Search Results

Search found 7770 results on 311 pages for 'timothy high'.

Page 238/311 | < Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• Nvidia GTX 660m crashes games

  - by dcap

  I just recently bought a Lenovo y580 with both HD intel graphics and an Nvidia GTX 660m. It works great except for one thing: playing games. Every time I load a game, either with Steam or Games for Windows Live, games will end up crashing. I've already talked with lenovo tech support and they couldn't help other than send my new laptop for repair which would take 7 days. So before I do that I thought I'd ask around. These are the games I've tested and what happens when they load: Civilization V: Game loads fine but once it gets loaded to the game, there's noticeable "tearing" popping up and certain things flash. Within a minute of this, the game crashes. Does the same thing regardless if Vsync is on or off. Total War Shogun2: Game gets to the menu screen. The background of the menu screen shows what is expected - slideshow of in-game environments rendered on high settings (this is expected). However, within 2 seconds of the menu loading up it crashes. Age of Empires 3 (Non-steam): This game is several years old so it should work on this brand new laptop fine. However the results are similar to that of Civilization V. Noticeable "Tearing" and after a few seconds it'll freeze/crash. I've done tests on all these games with both the latest stable Nvidia driver 285 as well as the nightly build 307. In addition, Nvidia control panel is set on using the dedicated graphics card for all programs. So is there anything I can do to fix this or will I have to send it back for a week to tech support?

  Read the article

• Capabilities of business and SOHO routers

  - by Q8Y

  I'm currently studying for the CCNA certifications (especially for Cisco routers and configuration). I know that business routers provide more features than SOHO routers, the processing speed and RAM can be enough. Assume I need to connect a number of users through a network (accessing internet, share files, printers, ...). I have a high speed connection to the internet and I already applied QoS. How can I find out how many users such a single (SOHO) router could handle? In my case I'd attach to it multiple switches until I have the number of ports needed. Would everything work well and smoothly with 50 users? What about 300? At which point would I need a business router instead? If I implemented VLAN here, would it make any difference in the performance? When do I really need to use more than one router? (Both SOHO and business) I'm thinking that I may need them only if I want to increase the performance (instead of replacing the existing one) and if I have multiple locations, so in this situation I need to have multiple routers, right? Put differently: Is there is a need to have another router if my business all in one place?

  Read the article

• How to manage unprivileged administration of system services using Debian?

  - by ypnos

  At our lab, we have several services handled by different phd students (like myself). Fluctuation is high and people do the job next to their research duties. Until now, services were running on different machines, with different OS setups that can result in administration hell quickly. We want to consolidate our service setup. Our main idea is that the guys responsible for the services should not meddle with the underlying system anymore. Apart from core systems like NFS and kerberos, a typical service is able to run as non-root already. I'm talking about apache, mysql, subversion, mail with openxchange, and so on. Redirecting privileged ports is also no issue (source). What is left is the configuration of the service and its payload. One scenario we envisioned is that every service has its own user and home directory, accessable by the corresponding admins. Backup and fallback of the service is easy, as everything needed for the service to run is found in one place. Are there established ways to create such a setup? Does a mostly unique method exist to make services find their files (other than in system directories) while still using the corresponding debian packages? Are there any catches with our idea that we may have overlooked? Would you maybe claim that virtualization is the answer to our problem? (In our POV, it wouldn't help us keeping system setup strictly separated from service setup.) Thank you for any advice!

  Read the article

• h264 inside FLV container vs. MP4 container?

  - by Gotys

  I am developing a tube site, and currently having issues with h264 format . By looking at youtube, I noticed they are putting their hi-def videos into mp4 container, so logically I did the same. Next, I installed mod_h264_streaming for lighttpd to make streaming and timeline-scrubbing work. Problem is, that large files (500mb+ at somewhat high resolution) take for EVER to even start buffering ( I read the flowplayer or other flash players need to download metadata first) . I moved the xmov atom to the front of the file with MP4Box (i tried qt-quickstart too) , and the problem didn't go away. Next I read online I need to interleave audio tracks, so I did that too. No change in slowness. So I tried putting the same exact h264 movie into an FLV container, and the playback buffering starts almost instantly - no slowness. So what am I missing here? Why would I choose MP4 container with mod_264_streaming module , which seems super-slow over a regular FLV container with lighttpd's built-in mod_flv_streaming ? Obviously many websites pick mp4 container , but I fail to understand why ? And as a side question - I tried using HTML5's VIDEO tag to try the same h264 MP4 movie, and the scrubbing is LIGHTING FAST! I looked into lighttpd's log file, and i noticed taht Flash Players append video.mp4?start=234 each time timeline is scrubbed, wheres HTML5's video tag does no such thing . Is this some sort of limitations of Flash ? Why Can't flash streaming be same fast as HTML5 streaming? Thanks to ALL who can help. I very much appreciate this community.

  Read the article

• What does opening a serial port do?

  - by reve_etrange

  What does opening the standard PC serial port do, in electrical terms (i.e. what voltages on which pins)? For example, the ancient VB6 program which controls an apparatus I am tasked with maintaining toggles .PortOpen to control some TTL. The connection only used 2 pins (bad solders fell apart), so which pins do I solder to? The only labels / documentation refer to pins 7 and 9, saying 0V and 5V parenthetically, but does .PortOpen really just put 5V between RI and RTS?. As a post script, this isn't the weirdest thing about the set up. The TTL I referred to above also connects to an instrument via a BNC to DB9 (!), with only 1 pin used. I guess there was an assumption about a common ground, since the BNC shielding isn't connected to the GND pin? The connection is to the instrument's 'foot pedal' pin, it was a way to remotely trigger the device. Update According to this page, the DTR and RTS pins can go high when the port is opened. If they were so configured, they will subsequently go low when the port is closed. If DTR and RTS are not enabled, opening the port should set both to low (and keep them low).

  Read the article

• which is best smart automatic file replication solution for cloud storage based systems.

  - by TORr0t

  I am looking for a solution for a project i am working on. We are developing a websystem where people can upload their files and other people can download it. (similar to rapidshare.com model) Problem is, some files can be demanded much more than other files. The scenerio is like: I have uploaded my birthday video and shared it with all of my friend, I have uploaded it to myproject.com and it was stored in one of the cluster which has 100mbit connection. Problem is, once all of my friends want to download the file, they cant download it since the bottleneck here is 100mbit which is 15MB per second, but i got 1000 friends and they can only download 15KB per second. I am not taking into account that the hdd is serving same files. My network infrastrucre is as follows: 1 gbit server(client) and connected to 4 Nodes of storage servers that have 100mbit connection. 1gbit server can handle the 1000 users traffic if one of storage node can stream more than 15MB per second to my 1gbit (client) server and visitor will stream directly from client server instead of storage nodes. I can do it by replicating the file into 2 nodes. But i dont want to replicate all files uploadded to my network since it is costing much more. So i need a cloud based system, which will push the files into replicated nodes automatically when demanded to those files are high, and when the demand is low, they will delete from other nodes and it will stay in only 1 node. I have looked to gluster and asked in their irc channel that, gluster cant do such a thing. It is only able to replicate all the files or none of the files. But i need it the cluster software to do it automatically. Any solutions ? (instead of recommending me amazon s3) S

  Read the article

• Video card not detected in POST on initial boot.

  - by Jeff M

  I have a minor problem with my desktop computer after cleaning it out for dust. When I first boot up the computer, the video card does not get detected so I can't see anything. In POST, I'm getting the "can't detect video card" beeps. The boot sequence continues normally, just without video. However, if I restart it (using the restart button) anytime after POST, it would boot up normally. I have no reason to think that the motherboard, video card or PSU got damaged in the process. It was working fine before, works fine after resetting. Took all the necessary precautions while cleaning. On the initial boot, I can hear the video card's fan power up but immediately power down and try again one more time only to fail. After the beep, resetting gets everything running and sounding normally. I've reseated the card a couple of times and reset the BIOS but doesn't seem to help. I'm hoping I won't have to take it out and remove and reinstall everything again. Does anyone recognize these symptoms to know exactly what the problem is? My guess is that the video card isn't getting enough juice initially to be running stable to be detected. I just don't know what I did (or didn't do) to get it to be in this state. It's not a high priority thing for me at the moment, just means I have to always reset it after initially turning it on but will eventually remove everything and reinstall if it comes to that. I don't think the specs are relevant here but just in case, here's the relevant stuff: Motherboard: Gigabyte P35-DS3P Video: EVGA GeForce 8600 GTS PSU: Antec True Power Trio 650W Built ~2 years ago, still running well

  Read the article

• Hearing a clicking noise from soundcard all the time

  - by Mehrdad

  I have installed Fedora 17 on my laptop. A few days ago I updated my fedora (but not upgraded). I shut down my computer and since the next time I turned it on I am hearing a clicking noise all the time from speakers. Even when I plug my headphones in I hear the noise through the headphone. I surfed over the internet and found the following shell commands: su -c 'echo "options snd_hda_intel power_save=0" /etc/modprobe.d/snd_hda_intel.conf' su -c 'echo 0 /sys/module/snd_hda_intel/parameters/power_save' I tried them but they didn't work. Here is the part of "lspci" command related to my sound-card: 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) I have to add that my sound-card is working and I can play some audio file, I mean I can hear the voice and noise simultaneously. But everything is OK in windows xp which is also installed on my laptop. Could it be related to the sound-card driver? If so, how can I revert it to the previous version?

  Read the article

• Hide/Replace Nginx Location Header?

  - by Steven Ou

  I am trying to pass a PCI compliance test, and I'm getting a single "high risk vulnerability". The problem is described as: Information on the machine which a web server is located is sometimes included in the header of a web page. Under certain circumstances that information may include local information from behind a firewall or proxy server such as the local IP address. It looks like Nginx is responding with: Service: https Received: HTTP/1.1 302 Found Cache-Control: no-cache Content-Type: text/html; charset=utf-8 Location: http://ip-10-194-73-254/ Server: nginx/1.0.4 + Phusion Passenger 3.0.7 (mod_rails/mod_rack) Status: 302 X-Powered-By: Phusion Passenger (mod_rails/mod_rack) 3.0.7 X-Runtime: 0 Content-Length: 90 Connection: Close <html><body>You are being <a href="http://ip-10-194-73-254/">redirect ed</a>.</body></html> I'm no expert, so please correct me if I'm wrong: but from what I gathered, I think the problem is that the Location header is returning http://ip-10-194-73-254/, which is a private address, when it should be returning our domain name (which is ravn.com). So, I'm guessing I need to either hide or replace the Location header somehow? I'm a programmer and not a server admin so I have no idea what to do... Any help would be greatly appreciated! Also, might I add that we're running more than 1 server, so the configuration would need to be transferable to any server with any private address.

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• How to prevent eMule from jamming up the router?

  - by the searcher

  Usually, when eMule is started, after some time, I find that the router is jammed, so the internet connection on that computer stopped working, or it seemed to be waiting for some port to be freed up before it can connect to a website. This sometimes affect even other PCs or Macs using the same router. Is there a way to prevent eMule from hogging too much resource or ports? I see that there is under Options -> Connection "Max Sources/File" and a "Connection Limits - Maximum Connections". Right now I set them to really low numbers: the first to 120 and the second to 200, but what are good numbers to fill in there so that it can work well without jamming up the router or use up the network resource of the PC or Mac? Or could it be that the number of files that are "Waiting" is too high, and used up too much resource? (If so, can emule automatically limit the number to 10 or 20 to prevent using too much resource?) (This happened before on Linksys router, Netgear router, and the AT&T U-verse router.)

  Read the article

• Apache using 100% CPU, once again

  - by CBenni

  Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

  Read the article

• How to verify TRIM/discard on encrypted swap?

  - by svarni

  I am using an encrypted swap partition via ecryptfs-setup-swap on my Ubuntu 13.04 computer using a SSD. I have manually set up trim for my ext4 root partition (simply by adding the "discard" option in /etc/fstab). I also manually ran fstrim on the root partition prior to booting and using dstat I saw that for a few seconds several GB/s of data have been written to the disk. That was presumably the effect of the trim command. These high writerates are reproducable by deleting huge files and have not occured before setting up trim, so I take them as evidence for working trim/discard. Manually enabling trim on my root partition has stopped the wearout of my precious new disk from 365 used reserved blocks (out of 6176 total) within three months down to 0 additional used reserved blocks within three additional months (data from SMART attributes). Because I want to minimize the wearout of my SSD I now would like to know whether my swap partition (which is encrypted using ecryptfs-setup-swap) also makes use of the trim/discard option. I tried sudo swapon -d -v /dev/mapper/cryptswap1 but did not receive particular information ("-v") about whether trim/discard ("-d") was applied. If unsupported, i would expect a message. Then I tried sudo dd if=/dev/sda6 count=1 BS=1M | xxd | less directly after booting and when no swapspace was used but I saw not only zeroes. I assume, when looking at freshly trimmed regions, the disk would send zeroes instead of reading random sectors (and according to some forums, (unencrypted) swap space is trimmed once upon boot). Long story short: Are there any ideas on how to test if trim is effectively used for my encrypted swap? And if not, any ideas on how to - at least manually, for once - trim the whole swap space? I wouldn't want to tinker with the partition itself, because I dont know if it needs to be reinitialized as (encrypted) swap - I dont want to be left with an unbootable system :)

  Read the article

• Short, intermittent USB port timeouts

  - by jacobsee

  I have a data acquisition application controlled by a Windows PC. I am using an Intel Desktop Board DH67CL motherboard. This has 6 USB2 ports along with 2 of the new blue USB3 ports. The DAQ instrument connects via USB to the computer. Roughly once every day or two there is a short communication glitch with the USB that causes the instrument to disconnect briefly and then reconnect. This is logged so I know whenever it happens. Occasionally it will cause the data acquisition to stop. I've verified that the glitches will go away if I use the USB3 ports, or if I use a PCI add-on card with USB ports. So it seems that there is something going on with these built-in USB2 ports on this motherboard. I haven't yet had a chance to test with other motherboards. My question: what could be causing these glitches and how to get rid of them for this board, or is there a better motherboard to use? We have standardized on the DH67CL because it's inexpensive, has 3 PCI slots that we need, and is readily available. We don't need the power of higher-end server boards but reliability is important. Thanks. Update: This problem has been reproduced many times on different hardware, though we always use the same model of motherboard (DH67CL) and power supply (Antec EA-430D). I don't think the power requirements are very high but will check on that.

  Read the article

• Postfix : outgoing mail in TLS for a specific domain

  - by vercetty92

  I am trying to configure postfix to send mail in TLS (starttls in fact), but only for a specific destination. I tried with "smtp_tls_policy_maps". This is the only line in my main.cf file regarding TLS configuration, but it seems not working. Here is my main.cf file: queue_directory = /opt/csw/var/spool/postfix command_directory = /opt/csw/sbin daemon_directory = /opt/csw/libexec/postfix html_directory = /opt/csw/share/doc/postfix/html manpage_directory = /opt/csw/share/man sample_directory = /opt/csw/share/doc/postfix/samples readme_directory = /opt/csw/share/doc/postfix/README_FILES mail_spool_directory = /var/spool/mail sendmail_path = /opt/csw/sbin/sendmail newaliases_path = /opt/csw/bin/newaliases mailq_path = /opt/csw/bin/mailq mail_owner = postfix setgid_group = postdrop mydomain = ullink.net myorigin = $myhostname mydestination = $myhostname, localhost.$mydomain, localhost masquerade_domains = vercetty92.net alias_maps = dbm:/etc/opt/csw/postfix/aliases alias_database = dbm:/etc/opt/csw/postfix/aliases transport_maps = dbm:/etc/opt/csw/postfix/transport smtp_tls_policy_maps = dbm:/etc/opt/csw/postfix/tls_policy inet_interfaces = all unknown_local_recipient_reject_code = 550 relayhost = smtpd_banner = $myhostname ESMTP $mail_name debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin xxgdb $daemon_directory/$process_name $process_id & sleep 5 And here is my "tls_policy" file: gmail.com encrypt protocols=SSLv3:TLSv1 ciphers=high I also tried gmail.com encrypt My wish is to use TLS only for the gmail domain. With this configuration, I don't see any TLS line in the source of the mail. But if I tell postfix to use TLS if possible for all destination with this line, it works: smtp_tls_security_level = may Beause I can see this line in the source of my mail: (version=TLSv1/SSLv3 cipher=OTHER); But I don't want to try to use TLS for the others domains...only for gmail... Do I miss something in my conf? (I also try whith "hash:/etc/opt/csw/postfix/tls_policy", and it's the same) Thanks a lot in advance

  Read the article

• Google Chrome is running my system out of memory

  - by jasondavis

  I am running Windows 7 x64 with 12GB of RAM I often have multiple windows and a ton of tabs open. I use the extension Session Buddy to restore all my windows and tabs once the memory gets too high. So my 12gb of ram will get up to around 93% used because of Chrome, now I can close chrome down and restore the same amount of windows and tabs and it will only use about 25% of memory, it then over time increases back up to the 90% zone after several hours. It seems that when I close tabs, instead of freeing that memory up, it doesn't so that is why the huge increase of memory usage as new tabs are opened and closed it just adds up, this sounds like a huge bug in chrome. Just for an example I just re-booted my system, I only have 1 window with 4 tabs open and in the task manager, it shows 29 chrome.exe processes I then killed all chrome processes and opened a chrome window with just 1 tab, it made 27 chrome.exe processes. Is this an issue that others have? More importantly, is there a fix? UPDATE I just read that each plugin and extension creates a chrome.exe process, I then couunted 24 extensions so that helps explain a portion of the large processes. Still not sure about memory not being freed up though!

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• Docking Station Sound Doesn't Work on Dell D830 with Windows 7

  - by cisellis

  EDIT: I can only mark one answer as the correct one but the actual solution was a combination of two comments (updating the BIOS to A15 AND installing the Sigmatel audio drivers). I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

  Read the article

• Raspberry pi slows down my entire network

  - by gnusouth

  Whenever my Raspberry Pi is connected to the network (via ethernet) the entire network is slowed to a crawl. On my main computer, ping times for google.com go from ~10ms to ~200ms and it takes forever to load web pages. Connections are also slow on the Pi, with an apt-get update showing pathetic speeds in the order of 1KB/s. Turning off the Pi completely removes the drag from the network. I've tried static and dynamic IP addresses for the Pi, but both have the same problems. I'm currently using Raspbian (downloaded today), but also had this problem with Arch Linux. I've checked the connection's duplex with dmesg | grep -i duplex, which shows that the Pi's connection is running at 100Mbps, full-duplex, as expected. My modem/router is a Billion 7404VNPX (an Australian thing); relatively high-end, albeit a bit buggy at times (it will occassionally delete all its firewall settings). It assigns IPs in the range 192.168.1.1 to 192.168.1.20 and has 192.168.1.254 as its own IP. When I assign static IPs I tend to use the 192.168.1.200 area. Does anyone have any idea as to what could be causing this weird slowdown? Or any tests I could try? Thanks

  Read the article

• Network switches for LAN party

  - by guywhoneedsahand

  I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

  Read the article

• Recommended Smartphone for Reading PDFs [closed]

  - by mika

  This is as much a software than a hardware question. I use a lot of public transport and perhaps the best way to spend your time there is to read while listening to music. Currently I use Nokia E90 and Adobe Reader LE 2.5 (full version). I was wondering if there are any better alternatives? Requirements: at least 640px wide screen, preferably 800px physical size of the LCD display matters, it should be large, but the phone itself should be as small as possible. This favors touchscreen models PDF reader should be of high quality. It should render most PDFs correctly. Other important features include: full screen mode, keyboard controls for Page Down and page change, multiple zoom levels to adjust to the screen, opening recent documents at the last page read Downsides of E90 + Adobe Reader LE Phone is large compared to the display It is hard to read the display at sunlight Adobe Reader crashes the phone regularly, zoom could have more levels, doesn't remember last page EDIT: Switched to iPhone and GoodReader. Smaller physical screen width compared to E90 is a disimprovement, but other than that I'm happy. GoodReader is the highest quality smartphone PDF reader I've seen so far.

  Read the article

• CPU operating temperature ranges

  - by osij2is

  I have an AMD Phenom II 960T with 2 cores unlocked for a total of 6 cores. I don't overclock at all. I have a Arctic Cooling ACALP64 Heatsink/Fan installed. I'm currently running ESXi 5.0 so I have to go into the BIOS to read the CPU temperatures, which at idle seem to be in the 71-74C range. To me, this is pretty high, but I cannot find any official temperature ranges that AMD says the CPU can work well within. There seems to be a lot of questions on superuser and numerous forums around CPU temperatures but no one seems to have a clear consensus as to what the manufacturer temperature ranges are for specific CPUs. I've tried searching through AMDs site to no avail. At this point, I'd be willing to shut off the 2 extra cores if it keeps the heat down but until I get some sort of tolerance or range for temperature, I have no idea if the CPU is being damaged or not. Can anyone point to a direct source, article, FAQ from AMD that specifically states their CPUs temperature range? Or are CPU temperature ranges so varying that there's no possible baseline? Am I being too paranoid about this? To me, anything over 65C is a bit much and if I'm in the low-mid 70s range with NO VMs running, what can I expect if I have several VMs running?

  Read the article

• How do I permanently delete /var/log/lastlog?

  - by GregB

  My /var/log/lastlog file is huge. I know it's really only a few kilobytes, but tar isn't smart enough to know that, so when I image a virtual machine, my restore fails because it thinks I'm trying to load more data than I have capacity on my disk. I want to delete /var/log/lastlog and stop any and all logging to the file. I'm aware of the security implications. This logging needs to stop to preserve my backup strategy. I've made a change to /etc/pam.d/login which I was told would disable logging to /var/log/lastlog, but it does not appear to work as /var/log/lastlog keeps growing. # Prints the last login info upon succesful login # (Replaces the `LASTLOG_ENAB' option from login.defs) #session optional pam_lastlog.so Any ideas? EDIT For anyone interested, I use Centrify Express to authenticate my users via LDAP. Centrify Express is "free", but one of the drawbacks is that I can't manage user UIDs via LDAP, so they are given a dynamic UID when they login to a server. Centrify picks some crazy high UID values (so they don't conflict with local users on the server, presumably). /var/log/lastlog is indexed by UID, and grows to accommodate the largest UID on the system. This means that when a Centrify user logs in, they get a UID in the upper-end of the UID range, which causes lastlog to allocate an obscene amount of space, according to the file system. ~$ ll /var/log/lastlog -rw-rw-r-- 1 root root 291487675780 Apr 10 16:37 /var/log/lastlog ~$ du -h /var/log/lastlog 20K /var/log/lastlog More Into --- Sparse Files

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

< Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >