Search Results

Search found 7770 results on 311 pages for 'timothy high'.

Page 237/311 | < Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >

• Is there a better way to do bonded vlan tagged interfaces with XEN

  - by AJ01

  We have a number of XEN servers all running CentOS or RHEL. The VM's that they run are all required to be on their own VLAN for no other reason than the customer expects them to be. Long story short however, I can't change this right now. We are also required to have bonding enabled on the interfaces. So to accommodat this we enslave eth1 and eth2 to bond0. We then create a seperate interface called bond0.VLANID where VLANID corresponds to the correct vlan; eg ifcfg-bond0.204 DEVICE=bond0.204 BOOTPROTO=static ONBOOT=yes VLAN=yes BRIDGE=xenvlan204 Bridge to XEN As you will see, we eventually have to bridge this out to XEN, and we do this by adding another interface called xenvlan204 (in this instance) which contains; ifcfg-xenvlan204 DEVICE=xenvlan204 BOOTPROTO=none ONBOOT=yes TYPE=bridge XEN Vm Config Finally in our XEN config for each VM, we add vif = [ "bridge=xenvlan204" ] This then allows the vm host to access that particular vlan The Problem We've noticed a few problems with this setup. One being that we currently create the interfaces manually. Which means if we add more vlan enabled interfaces and bridges we usually have to restart xend which is something I'm not so hot about. Also lower level staff have their heads melted by the number of interfaces and the risk of a mistake occurring is high. Secondly, it can take sometime for a host to come up if it has a number of vlan taged interfaces. Thirdly, its just not scaling well on the management aspects The Question Is there a better more flexible way to do this (in particular with Xen that ships with centos 5.3, 5.4 and 5.5 as we have to support all three) that leverages either scripting or other solutions to allow an arbitrary amount of interfaces to be created when a vm is instanced. Your advise and expertise is more that welcomed.

  Read the article

• No sound out of headphone port on laptop

  - by Thanatos

  I cannot get sound out of the headphone port on a laptop. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Some edits: Yes, the headphones are in all the way. This works in Windows: You plug headphones in, the internal speakers stop making noise, and noise comes out the head phones. Windows says I only have two sound cards: the HDMI port (which I don't care about) and the "sound card", which it claims is a "Conexant Pebble High Definition SmartAudio" In Windows, both the internal speakers and the headphone jack show up as one soundcard, which in my experience, is typical. (This is a laptop)

  Read the article

• Redirection of outbound UDP port NTP.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• Windows desktop virutalization instead of replacing work stations

  - by Chris Marisic

  I'm head of the IT department at the small business I work for, however I am primarily a software architect and all of my system administration experience and knowledge is ancillary to software development. At some point this year or next we will be looking at upgrading our workstation environment to a uniform Windows 7 / Office 2010 environment as opposed to the hodge podge collection of various OEM licensed editions of software that are on each different machine. It occurred to me that it is probably possible to forgo upgrading each workstation and instead have it be a dumb terminal to access a virutalization server and have their entire virtual workstation hosted on the server. Now I know basically anything is possible but is this a feasible solution for a small business (25-50 work stations)? Assuming that this is feasible, what type of rough guidelines exist for calculating the required server resources needed for this. How exactly do solutions handle a user accessing their VM, do they log on normally to their physical workstation and then use remote desktop to access their VM, or is it usually done with a client piece of software to negotiate this? What types of software available for administering and monitoring these VM's, can this functionality be achieved out of box with Microsoft Server 2008? I'm mostly interested in these questions relating to Server 2008 with Hyper-V but fell free to offer insight with VMware's product line up, especially if there's any compelling reasons to choose them over Hyper-V in a Microsoft shop. Edit: Just to add some more information on implementation goals would be to upgrade our platform from a Win2k3 / XP environment to a full Windows 2008 / Win7 platform without having to perform any of that associated work with our each differently configured workstation. Also could anyone offer any realistic guidelines for how big of hardware is needed to support 25-50 workstations virtually? The majority the workstations do nothing except Office, Outlook and web. The only high demand workstations are the development workstations which would keep everything local.

  Read the article

• ActiveDirectory user files aren't being shared? [on hold]

  - by Ryan

  I'm taking a class in college and my current project is to setup Active Directory. So I have two VMs, one is Windows Server 2008 R2 and the other is Windows 7. I setup the domain team15.net (this is the FQDN for the forest) on the W2008 server machine. And then I connected the Windows 7 machine to the team15.net domain, and now I can login to the administrator account on the W2008 machine by using TEAM15\Administrator for the username. However, any files that I add in Windows 7 while logged into TEAM15\Administrator are NOT shown in the Windows 2008 machine. Is this normal? It seems like any files I add to this user in the domain only exists for the machine that I'm currently using. Is it possible to change this so all files for all users are synced to all computers in the domain? If not then what are alternatives? I noticed that back in high school we also used domains but there was a shared drive E:\ that you had to store your files because if you put them on in the desktop instead then they would suddenly disappear once you logged out and back in. How can I setup a shared drive? and which computer would provide the storage for this drive?

  Read the article

• Improve wireless performance

  - by djechelon

  Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

  Read the article

• Ubuntu 10.10 forgets desktop theme.

  - by Marcelo Cantos

  I am running Ubuntu in VirtualBox (on a Windows 7 host). Several times now, the top-level menu bar, the task bar — and seemingly every system dialog — have forgotten the out-of-the-box "Ambiance" theme they conform to when I first installed the system. Window captions still preserve the theme, but pretty much nothing else does. I have searched high and low on Google for assistance with this problem. Everything I've found suggests either running some gconf reset or deleting .gconf* .gnome* and other similar directories. I have followed all this advice and nothing works. I still get a boring Windows-95-style gray 3D look and feel. On previous occasions, after much messing around I've given up and rebooted the VM instance, and been pleasantly suprised to see the original "Ambience" theme restored throughout the UI, but invariably it disappears again some time later, usually after a reboot, so I can never figure out what I did that broke it. Here's a sample from Ubuntu's site of what I want it to look like. And here's a screenshot of my system as it currently looks. Also note that my GNOME Terminals normally have a nice purple semi-translucent look, and as can be seen from the screenshot, they are now just a solid matt white. This last time (just this morning), trying numerous combinations all the usual tricks and rebooting several times hasn't fixed it, so here I am on SU wondering: How do I recover the out-of-the-box theme for my Gnome/Ubuntu desktop, noting that blowing away all config files — as suggested in many places online — fails to achieve this? EDIT: It might help to know that it seems to fail either after I resize the VM instance, forcing the Ubuntu desktop to resize itself, or after I play around with Compiz settings. I haven't been able to figure out which of these it is, and it could be neither. Given the amount of pain I have had to go through to get things back to normal (and given that I am at a loss as to how to do so), it has proven difficult to definitively isolate the cause.

  Read the article

• Best way to build / implement a corporate developer Linux distro with multiple kernels?

  - by Garen

  At work we have Linux users who understandably prefer using Ubuntu. Problem is, we also have developer tools that only work with 'officially' supported Linux distributions that use much older 2.6.18 based kernels. (And even if they worked with newer ones, the vendors could always say they won't "support" the software unless it's on one of their 'officially' supported platforms.) We could of course just tell them to use CentOS or something else 2.6.18-based, and I'm sure their response would be something like: "you can take Ubuntu from our cold, dead hands." :) Which brings to me some questions--is there any good/easy/recommended way to run something like Ubuntu as a host VM and Centos 5.x as a guest OS (with which system--Xen,KVM,VMWare, ...?), and then roll that into our own custom internal distribution that could be easily installed? KVM looks like a good high-performance option just recently included in RHEL 5.4, but if hardware support for virtualization like Intel-VT or AMD-V is necessary, then I'd guess only those folks with fairly new PCs will be able to do it. Would be very interested to hear how anyone else has addressed this kind issue. EDIT: The target audience / users of this kind of system would be developers, each one needs to run locally licensed commercial software, so building out some separate beefy central machines isn't an option unfortunately due to license restrictions. Even if that weren't the case, a couple developers could quickly eat up the resources with parallel builds. :) Ideally, I was hoping there was some step-by-step guide out there to build your own pre-built distribution that had e.g. CentOS 5.x and Ubuntu Desktop as a guest.

  Read the article

• Find slow network nodes between two data centers

  - by 2called-chaos

  I've got a problem with syncing big amount of data between two data centers. Both machines have got a gigabit connection and are not fully occupied but the fastest that I am able to get is something between 6 and 10 Mbit = not acceptable! Yesterday I made some traceroute which indicates huge load on a LEVEL3 router but the problem exists for weeks now and the high response time is gone (20ms instead of 300ms). How can I trace this to find the actual slow node? Thought about a traceroute with bigger packages but will this work? In addition this problem might not be related to one of our servers as there are much higher transmission rates to other servers or clients. Actually office = server is faster than server <= server! Any idea is appreciated ;) Update We actually use rsync over ssh to copy the files. As encryption tends to have more bottlenecks I tried a HTTP request but unfortunately it is just as slow. We have a SLA with one of the data centers. They said they already tried to change the routing because they say this is related to a cheap network where the traffic gets routed through. It is true that it will route through a "cheapnet" but only the other way around. Our direction goes through LEVEL3 and the other way goes through lambdanet (which they said is not a good network). If I got it right (I'm a network intermediate) they simulated a longer path to force routing through LEVEL3 and they announce LEVEL3 in the AS path. I basically want to know if they're right or they're just trying to abdicate their responsibility. The thing is that the problem exists in both directions (while different routes), so I think it is in the responsibility of our hoster. And honestly, I don't believe that there is a DC2DC connection which only can handle 600kb/s - 1,5 MB/s for weeks! The question is how to detect WHERE this bottleneck is

  Read the article

• Disk usage on IIS, PHP5, performance problems.

  - by Jacob84

  Hi everybody, I'm quite worried with a performance problem that I'm facing in one of our production servers. I'm working for a hosting company, so you can imagine how heterogeneous the applications runnning here are. All started with a call of a client complaining about the speed loading a Joomla. The setup is IIS6 (Windows 2003) with PHP5 and FAST CGI wich normally works pretty well. I've tested the loading time and indeed, he was right. 7 or 8 seconds to load, when usually this can be accomplished in 2. Seeing this results, I started to check first CPU and RAM. Everithing normal, 2GB of RAM free, 3%-8% of CPU activity. That's what I call a relaxed server ;). Unfortunately, digging a little deeper I've found the 'PhysicalDisk' counters quite high (above 10), specially the read queues. I've used Process Explorer to see wich of those processes has the higher deltas, but everything seemed normal. As the problem is specially related to PHP pages, I've checked specific IIS counters, as Actual connections, Number of CGI requeriments and Number of ISAPI requeriments. CGI -> 3 to 7 ISAPI -> 5 to 9 Connections-> 90 to 120 (wich appears at the top of the graph) More than a solution (I know this is hard to find), I would like to know if you have an specifical methodology to face this kind of problems. Thanks a lot, as always.

  Read the article

• Why is dwm.exe using so much memory?

  - by Leonard Challis

  I've scoured the web, but I'm sick of reading "scan your computer for viruses" and "upgrade your RAM" on answers to similar questions to this. I understand that dwm.exe is for (simply put) caching bitmaps for things like Aero-peek and similar, but as far as I have read it shouldn't be using vast amounts of memory. My colleague and I both have 4GB of RAM, Core 2 Duo, blah, blah -- essentially they're pretty capable. His dwm.exe is running at around 30mb, mind is currently running at about half a gig, though it does fluctuate quite a lot. This is the same while running the exact same applications (currently Zend studio, FireFox (with firemin - low memory usage), Outlook). Every so often I will get a notification asking me if I want to switch to Aero Basic because it's using too much memory, and sometimes it will just switch itself to basic and let me know why. I know it's possible to stop it switching, but I want to know why it is using too much memory otherwise it's just papering over the cracks. One thing to add is this seems to have started after a robbery on Monday, where two of my monitors were stolen, and I had to temporarily use a couple of alternative monitors. I am now using brand new monitors but the problem is the same. All drivers installed and working seemingly fine. Any ideas why the usage is so high? We are using windows 7 64-bit Professional.

  Read the article

• Which CPU for XEN - LAMP testbed - Budget

  - by deploymonkey

  Dear serverfault knowledgeables, im in a decision dilemma right now, which I can't resolve due to lack of hands on experience. I need to build a testbed for basically virtualizing a LAMP application (os'ses not yet decided) including server side calculations. I'll opt for XEN since it seems better supported by cloud hosters at the moment. The hardware is for a proof of concept for a startup doing saas and might be used for closed live alpha/beta later on. After testing, the testbed might be a) deployed as a colocated white box server b) used as workstation Single socket is enough. We want to have ECC memory for reliability, this excludes most of the consumer line at intel. If intel CPU, then threaded cpu (HT) is preferred have at least 16 gig ram If justified by price and reliability is not too bad, a high quality desktop MB instead of a server MB would be worth a try It came down to the opteron 6128 vs. the xeon 5620 for me after a lot of research, but I don't necessarily have to be right. Which CPU is preferrable, concerning TCO (MB price, power requirements 24/7...) , Opteron 6128 or Xeon 5620? Which one offers better performance in real world applications? (Do You have any other suggestions I probably overlooked?) Thank You for Your consideration

  Read the article

• To what extent is size a factor in SSD performance?

  - by artif

  To what extent is the size of an SSD a factor in its performance? In my mind, correct me if I'm wrong, a bigger SSD should be, everything else being equal, faster than a smaller one. A bigger SSD would have more erase blocks and thus more leeway for the FTL (flash translation layer) to do garbage collection optimization. Also there would be more time before TRIM became necessary. I see on Wikipedia that it remarks that "The performance of the SSD can scale with the number of parallel NAND flash chips used in the device" so it seems throughput also increases significantly. Also many SSDs contain internal caches of some sort and presumably those caches are larger for correspondingly large SSDs. But supposing this effect exists, I would like a quantitative analysis. Does throughput increase linearly? How much is garbage collection impacted, if at all? Does latency stay the same? And so on. Would the performance of a 8 GB SSD be significantly different from, for example, an 80 GB SSD assuming both used high quality chips, controllers, etc? Are there any resources (webpages, research papers, presentations, books, etc) that discuss correlations between SSD performance (4 KB random write speed, latency, maximum sequential throughput, etc) and size? I realize this does not really sound like a programming question but it is relevant for what I'm working on (using flash for caching hard drive data) which does involve programming. If there is a better place to ask this question, eg a more hardware oriented site, what would that be? Something like the equivalent of stack overflow (or perhaps a forum) for in-depth questions on hardware interfaces, internals, etc would be appreciated.

  Read the article

• How to stop Firefox on an SSD from freezing when using the search box or submitting a form?

  - by sblair

  Firefox usually freezes for about a second whenever I search for something from the toolbar search box, when submitting a form, or when clearing the search box history. I suspect it has something to do with the auto-complete feature. Using Windows 7's Resource Monitor, the problem seems to be from the file: C:\Users\<username>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\formhistory.sqlite-journal I believe this is a temporary file which caches database writes. The following screenshot shows the very high response times from six different searches, and that the queue length on drive C shoots off the scale: My Firefox profile is on an Intel X25-M G2 SSD. The problem doesn't seem to occur if I create a new profile on a hard disk drive. However, I'd like to know why the problem exists on the SSD in the first place (because it's an annoying problem which contradicts the reason I bought an SSD, and it might happen with other applications too), and how to prevent it. It still occurs if Firefox is started in safe mode, and with the recent beta versions. Updates: VACUUMing the Firefox profile databases does not help with this problem. The SSD Optimizer in the Intel SSD Toolbox does not help either.

  Read the article

• How to diagnose storage system scaling problems?

  - by Unknown

  We are currently testing the maximum sequential read throughput of a storage system (48 disks total behind two HP P2000 arrays) connected to HP DL580 G7 running RHEL 5 with 128 GB of memory. Initial testing has been mainly done by running DD-commands like this: dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=3000 In parallel for each disk. However, we have been unable to scale the results from one array (maximum throughput of 1.3 GB/s) to two (almost the same throughput). Each array is connected to a dedicated host bust adapter, so they should not be the bottleneck. The disks are currently in JBOD configuration, so each disk can be addressed directly. I have two questions: Is running multiple DD commands in parallel really a good way to test maximum read throughput? We have noticed very high SWAPIN-% numbers in iotop, which I find hard to explain because the target is /dev/null How shoud we proceed in trying to find the reason for the scaling problem? Do you thing the server itself is the bottleneck here, or could there be some linux parameters that we have overlooked?

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• Log shipping on select tables.

  - by Scott Chamberlain

  I know I am most likely using incorrect terminology so please correct me if I use the wrong terms so I can search better. We have a very large database at a client's site and we would like to have up to date copies of some of the tables sent across the internet to our servers at our office. We would like to only copy a few of the tables because the bandwidth requirement to do log shipping of the entire database (our current solution) is too high. Also replication directly to our servers is out of the question as our servers are not accessible from the internet and management does not want to do replication (more on that later). One possible Idea we had is to do some form of replication on the tables we need to another database on the same server and do log shipping of that second smaller database but management is concerned that the clients have broken replication (it was between two servers on their internal network however) on us in the past and would like to stay away from it if possible. Any recommendations would be greatly appreciated. If using some form of replication is the only solution, I am not against replication, I just need compelling arguments to convince management to do it. This is to be set up on multiple sites that are running either Sql2005 or Sql2008 we will have both versions on our end to restore the data to so that is not a issue. Thank you.

  Read the article

• i7 Windows 7 laptop or Macbook Pro 15" (For making 3D model and Animation)

  - by sppdhs

  Hi everyone, I'm thinking of buying a new laptop as my current one will be 5 years old next year and it currently gives me a blue screen everytime I run a heavy software to make 3D models and animation. Question is: Should I buy Macbook Pro or a Windows 7 laptop? I tried to research and some say that Windows would be better, especially because you can buy a very high spec laptop with cheaper price. While some other say Macbook Pro is the better choice as it can run bootcamp with windows 7 100% performance on every software even though it's a mac. Is this true? Which one is actually better? Btw, the software that I usually use is 3Ds Max, Maya, and ZBrush. To note as well, I have never used a Mac before. I've checked around some stores and budget wise, I'll need around AU$3000+ to buy a Macbook pro, and AU$2000+ to buy a windows laptop. Quite a big difference in price range. Thanks in advance for your help.

  Read the article

• Different external ip addresses from different sites

  - by user630286

  My router is ClearOS 6(Centos 6). In my router, I have two external (internet) network connections from two ISP's. The primary connection is eth2 connected to a cable modem and the second one is ppp0 connected to a dsl modem. I have assigned eth2 as the primary connection (with a high metric value). In fact this is done through clearos's multiwan web interface. I have a test in my Nagios to monitor whether the primary connection. This connection is done based on the result of curl ifconfig.me But it seems that ifconfig.me is always giving the ip address of my secondary connection. I tested it through a browser. Yes ifconfig.me gives the secondary internet's(ppp0) ip address. But whatismyipaddress.[com|org] give my primary ip address (eth2). I checked the default route on the router through ip route list 0/0 which also shows the primary connection (eth2) as the default route. The traceroute www.google.com and traceroute ifconfig.me both seems to trace through the primary connection (eth2). As our secondary internet connection has only got a limited download, I don't want to end up having to pay a large sum at the end of the month. Has somebody got an idea why the ifconfig.me shows my secondary address? What is the best way to ensure that my router(and thus the lan) use the right internet connection.

  Read the article

• Help, my CentOS servers keep going down , No route to host after a random uptime

  - by user249071

  Hello , I have a couple of Centos linux servers, that have a very simple task, they run nginx + fastcgi for php , and some NFS mounts between them, readonly They have some RPC commands to start some downloading processes with wget, nothing fancy , from a main server, but their behavior is very unstable, they simply go down, we tried to monitor ram , processor usage, even network connections, they don't load up so much, max network connections up to... 250 max, 15% processor usage and memory , well, doesn't even fill up, 2.5GB from 8GB max , I have no ideea why can a linux server go down like that, they aren't even public servers, no domain names installed no public serving, for sites. The only thing that I've discovered was that if i didn't restart the network service every couple of hours or so... the servers were becoming very slow, starting apps very slow, but not repoting a high usage of resources...Maybe Centos doesn't free the timeout connections, or something like that...It's based on Red Hat right? I'm not a linux expert , but I'm sure that there are a few guys out there that can easily have an answer to this , or even have some leads to what i can do ... I haven't installed snort, or other things to view if we have some DOS attacks, still the scheduled script that restarts the network each hour should put the system back online, and it doesn't.... Thank you in advance

  Read the article

• Nginx terminate SSL for wordpress

  - by Mike

  I have a bit of a problem. We run a wordpress blog behind a ngnix proxy and looking to terminate the ssl on the nginx side. Our current nginx config is upstream admin_nossl { server 192.168.100.36:80; } server { listen 192.168.71.178:443; server_name host.domain.com; ssl on; ssl_certificate /etc/nginx/wild.domain.com.crt; ssl_certificate_key /etc/nginx/wild.domain.com.key; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_prefer_server_ciphers on; ssl_session_cache shared:SSL:10m; ssl_ciphers RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; location / { proxy_read_timeout 2000; proxy_next_upstream error; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_pass http://admin_nossl; break; It just does not seem to work. If I can hit https://host.domain.com but it quickly switches back to non-secured from what I can see. Any pointers?

  Read the article

• ACER ASPIRE V3-571G-9435 Fan not kicking in leading to overclocking

  - by brythespy

  This laptop has always had this problem. The temperatures kick up to the thermal ceiling of 99C for the CPU (i7-3610QM) and 94C for the GPU (GT 640M). Problem is, the FAN doesn't give a damn. It's actually QUIETER when the temperatures are that high, than when it's at 60C or so. I figured it was a problem with the BIOS, so I updated that, no change. So maybe it was a problem with windows? Nope, same result on gaming with Ubuntu. The major problem of this, is that after gaming for ten minutes the CPU throttles itself to 1197MHz(as opposed to 3193), and the GPU goes down to 135MHz( as opposed to 843MHz). The problem is that the fan won't kick in like I know it can, because when the laptop is in POST, like at BIOS setup, the fan is like a vacuum cleaner it's so loud! I don't really care about noise, so I'd love to have the fan like that all the time as long as the temperatures don't fly through the roof... So, things I've tried so far, to avoid possible duplicate answers. Checked for dust: It's been this way since the laptop was new, and I've since then taken it apart. No dust buildup. Background stuff running?: No, problem persists across OS'es, and it happens while gaming anyways Manually underclocking both CPU/GPU: Using windows, I can force the CPU to stay at 1.1GHz, but the temperature STILL easily hits 99C after 5 min of gaming Contacted Acer support?: No help at all. They told me to update and reset the BIOS, which I have done multiple times. There are only about 6 changeable things anyway, none of which should affect the FAN control Third party fan control program?: None detect the fan So, I'm screwed until I can afford to replace this laptop, but I am very satisfied with performance in games... Whenever the CPU/GPU aren't being throttled. Anyone that can offer advice to solve this problem would be greatly appreciated. Hell, if you solved my problem I'd send you some monies through paypal.

  Read the article

• What is the best private cloud storage setup

  - by vdrmrt

  I need to create a private cloud and I'm searching for the best setup. These are my 2 most important requirements 1. Disk and system redundant 2. Price / GB as low as possible The system is going to be used as backup setup which will receive data 24/7 over SFTP and rsync. High throughput is not that important. I'm planning to use glusterfs and consumer grade 4TB hard-drives. I have worked out 3 possible setups 3 servers with 11 4TB HDD Setup up a replica 3 glusterfs and setup each hard drive as a separate ext4 brick. Total capacity: 44TB HDD / TB ratio of 0.75 (33HDD / 44TB) 2 servers with 11 4TB HDD The 11 hard-drives are combined in a RAIDZ3 ZFS storage pool. With a replica 2 gluster setup. Total capacity: 32TB (+ zfs compression) HDD / TB ratio of 0.68 (22HDD / 32TB) 3 servers with 11 4TB consumer hard-drives Setup up a replica 3 glusterfs and setup each hard-drive as a separate zfs storage pool and export each pool as a brick. Total capacity: 32TB (+ zfs compression) HDD / TB ratio of 0.68 (22HDD / 32TB) (Cheapest) My remarks and concerns: If a hard drive fails which setup will recover the quickest? In my opinion setup 1 and 3 because there only the contents of 1 hard-drive needs to be copied over the network. Instead of setup 2 were the hard-drive needs te be reconstructed by reading the parity of all the other harddrives in the system. Will a zfs pool on 1 harddrive give me extra protection against for example bit rot? With setup 1 and 3 I can loose 2 systems and still be up and running with setup 2 I can only loose 1 system. When I use ZFS I can enable compression which will give me some extra storage.

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

< Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >