sprite is located via coordinates, etc.)?

  Read the article

• Implementing a multilanguage AI contest platform

  - by Alejandro Piad

  This is a followup to this question. To sum: I'm implementing an AI contest site, where each user may submit several AI implementations for different games. Think about Google AI Challenge but instead of just having a big event once a year, I would like it more on a league fashion, with all virtual players playing with each other every some close period of time. I want to support as many programming languages as possible. I've seen that contest sites (like codeforces) ask you to submit a source code and interact through stdin and stdout. The first question is: what is the best way of supporting multiple languages? As I see it, I can either ask people to upload some binary/script, and interact either through stdin/*stdout*, or sockets, or the file system; or ask people to submit source code, and wrap it with whatever is necessary for the interaction. I would like to skip the need to compile the code by myself (in the server, I mean), but I am willing to do it if its the "best" choice. I need to comunicate virtual players with each other, or even better, with some intermediary arbiter. The second question is regarding security. If I'm going to be running user code in my server, I want to ensure strict security conditions, like no file system access, no networking, etc. Otherwise it would be a safe heaven for hackers. I will be implementing the engine/arbiter in .NET. I would like to support at least C#, C++, Java and Python for the user's implementations. I'm willing to write interfaces for each of these languages to simplify the user interaction with the system. Thanks in advance.

  Read the article

• How important do you find exception safety to be in your C++ code?

  - by Kai

  Every time I consider making my code strongly exception safe, I justify not doing it because it would be so time consuming. Consider this relatively simple snippet: Level::Entity* entity = new Level::Entity(); entity->id = GetNextId(); entity->AddComponent(new Component::Position(x, y)); entity->AddComponent(new Component::Movement()); entity->AddComponent(new Component::Render()); allEntities.push_back(entity); // std::vector entityById[entity->id] = entity; // std::map return entity; To implement a basic exception guarantee, I could use a scoped pointer on the new calls. This would prevent memory leaks if any of the calls were to throw an exception. However, let's say I want to implement a strong exception guarantee. At the least, I would need to implement a shared pointer for my containers (I'm not using Boost), a nothrow Entity::Swap for adding the components atomically, and some sort of idiom for atomically adding to both the Vector and Map. Not only would these be time consuming to implement, but they would be expensive since it involves a lot more copying than the exception unsafe solution. Ultimately, it feels to me like that time spent doing all of that wouldn't be justified just so that the a simple CreateEntity function is strongly exception safe. I probably just want the game to display an error and close at that point anyway. How far do you take this in your own game projects? Is it generally acceptable to write exception unsafe code for a program that can just crash when there is an exception?

  Read the article

• External monitor is blank if I boot with the monitor plugged in

  - by Ronald

  Ubuntu 12.04 has problem with Intel GM45 Chipset, featuring the the Mobile Intel® Graphics Media Accelerator (GMA) 4500MHD I have a COMPAQ Presario CQ70 laptop with an Intel GM45 chipset that features the Mobile Intel® Graphics Media Accelerator (GMA) 4500MHD. I was using the second HDMI video port to drive both a projector or a second monitor. Everything was working fine under Ubuntu 8.04, 9.04, 10.04 and 11.04, however, when I upgraded to 12.04 the second monitor stopped working. What I mean when I say stopped working is: boot with monitor plugged in. Blank screen! Power off, unplug monitor and power on everything works. Plug in monitor (only mode that works in Mirror mode) two monitors that look same. Close laptop lid. screen goes blank only option for useful system is power off and unplug monitor. If I attempt to Adjust the monitor to maximum resolution that the monitor will handle and turn off mirror mode nothing can be moved onto that screen. This all worked fine with earlier versions of Ubuntu, is there a notes about the changes to the graphics management system in 12.04, like there is for the resolver change?

  Read the article

• Blank screen after Switch User or Resume

  - by matt wilkie

  About half the time when I switch users or resume from standby or resume the screen goes blank (black). If I work the cursor keys I can hear the system bell when it gets to the end of the user list. I can also successfully login, going from memory, but screen stays black. Sometimes closing and re-opening the lid will light up the screen again. Pressing the special Function key to enable/disable external monitor connection has no effect [Fn]-[F5],[Fn]-[F6]. If none of the previous work I need to put the computer into hibernation or full power off to restore screen function. If I watch closely when switching users I think I can see the screen initially start to light up and then quickly fade to black. The computer is an Acer Aspire 3500, model ZL6, running Ubuntu 10.10 installed 2 days ago. No proprietary drivers are in use. I'll provide a list of hardware details as soon as I can figure out how to generate that (didn't there used to be an entry for hardware details under the System menu?). Possibly related questions: No resume after Hibernate or Standby When I resume from suspension - the screen is blank Switch user fails to complete successfully For what it's worth, blank after resume also used to happen occasionally when the laptop was running XP-Home, but nowhere near as often, perhaps 6 or 8 times a year. UPDATE: I found System Administration System Testing and ran the Monitor test. It went very very dark, but the window elements could be discerned, and the whole screen flashed (from very very dark to black). On the third repeat of that same test the screen went to full blaupck and stayed there. Moving the mouse, via touchpad, or touch keys did not wake it up again. I had to close the lid and put the computer into hibernate, and press the power button to restore it. UPDATE2: output of lshw: http://pastebin.com/q7n8676r, lspci: http://pastebin.com/6ujzVK4r UPDATE3: sometimes I can restore the screen by flipping to console 1 with ctrl-alt-F1 and then back to graphical with ctrl-alt-F7.

  Read the article

• DAO/Webservice Consumption in Web Application

  - by Gavin

  I am currently working on converting a "legacy" web-based (Coldfusion) application from single data source (MSSQL database) to multi-tier OOP. In my current system there is a read/write database with all the usual stuff and additional "read-only" databases that are exported daily/hourly from an Enterprise Resource Planning (ERP) system by SSIS jobs with business product/item and manufacturing/SCM planning data. The reason I have the opportunity and need to convert to multi-tier OOP is a newer more modern ERP system is being implemented business wide that will be a complete replacement. This newer ERP system offers several interfaces for third party applications like mine, from direct SQL access to either a dotNet web-service or a SOAP-like web-service. I have found several suitable frameworks I would be happy to use (Coldspring, FW/1) but I am not sure what design patterns apply to my data access object/component and how to manage the connection/session tokens, with this background, my question has the following three parts: Firstly I have concerns with moving from the relative safety of a SSIS job that protects me from downtime and speed of the ERP system to directly connecting with one of the web services which I note seem significantly slower than I expected (simple/small requests often take up to a whole second). Are there any design patterns I can investigate/use to cache/protect my data tier? It is my understanding data access objects (the component that connects directly with the web services and convert them into the data types I can then work with in my Domain Objects) should be singletons (and will act as an Adapter/Facade), am I correct? As part of the data access object I have to setup a connection by username/password (I could set up multiple users and/or connect multiple times with this) which responds with a session token that needs to be provided on every subsequent request. Do I do this once and share it across the whole application, do I setup a new "connection" for every user of my application and keep the token in their session scope (might quickly hit licensing limits), do I set the "connection" up per page request, or is there a design pattern I am missing that can manage multiple "connections" where a requests/access uses the first free "connection"? It is worth noting if the ERP system dies I will need to reset/invalidate all the connections and start from scratch, and depending on which web-service I use might need manually close the "connection/session"

  Read the article

• How to handle growing QA reporting requirements?

  - by Phillip Jackson

  Some Background: Our company is growing very quickly - in 3 years we've tripled in size and there are no signs of stopping any time soon. Our marketing department has expanded and our IT requirements have as well. When I first arrived everything was managed in Dreamweaver and Excel spreadsheets and we've worked hard to implement bug tracking, version control, continuous integration, and multi-stage deployment. It's been a long hard road, and now we need to get more organized. The Problem at Hand: Management would like to track, per-developer, who is generating the most issues at the QA stage (post unit testing, regression, and post-production issues specifically). This becomes a fine balance because many issues can't be reported granularly (e.g. per-url or per-"page") but yet that's how Management would like reporting to be broken down. Further, severity has to be taken into account. We have drafted standards for each of these areas specific to our environment. Developers don't want to be nicked for 100+ instances of an issue if it was a problem with an include or inheritance... I had a suggestion to "score" bugs based on severity... but nobody likes that. We can't enter issues for every individual module affected by a global issue. [UPDATED] The Actual Questions: How do medium sized businesses and code shops handle bug tracking, reporting, and providing useful metrics to management? What kinds of KPIs are better metrics for employee performance? What is the most common way to provide per-developer reporting as far as time-to-close, reopens, etc.? Do large enterprises ignore the efforts of the individuals and rather focus on the team? Some other questions: Is this too granular of reporting? Is this considered 'blame culture'? If you were the developer working in this environment, what would you define as a measureable goal for this year to track your progress, with the reward of achieving the goal a bonus?

  Read the article

• How do you avoid jumping to a solution when under pressure? [closed]

  - by GlenPeterson

  When under a particularly strict programming deadline (like an hour), if I panic at all, my tendency is to jump into coding without a real plan and hope I figure it out as I go along. Given enough time, this can work, but in an interview it's been pretty unsuccessful, if not downright counter-productive. I'm not always comfortable sitting there thinking while the clock ticks away. Is there a checklist or are there techniques to recognize when you understand the problem well enough to start coding? Maybe don't touch the keyboard for the first 5-10 minutes of the problem? At what point do you give up and code a brute-force solution with the hope of reasoning out a better solution later? A related follow-up question might be, "How do you ensure that you are solving the right problem?" Or "When is it most productive to think and design more vs. code some experiments to and figure out the design later?" EDIT: One close vote already, but I'm not sure why. I wrote this in the first person, but I doubt I'm the only programmer to ever choke in an interview. Here is a list of techniques for taking a math test and another for taking an oral exam. Maybe I'm not expressing myself well, but I'm asking if there is a similar list of techniques for handling a programming problem under pressure?

  Read the article

• 2D map/plane with nodes overlayed that supports panning, scaling and clicking on nodes

  - by garlicman

  I'm trying my hand at Android development and seem to be running into an invisible ceiling in trying to get what I want accomplished. Basically I'm trying to create an app that renders a 2D surface map that I can (pinch) zoom and pan. I'll have to place nodes on the surface of the map that will scale/zoom and pan in relation to the surface. I started out with a 2D ImageView approach and got as far as pinch zoom, pan and laying nodes as relative ImageViews, but all the methods I tried to get X,Y,W,H for the 2D surface were always off for some reason. Additionally, I was never able to scale the node ImageViews correctly, and as a result never got far enough to try and work out their X,Y scaled offset. So I decided to get back to 3D rendering. Conceptually pan/zoom is camera manipulation, so I don't have to mess with how to scale the 2D map or the nodes. But I need a starting point or sample to get me going that's close to what I'm trying to achieve. A sample on a translucent spinning cube isn't helping as much as I need it to. Any tips? Links, insults and sympathy are all welcome!

  Read the article

• Does concurrency inherently introduce "randomness" into a game?

  - by Jeff

  When a game is implemented with concurrency (as most games are), does this necessarily, by its very nature, introduce an element of randomness into the game that is outside of the players' control? Note that when I use the word "random", I'm not meaning to launch into a philosophical debate about the deterministic nature of the system. I understand that concurrency is deterministic in the sense that the operating system decides which processes to allow time on the CPU and in what order (or the JVM controls which Thread's turn it is to execute, etc). But my understanding of this is that there is no way to control or predict whether one thread's next command will execute before or after another. The reason I'm asking is because this seems like a fundamental difficulty for game development where a game is supposedly designed around a player's skill. Consider a game like League of Legends. Assume that two players are battling it out. It's a very close contest between the two and it's coming down to the wire -- so much so that whoever gets their last attack off will be the one to kill the other and win the game for their team. If the players are implemented using concurrency and the situation really was like this, is it essentially out of the players' hands at this point? Is the outcome of this match all up to whatever system is arbitrarily deciding which player's thread/process will execute next? If not, what am I misunderstanding about concurrency? If so, is there any way around this problem so that a game of skill can always be a game of skill, especially in those most crucial moments?

  Read the article

• Disable Password Complexity/Expiration etc. Policy on Windows Server 2008

  - by Sahil Malik

  Ad:: SharePoint 2007 Training in .NET 3.5 technologies (more information). One of the things I like to do, for development environments only is to get rid of that excessively bothersome password policies. I like to have my password as something like p@ssword1, so they are easy to remember etc. etc. Obviously never do this in production. However, Windows Server 2008 comes with a password policy that expires my passwords every 90 days, and requires me to pick complex passwords, can’t reuse passwords etc. etc. Well here is how you disable password policy on a Windows Server 2008 machine - Run Group Policy Management (gpmc.msc) Expand to your domain, look for Forest\Domains\yourdomain\default domain policy. Go to the settings tab, right click on the tab, and choose “Edit”. This will open the Group Policy Management Editor, in which - Go to Computer Configuration\Policies\Windows Settings\Security Settings\Account Policies\Password Policy, and change the policy to whatever that suits you. Close everything, and run command prompt as administrator, and issue a “gpupdate /force” command to force the group policy update on the machine. Restart, and you’re done! :) Comment on the article ....

  Read the article

• ASP.NET 4 Hosting :: How to set up Forms Authentication for your ASP.NET web site

  - by mbridge

  Please follow this steps: 1. Log in to your Control Panel. 2. From the menu, select Databases ? SQL Server 2008. 3. Click the Create User button. 4. Enter a user name and password and click Save. In this demonstration, the user name is dotnetuser and the password is dotnetuserpass. 5. Click the Create Database button. 6. Enter a database name and grant access to the user you created above and click Save. In this demonstration the database is called DotNetAuthentication. 7. Locate and run the ASP.NET SQL Server Setup Wizard. This file is located in your .NET framework directory and is named aspnet_regsql.exe (example: C:\Windows\Microsoft.NET\Framework64\v4.0.30319\aspnet_regsql.exe). 8. Click Next and choose Configure SQL Server for application services. 9. Click Next and enter the server name and database log in credentials. The server name is the web site pointer address to where your application will be published and the log in credentials are the SQL server user name and password created earlier. 10. Click Next twice and the wizard will take a moment to complete the scripting actions that populate the new database with all the objects necessary to configure the ASP.NET provider.  Once complete, click Finish to close the wizard. 11. Finally, modify the web.config file in your ASP.NET web application to use the database you created.

  Read the article

• ubuntu 12.10 installation failure

  - by Eidelmaim

  Here i am asking this question again because someone deemed it a duplicate to another topic which i over looked and NOTHING AT ALL in that topic pertained to my problem. If your going to close a topic believing it is a duplicate at least do somke reasearch into WHY you think its a duplicate and provide a like to a better source. How do i get past this installation username and password issue? I downloaded ubuntu 12.10 directly from Ubuntu.com and created a bootable USB with linuxlive. after loading the boot drive and ubuntu begins, it goes directly from the purple ubuntu startup screen directly to a black DOS like prompt asking for a ubuntu login. this is COMPLETLY before any installation -begins. i need some help with this. FYI : this is what it is saying after it goes to the login area in the DOS (Full black screen) like screen. Ubuntu 12.10 ubuntu tty1 ubuntu login: now i will provide a few images of the problem i am having. and because i DONT HAVE ANY OS on the computer BECAUSE ubuntu WONT go PAST this... i have to snap these pictuires with a cell phone and upload on another PC. these links are in chronological order from time of pressing power button to time i am presented with log in screen : image 1 image 2 can only post 2 links in messages... will post additional links in comments So, again... how do i get past this ? this is entireley before ubuntu is installed on my system. my PC specs... Homebuilt computer: Motherboard is a Asus Sabertooth x58 with a intel core i7 processor. Mushkin memory @ 12gbs. 4ea. Seagate 150gb hard drives. nvidia GTX 260 graphics card. i initially attempted to install to raid 5. failed. i broke down the raid and attempted to install to a single drive with all other drives disconnected from the PC. again, thanks in advanced for any assistance.

  Read the article

• I have a ESXi 5.0 installed and when I am Installing Ubuntu Server 12.04 LTS it is giving an error saying grub installation failed?

  - by Rishee

  I have a ESXi 5.0 installed and when I am Installing Ubuntu Server 12.04 LTS (32 bit) it is giving an error saying grub installation failed? Please check the below screenshot of the error. I have other Ubuntu servers running fine on this esxi server, so I don't think problem is with ESXi. I have 32 GB of ram spare on this ESXi and have given 2 GB of RAM to this 12.0 LTS VM. I have given 2 cores of processor. I have tried supplying different ISO Image to this VM as I thought the 1st image that I downloaded has errors.. But defiantly that's not the case as all 3 different ISO images that I downloaded of Ubuntu server 12.04 LTS (32-bit) can't be corrupt!! Just to make sure that the Image does not have problem I used that Image to install it for testing on stand alone system. it works fine there!! This is a production ESXi server with which I can't play with, how ever I can play whith the Ubuntu Server 12.04 LTS (32-Bit) VM that we have created on that ESXi. I need help on this as soon as possible. go live date of this server is really close. (This Question is already there on Super user and Server Fault.)

  Read the article

• Using HTML5 Today part 2&ndash;Fixing Semantic tags with a Shiv

  - by Steve Albers

  Semantic elements and the Shiv! This is the second entry in the series of demos from the “Using HTML5 Today” talk. For the definitive discussion on unknown elements and the HTML5 Shiv check out Mark Pilgrim’s Dive Into HTML5 online book at http://diveintohtml5.info/semantics.html#unknown-elements Semantic tags increase the meaning and maintainability of your markup, help make your page more computer-readable, and can even provide opportunities for libraries that are written to automagically enhance content using standard tags like <nav>, <header>,  or <footer>. Legacy IE issues However, new HTML5 tags get mangled in IE browsers prior to version 9.  To see this in action, consider this bit of HTML code which includes the new <article> and <header> elements: Viewing this page using the IE9 developer tools (F12) we see that the browser correctly models the hierarchy of tags listed above: But if we switch to IE8 Browser Mode in developer tools things go bad: Did you know that a closing tag could close itself?? The browser loses the hierarchy & closes all of the new tags.  The new tags become unusable and the page structure falls apart. Additionally block-level elements lose their block status, appearing as inline.    The Fix (good) The block-level issue can be resolved by using CSS styling.  Below we set the article, header, and footer tags as block tags. article, header, footer {display:block;} You can avoid the unknown element issue by creating a version of the element in JavaScript before the actual HTML5 tag appears on the page: <script> document.createElement("article"); document.createElement("header"); document.createElement("footer"); </script> The Fix (better) Rather than adding your own JS you can take advantage of a standard JS library such as Remy Sharp’s HTML5 Shiv at http://code.google.com/p/html5shiv/.  By default the Modernizr library includes HTML5 Shiv, so you don’t need to include the shiv code separately if you are using Modernizr.

  Read the article

• SQLAuthority News – NuoDB MeetUp on Nov 8, 2012 in Seattle

  - by pinaldave

  I am pleased to let you know that I will be attending again this year’s SQLPASS conference in Seattle and look forward to meeting all of you while at the conference. In the next two weeks, I will provide you with a full agenda of where I will be during PASS. During the week, I will also be stopping by at the NuoDB MeetUp, which will be held close by at the Edge Grill at 1522 6th Ave in Seattle on Thursday, November 8th. This will be an excellent opportunity for you to learn more about their brand new distributed, peer-to-peer database solution, which I believe will revolutionize SQL cloud database technology in the 21th century.  I have been personally following NuoDB for months now and am very excited about the architecture and capabilities of this innovative product. Wiqar Chaudry, NuoDB technology evangelist, will give a presentation and demonstration of their elastically scalable SQL cloud database in this Meetup event.  Prior to joining NuoDB, Wiqar was a Senior Architect at Epsilon, the data intelligence company with big brand name customers in insurance, consumer goods, etc.  He’s also going to discuss how NuoDB compares with Azure, the hometown favorite, and why cloud-based SQL deployment will pave the way for the future. I will be at the NuoDB MeetUp to briefly talk about my own experiences with NuoDB and will be giving away some signed copies of my latest book as well will have some interesting goodies. So please join me and the NuoDB team at their Meetup event. RSVP here. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: NuoDB

  Read the article

< Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >