Search Results

Search found 18699 results on 748 pages for 'laptop mode'.

Page 236/748 | < Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >

  • How can I run Ghost from a bootable USB key drive?

    - by Joe Philllips
    I have a laptop that does not have a cd-rom or floppy drive. It is able to boot from USB though. I have a disk image (ghost) of the disk that I need to restore back onto the laptop. I can't find a way to actually run the Ghost utility from a USB key though. I believe the ghost.exe should run from within DOS just fine but I can't seem to create a bootable USB key with DOS on it that allows me to run an EXE. Edit: I managed to find a Ghost utility that I could load from a bootable USB drive. Unfortunately, when I plug in my NTFS external drive (USB), it is not detected.

    Read the article

  • Increasing the screen resolution in Ubuntu 10.04

    - by Veera
    I'm running Ubuntu 10.04 edition on my Acer 5738Z laptop. The screen size of my laptop is about 15'' but the screen resolution in Ubuntu is stuck at 1366x768. I know that my monitor could give better resolution, because previously I was running Win XP and I was able to set higher resolution there. So, my questions here: How do I increase my screen resolution, here? As per the answer given to a related question, I tried to edit the xorg.conf file, but I couldn't find the file in the place /etc/x11/. Should I create this file? If I have to install screen drivers separately, where could I find it?

    Read the article

  • nvidia twinview in ubuntu with large resolutions not working

    - by knittl
    i bought an external monitor and can't get it to work properly with my laptop screen. my laptop screen has a resolution of 1920x1200 and the new monitor has 1920x1080 when i open nvidia-settings and select the maximum resolution for each of the screen, one screen will always stay blank. if i select a smaller resolution for one of the two it will work. 1920x1200 + 1440x900 = works 1680x1050 + 1920x1080 = works 1920x1200 + 1920x1080 = doesn't work (but that's what i want to have!) my graphics card is an 01:00.0 VGA compatible controller: nVidia Corporation Quadro FX 360M (rev a1) (output from lspci), driver is proprietary nvidia driver, operating system is ubuntu. any help greatly apreciated

    Read the article

  • Mac OS X: pushing all traffic through a VMWare VM

    - by bj99
    I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

    Read the article

  • What cable to connect Inspiron 1720 to HDMI TV?

    - by Bernhard Hofmann
    Hi I'm a little confused to say the least when it comes to video formats and protocols. I'd like to view my laptop output on my HD TV. The TV has HDMI, S-Video, and RCA inputs. My laptop has a VGA female port on the side for driving a 2nd monitor, and an S-VHS output at the back. No, it has no DVI, which I've heard is a poor decision from DELL, and even poorer decision on my part to buy it. Can I get true HD output from this to my TV? What cable do I need, or would I need a converter? Any other suggestions are also welcome, such as how to get something close to HD on my TV. Thanks! Bernhard

    Read the article

  • Sony Bravia KDL-32L5000 PC resolution slightly off

    - by user18818
    I have a PC running two Nvidia 8500 GTs in SLI mode and I am trying to use my TV in dual mode. When I switch the TV to PC the screen is nearly centered with a slight offset. All resolutions are effected from 800x600 all the way up to the TVs native 1360x768. I have tried with SLI on and off and have PhysX turned off as well as I thought that might have an effect. I am running Windows XP 64-bit SP2 DirectX ver 9.0c Nvidia driver version 181.22 Any other information please let me know. Thanks in advance.

    Read the article

  • Safe BIOS upgrade run from external USB-HDD and not native OS

    - by ecoologic
    I have a Toshiba M200 laptop which came with Windows Vista. After buying it, I replaced the OS with XP and recently I swapped the internal hard disk with a bigger one where I only have Ubuntu. So now I can boot XP from the external USB hard disk. There's a BIOS update available (2.3 against my 1.8) which I'd like to install and there's also a version for XP. Is it "reasonably" safe to install this upgrade for Windows XP (despite the original OS was Vista, the laptop model is the right one) from my external USB hard disk with Win XP?

    Read the article

  • Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

    - by blaineh
    I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

    Read the article

  • No sound through DisplayPort

    - by Chris Koknat
    I'm trying to connect my Elitebook 8440p laptop to my Samsung HDTV. The laptop does not have a HDMI connection, but it does have DisplayPort. I bought a DisplayPort-to-HDMI adapter here http://www.amazon.com/gp/product/B002CSRFD8/ref=oss_product, and connected it with a 3' HDMI cable. The video shows up fine, but there is no audio. DisplayPort, HDMI, and the adapter all support audio. I contacted HP tech support, who told me to update my sound drivers. I installed the driver and rebooted. Supposedly, I should see a "HD Audio" tab. No luck, even after installing the driver again and rebooting. HP closed the case. I'm using XP Pro.

    Read the article

  • Can I tell which installation DVD was used for my Windows XP?

    - by Den
    I have two Windows XP installation DVDs (that came from the OEM with my two laptops). I need to reinstall Windows on one of them but I'm not sure which one is which. Is there any way to tell which DVD was used for each laptop? PS. They both came from the same OEM and there're no distinguishing markings on the DVDs themselves. PS2. The reason for my concern is to avoid installation twice, which may invalidate license for already installed Windows XP on one laptop if I duplicate it to another.

    Read the article

  • rdesktop + seamlessrdp + virtualbox slow on Windows

    - by Claudiu
    I'm trying to get VirtualBox seamless mode to work on all of my monitors at once. I was directed to this link, so I followed the instructions, using the windows port of rdesktop 1.6 found here, and using Xming as an X server. I eventually finally got it to work! However, it's really slow. While VirtualBox's regular seamless mode is as performant as if I was running apps on my host machine, with rdesktop it takes 1-2 seconds to register any user input. Dragging windows around is laggy and buggy (pieces of the desktop behind the window show through). I'm simply connecting to localhost, so network bandwidth/latency shouldn't be an issue... anyone have any idea why it's so slow and what I can do to make it more performant?

    Read the article

  • ATI Catalyst setting to stretch Windows XP start bar across both displays

    - by scunliffe
    I have a Lenovo T400 laptop with an ATI Mobility Radeon HD 3400 Series video card, using the ATI Catalyst Control Center to span my Windows XP display over the laptop display and a Dell flatpanel LCD. This works fine, but I'm used to NVIDIA multi-desktop that let me control the "Start bar" to either exist on only 1 screen... be duplicated on both, or (what I want), stretched across both. Is this possible with the ATI card/Catalyst Software? If not, are there any utilities out there that will handle this for me? That is, what I have: +----------+ +----------+ | | | | | Lenovo | | Dell | | (primary)| | | +----------+ | | |Start Tray| | | +----------+ +----------+ And this is what I want: +----------+ +----------+ | | | | | Lenovo | | Dell | | (primary)| | | +----------+ +----------+ |Start | | Tray| +----------+ +----------+

    Read the article

  • How to get external 2.5 inch HD enclosure get recognised

    - by fireBand
    I am completely out of ideas. I have 2.5inch HDD from my old laptop, I have tried with 2 different HDD enclosures but my desktop does not recognize it. Not even showing in the disk management or BIOS. The HDD works fine if I use in a 3.5 inch enclosure with external power. I have tried 3 different Y USB cables. I have also got a 7 port self powered 2A USB hub. I have updated my chipset drivers as well. The problem is with my desktop , the enclosures work fine with my new laptop. Anything else that I should try? Thanks in advance.

    Read the article

  • How to uninstall AMD Display Driver from other install of Windows

    - by nar
    So my Windows 7 had a BSOD from an Ati driver file then restarting only gives me some wierd coloured lines at the top of the screen. Starting in safe mode causes the boot up to freeze at AtiPcie.sys and overlays the same coloured lines on the safe mode start up display. It seems to be a problem with the display driver but I can't get into the OS at all to uninstall it. Luckily I have an old install of Windows 7 from when I moved to a SSD still on my HDD and that runs just fine so I'm pretty sure its a software problem (Maybe the SSD corrupted a driver file or something). So does anyone know how I can uninstall the driver files from another Windows 7 install on the same PC? EDIT: What I mean is, I'm running on the broken PC right now but using a different HDD's windows install. I have full access to the not booting up OS drive with the Windows so I can delete any files/load the registry etc...

    Read the article

  • How to proxy and encrypt all my internet traffic with Win7 and Win2008R2?

    - by Malartre
    Hi, I have a Windows 7 laptop and a Windows 2008 R2 server. How can I encrypt and route all my internet request from the Win7 laptop to the Win2008R2 server? I guess the server would be called a proxy? Goal is to prevent unencrypted network snooping. I found this article about using SSH, but I would prefer an official windows integrated solution. What's the Microsoft "way" on this? http://lifehacker.com/237227/geek-to-live--encrypt-your-web-browsing-session-with-an-ssh-socks-proxy I would like this to work for all internet traffic, not just browser traffic and I would like to set this up on many Win7 clients. Carl

    Read the article

  • use of Lsh and Rsh keys in windows 7 calculator

    - by Tom
    Does anyone know the function of the Lsh and Rsh keys in Windows 7 calculator when it is in Programmer's mode. One would think it's meant to shift bits left and right, but that doesn't seem to happen: sometimes nothing happens, other times I get a 'Result not defined' message in the display. Has anyone figured it out yet, is this a known bug? While we're at it, does anyone have suggestions for a good calculator, one with a decent reference guide / user guide (windows help doesn't seem to give any hints on what any of the keys do, in any mode).

    Read the article

  • Function key emulator for Dell inspiron 6400 on external keyboard

    - by hardik988
    I have a 3 year old Dell inspiron 6400 with windows 7 and ubuntu 9.10 dual boot. I messed up my Laptop keyboard and hence my Fn key is not working and I need it to activate the wireless whose activation combination is Fn+F2. Is there any way I can emulate the Fn key or get my wireless to start in windows or ubuntu ? My bios has an option for Fn key emulation but that only supports external PS/2 keyboards and my laptop doesn't have a ps/2 slot. Any ideas would be appreciated ..

    Read the article

  • Configuring htaccess to show authentication prompt only for subdomain

    - by Philipp Lenssen
    How do I write the htaccess so that it will only require authentication when on admin.example.com, but not on www.example.com (like by using some if-else clause)? Background: I have a site running in two modes: The admin mode should be reached at something like admin.example.com, whereas the normal mode would be www.example.com -- but both should point to the same directory & scripts within them (the scripts then turn on certain editing features by checking if the script is accessed from the admin subdomain). Edit: I can now see this has been asked and answered at StackOverflow, though I can't get the top answer to work for me...

    Read the article

  • Disadvantages of enabling AHCI after Win7 install

    - by Mario De Schaepmeester
    I've formatted my notebook that has a 5400RPM HDD with ~500GB capacity. After installing Windows 7 and about half the drivers (including chipset) I began to doubt whether to go for IDE or AHCI mode for my hard drive. There used to be a lot of discussion on the internet which is better and so far I understood it was particularly helpful on SSDs. Now the general consensus seems to be that AHCI mode is best for most hard drives. I have thus enabled AHCI in the middle of configuring my notebook (rest of the drivers, necessary software etc...) Two questions: considering my HDD's spec above, should I leave it on? Is there any disadvantage of enabling it after Windows 7 and chipset drivers installation? Windows 7 version is 64 bit Home Premium.

    Read the article

  • Older raid controllers in raid 5 vs. Jbod and SW raid

    - by TEB
    Hi. Im in the fortunate position to have 6 Supermicro older VOD servers with the following config: Supermicro 3U case, 3xPSU Dual Xeon 3ghz P4 class cpu (5 years old.. havnt checked the exact type) 4GB Ram 3ware 9500-8 SATA controller 8 SATA SLOTS and alot of free drives. 2GB FLASH Bootdrive What im curious about is the RAID5 performance on these old beasts in HW mode vs. SW on Linux with the controller set in JBOD mode. Im thinking on using Centos 5.5 or Ubuntu or ZFS RaidZ on Opensolaris. Any tips? or reccomendations ? best regards TEB

    Read the article

  • Cannot install wireless lan service on windows 2012 RTM offline

    - by user1763118
    I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

    Read the article

  • Missing disk space in Windows XP

    - by Jørn Schou-Rode
    On my mother's Lenovo laptop, Windows XP claims that the hard drive is almost full. According to the properties window, 52.7 out of 55.2 GB is in use: By deleting temp files from Internet Explorer, System Restore, Recycle bin, Windows Update, System Cleanup, I managed to free up about one GB. That's still 50 GB in use, which still is a lot more than I expected. Hence, I gave good old WinDirStat a spin, and here's the output: It might be hard to read here, but the first line says that the total amount of disk space in use on drive C is 24.3 GB. So Windows claims usage of 52.7 GB and WinDirStat can only account for 24.3 GB. Where is the other half of that disk space being used? I hope someone has an answer, or some tricks or tips to do further research. UPDATE: The laptop in question has an SSD hard drive. I am aware that these disk (at least the earlier ones) have a limited life-time. Could the symptoms described be caused by wear and tear on the SSD?

    Read the article

  • Why does my wifi fail to stay connected?

    - by Mark0978
    We have 5 different laptops in the house, 1 macbook, 1 Compaq, 3 dells, plus numerous little devices like ipods, squeezeboxs, squeezebox radios and controllers, you name it. All of them connect to and stay connected to the "downstairs" WIFI just fine. But my laptop (the most expensive of the lot) refuses to stay connected, preferring the much weaker and slower signal upstairs. My laptop is running Win7 (64 bit) Ultimate with an Intel 3945ABG WIFI contoller (It's a Dell Precision M6300). The WIFI Access Point is a Cisco WRT54G2 V1 with firmware: Firmware: DD-WRT v24-sp2 (10/10/09) micro Time: 11:11:10 up 42 min, load average: 0.06, 0.01, 0.00 WAN: Disabled

    Read the article

  • Increase the compression performance of VPN

    - by Martin
    I am currently switching from a system with HPN-SSH tunnels and enabled compression to something VPN based. I have tried tinc and n2n so far, hamachi requires a library I do not have. In my primitive benchmarks I am not satisfied with the achievable bandwidth compared to the SSH tunnels. In tinc the low LZO setting performed best, but compression is only available in UDP mode. Ideally I would like to have a TCP-based VPN with a multi-threaded compression. Can you suggest me some ideas how to increase the performance? Would it be possible to somehow put a compression filter in front of the tun interface? Or are there any VPN implementations that might be better suited for my needs (fast compression, TCP-based, switch mode, does not have to be super-secure)? I would consider tunnelling Ethernet over SSH, but according to some articles it is not advisable.

    Read the article

< Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >