Search Results

Search found 10489 results on 420 pages for 'usb keyboard'.

Page 231/420 | < Previous Page | 227 228 229 230 231 232 233 234 235 236 237 238  | Next Page >

  • Ubuntu 12.04 + Bluetooth problems with maintaining connection

    - by ifndefx
    I have an Apple Wireless Mouse, Apple Wireless Keyboard, Apple Wireless Trackpad, and a pair of headphones. All of these connect to the computer via a Bluetooth dongle. After several hours I've managed to get the devices paired (all except the headphones) with the computer. However, I'm facing a problem where a connection can't be maintained even with one device. I first started with the gnome bluetooth applet, this couldn't even pick up devices, so I installed blueman, and this at least detected the devices but it couldn't keep the connection going. Then i read somewhere to get hidd installed and use the command line using the mac address of the device (which I got from blueman) and this worked really well, the connection was stable, but there's still a couple of issues that I need help with: If I am to use hidd I need to execute this via terminal, which means for the keyboard and the mouse I need to have two of each. This doesn't make sense. I need the bluetooth daemon to have started with the devices picked up a lot earlier, and especially at grub bootloader. The mouse and the trackpad both work if i use hidd, however, I cannot get the right mouse to work nor the scroll wheel to work. The headphones don't work period, they don't work with any of the bluetooth applets, and with hidd either. When I use blueman aplet, it attempts to pair and states 'Authentication Rejected". The headphone is Phillips SHB9100. If someone can help me with this, I would be grateful.

    Read the article

  • Why don't my Fn keys work for brightness or media after upgrading?

    - by Adina G
    I recently upgraded from 11.04 to 11.10. After the upgrade, I can no longer adjust the screen brightness or the volume using keyboard (before the upgrade, using Fn+F4, Fn+F11, etc. worked). Using Fn+F2 to disable wireless still works, so I guess the Fn key itself is being recognised. I tried to follow the instructions here, but I don't have a file in /etc/X11 called xorg.conf. I also tried following this workaround, but it had no noticeable effect. I've also tried going to Settings ? Keyboard ? Shortcuts and reassigning the brightness and volume controls, both to the default keys and to new combinations. These changes don't have an effect even after rebooting. Googling has found bug reports where pressing the media keys brings up a "no entry sign" rather than changing the volume. When I press the keys there's no response at all. I've also seen various people say a workaround is to have totem running in the background; this doesn't work for me either. Finally, I tried installing keytouch; I was able to install keytouch-editor but got the message "Unable to locate package keytouch". Any more ideas? I'd be very grateful if anyone could help me (even by pointing to a thread I've missed)!

    Read the article

  • I have Ubuntu only and need to install Windows

    - by Terzuz
    I had Windows 8, I installed Ubuntu for a new OS, Then I want to sadly go back to Windows , I have a Windows Vista *.iso but I can't boot from it. When I try to extract the '.iso file and have the contents on my USB so it can boot up , When I restart and click F9 for my Boot Device Options , Only my Hard Drive and CD ROM are there but my "Generic Flash Drive" is not , But when I do not have Windows Vista '.iso on it , It will show up in the list. How can I make a partition of some sort, Provide instructions since I am new at this all , then I need to be able to use the Windows Vista installer and install Windows Vista, I would like Dual-Boot if possible. Info: I have the HP 2000 Laptop (Mine was removed from the Best Buy Website so the closest laptop to the specifications and the design is the link at the bottom) I am running Ubuntu 12.10. I have 4GB of RAM , 220 GB in my Hard Drive left , I have a USB Flash Drive which works sometimes , other times it fails. Note - I tried using GParted in Ubuntu but I had a problem where the main drive with 220 GB Free was locked , I am not sure what to do and can not find the correct forum. http://www.bestbuy.com/site/HP+-+Pavilion+15.6"+Laptop+-+4GB+Memory+-+320GB+Hard+Drive+-+Pewter/5043836.p?id=1218608951204&skuId=5043836

    Read the article

  • Ubuntu 14.04 LTS 64-bit install alongside Windows 7

    - by user289222
    I've tried installing Ubuntu 14.04 LTS alongside my Windows 7 OS, following the exact procedure given by the Ubuntu website and random other tutorials. I've tried with a LiveCD and with a USB stick but I always run into the same problem. When I'm at the screen where I'm allowed to select how I want to install Ubuntu ("alongside", "erase Windows 7", "something else"), the first option says "Install Ubuntu inside Windows 7" instead of "Install Ubuntu alongside Windows 7". From pretty much all tutorials I've seen, the tutorial says that the option should say "alongside". I click "inside" anyway, and Ubuntu doesn't install at all. Instead, my computer just reboots, and goes back to the Try Ubuntu or Install Now screen. This happens regardless of using a LiveCD or a USB stick. I've also tried manually resizing my partitions using "something else". Oddly, I see 4 sda partitions: /dev/sda type size used /dev/sda1 1mb unknown Windows 7 (loader) /dev/sda2 ntsf 208mb unknown Recovery Windows Environment (loader) /dev/sda3 ntsf ~752000mb unknown Recovery Windows Environment (loader) /dev/sda4 ~18000mb unknown I try resizing the largest partition, but some sort of internal error occurs and it doesn't let me resize my partitions. Any ideas on what's going on and how to solve it?

    Read the article

  • Librated error when creating partition table

    - by Marko
    I bought a Dell Inspiron 5521 laptop a few days ago that came with Ubuntu preinstalled. I haven't used Ubuntu yet, and I don't have any experience in using it. I wanted to install Windows 7 64-bit on my laptop alongside Ubuntu, and made two bootable USB drives with Gparted and Windows 7. There wasn't a suitable partition on my laptop in which I could install Windows 7. I've read the instructions for using Gparted to create or manage my hard drive. I inserted the USB, booted from BIOS, and followed the procedure in installing Gparted. Then I entered Gparted, and the following error occurred: Librated error when Creating partition table. It asked me to click on either OK or Cancel. Either way I had my hard disk shown to me in the user window, in partitions that were made by the manufacturer: Partition File sys Label Size Flags /dev/sda1 fat32 dellutility 300.00 Mib diag /dev/sda2 fat32 os 3.00 Gib lba /dev/sda3 ext4 912.46 Gib boot /dev/sda4 extended 15.75 Gib (had a subpart) /dev/sda5 linux-swap 15.75 Gib ...and a option to switch to dev/sdb that's unused and of capacity 3Gib. I've used the biggest partition 912.46 Gib, and tried to reduce its size, and clicked OK. Then when I tried to make a new partition, it said it can't make any more partitions, no more than a maximum of 5. I would like to keep Ubuntu and slowly learn, but I also need to use programs that work in Windows. Thank you for taking the time to answer my question.

    Read the article

  • Can't install on a Thinkpad W700ds

    - by Habstinat
    I want to install Ubuntu on my computer. I don't know much about Linux, but I know my way around a terminal and whatnot. My computer, a ThinkPad W700ds, refuses to read from my CD when booting. The md5sum is correct and the same CD boots fine from another computer. When I try to install from a USB, I can get the main screen, but when I select any of the options from there my screen turns black for more than 3 hours until I have to turn it off. Is there anything I can do about this? I want to have a true partition, don't want a Wubi'd install. It's a 10.10 x64 image, but my computer is 64 bit (running Windows 7 x64 right now) and the exact same CD is bootable on other computers. I've been on #ubuntu IRC for days trying to work this out but nobody knew, so I figured I would get more responses by posting to here. UPDATE: Thanks Jorge Castro. Both the alternate and desktop installers seem to not work at all with the CD. On a USB, the alternate installer lets me start installing, but in the middle of installation I get this message. The people on #ubuntu told me to just exit installation at that point, so I did.

    Read the article

  • Can't access computer

    - by Pudica
    I'm running Ubuntu 14.04 on an Intel NUC and it won't boot! The last successful boot was earlier today but now each time I try it gets stuck on the Grub menu where it prompts for memory check etc. This is not a dual boot system, so this screen shouldn't ever appear, and it never has before. It's GRUB version 2.02~beta2-9, which is a little disconcerting, as I'm on the stable sources. Unfortunately the keyboard (I've tried 2 keyboards just in case) is not responding at this point in the boot process, so I can't select the "Ubuntu" menu option in Grub. The keyboard works during the bios stage, so I can configure it to boot from USB, and I tried a flash drive with 14.04 on it. The flash drive works in my laptop but is completely ignored by the NUC (I tried all 3 USB ports!). It seems that I have no way of getting into the machine at all! The Intel support site was my first option, but the site is down. I expect it's a long shot, but if anyone has any ideas I'd be very grateful.

    Read the article

  • Win8 x64 Laptop (Samsung) unable to boot after installing Ubuntu

    - by user285872
    I posted here a while back and no one was able to help me so I am going to try to explain my problem better. I have a Samsung series 7 Ultrabook and I connected a USB optical drive with an Ubuntu 14.04 installation disc. I did not set or change any of my partitions, however, as I mainly wanted to just be able to boot from the disc and fool around with Ubuntu. Upon restarting my computer I get a blue-screen message saying: Recovery Your PC needs to be repiared The Boot configuration date file is missing some required information. File: \BCD Error Code: 0xc000000d You'll need to use the recovery tools on your installing media. If you don't have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. However I am never given the option to even try to boot to anything. When I turn my computer on the optical drive spins and then after a moment or two comes to a halt. I turned off safeboot and switched it to CSM (I believe that is what it is called) mode, and that makes it so when I turn my computer on it takes me to a Windows Recovery screen. I am able to change the date I want to recover and view all the applications installed, however upon recovering Windows says "All boot options are tried. Press key to recover with factory image using Recovery or any other keys for next boot loop iteration." It seems to be stuck in a loop. Can someone please help me?! I'm so confused and nothing is working!

    Read the article

  • How to prevent computer from automatically sleeping and/or hibernating?

    - by mehaase
    I'm running Ubuntu 12.04, and my laptop* won't wake from sleep/suspend/hibernate. (Is sleep the same thing as suspend?) I'm not even sure which of these things it's doing. When I am done working for the day, I lock my screen (Control-Alt-L). When I come back the next day, the screen is in power saving mode, and no amount of typing or clicking (on the usb keyboard/mouse or the builtin keyboard/trackpad) nor tapping the power button will bring it back to life. The only way I can get my machine to work is to hold down the power button until it shuts off, then press the power button again to turn it back on. Obviously, anything I had open from the previous day is pretty much gone -- in particular, my VMs all get rudely shut down without any warning. This is driving me INSANE. I spend the first hour of every work day trying to figure out how to get my computer to stop locking up over night. What I've tried: Editing the org.freedesktop.upower.policy to disable suspend and hibernate. Setting power management options in "Power" section of "System Settings". Looking at all power management options in the BIOS (none appear to be relevant to sleep/suspend/hibernate). Reading every forum post/askubuntu post that I can find that's even tangentially related to the subject. My question: how to disable the automatic sleep and/or hibernate (and/or anything similar) in Ubuntu 12.04. I don't care if it's still possible to sleep/suspend/hibernate/whatever by pushing buttons or running some command or reciting led zeppelin lyrics backwards. I just want my laptop to be ready for work in the morning. *The laptop is a Dell Latitude something or other. I don't want to get too specific because I've seen a lot of similar questions get closed for being too specific. I think my question is generic enough to stand -- it's a question about the latest, stable version of Ubuntu.

    Read the article

  • Ubuntu 12.04 "stuttering"

    - by Totte
    When I log in to the desktop Ubuntu seems to "stutter". Doing pretty much anything causes the cursor to freeze for a few seconds, and the rest of the screen updates something like every 15 seconds (during these 15 seconds I can still move the cursor). For example, opening the home folder I first see no effect, followed by a semi-transparent home folder, and finally the folder as it should be (this can take like 30 seconds); no animation, just three individual frames. Also, I sometimes don't see a window for a program, even though the program in question is supposed to be "up". Since this is my first experience of Linux, I confess I have no idea where to start - searching the web I only found problems with complete freezes/crashes requiring rebooting, as opposed to this "stuttering". I installed Ubuntu 12.04 32bit from a bootable USB stick a couple of days ago, right after a fresh Vista 32bit install. Thinking the stuttering might stop if I updated Ubuntu, I managed to install approx 270 updates through the Update Manager, but the stuttering was still there. Apart from the updates, I haven't installed any software other than what was included on the bootable USB stick. Vista and Ubuntu are on a single Crucial m4 SSD, in a dual-boot setup, with GRUB. CPU: Intel Core 2 Quad Q6600 GPU: Nvidia GeForce 8800 GTX (with the recommended proprietary drivers) RAM: 2GB DDR2

    Read the article

  • How do I solve "System is running in low graphics issue" in Ubuntu INSTALLER ?

    - by hellodear
    I made a bootable USB for installing Ubuntu 12.04 LTS alongside Windows 8.1. I inserted my USB device and then booted into it. Then it showed me 2 options - 'Try Ubuntu' or 'Install Ubuntu'. Now I press 'Try Ubuntu' and then it says, "The system is running in low graphics mode". Then I press 'OK'. Then it showed me 4 options. Then again I click 'OK'. Then it shows a black screen and nothing happens. I have tried all possible answers provided in AU. What should I do? Please help. PS :- I am using Windows 8.1 with dedicated graphic card which is AMD Radeon HD 8670M. I am trying to do this in a Dell Laptop 3537 Inspiron. UPDATE :- I tried running the liveUSB session with nomodeset on and i was able to enter the installer. But when I run boot-repair(so that my Ubuntu gets detected in the GRUB menu) after installing Ubuntu successfully alongside Windows 8(following this tutorial with nomodeset on, I get the following error:- your system is running in legacy mode boot repair done

    Read the article

  • Very slow wireless connection (unrelated to power management) using Netgear N150 WNA1100 in 12.04

    - by vgaldikas
    I am using a Netgear N150 WNA1100 USB Adapter. The network driver is: ath9k_htc. When I use Ubuntu 12.04 my wireless connection is much slower than when I use the WNA1100 with my Windows 7 installation on the same machine. I have been researching this and the most common reason for this seems to be related to power management. However for me this is off by default. I had entered a bunch of different commands and, at one stage, I got it to work at full power. But then I rebooted the machine and it went back to slow again. After entering the different commands I was afraid that I may have messed something up, so I performed a fresh install of Ubuntu. I still have the same problem. My wireless connection is still much slower when using Ubuntu than when using Windows 7. I am not sure what other info could help... EDIT: Ok, I have made live usb from the iso file I used to install Ubuntu on this pc, and ran it on my laptop. Still the same problem. However la[top works grand on cable. I suppose this means that my wireless adapter or network driver can be eliminated as root of the problem.. So maybe to do with router itself? I use ZyXEL P-660HW-D1

    Read the article

  • OBIEE 11.1.1 - OBIEE 11g Full Sample App on VMware Player 4

    - by user809526
    The Full Sample App is designed to run on Virtual Box. Let's describe how to run it on VMware Player 4. Open Virtualization Format Tool http://communities.vmware.com/community/vmtn/server/vsphere/automationtools/ovf VMware Player Documentation https://www.vmware.com/support/pubs/player_pubs.html Full Sample App Deployment Guide sampleapp107-vbimage-deployguide-453583.pdf INSTALL VMplayer 4.0.0 as root LINUX # sh VMware-Player-4.0.0-471780.x86_64.bundle (A new VM is not needed and can be deleted later after that installation is completed. "I will install OS later" - blank hard disk Guest: linux, Red Hat Enterprise Linux 5-64bits => rename to RHEL target: eg /a/root/vmware/ Max disk size: 5 GB (will be deleted) Disk: Single file Dummy RHEL.vmk, RHEL.vmdk is generated. "Delete VM from Disk" in VM Player.) Copy Full Sample App files to target /a/root/vmware/ WARNING: Select a target eg /a/root/vmware/ with lots of free space, 95 GB. Check checksums (md5sum). Please do it! ff85c7eacf7fb8c382e98da875e879e1  Sampleapp_v107_GA-disk1.vmdk 973258cb3c7d64ab03ae853278cf2233  Sampleapp_v107_GA-disk2.vmdk e576be16e36d810479736bfb15d050f5  Sampleapp_v107_GA-disk3.vmdk 3455df77279e53e07d5fee6712f1597d  Sampleapp_v107_GA-disk4.vmdk OVF FILE   Sampleapp_v107_GA.ovf CONVERSION $ cd /a/root/vmware/ LINUX $ /usr/bin/ovftool -tt=ovf --compress=1 -dm=monolithicSparse Sampleapp_v107_GA.ovf .  [dot] Opening OVF source: Sampleapp_v107_GA.ovf Warning: No manifest file Opening OVF target: . Writing OVF package: Sampleapp_v107_GA/Sampleapp_v107_GA.ovf Disk Transfer Completed                   Completed successfully WINDOWS CYGWIN $ /cygdrive/c/VMwarePlayer/OVFTool/ovftool.exe -tt=ovf --compress=1 -dm=monolithicSparse Sampleapp_v107_GA.ovf .  [dot] Opening OVF source: Sampleapp_v107_GA.ovf Warning: No manifest file Opening OVF target: . Writing OVF package: Sampleapp_v107_GA\Sampleapp_v107_GA.ovf Disk Transfer Completed Completed successfully /a/root/vmware$ du -sk 49095328    .   [50 GB already occupied] IMPORT - First start of VM Player 4: /usr/bin/vmplayer "Open a Virtual Machine" Browse to /a/root/vmware/Sampleapp_v107_GA/Sampleapp_v107_GA.ovf [the new generated .ovf] "Import Virtual Machine" dialog Name: Sampleapp_v107_GA Location: /a/root/vmware/Sampleapp_v107_GA/storage [was /home/tdubois/vmware/Sampleapp_v107_GA] "Import" "The import failed because /a/root/vmware/Sampleapp_v107_GA/Sampleapp_v107_GA.ovf did not pass OVF specification conformance or virtual hardware compliance checks. Click Retry to relax OVF specification..." "Retry" ; Long import /a/root/vmware/Sampleapp_v107_GA/storage/Sampleapp_v107_GA.vmx and new .vmdk files are created. /a/root/vmware$ du -sk 95551384    .   [95 GB occupied] Full Sample App GUEST SETUP "Edit VM settings" min 3GB, 2+ processors, network bridged. For OBIEE + Essbase testing use 8 GB RAM hardware. At first time lauch of Full Sample App, leave OEL booting for several minutes undisturbed. Problem with X display server may occur [/usr/bin/Xorg ; man Xorg]. "Failed to start the X server.... Would you like to view the X server output to diagnose the problem?" "No" [tab key] "Would you like to try to configure the X server? Note that you will need the root password for this." "Yes" [oracle] X Display Settings 800x600 saved in /etc/X11/xorg.conf "Trying to restart the X server" Login as root/oracle in guest OEL. In guest OEL, Virtual Machine > Install VMware Tools... Extract archive VMwareTools-8.8.0-471268.tar.gz all files in writable local directory eg /root In Terminal run Perl script # cd /root/vmware-tools-distrib ; ./vmware-install.pl [keep all default answers] Set keyboard layout System > Preferences > Keyboard > Layouts Restart X server eg System > Log Out root... , relogin Modify X resolution System > Preferences > Screen Resolution Full Sample App OEL login: oracle/oracle ; root/oracle [default US keyboard layout] Credentials are described in the 'sampleapp107-vbimage-deployguide-453583.pdf' The large files in /a/root/vmware/ /a/root/vmware/Sampleapp_v107_GA/ may be removed. FAILURE REMARK: Adding the 4 original Sampleapp_v107_GA-disks[1234].vmdk to VM Player does NOT work as described below. "Edit VM settings" "Remove" "Hard Disk" "Edit VM settings" "Add" "Hard Disk" "Next" "Use an existing virtual disk" "Browse" "Finish" "Keep existing format" "Ok" for each 4 disks settings one by one. Start VM Player 4. "You do not have write access to a partition" Allow all Sampleapp_v107 OEL linux launches. OEL stalls silently after 'Checking filesystems'.

    Read the article

  • Recover that Photo, Picture or File You Deleted Accidentally

    - by The Geek
    Have you ever accidentally deleted a photo on your camera, computer, USB drive, or anywhere else? What you might not know is that you can usually restore those pictures—even from your camera’s memory stick. Windows tries to prevent you from making a big mistake by providing the Recycle Bin, where deleted files hang around for a while—but unfortunately it doesn’t work for external USB drives, USB flash drives, memory sticks, or mapped drives. The great news is that this technique also works if you accidentally deleted the photo… from the camera itself. That’s what happened to me, and prompted writing this article. Restore that File or Photo using Recuva The first piece of software that you’ll want to try is called Recuva, and it’s extremely easy to use—just make sure when you are installing it, that you don’t accidentally install that stupid Yahoo! toolbar that nobody wants. Now that you’ve installed the software, and avoided an awful toolbar installation, launch the Recuva wizard and let’s start through the process of recovering those pictures you shouldn’t have deleted. The first step on the wizard page will let you tell Recuva to only search for a specific type of file, which can save a lot of time while searching, and make it easier to find what you are looking for. Next you’ll need to specify where the file was, which will obviously be up to wherever you deleted it from. Since I deleted mine from my camera’s SD card, that’s where I’m looking for it. The next page will ask you whether you want to do a Deep Scan. My recommendation is to not select this for the first scan, because usually the quick scan can find it. You can always go back and run a deep scan a second time. And now, you’ll see all of the pictures deleted from your drive, memory stick, SD card, or wherever you searched. Looks like what happened in Vegas didn’t stay in Vegas after all… If there are a really large number of results, and you know exactly when the file was created or modified, you can switch to the advanced view, where you can sort by the last modified time. This can help speed up the process quite a bit, so you don’t have to look through quite as many files. At this point, you can right-click on any filename, and choose to Recover it, and then save the files elsewhere on your drive. Awesome! Restore that File or Photo using DiskDigger If you don’t have any luck with Recuva, you can always try out DiskDigger, another excellent piece of software. I’ve tested both of these applications very thoroughly, and found that neither of them will always find the same files, so it’s best to have both of them in your toolkit. Note that DiskDigger doesn’t require installation, making it a really great tool to throw on your PC repair Flash drive. Start off by choosing the drive you want to recover from…   Now you can choose whether to do a deep scan, or a really deep scan. Just like with Recuva, you’ll probably want to select the first one first. I’ve also had much better luck with the regular scan, rather than the “dig deeper” one. If you do choose the “dig deeper” one, you’ll be able to select exactly which types of files you are looking for, though again, you should use the regular scan first. Once you’ve come up with the results, you can click on the items on the left-hand side, and see a preview on the right.  You can select one or more files, and choose to restore them. It’s pretty simple! Download DiskDigger from dmitrybrant.com Download Recuva from piriform.com Good luck recovering your deleted files! And keep in mind, DiskDigger is a totally free donationware software from a single, helpful guy… so if his software helps you recover a photo you never thought you’d see again, you might want to think about throwing him a dollar or two. Similar Articles Productive Geek Tips Stupid Geek Tricks: Undo an Accidental Move or Delete With a Keyboard ShortcutRestore Accidentally Deleted Files with RecuvaCustomize Your Welcome Picture Choices in Windows VistaAutomatically Resize Picture Attachments in Outlook 2007Resize Your Photos with Easy Thumbnails TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Icelandic Volcano Webcams Open Multiple Links At One Go NachoFoto Searches Images in Real-time Office 2010 Product Guides Google Maps Place marks – Pizza, Guns or Strip Clubs Monitor Applications With Kiwi

    Read the article

  • Wireless Problem on Acer Aspire 5610z

    - by Ugur Can Yalaki
    I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

    Read the article

  • Can't get LWJGL lighting to work

    - by Zarkonnen
    I'm trying to enable lighting in lwjgl according to the method described by NeHe and this post. However, no matter what I try, all faces of my shapes always receive the same amount of light, or, in the case of a spinning shape, the amount of lighting seems to oscillate. All faces are lit up by the same amount, which changes as the pyramid rotates. Concrete example (apologies for the length): Note how all panels are always the same brightness, but the brightness varies with the pyramid's rotation. This is using lwjgl 2.8.3 on Mac OS X. package com; import com.zarkonnen.lwjgltest.Main; import org.lwjgl.opengl.Display; import org.lwjgl.opengl.DisplayMode; import org.lwjgl.opengl.GL11; import org.newdawn.slick.opengl.Texture; import org.newdawn.slick.opengl.TextureLoader; import org.lwjgl.util.glu.*; import org.lwjgl.input.Keyboard; import java.nio.FloatBuffer; import java.nio.ByteBuffer; import java.nio.ByteOrder; /** * * @author penguin */ public class main { public static void main(String[] args) { try { Display.setDisplayMode(new DisplayMode(800, 600)); Display.setTitle("3D Pyramid"); Display.create(); } catch (Exception e) { } initGL(); float rtri = 0.0f; Texture texture = null; try { texture = TextureLoader.getTexture("png", Main.class.getResourceAsStream("tex.png")); } catch (Exception ex) { ex.printStackTrace(); } while (!Display.isCloseRequested()) { // Draw a Triangle :D GL11.glClear(GL11.GL_COLOR_BUFFER_BIT | GL11.GL_DEPTH_BUFFER_BIT); GL11.glLoadIdentity(); GL11.glTranslatef(0.0f, 0.0f, -10.0f); GL11.glRotatef(rtri, 0.0f, 1.0f, 0.0f); texture.bind(); GL11.glBegin(GL11.GL_TRIANGLES); GL11.glTexCoord2f(0.0f, 1.0f); GL11.glVertex3f(0.0f, 1.0f, 0.0f); GL11.glTexCoord2f(-1.0f, -1.0f); GL11.glVertex3f(-1.0f, -1.0f, 1.0f); GL11.glTexCoord2f(1.0f, -1.0f); GL11.glVertex3f(1.0f, -1.0f, 1.0f); GL11.glTexCoord2f(0.0f, 1.0f); GL11.glVertex3f(0.0f, 1.0f, 0.0f); GL11.glTexCoord2f(-1.0f, -1.0f); GL11.glVertex3f(1.0f, -1.0f, 1.0f); GL11.glTexCoord2f(1.0f, -1.0f); GL11.glVertex3f(1.0f, -1.0f, -1.0f); GL11.glTexCoord2f(0.0f, 1.0f); GL11.glVertex3f(0.0f, 1.0f, 0.0f); GL11.glTexCoord2f(-1.0f, -1.0f); GL11.glVertex3f(-1.0f, -1.0f, -1.0f); GL11.glTexCoord2f(1.0f, -1.0f); GL11.glVertex3f(1.0f, -1.0f, -1.0f); GL11.glTexCoord2f(0.0f, 1.0f); GL11.glVertex3f(0.0f, 1.0f, 0.0f); GL11.glTexCoord2f(-1.0f, -1.0f); GL11.glVertex3f(-1.0f, -1.0f, -1.0f); GL11.glTexCoord2f(1.0f, -1.0f); GL11.glVertex3f(-1.0f, -1.0f, 1.0f); GL11.glEnd(); GL11.glBegin(GL11.GL_QUADS); GL11.glVertex3f(1.0f, -1.0f, 1.0f); GL11.glVertex3f(1.0f, -1.0f, -1.0f); GL11.glVertex3f(-1.0f, -1.0f, -1.0f); GL11.glVertex3f(-1.0f, -1.0f, 1.0f); GL11.glEnd(); Display.update(); rtri += 0.05f; // Exit-Key = ESC boolean exitPressed = Keyboard.isKeyDown(Keyboard.KEY_ESCAPE); if (exitPressed) { System.out.println("Escape was pressed!"); Display.destroy(); } } Display.destroy(); } private static void initGL() { GL11.glEnable(GL11.GL_LIGHTING); GL11.glMatrixMode(GL11.GL_PROJECTION); GL11.glLoadIdentity(); GLU.gluPerspective(45.0f, ((float) 800) / ((float) 600), 0.1f, 100.0f); GL11.glMatrixMode(GL11.GL_MODELVIEW); GL11.glLoadIdentity(); GL11.glEnable(GL11.GL_TEXTURE_2D); GL11.glShadeModel(GL11.GL_SMOOTH); GL11.glClearColor(0.0f, 0.0f, 0.0f, 0.0f); GL11.glClearDepth(1.0f); GL11.glEnable(GL11.GL_DEPTH_TEST); GL11.glDepthFunc(GL11.GL_LEQUAL); GL11.glHint(GL11.GL_PERSPECTIVE_CORRECTION_HINT, GL11.GL_NICEST); float lightAmbient[] = {0.5f, 0.5f, 0.5f, 1.0f}; // Ambient Light Values float lightDiffuse[] = {1.0f, 1.0f, 1.0f, 1.0f}; // Diffuse Light Values float lightPosition[] = {0.0f, 0.0f, 2.0f, 1.0f}; // Light Position ByteBuffer temp = ByteBuffer.allocateDirect(16); temp.order(ByteOrder.nativeOrder()); GL11.glLight(GL11.GL_LIGHT1, GL11.GL_AMBIENT, (FloatBuffer) temp.asFloatBuffer().put(lightAmbient).flip()); // Setup The Ambient Light GL11.glLight(GL11.GL_LIGHT1, GL11.GL_DIFFUSE, (FloatBuffer) temp.asFloatBuffer().put(lightDiffuse).flip()); // Setup The Diffuse Light GL11.glLight(GL11.GL_LIGHT1, GL11.GL_POSITION, (FloatBuffer) temp.asFloatBuffer().put(lightPosition).flip()); // Position The Light GL11.glEnable(GL11.GL_LIGHT1); // Enable Light One } }

    Read the article

  • Session Report - Java on the Raspberry Pi

    - by Janice J. Heiss
    On mid-day Wednesday, the always colorful Oracle Evangelist Simon Ritter demonstrated Java on the Raspberry Pi at his session, “Do You Like Coffee with Your Dessert?”. The Raspberry Pi consists of a credit card-sized single-board computer developed in the UK with the intention of stimulating the teaching of basic computer science in schools. “I don't think there is a single feature that makes the Raspberry Pi significant,” observed Ritter, “but a combination of things really makes it stand out. First, it's $35 for what is effectively a completely usable computer. You do have to add a power supply, SD card for storage and maybe a screen, keyboard and mouse, but this is still way cheaper than a typical PC. The choice of an ARM (Advanced RISC Machine and Acorn RISC Machine) processor is noteworthy, because it avoids problems like cooling (no heat sink or fan) and can use a USB power brick. When you add in the enormous community support, it offers a great platform for teaching everyone about computing.”Some 200 enthusiastic attendees were present at the session which had the feel of Simon Ritter sharing a fun toy with friends. The main point of the session was to show what Oracle was doing to support Java on the Raspberry Pi in a way that is entertaining and fun. Ritter pointed out that, in addition to being great for teaching, it’s an excellent introduction to the ARM architecture, and runs well with Java and will get better once it has official hard float support. The possibilities are vast.Ritter explained that the Raspberry Pi Project started in 2006 with the goal of devising a computer to inspire children; it drew inspiration from the BBC Micro literacy project of 1981 that produced a series of microcomputers created by the Acorn Computer company. It was officially launched on February 29, 2012, with a first production of 10,000 boards. There were 100,000 pre-orders in one day; currently about 4,000 boards are produced a day. Ritter described the specification as follows:* CPU: ARM 11 core running at 700MHz Broadcom SoC package Can now be overclocked to 1GHz (without breaking the warranty!) * Memory: 256Mb* I/O: HDMI and composite video 2 x USB ports (Model B only) Ethernet (Model B only) Header pins for GPIO, UART, SPI and I2C He took attendees through a brief history of ARM Architecture:* Acorn BBC Micro (6502 based) Not powerful enough for Acorn’s plans for a business computer * Berkeley RISC Project UNIX kernel only used 30% of instruction set of Motorola 68000 More registers, less instructions (Register windows) One chip architecture to come from this was… SPARC * Acorn RISC Machine (ARM) 32-bit data, 26-bit address space, 27 registers First machine was Acorn Archimedes * Spin off from Acorn, Advanced RISC MachinesNext he presented its features:* 32-bit RISC Architecture–  ARM accounts for 75% of embedded 32-bit CPUs today– 6.1 Billion chips sold last year (zero manufactured by ARM)* Abstract architecture and microprocessor core designs– Raspberry Pi is ARM11 using ARMv6 instruction set* Low power consumption– Good for mobile devices– Raspberry Pi can be powered from 700mA 5V only PSU– Raspberry Pi does not require heatsink or fanHe described the current ARM Technology:* ARMv6– ARM 11, ARM Cortex-M* ARMv7– ARM Cortex-A, ARM Cortex-M, ARM Cortex-R* ARMv8 (Announced)– Will support 64-bit data and addressingHe next gave the Java Specifics for ARM: Floating point operations* Despite being an ARMv6 processor it does include an FPU– FPU only became standard as of ARMv7* FPU (Hard Float, or HF) is much faster than a software library* Linux distros and Oracle JVM for ARM assume no HF on ARMv6– Need special build of both– Raspbian distro build now available– Oracle JVM is in the works, release date TBDNot So RISCPerformance Improvements* DSP Enhancements* Jazelle* Thumb / Thumb2 / ThumbEE* Floating Point (VFP)* NEON* Security Enhancements (TrustZone)He spent a few minutes going over the challenges of using Java on the Raspberry Pi and covered:* Sound* Vision * Serial (TTL UART)* USB* GPIOTo implement sound with Java he pointed out:* Sound drivers are now included in new distros* Java Sound API– Remember to add audio to user’s groups– Some bits work, others not so much* Playing (the right format) WAV file works* Using MIDI hangs trying to open a synthesizer* FreeTTS text-to-speech– Should work once sound works properlyHe turned to JavaFX on the Raspberry Pi:* Currently internal builds only– Will be released as technology preview soon* Work involves optimal implementation of Prism graphics engine– X11?* Once the JavaFX implementation is completed there will be little of concern to developers-- It’s just Java (WORA). He explained the basis of the Serial Port:* UART provides TTL level signals (3.3V)* RS-232 uses 12V signals* Use MAX3232 chip to convert* Use this for access to serial consoleHe summarized his key points. The Raspberry Pi is a very cool (and cheap) computer that is great for teaching, a great introduction to ARM that works very well with Java and will work better in the future. The opportunities are limitless. For further info, check out, Raspberry Pi User Guide by Eben Upton and Gareth Halfacree. From there, Ritter tried out several fun demos, some of which worked better than others, but all of which were greeted with considerable enthusiasm and support and good humor (even when he ran into some glitches).  All in all, this was a fun and lively session.

    Read the article

  • Example of UITextField ResignFirstResponder with Monotouch

    - by kentakhy
    I'm a newbie. I can't figure out how and where to call ResignFirstResponder to get rid of the keyboard when the user finished entering the text in an UITextField. I'm a bit confused by the UIResponder class. Mono documentation says: "To dismiss the keyboard, send the UIResponder.ResignFirstResponder message to the text field that is currently the first responder." How to do so? Can someone post a simple working example? There are many examples in Obj-C but none in C#. Many thanks.

    Read the article

  • How to get select's value in jqGrid when using <select> editoptions on a column

    - by destroyer of evil
    I have a couple of columns in jqGrid with edittype="select". How can I read the option value of the value currently selected in a particular row? e.g.: When I provide the following option, how do I get "FE" for FedEx, etc. editoption: { value: “FE:FedEx; IN:InTime; TN:TNT” } getRowData() for the rowId/cellname returns only the text/displayed component of the select. If I set a "change" data event on the column, the underlying fires change events only on mouse clicks, and not keyboard selects (there's numerous references to generic selects and mouse/keyboard issues). Bottomline, when a new value is selected, I need to know the option value at the time of the change, and also prior to posting to the server.

    Read the article

  • Confluence or apache on win server 2008 cant find scripts and images :(

    - by Ishak
    I am a newbie to both Tomcat and Apache. I have set the virtual hosts as described in Here. And JIRA works fine when i browse the URL jira.agmlab.com. However when i try to access Confluence(3.4.5) with confluence.agmlab.com the pages come in plain html, i can login and browse pages but there is no css or js so that my confluence pages look very ugly. what can possibly cause this and how to fix this? here is my virtual hosts definitions : # # Virtual Hosts # # If you want to maintain multiple domains/hostnames on your # machine you can setup VirtualHost containers for them. Most configurations # use only name-based virtual hosts so the server doesn't need to worry about # IP addresses. This is indicated by the asterisks in the directives below. # # Please see the documentation at # <URL:http://httpd.apache.org/docs/2.2/vhosts/> # for further details before you try to setup virtual hosts. # # You may use the command line option '-S' to verify your virtual host # configuration. # # Use name-based virtual hosting. # NameVirtualHost * # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for all requests that do not # match a ServerName or ServerAlias in any <VirtualHost> block. # <VirtualHost *> ServerName confluence.agmlab.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8081/confluence/ ProxyPassReverse / http://localhost:8081/confluence/ # ProxyHTMLURLMap /confluence/ / <Location /> Order allow,deny Allow from all </Location> </VirtualHost> <VirtualHost *> ServerName jira.agmlab.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8080/ ProxyPassReverse / http://localhost:8080/ <Location /> Order allow,deny Allow from all </Location> </VirtualHost> and i added 127.0.0.1 jira.agmlab.com 127.0.0.1 confluence.agmlab.com to my hosts file (i am using Win Server 2008 OS). here is part of the error log from Apache access.log file : 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/1.0/_/download/resources/confluence.web.resources:aui-forms/confluence-forms.css HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/3.4.5/_/download/batch/com.atlassian.confluence.keyboardshortcuts:confluence-keyboard-shortcuts/com.atlassian.confluence.keyboardshortcuts:confluence-keyboard-shortcuts.css HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/0.7/_/download/batch/com.atlassian.plugins.shortcuts.atlassian-shortcuts-module:shortcuts/com.atlassian.plugins.shortcuts.atlassian-shortcuts-module:shortcuts.css HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/1/_/download/superbatch/js/batch.js HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/1.0/_/download/batch/confluence.web.resources:login/confluence.web.resources:login.js HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/1/_/download/superbatch/css/batch.css?media=print HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/1/_/styles/combined.css HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/1.2.2/_/download/batch/com.atlassian.confluence.plugins.doctheme:splitter/com.atlassian.confluence.plugins.doctheme:splitter.js HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/1.0/_/download/batch/legacy.confluence.web.resources:prototype/legacy.confluence.web.resources:prototype.js HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/0.7/_/download/batch/com.atlassian.plugins.shortcuts.atlassian-shortcuts-module:shortcuts/com.atlassian.plugins.shortcuts.atlassian-shortcuts-module:shortcuts.js HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/3.4.5/_/download/batch/com.atlassian.confluence.keyboardshortcuts:confluence-keyboard-shortcuts/com.atlassian.confluence.keyboardshortcuts:confluence-keyboard-shortcuts.js HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/images/logo/confluence_48_white.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/opensearch/osd.action HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:13:34 +0200] "GET /confluence/s/2035/1/_/images/logo/confluence_16.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:16:27 +0200] "POST /plugins/servlet/gadgets/security-tokens HTTP/1.1" 200 525 127.0.0.1 - - [03/Jan/2011:16:19:08 +0200] "GET /confluence/favicon.ico HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:08 +0200] "GET /confluence/s/2035/1/_/images/logo/confluence_16.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:08 +0200] "GET /confluence/s/2035/1/_/images/icons/profilepics/anonymous.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:08 +0200] "GET /confluence/images/logo/confluence_48_white.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:08 +0200] "GET /confluence/images/icons/star_grey.gif HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:08 +0200] "GET /confluence/s/2035/1/_/images/icons/add_12.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:08 +0200] "GET /confluence/images/border/spacer.gif HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:11 +0200] "GET /confluence/favicon.ico HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:11 +0200] "GET /confluence/s/2035/1/_/images/logo/confluence_16.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:12 +0200] "GET /confluence/s/2035/1/_/images/icons/add_12.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:12 +0200] "GET /confluence/s/2035/1/_/images/icons/profilepics/anonymous.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:12 +0200] "GET /confluence/images/logo/confluence_48_white.png HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:12 +0200] "GET /confluence/images/border/spacer.gif HTTP/1.1" 404 2788 127.0.0.1 - - [03/Jan/2011:16:19:12 +0200] "GET /confluence/images/icons/star_grey.gif HTTP/1.1" 404 2788 I can see the pages properly with js and css and images when i use confluence with URL localhost:8081/confluence. i have just set the base url of confluence to "confluence.agmlab.com" and then restarted both confluence and apache but nothing changed, and i also checked settings for jira, and its base URL is localhost:8080 but it works fine. Can it be something related with the permissions defined in Win Server 2008 ? maybe there is not enough rights (such as read execute ) in some users, directories ??

    Read the article

  • ergonomics: what's better; trackball, ergonomic mouse or some other pointing device (a-la touchscree

    - by mauriciopastrana
    So I bit into the hype and recently purchased an apple wireless keyboard and that evil bar-of-soap thing apple makes for a mouse. Couple of hundred dollars later and this is where I begin to worry about RSI. Go figure. Don't get me wrong, this apple mouse is genius and looks pretty as hell, but my right wrist feels tired after a full day's worth of work, so i'm thinking of switching. Anyone out there use a trackball? is this worse? should I get a super-ergonomic mouse instead? I've seen mouse-trackball combos but am not sold, they still elicit the same end-finger behaviour detrimental for RSI, right? I also have a wrist-rest mousepad, but couldn't find one suitable for my keyboard. I've even considered having a small touchscreen where the mousepad should go, no mouse (or alternatively, a usb trackpad). Just looking for ideas, is the trackball better than the mouse? /mp

    Read the article

  • Focus In An ItemsControl

    - by Andrew
    I have an ItemsControl that uses a DataTemplate. The DataTemplate contains a TextBox, which can receive keyboard focus. I need to be able to move the keyboard focus from the currently focused TextBox in the DataTemplate to the next TextBox, as if the Tab key has been pressed. I've noticed that there is a UIElement.MoveFocus() method, but this begs the question as to which UIElement should be used to call the method. This is probably the reason why I haven't gotten this method to work for me... Any help would be really appreciated! Thanks, Andrew

    Read the article

  • Bring to front DatePicker on an UITextField

    - by crazyfr
    Hi, When an UITextField is firstResponder, I would like to bring to front an UIDatePicker (bottom part of the screen) without the "going down keyboard" (no call to UITextField resignFirstResponder). The aim is to process like UIKeyboard of UITextField which pop-up on nearly everything when it becomeFirstResponder. modalViewController seems to be fullscreen only. - showDatePicker:(id)sender { if([taskName isFirstResponder]) [taskName resignFirstResponder]; [self.view.window addSubview: self.pickerView]; // size up the picker view and compute the start/end frame origin (...) [UIView commitAnimations]; } This example is an animation of keyboard going down, and DatePicker going up, behind and not in front. Do you know a solution ? A piece of code would be welcome. Thanks in advance.

    Read the article

  • Type attribute for text_field

    - by Koning Baard XIV
    I have this code: <%= f.text_field :email, :type => "email", :placeholder => "[email protected]" %> So people can enter their email on an iPhone with the email keyboard instead of the ASCII keyboard. However, the output is: <input id="user_email" name="user[email]" placeholder="[email protected]" size="30" type="text" /> which should be: <input id="user_email" name="user[email]" placeholder="[email protected]" size="30" type="email" /> Is there a way to force Rails to use the email type instead of text, or must I use HTML directly? Thanks

    Read the article

  • How is the iPhone SMS compose view implemented?

    - by erotsppa
    Regarding the SMS compose view as show in the picture below: I have two questions: 1) How is the text entry box implemented? There are no standard control from the API and the box is smart enough to resize when you press enter OR when the text is too long. Also the bar resizes with it. How is this done with the least coding? 2) How to code it such that when the keyboard shows up the whole view shifts up? Typically when the keyboard shows, it goes over your current view.

    Read the article

< Previous Page | 227 228 229 230 231 232 233 234 235 236 237 238  | Next Page >