Search Results

Search found 6660 results on 267 pages for 'usb recognition'.

Page 244/267 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >

• Lenovo L440 won't boot into Debian installation CD or Debian-installed HDD

  - by Spencer B Liberto

  I have a Lenovo L440 and a Lenovo X61. I want to install Debian Wheezy on thee L440. This morning, the L440 could successfully boot into Windows 8 from it's hard drive. I created an installation of Wheezy on a USB flash drive with Unetbootin. I created an installation CD of Wheezy with Unetbootin. The X61 can successfully boot into the flash drive. The X61 does not have a CD drive. I have attempted to boot from the live CD and the flash drive from the L440's boot menu. In both cases, the screen fades to black, and then returns me to the boot menu with no error message. I removed the L440's hard drive, and installed it in the X61. I then successfully installed Wheezy onto the hard drive from the flash drive. I'm able to boot into the Wheezy hard drive on the L440. After replacing the hard drive into the L440. I booted from the hard drive from the boot menu. Once again, the screen fades to black, and then returns me to the boot menu with no error message. What's the deal?

  Read the article

• Formatting an external HDD stuck at 70%

  - by mahmood

  My external HDD which is a 250GB WD (powered by USB) seems to have problem! Whenever i try to copy some files, it stuck while copying. I decided to format it. So I used windows tool and performed the format (not quickly) however at nearly 70% it stuck. Then I decided to perform a low level format with lowlevel. Again it stuck at 70%. I endup that the HDD has bad sector. So is there any tool that mark the bad sectors and bypass them? It is not very reasonable to through 250GB because of some bad sectors! P.S: I saw a similar topic but there were no conclusion there either. The smart data is Attribute, raw value, value, threshold, status Read Error Rate, 50, 200, 51, OK Spin-Up Time, 3275, 154, 21, OK Start/Stop Count, 2729, 98, 0, OK Reallocated Sectors Count,0, 200, 140, OK Seek Error Rate, 0, 100, 51, OK Power-On Hours (POH), 1057, 99, 0, OK Spin Retry Count, 0, 100, 51, OK Recalibration Retries ,0, 100, 51 , OK Power Cycle Count, 1385, 99, 0, OK Power-off Retract Count, 425, 200, 0, OK Load /Unload Cycle Count,12974, 196, 0, OK Temperature, 43, 43, 0, OK Reallocation Event Count,0, 200, 0, OK Current Pending Sector Count,23,200, 0, Degradation Uncorrectable Sector Count, 0, 100, 0, OK UltraDMA CRC Error Count,6, 200, 0, OK Write Error Rate/Multi-Zone Error Rate,0,100,51, OK It seems that the most important thing is this line Current Pending Sector Count,23,200, 0, Degradation Any idea on that?

  Read the article

• PC won't boot after hanging during Windows 8 automatic repair [closed]

  - by Mun

  I've got a custom built PC using an ASUS P5E motherboard and Intel Q6600 CPU. I plugged in my mp3 player to the USB port yesteday, and when I came back to the machine after about an hour or so, the Windows 8 automatic repair message was on the screen. It seemed to stick there for an hour, after which I decided to just hit reset and try and figure out what was going on. However, the machine rebooted to a black screen before even getting to the BIOS, with the monitor lights just blinking indicating there was no signal. Tried powering down completely, waiting a few minutes and then powering back up again with no difference; black screen with monitor lights blinking. Tried leaving it on for a while and then pinging from another machine or accessing it via something like LogMeIn, but everything showed the machine as being offline. There were also no error beeps or anything like that. Also tried unplugging all of the memory and rebooting and that also caused no error beeps. Removed one of the display cards and left the other one in there, and still only a black screen. I'm inclined to think that the motherboard or CPU is fried, but there is no indication of damage on any components and the CPU fan seems to be working fine as it always has, so overheating seems unlikely. It's also plugged into a surge protector. The motherboard also has a green light which still lights up. As everything was still working fine before hitting the reset button during Windows 8 automatic repair screen, at which point everything stopped working, it seems unlikely that this problem is down to component failure. Has anyone else experienced anything like this or have any ideas on what could be causing this behavior?

  Read the article

• BSOD during Cygwin install

  - by Mike Pennington

  I have been running Cygwin (1.7.7) under Windows Vista 64-bit, SP2 for at least a year, and had no problems with my installation at all until today. When I tried to install apt-cyg, I realized that I needed to get the svn client. During the installation of the package dependencies, Vista threw a blue screen of death. I hoped this was a one-time occurrence, so I rebooted into Vista and tried to install svn again; same result. Next I completely removed Cygwin's directory, and all Cygwin registry entries; at this point, I tried reinstalling the base Cygwin system again. During the installation of bash, I got another BSOD: Apologies for the fuzzy pic, I had to shoot with my phone camera. I googled for BSOD and Cygwin and found a post by Dave Korn mentioning that the only reasons Cygwin should cause a BSOD is because of either ioperm.sys or some USB utilities. I have neither on my system. Every time I have tried reinstalling, Vista BSODs; I have not had problems installing any other software packages on this Vista machine. How can I get Cygwin installed again (without reinstalling Vista)?

  Read the article

• How to configure router to give XBox top priority / most bandwidth?

  - by MrSparky

  Hi all - Newbie here so go easy... and apologies in advance if I blow the community etiquette / rules! Here's what I'm trying to do: I have a "D-Link DIR-655 Extreme N" wireless router and an XBox 360 w/ the old-style wireless connection thing (usb attachment)... I want to configure my router / network to give my XBox as much bandwidth as it wants, whenever it wants. I have tried giving the XBox a unique IP (within my network) and then tweaking the router to treat that IP as a top priority application (using the router's QOS stuff). Problem is whenever I turn off the xbox, I can't connect to the network the next time I start it up. It seems the only reliable setting in the XBox is to use "Automatic" for the IP settings within the Network Configuration area. Supposedly the D-Link ships with default settings that attempt to recognize a game console and give it top priority... but i've not seen good results (lots of stuttering / lag when someone else jumps online, etc). Any suggestions? thanks again!

  Read the article

• Access Windows Boot Manager selector when timeout is set to 0?

  - by Kyle Cronin

  I've installed Wubi onto a Windows Vista computer. I've also set the boot timeout to 0: bcdedit /timeout 0 However, now I can't figure out how to get the menu to come up at all! I read on the internets that I had to hold F8 or space when starting up, but they doesn't seem to do anything. Is there a different key or setting I've overlooked? The computer itself is a Dell that's a few months old. The keyboard is USB, but I don't think that's the problem as I can get into the BIOS just fine. Maybe I'm doing it wrong? Am I supposed to hold the keys or rapidly tap them (I've tried both)? If it helps, here's the output from bcdedit: C:\Windows\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=C: description Windows Boot Manager locale en-US inherit {globalsettings} default {current} resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} displayorder {current} {e2484fe7-5e97-11de-84d4-0024e8074422} toolsdisplayorder {memdiag} timeout 0 resume No Windows Boot Loader ------------------- identifier {current} device partition=C: path \Windows\system32\winload.exe description Windows Vista locale en-US inherit {bootloadersettings} recoverysequence {572bcd55-ffa7-11d9-aae0-0007e994107d} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} nx OptIn Real-mode Boot Sector --------------------- identifier {e2484fe7-5e97-11de-84d4-0024e8074422} device partition=C: path \ubuntu\winboot\wubildr.mbr description Ubuntu

  Read the article

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• Problem setting up HP PhotoSmart C4783

  - by ProfKaos

  I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

  Read the article

• Cannot access drive in Windows 7 after scandisk lockup, but can in safe mode....

  - by Matt Thompson

  I ran scandisk on my external USB drive due to the inability to delete a few files. Windows asked me if I wanted to unmount the drive before the scan, warning me that it would be unusable until the scan was finished, and I said yes. During the scan, my machine locked up, and I was forced to reboot the machine. When it came up, I was unable to access the drive, getting an error that "L:is not accessible, access is denied". Comupter Management sees the drive, and has the proper amount of disk space filled. I booted into safe mode, and can access the drive with no problems, and I noticed that in explorer, all the folders have locks on them. I booted back into windows, but still could not access the drive, getting the same error as above. Hovever, if I right click on the drive, select properties, and go to Customize, in the folder pictures ares, I select Choose File, and a window open up, that shows the root of the directory, with all the folder able to be accessed, but again, the icon is the folder icon with a lock on it. I can even copy files from the drive to another. So, the files are not gone, windows can obviously access the drive no matter what it thinks, so there has to be a problem with the flag windows put on the drive when it ran the original scan that failed. I was able to run a scan both in safe mode with no problems, and in windows. In windows, I received the cannot access error the first time I run scan disk on it, but if I try again, it works fine. Any ideas on how to clear the flag that windows set, so I can access the drive normally again?

  Read the article

• How can I find files added to the system within X minutes of a specific time?

  - by Jack W-H

  I have done a fresh install of Mac OS X Mountain Lion today on a new MacBook. Because this was a new install, when I finally got round to configuring some of my own developer things, I was surprised to find some app had installed a binary into /usr/local/bin - a single binary called galileod. Interestingly, I can't find anything online about galileod. I had only installed the bare minimum of software at this point. Looking in the file columns I can see Date Modified was 9th November 2012, but Date Added to the system was today at 17:01. It's now 10:20PM and I can't remember which software I was installing at that point. So how do I find out which other files were installed to the system within, say, 5 minutes either side of 17:01? EDIT: I found out what galileod was by running galileod --help - it is a binary used with Fitbit to communicate with the USB dongle. So that's the mystery solved - but it would still be interesting to know how to find files added within X minutes of a timeframe for future reference.

  Read the article

• Hard Drive benchmark values show write very very slow

  - by John

  I recently started to have issues with my laptop being very slow. I ran a hard drive benchmarking tool (by ATTO) that showed that the write speed was very very slow on my boot drive. I ran the same benchmark on my usb drive and it was 650 times faster than my boot drive when it came to writing. Reading is very fast/normal on both. I swapped out an identical drive and ran the same benchmark. This time the drive showed proper write speed. Thinking that I had a hard drive going bad I cloned the old one onto the new one. I managed to clone the problem too. Anyone have any ideas on what in WinXP SP3 might be causing the write issues? I am on a corporate network and we have commercial anti-virus software installed. (AVG I think) I regularly run defraggler and have about 40 gig free on a 100 gig drive. The machine has 4 gigs of memory. Any ideas? TIA J

  Read the article

• I can't connect to my network, except in safe mode

  - by eidylon

  My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

  Read the article

• Best way to attach 96 tb to workstation

  - by user994179

  I'm running a workstation with dual xeon 5690's (12 physical/24 logical cores), 192 gb of ram (ie, maxed-out), Windows 7 64bit, 5 slots for adapter cards, and 1 tb of internal storage, with 5 more internal bays available. I have an app that creates data files totaling about 88 tbs. These are written once every 14 months, and the rest of the time the app only needs to read them; and 95% of the reads are sequential reads of huge chunks of data. I have some control over how big the individual files are, but ideally they would be between 5 and 8 tbs. The app will be reading from only one drive at a time, and the nature of the data is such that if (when) a drive dies I can restore the data to a new disk from tape. While it would be nice to be able to use the fastest drive/controllers available, at this point size matters more than speed. After doing lots of reading, I am leaning toward buying a bunch of cheap 2tb drives and putting them into a bunch of cheap enclosures. All this stuff is going into my home office, so I need to avoid the raised floor/refrigerated approach. My questions: Is the cheap drive/enclosure solution the best one for this situation? Given the nature of the app and the way the data is used, does RAID make sense? If so, which one? For huge sequential reads, would Usb 3.0 and eSata be a wash performance-wise? For each slot available on the workstation, can I hook up an enclosure that can hold multiple drives? Or is it one controller per drive? If I can have multiple drives on one controller, am I essentially splitting the bandwidth (throughput)? For example, if I have a 12 bay enclosure, is the throughput of the controller reduced by a factor of 12? Are there any Windows 7 volume/drive/capacity limits I should be aware of? Thanks

  Read the article

• Optimal file system type and mount options for an rsnapshot dedicated drive

  - by Nimmy Lebby

  We have an external USB 2 drive that we are using as a backup drive for our configuration. We use rsnapshot for the backups. It uses a few standard commands for managing snapshots: rm -rf: deletes expired snapshots mv: moves older snapshots down a slot cp -al: duplicates last snapshot to new slot rsync -a --delete --numeric-ids --relative: synchronizes new snapshot As you could see by the log below, the majority of the time is spent on the rm -rf and the cp -al steps: [25/Dec/2010:14:00:02] rsnapshot hourly: started [25/Dec/2010:14:00:02] echo 21012 > /var/run/rsnapshot.pid [25/Dec/2010:14:00:02] rm -rf /mnt/extdrive/snapshots/hourly.5/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.4/ /mnt/extdrive/snapshots/hourly.5/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.3/ /mnt/extdrive/snapshots/hourly.4/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.2/ /mnt/extdrive/snapshots/hourly.3/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.1/ /mnt/extdrive/snapshots/hourly.2/ [25/Dec/2010:14:15:48] cp -al /mnt/extdrive/snapshots/hourly.0 /mnt/extdrive/snapshots/hourly.1 [25/Dec/2010:14:23:32] rsync -a --delete --numeric-ids --relative /etc /mnt/extdrive/snapshots/hourly.0/sm4/ [25/Dec/2010:14:23:52] touch /mnt/extdrive/snapshots/hourly.0/ [25/Dec/2010:14:23:52] rm -f /var/run/rsnapshot.pid [25/Dec/2010:14:23:52] rsnapshot hourly: completed successfully My questions: I'm currently using ext4 for the filesystem. Maybe this is not the best choice from those available in Red Hat. Anyone have any recommendations that would speed up the process? The partition's mount options are sync,dirsync 1 2. Is there a way to optimize this since it's solely used for rsnapshot? Of course, reasoning would be greatly appreciated.

  Read the article

• Desktop virtualization

  - by gurpal2000

  Is there currently a proper Type 1 "desktop" hypervisor? Either free or not? This is just for tinkering around at home on some beefy Phenom machines. Basically i want to be able to run say 2 OSs on the same PC but without loading windows or a heavy flavour of linux and then use a hotkey to switch between them. I should get full performance out of them. So do i need something better than vmware workstation and/or virtualbox. I think these are "Type 2"? I already run VMWare w/s and VBox but is there a more performant solution? I saw a YouTube video from Citrix where a laptop was running XP and Vista. With the touch of a hot key they could switch between them. There was no visible underlying OS (there might be a hypervisor)? I have access to Citrix XenDesktop 3 enterprise edition evaluation. I realise this isn't for desktops but can i achieve my goal (geekiness) ? If i use the free XenServer 5.5.0 how do my client PCs access windows/linux/whatever from the xenserver? Is it via a thin client RDP type application? If so if there one for both windows and linux? Also if i do use XenServer can i use USB in either direction? What is Citrix receiver can i use that for (3) ? If so, is there some hotkey i can configure? whatever client is used to access the server software (whether it be on a different server or local) can i get full opengl/directx acceleration? what about Xen? i tried the Xen LiveCD but no clue as how to configure it. As you can see much confusion. Any help/pointers welcome. Cheers.

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• Magnetic Stripe Reader over Terminal Server has random Uppercase/Lowercase nonsense

  - by Peter Turner

  The Magnetic Stripe Reader that I'm using and testing is just supposed to be sending keystrokes. Unfortunately, it seems to randomly be sending upper case and lower case keystrokes, sometimes substituting % for 5 and ^ for 6 and vice versa. (If you've ever programmed for a magnetic strip reader, you know that's not a good thing.) Is there something in the RDP protocol that causes this? I've got kind of a convoluted system, running XP inside virtualbox on Fedora 11 RDP'ed into a win2k3 server. It works on the XP VM and it doesn't work on the RDP'ed one. What's weirder, is that I'm not even emulating the USB drivers for my Mag Card Reader. Linux is sending keystrokes straight in to windows, and MSTSC on windows XP is sending crap to the Win2k3 server. I'm 99% certain this isn't a problem with the card reader, it has nothing to do with my programming either. (I get the same junk coming into notepad that I get coming into our software [that's why I didn't ask on SO]). And, it works with rdesktop programs other than MSTSC.exe! Needless to say, I'm in need of some RDP Guruship.

  Read the article

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• Libvirt / QEmu Machine Fails and Refuses Restart Because of Memory Allocation Errors

  - by Elmar Weber

  I'm having a problem with libvirt. On a system restart all virtual machines (VMs) are started without a problem and keep running. Then at some point in time a set of machines shuts down according to their log. When I try to restart the machine, I'm getting an error that the memory allocation failed, although more than enough memory is free. server ~ # free total used free shared buffers cached Mem: 16176648 16025476 151172 0 285432 950300 -/+ buffers/cache: 14789744 1386904 Swap: 0 0 0 server ~ # virsh start zimbra error: Failed to start domain zimbra error: Unable to read from monitor: Connection reset by peer server ~ # tail -n 4 /var/log/libvirt/qemu/zimbra.log LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 3072 -smp 2,sockets=2,cores=1,threads=1 -name zimbra -uuid d05ddb7a-83c4-a77b-d8bc-a322648520cf -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/zimbra.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -drive file=/var/lib/libvirt/images/zimbra.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0,bootindex=1 -netdev tap,fd=19,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=52:54:00:21:a9:ad,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 192.168.1.2:25 -k de -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/2 Failed to allocate 3221225472 B: Cannot allocate memory 2012-07-06 08:42:56.076+0000: shutting down server ~ # uname -a Linux server 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux The system is a Ubuntu 12.04 server. The problem seems to occurs since the last restart, which was due to a number of package upgrades and a kernel upgrade. I tried booting with the previous kernel, the problem persists. I was not able to pinpoint an exact event when the machines fail, they do it at nearly the same time. The last time a duplicity job was running, this was not always the case however. Any suggestions on how to debug this? Best regards, elm

  Read the article

• Backing up server and multiple clients

  - by inquam

  I'm running a Amahi server. It's basically a Fedora14 x64 installation. I'm looking for a good solution to backup my 200GB system drive on the server to an external USB/eSATA drive every night. I looked into using dd but since other things might be running on the server at the same time it didn't feel quite safe. I would like the backups to be incremental so the following backups after the initial one would be quite fast. The backup should also be bootable or prehaps be able to produce a bootable disk after booting from a CD or something. I would also like the server to be able to do similar backups of my clients running Ubuntu, Windows 7 x64, Windows 7 Starter, OSX Lion, Windows XP and so on. So no applications backing up only shared folders or something like that. My guess is a client daemon would have to exist that would lock the system to allow backup of a Windows system drive that can otherwise be quite cranky. Booting up a CD in a crashed client and connecting to the server restoring the latest backup and being up running is my ideal goal. Is there anything out there that would fit these needs?

  Read the article

• Recovering a damaged microSDHC

  - by djechelon

  I just bought from eBay a Kingston 32GB microSDHC that was advertised as defective. The seller said that there could be formatting problems or with transfer of large files. Unfortunately, when I got it, it was a total mess. My Nikon camera doesn't read it at all (OK, maybe it doesn't support 32GB) My Linux laptop doesn't mount it: can't read superblock The same laptop refuses to mkfs.msdos because it failed whilst writing reserved sector The same laptop, under Windows, doesn't read nor format the card HTC HD2 mounts the MMC, allows me to write via USB, but is unable to open the just written files OK, folks, now you would say I would have to go through Paypal complaint... that's not that easy. I consciously bought a half-price card that was known to show some defects, and Paypal complaints take time. Obviously, I can't accept somebody sold me a completely use-less computer decoration. So I'll keep it as last option. My question is Do you know a way, under either Linux or Windows, to thoroughly scan, test and possibly repair memory cards, even if I have to lose some percentage of space because of bad sectors? If I can keep at least half of the card intact it would certainly be fine. I used to do broken sector marking with hard disks in the past. I almost forgot: MONSTR:/home/djechelon # fsck /dev/mmcblk0p1 fsck from util-linux-ng 2.17.2 dosfsck 3.0.9, 31 Jan 2010, FAT32, LFN Read 512 bytes at 0:Input/output error

  Read the article

• A driver (service) for this device has been disabled. Is how the code 32 starts off:

  - by E S

  A driver (service) for this device has been disabled. An alternate driver may be providing this functionality. (Code 32) No drive letter show in device manager, and the dvd/cd is now not useable because it is not seen. This all happened, when i starting using a new, external usb hard drive from Buffalo. I have win 7 64bit. Everything else looks to be working fine. I even out of desperation, tried to hook up, and external dvd that had worked fine in the past. Just too slow and ate up memory, so i never used it. It tries to use the same drives, and when you click to update drivers, it says this is the best one. HELP.... even if i wanted, (WHICH I DON'T), to use the factory win 7 re-installation dvd, how,lol. No drive to install it from in this situation. I am at a lose here, and Buffalo tec was of no help at all. Just said he could not help. Any help would be much appreciated.

  Read the article

• Mouse receiver stopped working after pairing mouse to an unifying receiver

  - by mp19uy

  I bought this mouse, logitech m510, which came with a nano receiver (no-unifying). Yes I know, the mouse is supposed to come with a unifying receiver but I bought it knowing that it won't come on it's original package and it will come with a no-unifying receiver. When I received it, everything worked ok but, after connecting the mouse to another computer using an unifying receiver (that also worked ok, btw), then, when I tried to connect back the mouse to my computer using the no-unifying receiver, I couldn't connect it. I tried everything from removing the batteries and reinstalling the drivers to restarting the computer and trying in different computers, but I couldn't connect them. What I think it happened, is that in fact if you check the documentation of the logitech m510 it says that it works with unifying receivers only, and even more, there is the following article explaining it: http://logitech-en-amr.custhelp.com/app/answers/detail/a_id/18001/~/using-my-m510-with-a-different-usb-receiver So my theory is that the problem was connecting it to a unifying receiver, and now, isn't recognize by another receiver. The receiver (the no-unifying one) itself is recognized by windows, and if I connect the mouse using a unifying receiver, it works. I would like to know if there is any know solution for this or if I can try something else to see if I can solve this.

  Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >