Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 236/600 | < Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >

• DrayTek 2820 configuration using public IP addresses

  - by Kev

  I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

  Read the article

• Bridging Virtual Networking into Real LAN on a OpenNebula Cluster

  - by user101012

  I'm running Open Nebula with 1 Cluster Controller and 3 Nodes. I registered the nodes at the front-end controller and I can start an Ubuntu virtual machine on one of the nodes. However from my network I cannot ping the virtual machine. I am not quite sure if I have set up the virtual machine correctly. The Nodes all have a br0 interfaces which is bridged with eth0. The IP Address is in the 192.168.1.x range. The Template file I used for the vmnet is: NAME = "VM LAN" TYPE = RANGED BRIDGE = br0 # Replace br0 with the bridge interface from the cluster nodes NETWORK_ADDRESS = 192.168.1.128 # Replace with corresponding IP address NETWORK_SIZE = 126 NETMASK = 255.255.255.0 GATEWAY = 192.168.1.1 NS = 192.168.1.1 However, I cannot reach any of the virtual machines even though sunstone says that the virtual machine is running and onevm list also states that the vm is running. It might be helpful to know that we are using KVM as a hypervisor and I am not quite sure if the virbr0 interface which was automatically created when installing KVM might be a problem.

  Read the article

• MySQL remote access not working - Port Close?

  - by dave.zap

  I am not able to get a remote connection established to MySQL. From my pc I am able to telnet to 3306 on the existing server, but when I try the same with the new server it hangs for few minutes then returns # mysql -utest3 -h [server ip] -p Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on '[server ip]' (110) Here is some output from the server. # nmap -sT -O localhost -p 3306 ... PORT STATE SERVICE 3306/tcp closed mysql ... # netstat -anp | grep mysql tcp 0 0 [server ip]:3306 0.0.0.0:* LISTEN 6349/mysqld unix 2 [ ACC ] STREAM LISTENING 12286 6349/mysqld /DATA/mysql/mysql.sock # netstat -anp | grep 3306 tcp 0 0 [server ip]:3306 0.0.0.0:* LISTEN 6349/mysqld unix 3 [ ] STREAM CONNECTED 3306 1411/audispd # lsof -i TCP:3306 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME mysqld 6349 mysql 10u IPv4 12285 0t0 TCP [domain]:mysql (LISTEN) I am running... OS CentOS release 5.8 (Final) mysql 5.5.28 (Remi) Note: Internal connections to mysql work fine. I have disabled IPtables, the box has no other firewall, it runs Apache on port 80 and ssh no problem. Had followed this tutorial - http://www.cyberciti.biz/tips/how-do-i-enable-remote-access-to-mysql-database-server.html I have bound the IP address in my.cnf user=mysql bind-address = [sever ip] port=3306 I even started over by deleting the mysql folder in my datastore and running mysql_install_db --datadir=/DATA/mysql --force Then recreated all the users as per the manual... http://dev.mysql.com/doc/refman/5.5/en/adding-users.html I have created one test user CREATE USER 'test'@'%' IDENTIFIED BY '[password]'; GRANT ALL PRIVILEGES ON *.* TO 'test'@'%' WITH GRANT OPTION; FLUSH PRIVILEGES; So all I can see is that the port is not really open. Where else might I look? thanks

  Read the article

• How to tunnel a local port onto a remote server

  - by Trevor Rudolph

  I have a domain that i bought from DynDNS. I pointed the domain at my ip adress so i can run servers. The problem I have is that I don't live near the server computer... Can I use an ssh tunnel? As I understand it, this will let me access to my servers. I want the remote computer to direct traffic from port 8080 over the ssh tunnel to the ssh client, being my laptop's port 80. Is this possible? EDIT: verbose output of tunnel macbookpro:~ trevor$ ssh -R *:8080:localhost:80 -N [email protected] -v OpenSSH_5.2p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /Users/trevor/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: Connecting to site.com [remote ip address] port 22. debug1: Connection established. debug1: identity file /Users/trevor/.ssh/identity type -1 debug1: identity file /Users/trevor/.ssh/id_rsa type -1 debug1: identity file /Users/trevor/.ssh/id_dsa type 2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'site.com' is known and matches the RSA host key. debug1: Found key in /Users/trevor/.ssh/known_hosts:9 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /Users/trevor/.ssh/identity debug1: Trying private key: /Users/trevor/.ssh/id_rsa debug1: Offering public key: /Users/trevor/.ssh/id_dsa debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password [email protected]'s password: debug1: Authentication succeeded (password). debug1: Remote connections from *:8080 forwarded to local address localhost:80 debug1: Requesting [email protected] debug1: Entering interactive session. debug1: remote forward success for: listen 8080, connect localhost:80 debug1: All remote forwarding requests processed

  Read the article

• Using dnsmasq for accessing multiple nameservers assigned by DHCP

  - by Ash

  At my work desktop running openSUSE 11.4, I have a local network which gets its address, domain (work.site) and nameservers (10.100.1.1, 10.100.1.2) info through DHCP - which get written into /etc/resolv.conf I get to access the internet using the work network, and these 2 nameservers end up returning the entries for any public domain name lookups on the internet. I also have a private VPN that I end up connecting. The nameserver (10.111.1.1) and domain (private.site) are rarely bound to change for this network, but currently they're pushed by the openVPN client into networkmanager, and which also gets merged with the existing /etc/resolv.conf My resolv.conf ultimately ends up looking like this: search private.site work.site nameserver 127.0.0.1 nameserver 10.111.1.1 nameserver 10.100.1.1 As you can see the 2nd nameserver from my work network was pushed out because of the max 3 entry limitations. It is fine still, but would be a problem if that nameserver goes down for maintenance or something. So I found out that dnsmasq could help me here, and hence I setup dnsmasq just as a local DNS resolver without any DHCP support. So right now this is my /etc/dnsmasq.conf: resolv-file=/etc/resolv.conf server=/private.site/10.111.1.1 server=/1.111.10.in-addr.arpa/10.111.1.1 listen-address=127.0.0.1 bind-interfaces log-queries I've made dnsmasq get the list of nameservers from /etc/resolv.conf since NetworkManager seems to be updating this list correctly (for a max of 3 nameservers). I'm able to resolve the host names in both the networks correctly. So these are the questions I have: Is there a way I can make either NetworkManager or dhclient write out the list of nameservers somewhere else which I can make dnsmasq use as resolv-file ? How do I make dnsmasq use certain nameservers as the default for all queries ? Right now I notice that lookups for public domains on the internet are usually sent to both the nameservers - the one on work.site as well as private.site. It would be good if I can limit this only to work.site.

  Read the article

• Windows Server 2008 DHCP with RRAS

  - by Guillermo Prandi

  I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

  Read the article

• Does any Certificate Authority support both SAN and wildcards?

  - by nicholas a. evans

  My basic quandry is that wildcard certificates don't support subdomains of subdomains, nor do they help with alternate domain names. Basically, if my CN is example.com, I want a Subject Alternative Name field that looks roughly like so: DNS:example.com DNS*.example.com DNS:*.beta.example.com DNS:example.net DNS:*.example.net DNS:*.beta.example.net Using a self-signed cert, I verified that the browsers will work just fine with this. Unfortunately, none of the Certificate Authorities that I looked into (Thawte, GoDaddy, Verisign, Digicert) seemed to support both wildcard certs and Subject Alternative Name (sometimes referred to as "Multiple Domain UCC"). I even called up GoDaddy tech support to confirm. Is there a CA (trusted by 99% of browsers) that supports wildcards for the Subject Alternative Name? One little restriction: I'm saddled with Amazon EC2's single Elastic IP per instance limitation. Here are what I see as my backup plans: set up three extra EC2 instances, each configured for a different IP address and cert, and nginx reverse proxy from three of them into the app server(s) introduces latency(?), and even the cheapest EC2 instance isn't that cheap instead of dedicated reverse proxy instances, setup the four or more almost identical EC2 app servers, with nginx using the port to determine which cert to deliver, and use haproxy to distribute the traffic amongst themselves. complicated to configure and manage? I'm not using the cheapest EC2 instance type for my app servers. If I don't need 4+ app servers for the load, it raises the cost. set up an external server (outside of EC2) that doesn't have EC2's Elastic IP address restrictions, setup all of the alternate IP addresses and certificates on that server, and nginx reverse proxy from that server into the EC2 app servers. extra IP addresses are almost free (still need to pay for the server of course), but don't come with the robust "elasticity" that Amazon's Elastic IPs provide. even more latency than in the first scenario. Are these approaches crazy or reasonable? Do you have another one to suggest?

  Read the article

• IPMI not fucntioning with Network Bonding

  - by muhammed sameer

  Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

  Read the article

• Wildcard DNS, VirtualHosts on apache2, 404 for unused subdomains

  - by niel

  On an Apache2 server linked to by a DNS that includes a wildcard entry, e.g. *.example.com, subdomains that are not defined as ServerNames in any VirtualHosts point to the first defined VirtualHost, in my example this is 000-default. My Question:How would one get unused subdomains (subdomains not used in any virtualhosts) to return a 404 error to the requesting client? This must preferably show in server logs as a 404 as well. I have looked into the following possibilities: Redirecting any invalid subdomain to the home page or some other page.The problem with this method is, when someone links to your site as this.company.sucks.example.com, the client will see your home page or in my case 000-default if I do not redirect. Thanks, to Mike for pointing this out. (regex for "suck", etc definately not an option) Let the default VirtualHost point to a non-existent directory.Apache does not like this one bit, warning with every reload. Beyond the warning, everything seems fine. This seems like a hack. Does this seem like a problem (however small) to anyone? Point the default VirtualHost to a folder where the index.php is forbidden, thus creating a 403 status code.This is confusing and makes things like the following overly complicated: Say, for example, you use a subdomain per user (a big reason to use wildcard DNS, apparently), and users have the ability to view each others profiles at username.example.com. This solution is confusing to the user and completely not what I want to do. My ideal sollution will let the user know there is nothing to view at the url he entered. Preferably with a 404 and an error log entry for the address entered (not some other address). Any help would be greatly appreciated!

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0?

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). xxxx:xxxx:xxxx/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else?

  Read the article

• Changing subnet-mask of class-c network host to 255.255.0.0

  - by Prashant Mandhare

  We have a existing class-c network with IP address range 11.22.33.44/24 (just for example). My domain controller has been configured within this subnet. So all servers within this subnet have subnet mask configured to 255.255.255.0. Now we have got a new subnet with IP address 11.22.88.99/24 (note that only last 2 octets have changed). I want all new hosts in this new subnet to join my existing DC. For this we have configured firewall properly so allow this. (so there is no issue with firewall). But initially I was not able to join hosts in new subnet in existing domain. Later I doubted on subnet mask used in domain controller (255.255.255.0) and for testing purpose I changed it to 255.255.0.0, it worked like charm, i was able to join subnet-2 hosts in subnet-1 domain. Now i am wondering whether it will be good practice to change subnet mask of a class-c network to 255.255.0.0? Can any issues arise due to this? Experts please provide your opinion.

  Read the article

• How do I access the web server on my desktop from my laptop?

  - by Steven

  I'm running Apache on my stationary and I would like to access a website through my laptop. This is some of the Apache config: NameVirtualHost 127.0.0.1:80 <VirtualHost 127.0.0.1:80> ServerName mysite.com DocumentRoot I:/wamp/www/mysite/ </VirtualHost> ServerName localhost:80 <Directory /> Options FollowSymLinks AllowOverride all Order deny,allow Deny from all </Directory> On my laptop I've added the following to the HOSTS file: 10.0.0.3 mysite.com But accessing the page through mysite.com is not very successfull. If I enter the IP address directly, I only get a Forbidden message. What do I need to do in order to get this to work? Update I'm runing WAMPSERVER 2.1 (Apache 2.2.17) Apache is up and running I can ping 10.0.0.3 from laptop I'm not able to ping http://mysite.com from laptop IE gives me a 403 Forbidden - The website declined to show this webpage The only log that get's entries when trying to access the website from my laptop, is access.log. access.log 10.0.0.4 - - [13/Jun/2011:10:14:04 +0200] "GET / HTTP/1.1" 403 202 apache_error.log [Mon Jun 13 10:08:16 2011] [error] VirtualHost localhost:0 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results UPDATE 2 My apache config has the following entry: AllowOverride all Order Deny,Allow Deny from all Allow from 127.0.0.1 Could it be that this Allow from is stopping other computers accessing the page?

  Read the article

• How do I connect two computers with a LAN cable?

  - by John

  I have two machines - Windows XP and a laptop using Windows 7. I connected them with a WLAN cable. On the Windows XP machine, I set the IP address to 192.168.0.10. On the Windows 7 laptop, I set the IP address to 192.168.0.20. The laptop can see the Windows XP machine, but Windows XP machine cannot see the Windows 7 machine. But this does NOT concern me. I want to move the files from my desktop (Windows XP) to Windows 7 (laptop). That's why I'm going through all this. The problem is that when I try to connect from Windows 7 to Windows XP machine, I get this window: I don't understand what username/password is needed. I use none on the Windows XP machine. I tried all usernames - no success. Please explain in deep details how to solve my problem so I can connect to my Windows XP machine. EDIT: Maybe this can help: the Windows XP machine is named 'I' and '???????? III' is the name of the laptop. Both computers share one workgroup - WORKGROUP.

  Read the article

• Unable to access Windows share

  - by mbnoimi

  I've installed Alfresco 4.2.d under Ubuntu 12.04 LTS; Everything done fine except I can't access it from Windows share although I got the link from Alfresco explorer which is: file:///%5C%5CECSA%5CAlfresco%5CSites%5Cswsdp%5CdocumentLibrary%5CAgency%20Files%5CImages%5Ccoins.JPG I tried to access it from: \\ECSA but I failed too so I made a ping (192.168.0.70 is server IP) then I got: C:\Users\user>ping 192.168.0.70 Pinging 192.168.0.70 with 32 bytes of data: Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Ping statistics for 192.168.0.70: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\Users\user>ping ECSA Ping request could not find host ECSA. Please check the name and try C:\Users\user> Some logs of what's going on: C:\Users\user>net view ECSA System error 1707 has occurred. The network address is invalid. C:\Users\user>nbtstat -a 192.168.0.70 Local Area Connection: Node IpAddress: [192.168.0.84] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- ECSA <20> UNIQUE Registered ECSA <00> UNIQUE Registered WORKGROUP <00> GROUP Registered MAC Address = 00-00-00-00-00-00 C:\Users\user> CIFS Server Configuration in file-servers.properties ### CIFS Server Configuration - file-servers.properties ### cifs.enabled=true cifs.serverName=${localname}A cifs.domain= cifs.broadcast=255.255.255.255 cifs.bindto=192.168.0.70 cifs.ipv6.enabled=false cifs.hostannounce=true cifs.disableNIO=false cifs.disableNativeCode=false cifs.sessionTimeout=900 cifs.maximumVirtualCircuitsPerSession=16 cifs.tcpipSMB.port=445 cifs.netBIOSSMB.sessionPort=139 cifs.netBIOSSMB.namePort=137 cifs.netBIOSSMB.datagramPort=138 cifs.WINS.autoDetectEnabled=true cifs.WINS.primary=192.168.0.70 cifs.WINS.secondary=192.168.0.1 cifs.sessionDebug= cifs.pseudoFiles.enabled=true cifs.pseudoFiles.explorerURL.enabled=true cifs.pseudoFiles.explorerURL.fileName=__Alfresco.url cifs.pseudoFiles.shareURL.enabled=false cifs.pseudoFiles.shareURL.fileName=__Share.url How can I fix this issue?

  Read the article

• Why does my Belkin wireless router has eMule port open?

  - by Jeremy Powell

  I have a Belkin F6D4230-4 v1 router. When I port scan it with nmap I get the following: $ sudo nmap -sS -A -T5 192.168.2.1 -p- Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-17 11:40 CDT Interesting ports on 192.168.2.1: Not shown: 65532 closed ports PORT STATE SERVICE VERSION 80/tcp open http Belkin 2307 wifi router http config (IP_SHARER httpd 1.0) |_ html-title: '+i1+' 4661/tcp filtered unknown 4662/tcp filtered edonkey MAC Address: 00:22:75:5D:52:D8 (Belkin International) Device type: WAP|broadband router|firewall|printer|specialized|webcam Running (JUST GUESSING) : Linksys embedded (95%), TRENDnet embedded (95%), Netgear embedded (92%), Canon embedded (89%), On Time RTOS (89%), Symantec embedded (89%), D-Link embedded (86%), Polycom embedded (85%) Aggressive OS guesses: Linksys WRT54GC or TRENDnet TEW-431BRP wireless broadband router (95%), TRENDnet TW100-BRF114 broadband router (95%), Netgear FR114P ProSafe VPN firewall (92%), Canon PIXMA MX850 printer (89%), On Time RTOS (89%), Symantec Firewall/VPN 100 (89%), D-Link DI-714P+ wireless broadband router (86%), Polycom ViewStation video conferencing system (85%) No exact OS matches for host (test conditions non-ideal). Network Distance: 1 hop Service Info: Device: WAP OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 21.57 seconds Why are the 4461 and 4462 ports open? This is a basic, out-of-the-box installation.

  Read the article

• How can I close a port that appears to be orphaned by Xvfb?

  - by Jim Fiorato

  I'm running Xvfb on a FC8 Amazon EC2 image. On occasion Xvfb will crash (unable at the moment to find out the reason for the crash), and after crashing the TCP port will appear to be orphaned. I'm unable to get a PID to kill any process that may be using it. I'm starting Xvfb with: Xvfb :7 -screen 0 1024x768x24 & Examples of what I'm working with are below, the Xvfb port is (was) 6007: # netstat -ap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:ssh *:* LISTEN 1894/sshd tcp 0 0 *:6007 *:* LISTEN - tcp 0 352 ip-10-84-69-165.ec2.int:ssh c-71-194-253-238.hsd1:51689 ESTABLISHED 2981/0 udp 0 0 *:bootpc *:* 1817/dhclient udp 0 0 *:bootpc *:* 1463/dhclient Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node PID/Program name Path unix 2 [ ] DGRAM 871 668/udevd @/org/kernel/udev/udevd unix 2 [ ACC ] STREAM LISTENING 5385 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 6 [ ] DGRAM 5353 1867/rsyslogd /dev/log unix 2 [ ] DGRAM 11861 2981/0 unix 2 [ ] DGRAM 5461 1974/crond unix 2 [ ] DGRAM 5451 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5438 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 3 [ ] STREAM CONNECTED 5437 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5396 1880/dbus-daemon unix 3 [ ] STREAM CONNECTED 5395 1880/dbus-daemon unix 2 [ ] DGRAM 5361 1871/rklogd # lsof -i COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME dhclient 1463 root 3u IPv4 4704 UDP *:bootpc dhclient 1817 root 4u IPv4 5173 UDP *:bootpc sshd 1894 root 3u IPv4 5414 TCP *:ssh (LISTEN) sshd 2981 root 3u IPv4 11825 TCP ip-10-84-69-165.ec2.internal:ssh->c-71-194-253-238.hsd1.il.comcast.net:51689 (ESTABLISHED) Attempting to force the port closed with iptables doesn't seem to work either. iptables -A INPUT -p tcp --dport 6007 -j DROP I'm at a loss as to how to reclaim/free the port. From what I can tell, this port will remain in this state until the EC2 instance is shut down. So, how can I close this port so I can restart Xvfb?

  Read the article

• Issues resolving DNS entries for multi-homed servers

  - by I.T. Support

  This is difficult to explain, so bear with me. We have 2 domain controllers, each multi-homed to straddle 2 internal subnets, (subnet A and subnet B) and provide dns, dhcp, and ldap authentication. Both domain controllers each have 2 DNS entries. both entries have identical host names, but correspond to subnet A & subnet B respectively (example entries shown): dc1 host 192.168.8.1 dc1 host 192.168.9.1 dc2 host 192.168.8.2 dc2 host 192.168.9.2 We also have a 3rd subnet for our dmz, (subnet C) which neither domain controller has an IP address on, but our firewall/routing tables provide access to subnet A from subnet C and vice versa, but don't allow access to subnet B from subnet C. Here's my issue. How can I force/determine which dns entry is used when a server on subnet C queries either domain controller by host name? Right now it seems to randomly pick one of the two entries, swaps out the name for the IP address and that's that. The problem is if it randomly selects the entry that corresponds to the 9.x subnet B (no access from subnet C), then the server fails to resolve. If it picks the entry for the 8.x subnet A then it resolves (firewall/routing tables defined for communication between these 2 subnets) Here's what I'd like to know: What are Best Practices (if any) for dealing with DNS resolution on subnets that the DNS servers don't have a presence on? Can I control something akin to a metric value to force an order of DNS resolution when there are multiple entries for the same host name that correspond to different IP subnets? Should I even have 2 DNS HOST entries for the same name? Here's what I'd like to avoid: Making edits to the HOSTS files of servers on subnet C to force DNS resolution of the hostname to the appropriate subnet Adding NIC's to the DC's to have them straddle the DMZ as well, thus obtaining a third DNS entry that corresponds to subnet C Again, my apologies if this was too verbose / unclear. Thanks!

  Read the article

• Freeradius authentication failed for unknown reason

  - by Moein7tl

  I followed this instruction to force freeradius to use mysql database. and run freeradius in debug mod. but it rejects all authentication. mysql database : mysql select * from radcheck; +----+----------+-----------+----+---------+ | id | username | attribute | op | value | +----+----------+-----------+----+---------+ | 1 | test | Password | == | test123 | | 2 | test | Auth-Type | == | Local | +----+----------+-----------+----+---------+ 2 rows in set (0.02 sec) radtest command : # radtest test test123 localhost 0 testing123 Sending Access-Request of id 235 to 127.0.0.1 port 1812 User-Name = "test" User-Password = "test123" NAS-IP-Address = 127.0.0.1 NAS-Port = 0 Message-Authenticator = 0x00000000000000000000000000000000 rad_recv: Access-Reject packet from host 127.0.0.1 port 1812, id=235, length=20 radiusd debug mod log: rad_recv: Access-Request packet from host 127.0.0.1 port 51034, id=235, length=74 User-Name = "test" User-Password = "test123" NAS-IP-Address = 127.0.0.1 NAS-Port = 0 Message-Authenticator = 0xbf111cbbae24fb0f0a558bfa26f53476 # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "test", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] No EAP-Message, not doing EAP ++[eap] returns noop ++[files] returns noop ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop ERROR: No authenticate method (Auth-Type) found for the request: Rejecting the user Failed to authenticate the user. Using Post-Auth-Type Reject # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group REJECT {...} [attr_filter.access_reject] expand: %{User-Name} - test attr_filter: Matched entry DEFAULT at line 11 ++[attr_filter.access_reject] returns updated Delaying reject of request 20 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 20 Sending Access-Reject of id 235 to 127.0.0.1 port 51034 Waking up in 4.9 seconds. Cleaning up request 20 ID 235 with timestamp +4325 Ready to process requests. where is the problem and how should I solve it?

  Read the article

• Ubuntu 12.04 Server - eth0 1Gbps NIC eth1 10Gbps NIC - all traffic using eth0?

  - by James

  Ubuntu Server 12.04.1 x64 Primary role is an NFS fileserver, for Mac OSX Clients. Hardware: Eth0: 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) Eth1: 07:00.0 Ethernet controller: MYRICOM Inc. Myri-10G Dual-Protocol NIC Config: ifconfig eth0 Link encap:Ethernet HWaddr <MACADDRESS> inet addr:192.168.0.150 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:460042020 errors:0 dropped:148 overruns:0 frame:0 TX packets:231906707 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:581431978417 (581.4 GB) TX bytes:259057368617 (259.0 GB) Interrupt:20 Memory:f7d00000-f7d20000 eth1 Link encap:Ethernet HWaddr <MACADDRESS> inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6832208 errors:0 dropped:2 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:513826442 (513.8 MB) TX bytes:33688 (33.6 KB) Interrupt:59 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:507 errors:0 dropped:0 overruns:0 frame:0 TX packets:507 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:45057 (45.0 KB) TX bytes:45057 (45.0 KB) nano /etc/network/interfaces #The loopback network interface auto lo iface lo inet loopback #The primary network interface auto eth0 iface eth0 inet static address 192.168.0.150 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 #second network interface auto eth1 iface eth1 inet static address 192.168.0.100 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 Currently I am using on the OSX clients: nfs://192.168.0.100/Volumes/Storage to mount the NFS share. My problem is why would all the data (and I have checked using various monitoring tools bmon, iftop, glances, etc) be going over the slower connection?? Also, after configuring /etc/network/interfaces with the above setup I always get an error message at bootup something about waiting for network configuration. Are these connected?

  Read the article

• Unable to connect to EC2 instance after "reboot"

  - by KPL

  I am not able to connect to my m1.small instance after rebooting it. I have already associated the public IP with this instance. Upon checking the system log, this seems to be the issue: cloud-init-nonethttp://11.84: waiting 10 seconds for network device cloud-init-nonethttp://21.85: waiting 120 seconds for network device cloud-init-nonethttp://141.85: gave up waiting for a network device. Cloud-init v. 0.7.3 running 'init' at Sun, 18 May 2014 07:02:55 +0000. Up 142.54 seconds. ci-info: +++++++++++++++++++++++Net device info++++++++++++++++++++++++ ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | Device | Up | Address | Mask | Hw-Address | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | lo | True | 127.0.0.1 | 255.0.0.0 | . | ci-info: | eth0 | False | . | . | 02:43:xx:xx:xx:xx | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Route info failed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! A bunch of these follow the above message: 2014-05-18 07:02:56,178 - url_helper.pyWARNING: Calling http://169.254.169.254/2009-04-04/meta-data/instance-id failed 0/120s: request error [HTTPConnectionPool(host='169.254.169.254', port=80): Max retries exceeded with url: /2009-04-04/meta-data/instance-id (Caused by : Errno 101] Network is unreachable) This is obviously related to the network interface not being working correctly. I have tried this so far: Relaunch a new instance from the custom AMI (created from EBS) of the failing instance. The same error shows up in the logs. Attach a new network interface to the EC2 instance. The error still persists. eth1 shows up in the list but the "up" column is False.

  Read the article

• Ubuntu 12.04 on VMware Player loses network configuration

  - by d4ryl3

  I've been having this issue for 2 weeks now with my VMware Player-hosted Ubuntu 12.04. I only use it for my LAMP stack. I've had no issues with it before until about 2 weeks ago when it almost always (once per day at least) loses its network configuration. On boot it shows: Waiting for network configuration... Waiting up to 60 more seconds for network configuration... Booting system without full network configuration... Then when I do ifconfig -a it doesn't show an IP Address and couldn't get online. The only resolutions I've found so far was either to reinstall VMware Tools or use the VMware Player installer and choose Repair. This is frustrating to me because even when the issue was resolved after doing either of the steps I mentioned, the IP Address gets changed. Then I'd have to update the Remote Configuration of my IDE (Netbeans) and my database manager. What could possible cause this? Please help. Thank you. Additional details: I'm using a laptop with Windows 7 and connected to the office WiFi, which is unrestricted as far as I know. Thanks again.

  Read the article

• Bash Script - Traffic Shaping

  - by Craig-Aaron

  hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

  Read the article

• DRBD on a disk with existing file system that takes all the place

  - by Karolis T.

  I'm currently trying to simulate the environment via XEN. I have installed two debian systems with such FS layout: cltest1:/etc# df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda2 6.0G 417M 5.2G 8% / tmpfs 257M 0 257M 0% /lib/init/rw udev 10M 16K 10M 1% /dev tmpfs 257M 4.0K 257M 1% /dev/shm Host cltest2 is identical. Here's my drbd.conf global { minor-count 1; } resource mysql { protocol C; syncer { rate 10M; # 10 Megabytes } on cltest1 { device /dev/drbd0; disk /dev/xvda2; address 192.168.1.186:7789; meta-disk internal; } on cltest2 { device /dev/drbd0; disk /dev/xvda2; address 192.168.1.187:7789; meta-disk internal; } } I have not created filesystem on drbd0 Starting DRBD via init.d script errors out with: Starting DRBD resources: [ d(mysql) /dev/drbd0: Failure: (114) Lower device is already claimed. This usually means it is mounted. [mysql] cmd /sbin/drbdsetup /dev/drbd0 disk /dev/xvda2 /dev/xvda2 internal --set-defaults --create-device failed - continuing! Running: drbdadm create-md mysql gives: cltest1:/etc# drbdadm create-md mysql md_offset 6442446848 al_offset 6442414080 bm_offset 6442217472 Found ext3 filesystem which uses 6291456 kB current configuration leaves usable 6291228 kB Device size would be truncated, which would corrupt data and result in 'access beyond end of device' errors. You need to either * use external meta data (recommended) * shrink that filesystem first * zero out the device (destroy the filesystem) Operation refused. Command 'drbdmeta /dev/drbd0 v08 /dev/xvda2 internal create-md' terminated with exit code 40 drbdadm aborting As I understand, all of my problems are because I don't have unallocated disk space on xvda2. What are my options besides shrinking FS and connecting a separate physical disk? Can't the meta-data be stored on a file in the local filesystem?

  Read the article

• Active Directory Domain Services - Network Name Cannot be Found

  - by Arief

  I have really weird problem that I could not explain. I am trying to redirect all users home folder to the new server. I have copied all the files including the permissions to the new server. All I need to do is to update the user profile for home folder by changing the server name. However, I got this message when I enter the new server name: My server that serving as AD can resolve the name by ping and nslookup of the server name. The only thing that I don't understand why the MMC cannot resolve the name. I did change with the IP Address and I still get the same error message. Thank you so much for your help. UPDATE: I know what seems to be a problem, but I don't know how to fix it. The new server that will serve all Home folder is actually sitting in the cloud with different IP Address as the Domain Controller. The Domain Controller is sitting locally in the office with 10.0.0.0/24 IP Addresses. The new server that is sitting in on Data Centre is on 172.10.10.10/24 IP Addresses. The static route has been set up on both end, and the DNS as well. I believe this is the issue. Does anyone how to overcome this situation? Thank you.

  Read the article

• Deploying a Git server in a AWS linux instance

  - by Leroux

  I'm making a git server on my linux instance in AWS. I tried doing it using these instructions but in the end I always get stuck with a "Permission denied (publickey)" message. So here is my detailed steps, the client is my windows machine running mysysgit and the server is the AWS ubuntu instance : 1) I created user Git with a simple password. 2) Created the ssh directory in ~/.ssh 3) On the client I created ssh keys using ssh-keygen -t rsa -b 1024, they got dropped in my /Users/[Name]/.ssh directory, id_rsa and id_rsa.pub key pair was created. 4) Using notepad I copy pasted the text into newly created files on the server in the ~/.ssh directory of my Git user. ~/.ssh/id_rsa and **~/.ssh/id_rsa.pub** were copied. 5) On the server I made the authorized_hosts file using "cat id_rsa.pub authorized_hosts" (while inside the .ssh directory) 6) Now to test it, on my client machine I did ssh -v git@[ip.address] 7) Result : debug1: Host 'ip.address' is known and matches the RSA host key. debug1: Found key in /c/Users/[Name]/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /c/Users/[Name]/.ssh/identity debug1: Trying private key: /c/Users/[Name]/.ssh/id_rsa debug1: Offering public key: /c/Users/[Name]/.ssh/id_dsa debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). I would appreciate any insight anyone can give me.

  Read the article

< Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >