Search Results

Search found 15389 results on 616 pages for 'external js'.

Page 251/616 | < Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >

• Configuring port forwarding for SSH - no response outside LAN [migrated]

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• fax server farm architechture

  - by Brian Postow

  I'm not sure this is the right forum for this, but it's not Stackoverflow so... I'm trying to figure out an architecture to solve the following problem, maybe someone here can help: I have a T1 with 23 fax lines coming into the building. I have a computer (Macintosh XServe) running Hylafax. If I had one POTS line, I'd be done. However, I have no idea how to get the T1 into the Mac... Options I've considered: some sort of PCI T1-modem (Does that exist?) Splitting the T1 into 23 POTS lines and then connecting 23 analog modems to the mac, either via an external modem bank (Do they still make those?) or via some sort of external PCI bank, which will allow me to use more than 2 4-port modem cards. Either the T1 or the split POTS lines going into some intermediate device and then transfering the images over IP, or USB to the mac. Really, any other option I can come up with This has GOT to be a problem that someone has already solved, right?

  Read the article

• Apache Reverse proxy for intranet and other integrated application on intranet

  - by user1433448

  I'm trying to configure a reverse proxy (ssl) with apache 2.2 in Debian Squeeze, but I have some problems, specially with some path absolute and with https I'll try to detail what I have made and what I'm trying to configure I have a server Debian Squeeze with apache2.2 + mod_proxy_html with: # apt-get install libapache2-mod-proxy-html libxml2-dev # a2enmod proxy # a2enmod proxy_http # a2enmod proxy_html # a2enmod headers After that I have configured a virtual host with: reverse_proxy_ssl.conf I'm trying to configure to allow access of our intranet from internet with a reverse proxy (apache that is located in DMZ). With this configuration domain.com/intranet works correctly and we can access to intranet, but we have one problem when from domain.com/intranet we need to use another internal application that is called from intranet with absolute path ( https://192.168.10.25/application/) and from internet appears that try to access with internal ip, and this link es incorrect from external site We only need to access from intranet to multiple internal application that are in external server and we like to restrict to minimal access from internet. All the application that are in the smae server of intranet are working. The second problem is with https and reverse proxy in our firewall appears some errors with packets (not valid packets), and with https seems to work. What can I do to solve this problems (absolute path and ssl problem) Thanks

  Read the article

• Communicating via Command Mode with IBM HS22 IMM via AMM

  - by MikeyB

  On previous model blades that contained a BMC, I was able to communicate from our external management station via pass-through commands to the BMC to do things such as power blades on/off, set VPD parameters, reboot the BMC, etc. Now on the HS22, a bunch of things happen differently. For example, we can no longer use the same pass-through commands to write VPD information pages and have them persist across reboots of the IMM - it looks as though those VPD pages are populated from information contained in the IMM. How do we use the Advanced Settings Utility from an external host to communicate with HS22 IMMs? Alternatively, what TCP Command Mode commands do we need to send to the AMM to communicate with the IMM? For our purposes, we specifically cannot communicate with the IMM from the blade itself. Specific example: When I send a pass-thru IPMI command via the AMM to the blade BMC to write information (such as MTM, Serial) into VPD page 0x10, it persists on blades with a BMC (HS21 for example). I can send the same IPMI command to write data to the VPD page on the HS22, however it does not persist across reboots of the IMM. What IPMI commands do I need to send to the IMM? What IPMI commands are asu sending when it sets the MTM & Serial?

  Read the article

• Apache Proxy Pass and Web Sockets

  - by James

  I'm using Apache with the mod_proxy module to reverse proxy my Node.js application through to port 80, so that we can access it as an internal application. I have a file in sites-enabled which contains this: VirtualHost *:80> DocumentRoot /var/www/internal/ ServerName internal ServerAlias internal <Directory /var/www/internal/public/> Options All AllowOverride All Order allow,deny Allow from all </Directory> ProxyRequests off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8080/ retry=0 ProxyPassReverse / http://localhost:8080/ ProxyPreserveHost on ProxyTimeout 1200 LogLevel debug AllowEncodedSlashes on </VirtualHost> As I said, our application is written in Node.js and we're using socket.io to make use of web-sockets, as our application also contains realtime elements to it. The problem is, mod_proxy doesn't seem to handle web sockets and we get errors when trying to use them: WebSocket connection to 'ws://bloot/socket.io/1/websocket/nHtTh6ZwQjSXlmI7UMua' failed: Unexpected response code: 502 How can we fix this issue and keep sockets working, as the only way we can get it working currently is to access the site via ip:port which we don't want to do. Also, as a side question, how can I get ErrorDocument to work properly? Our error files are stored in /var/www/internal/public/error/ but they seem to get put through the proxy too?

  Read the article

• Setting up subdomain to respond on :443 with apache2

  - by compucuke

  I read through some guides on this and I believe it is possible to have apache respond to a subdomain through ssl. I have domain.com responding on 80 and I do not need domain.com responding on 443. Rather, the only use I have for ssl is for the subdomain sub.domain.com. So my site should be http://domain.com http://www.domain.com https://sub.domain.com https://www.sub.domain.com My CNAME records are as follows sub.domain.com xxx.xx.xx.xxx *.sub.domain.com xxx.xx.xx.xxx The A record exists but should not matter for the example. I set up a separate config file in sites-enabled for sub.domain.com NameVirtualHost xxx.xx.xx.xxx:443 <VirtualHost xxx.xx.xx.xxx:443> SSLEngine on SSLStrictSNIVHostCheck on SSLProtocol -ALL +SSLv3 +TLSv1 SSLCipherSuite ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:-MEDIUM ServerAlias sub.domain.com DocumentRoot /usr/local/www/ssl/documents/ SSLCertificateFile /root/sub.domain.com.crt SSLCertificateKeyFile /root/sub.domain.com.key Alias /robots.txt /usr/local/www/ssl/documents/robots.txt Alias /favicon.ico /usr/local/www/ssl/documents/favicon.ico Alias /js/libs /usr/local/www/ssl/documents/js/libs Alias /media/ /usr/local/www/documents/media/ Alias /img/ /usr/local/www/ssl/documents/img/ Alias /css/ /usr/local/www/ssl/documents/css/ <Directory /usr/local/www/ssl/documents/> Order allow,deny Allow from all </Directory> WSGIDaemonProcess sub.domain.com processes=2 threads=7 display-name=%{GROUP} WSGIProcessGroup sub.domain.com WSGIScriptAlias / /usr/local/www/wsgi-scripts/script.wsgi <Directory /usr/local/www/wsgi-scripts> Order allow,deny Allow from all </Directory> </VirtualHost> Now, it is important to mention that https://domain.com responds with what I have running from script.wsgi above instead of on https://sub.domain.com. It does not respond to sub.domain.com. checking https://sub.domain.com causes a 105 error. This is a DNS error but I am convinced the DNS does not have a problem with the CNAME records, they just point to my IP. Am I doing something that Apache can not do?

  Read the article

• check_snmp with snmpv3 protocol giving "Unkown Report message" error

  - by John

  I'm trying to add a nagios command to use snmpv3 for monitoring printer status messages. When using the check_snmp command, I get the following error: External command error: snmpget: Unknown Report message Here is the command I'm typing in: ./check_snmp -P 3 -H <hostname> -L authPriv -U snmpuser -A snmppassword -X snmppassword -o 1.3.6.1.4.1.11.2.4.3.1.2.0 -C public -d "STRING:" -a MD5 These values for auth key, private key, username, etc all work when using snmpwalk. Can someone enlighten me as to what that error message really means? EDIT: It looks like check_snmp isn't taking my v3 credentials when passing over to snmpget. Here is my input with the verbose option: ./check_snmp -H <hostname> -o 1.3.6.1.2.1.2.2.1.10.1 -C public -m ALL -P 3 -L authPriv -U snmpuser -a MD5 -A snmppassword -x DES -X snmppassword -v And here is the output: /usr/bin/snmpget -t 1 -r 5 -m ALL -v 3 [authpriv] <hostname>:161 1.3.6.1.2.1.2.2.1.10.1 External command error: snmpget: Unknown Report message So I guess now my question would be: why isn't check_snmp passing all the commandline options to snmpget?

  Read the article

• Set up WLAN in 3-level house

  - by Balint Erdi

  I'm having a hard time setting up the network in our house. It has three levels (basement, ground floor, first level). The WLAN is set up by an ASUS RT-N12 router which provides perfect coverage for the ground floor and the basement. However, I set up my "home office" in the basement where the signal barely arrived. So I purchased a TP-Link TL-WA901ND (300 Mbps) Access Point which I set up in the other corner of the ground floor to expand the ASUS router's range. I used the AP's Repeater mode for that. The distance between my computer and the TP-Link AP is 6-7 meters. There is a staircase going down from the ground floor to the basement so there are no solid walls between the computer and the AP. This setup mostly works (I am writing this from the basement) but it is not reliable (the signal strength sometimes goes down to ~40% of the max) sometimes so I wonder if I am doing it correctly or if there is a better way. Screenshot of the router's and the AP's dashboard screen follow: Any comments on what I am doing wrong or hints for improvement are appreciated. Thank you. UPDATE Tried one more thing, setting up the TP-LINK AP in Access Point mode. That way, I can make it use a different SSID. I enabled WDS/Bridge so that it expands the range of the ASUS router (see screenshot). That does not work, either, if I connect to the network set up by the TP-LINK device (PELSTER-2), I can't reach the external network (the Internet). It seems the problem always comes back to this, the TP-LINK does not have access to the external network, whatever its mode of operation.

  Read the article

• Windows 7 Can't Connect to Network Drive on Windows XP

  - by Alex Yan

  I have a Windows XP desktop and a Windows 7 laptop both connected to a TrendNET TEW-432BRP router, which is connected to the Internet. They both have static IPs. The desktop has an external hard drive connected to it. The laptop is wireless and the desktop is wired. I enabled sharing on the external hard drive about two years ago when I bought it. I mapped it as a network drive on the laptop. I think it was yesterday, the laptop just stopped recognizing any of the computers on my network (When I open network, my laptop's the only one on it). I also get an error message "An error occurred while connecting A: to \CERTIFIED-DATA\Expansion Microsoft Windows Network: The network path was not found. The connection has not been restored" when I try to connect to the network drive. Both computers run Avast, and there hasn't been any problems with it. This has happened before but I never figured out why and how to fix it. It's usually fixed when I reinstall the OS of the affected system. Edit: I can't navigate the computer using \\CERTIFIED-DATA. I get a message saying "Windows cannot access \CERTIFIED-DATA. Check the spelling of the name, Otherwise, there might be a problem with your network" I clicked diagnose on the message and it failed to find anything wrong I clicked diagnose on my wireless connection, and it just keeps trying to check if something is wrong with the connection I can ping it successfully

  Read the article

• Backup data rate on Raspberry Pi maxing out at 5 Mb/s. Why?

  - by bastibe

  I set up my Raspberry Pi as a Time Machine, as documented here. At the moment, the Raspberry Pi is connected to my MacBook Pro using a direct Ethernet cable. Also, an external hard drive (laptop drive) is connected to the Raspberry Pi using the USB port. However, backups are pretty slow. Activity Monitor claims that the Network is transferring a very steady 5 Mb/s, where my Time Capsule is transferring up to 8 Mb/s with a lot of fluctuation. The Raspberry Pi self-reports (top) that its CPU is only half-used, with about equal parts afpd, usb-storage and jbd2/sda1-8. Thus, I think that the processing power of the Raspberry Pi does not seem to be the problem here. To me, this looks like there is some kind of bottleneck that maxes out at 5 Mb/s thus potentially having my backups run at less than their potential speed. To the best of my knowledge, this might be the afp-daemon, the usb-bus or the external hard drive. So, my question is, how could I identify the true culprit and what can I do about it?

  Read the article

• New router messed up server 2003 setup...

  - by Aceth

  Hey, We were sent a new 2wire router today configured it as best we can to match the old bt voyager. We've also got X static IP's. We've manage to get our webserver on one of the new IP's public facing. then we use a hardware firewall which is in a DMZ again with a different static IP. This firewall then is our gateway for our internal LAN. with a few servers etc. The problem we're having is only our PDC (primary Domain controller which has exchange 2003 on) can't ping externally even an external IP. We've connected laptops to the 2wire router and obtain a private ip 192.168.1.X and it works fine can ping etc. our other servers with an internal ip behind the firewall can ping out fine. We've connected to the firewalls logging console and the pings from the server are allowed through so its fine there. The server in question is a Windows server 2003 R2 Enterprise SP2 + Exchange 2003 Server doesn't have firewall turned on. it has static private IP .. gateway is pointing to the right one External Static IP is routing fine inwards We've ran out of ideas .. help??

  Read the article

• How do I get netcat to accept connections from outside the LAN?

  - by Chris

  I'm using netcat as a backend to shovel data back and forth for a program I'm making. I tested my program on the local network, and once it worked I thought it would be a matter of simply forwarding a port from my router to have my program work over the internet. Alas! This seems not to be the case. If I start netcat listening on port 6666 with: nc -vv -l -p 6666, then go to 127.0.0.1:6666 in a browser, as expected I see a HTTP GET request come through netcat (and my browser sits waiting in vain). If I go to my.external.ip.address:6666, however, nothing comes through at all and the browser displays 'could not connect to my.external.ip.address:6666'. I know that the port is correctly forwarded, as www.canyouseeme.org says port 6666 is open (and when netcat is not listening, that its closed). If I run netcat with -g my.adslmodem's.local.address to set the gateway address, I get the same behavior. Am I using this command line option correctly? Any insight as to what I'm doing wrong?

  Read the article

• Robocopy launches and then hangs/just sits there

  - by NateO

  I'm setting up an archive process to store old files on an external hard drive. The computer in question is running Windows 7 Pro 32bit. We have a server folder with 150,000+ files in it, most of which are pretty small (below 200k). I'm trying to use robocopy in a batch file to do this. It was working fine the other day, now all it does upon launch is sit there. It shows me all the options and whatnot, and also lists the number of files in the directory and the directory itself, but it never gets past that line. If I switch the destination to the local C drive, it eventually starts copying files. Is there something in my batch file that needs to change? Or could there be a problem with the external Western Digital drive that I'm using? The WD drive currently is holding about 175,000 files. Here is the one line batch file I have: robocopy "\\cgifp01\Prepress\Public\ImportedPDF" "E:\OldFiles" *.* /R:2 /W:10 /MINAGE:15 /MOV /B /XJ /XF "blank_test.pdf" Thanks for any tips or ideas. Nate

  Read the article

• Static noise in headphones

  - by John Murdoch

  I have a Asus P6T based system. I was using the on-board sound (plugging in Logitech X-230 2.1 analog speakers in the green "front speakers" 3.5mm analog output, then plugging in my headphones in that). I was quite happy with the sound quality (didn't hear any static noise if volume was turned down to my normal listening level). Then about a week ago I started having terrible static noise from the left channel, and no normal audio on that left channel. Right channel had more static noise than usual but did have a bit of sound. I tried using the AC'97 in front of my case but that seemed to have no signal. I decided my on-board sound card has gone bad and bought an internal sound card to replace it (Startech 7.1Ch PCI). This fixed the "no sound from left channel problem", but I had much more audible static noise. I decided the card was low quality and/or it had interference from all the other things happening inside the computer case, and bought a Sweex SC016 external USB sound card. But even with that I have static noise in headphones. Positioning the USB sound card differently doesn't seem to help. Trying the other analog outputs (e.g., surround) doesn't help. The static noise in all cases is proportional to the volume. I have tried different headphones, but the situation is situation though perhaps the flavour of the static noise changes slightly. So what are my options? a) Get another, more expensive, external USB sound card hoping the quality will improve? b) Get another, more expensive, internal sound card (PCIe 1x perhaps) hoping the quality will improve? c) Get a dedicated DAC box? d) Get some Hi-Fi earphones? Suggestions? tl;dr - Two different sound cards both still have static noise in headphones.

  Read the article

• Server 2008 NAT Internet Not Working

  - by Jack

  I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

  Read the article

• SharePoint Business Connectivity Services (BCS) Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'

  - by g18c

  I am running SharePoint 2010 with SQL 2012, I am trying to get Business Connectivity Services (BCS) running but I am facing a double-hope authentication issue. Everytime I try to connect to the external BCS list created in SharePoint designer, I get the error Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. In the event viewer on the SQL server I see a login failure for an anonymous user from the SP server IP address. Background information below: I have enabled Kerberos under SharePoint Central admin. I have the following AD domain accounts: SP_Farm - main website pool SP_Services - for SharePoint services (including BCS) SQL_Engine - SQL database engine I then created the following with SetSPN: SetSPN -S http/intranet mydomain\SP_Farm SetSPN -S http/intranet.mydomain.local mydomain\SP_Farm SetSPN -S SPSvc/SPS mydomain\SP_Farm SetSPN -S MSSQLSvc/SQL1 mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1.mydomain.local mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1:1433 mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1.mydomain.local:1433 mydomain\SQL_DatabaseEngine I then delegated the AD accounts for any authentication protocol to the following: SP_Farm - SP_Farm (http service type, intranet) SP_Farm - SQL_DatabaseEngine (MSSQLSvc, sql1) SP_Service - SP_Service (SPSvc) SP_Service - SQL_DatabaseEngine (MSSQLSvc, sql1) I have also checked the WFE is being logged on to with Kerberos, with the WFE server event log showing event ID 4624 with Kerberos authentication, this is OK. The SQL is also showing connections authenticated as Kerberos from the WFE with the following query: Select s.session_id, s.login_name, s.host_name, c.auth_scheme from sys.dm_exec_connections c inner join sys.dm_exec_sessions s on c.session_id = s.session_id Despite the above, credentials are not passed from the client through the SharePoint server to the SQL server, only the anonymous account is used. I get the following error in the WFE server for 'BusinessData' ID 8080: Could not open connection using 'data source=sql1.mydomain.local;initial catalog=MSCRM;integrated security=SSPI;pooling=true;persist security info=false' in App Domain '/LM/W3SVC/1848937658/ROOT-1-129922939694071446'. The full exception text is: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. If I set a username and password with the Secure Store Service and set the external list to use the impersonated credentials, the list works. Any ideas what I have missed and what can be tried next?

  Read the article

• Unable to communicate with EWS from Exchange Server

  - by kschieck

  We are currently running a 2 server exchange environment with Edge services on their own. We are in the process of trying to deploy a piece of software that uses the EWS API which has brought me to this form, the software ties into the EWS service and uses it to forward messages (this is failing). Using the software error logs I have found that accessing EWS from the exchange server is not possible. From my work machine and an external address I can type the following https ://webmail.companyname.com/ews/exchange.asmx and be prompted for a username and password, once I enter credentials I get a screen full of information from services.wsdl. The problem is when I try the same URL from the exchange server and get the credentials prompt I cannot get past it. Even with the same credentials that work externally and from my desk it just keeps looping around. Capture from software log (11:41:32.6415 000017e4 System.Net.WebException: The request failed with HTTP status 401: Unauthorized.) I have also found the same results when trying https://webmail.companyname.com/ Autodiscover /Autodiscover.xml . Environment Information Server 2008 STD 64bit Exchange 2007 SP1 Purchased Cert – webmail.companyname.com I have also confirmed that all services have the proper internal and external URL’s. Any help would be appreciated.

  Read the article

• Reverse proxy apache to weblogic problem

  - by Zlatoroh

  Hello I have apache 2.2 server and welogic 11g running on web server. Apache is set for revers proxy on port 8080, weblogic serves two web pages and it's on port :7001 first page: localhost:7001/e-SPP/app second page: localhost:7001/e-sprejem/app I would like to access this two pages with apache like so: localhost:8080/e-SPP/app localhost:8080/e-sprejem/app Listen 8080 ServerName localhost:8080 <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPreserveHost On RewriteEngine On <Location /e-SPP/app> ProxyPass localhost:7001/e-SPP/app ProxyPassReverse localhost:7001/e-SPP/app </Location> <Location /e-sprejem/app> ProxyPass localhost:7001/e-sprejem/app ProxyPassReverse localhost:7001/e-sprejem/app </Location> This configuration opens my pages bust it's black anw white because CSS and JS aren't loaded! Path to the css over proxy looks like this : localhost:8080/e-SPP/css/style.css which doesn't open the CSS if I change the port to 7001 the it works !!! localhost:7001/e-SPP/css/style.css What should I do that CSS and JS are loaded? Interesting is favicon which is being loaded http://localhost:8080/e-SPP/images/new/favicon.gif Thanks for your help!

  Read the article

• Do registry issues with Win7 persist through a recovery from a system image?

  - by user59089

  So I need a bit of advice, please; here's my situation: I have 1) a system image on an a brand new external 1 TB SATA drive, that I managed to successfully capture before my 2) primary system drive went down. I realize this is a fairly simple matter of buying a new primary drive and performing the recovery to the fresh disk...however, the issue is that I believe Win7 was also having some significant issues of its own--basically, Update unable to install updates, and Backup continually ditching the auto backup schedule. I'd been trying to address those issues when my system was still working, but it's been so fruitless, I'm convinced a Win7 re-install would be best, and now I'm concerned that if I was in fact having what I believe are likely registry-related issues before, that these will persist through a recovery--would that likely be correct? I'm mainly worried about recovering my files, so if I did a full recovery from the image, should I be able to then access my individual files, and copy them manually to an external drive, so I can then do a full re-install of Win7? Sory if this seems obvious, but I've never done a recovery before and just trying to make sure there's no red flags with what I have in mind...

  Read the article

• Robocopy silently missing files

  - by John Hunt

  I'm using Robocopy to sync data from our server's hard disk to an external disk as a backup. It's a pretty simple solution but pretty much the best/easiest one we could come up with - we use two external disks and rotate them offsite. Anyway, here's the script (with the comments taken out) that I'm using to do it. It works very well, it's quick and almost 100% complete - however it's acting pretty strange with a few files (note company name has been changed in paths to protect the innocent): @ECHO OFF set DATESTAMP=%DATE:~10,4%/%DATE:~4,2%/%DATE:~7,2% %TIME:~0,2%:%TIME:~3,2%:%TIME:~6,2% SET prefix="E:\backup_log-" SET source_dir="M:\Company Names Data\Working Folder\_ADMIN_BACKUP_FILES\COMPA AANY Business Folder_Backup_040407\COMPANY_sales order register\BACKUP CLIENT FOLDERS & CURRENT JOBS pre 270404\CLIENT SALES ORDER REGISTER" SET dest_dir="E:\dest" SET log_fname=%prefix%%date:~-4,4%%date:~-10,2%%date:~-7,2%.log SET what_to_copy=/COPY:DAT /MIR SET options=/R:0 /W:0 /LOG+:%log_fname% /NFL /NDL ROBOCOPY %source_dir% %dest_dir% %what_to_copy% %options% set DATESTAMP=%DATE:~10,4%/%DATE:~4,2%/%DATE:~7,2% %TIME:~0,2%:%TIME:~3,2%:%TIME:~6,2% cscript msg.vbs "Backup completed at %DATESTAMP% - Logs can be found on the E: drive." :END Normally the source would just be M:\Comapany name data\ but I altered the script a bit to test the problem. The following files in the source are not copied to the dest: Someclient\SONICP~1.DOC Someclient\SONICP~2.DOC Someclient\SONICP~3.DOC However, files in the same directory named: TIMESH~1.XLS TIMESH~2.XLS are copied. I'm able to open the files that aren't copied with no trouble at all, and they certainly weren't opened when I ran robocopy so it's not a locking issue. Robocopy is running as administrator so it's not a permissions issue. There's no trace these files were even attempted to be copied as there are no errors being output in the log or in my command prompt. Does anyone have any suggestions as to what this might be? Busted hard disk? Cheers, John.

  Read the article

• Unix Permissions: Enable access to files no matter the user?

  - by TK Kocheran

  I've been using Linux for a long time and I still am completely in the dark about how file permissions really work. With that in mind, does anyone have any books or thorough guides I could read to really understand things completely? I've done my fair share of sysadminning, so I know the easy stuff like making directories readable and writable, making files executable, and changing the owner of a file, but on sharing files across users, I'm lost. Here's my main problem. I have a number of machines across which I intend to synchronize my music library. I've been using Unison for a while now and it's a great choice as I can easily run it over SSH on my local network which I just set up. Win-win. Up until this point, I've been synchronizing computers using a 2TB external hard drive. (computer 1 unisons to HD, computer 2 unisons to HD, etc.) This is tedious at best, especially since I encrypted the drive, making it a huge hassle to hook it up to all of my machines and sync it. Anyway, the drive is running ext4 (in TrueCrypt), so it maintains all Unix filesystem info like owners and groups. I just set up a new machine and just Unison'd it to get the music on it, and I realized that now, all of my permissions are fubar. I had to run Unison as root since that was the only way I could get the files to come off of the external drive. Apparently, since I'm using a different user name on this machine than my usual "rfkrocktk" across all machines, this essentially throws a huge wrench in the gears. Here's my use case. This laptop has two effective users, "leandra" and "rfkrocktk". I want to share music between these two users, so I symlinked /home/rfkrocktk/Music to point to /home/leandra/Music. How do I (a) allow both users access to read/write/delete files in this folder, and (b) keep everything nicely in sync without messing up file ownership?

  Read the article

• Windows 7 64-bit installation from alternative media (no DVD/USB Flash drive)

  - by Niels Willems

  Greetings I currently have Windows 7 x86 installed on my computer. I want to install Windows 7 x64 on a different partition on my computer. However there is a little issue, I cannot run the x64 install from Windows 7 x86 which I currently have. I was planning to Install Windows 7 x64 on another partition to then boot up from that partition to install it on the partition I actually want my OS on. Once that is complete I could just format the partition from the Windows 7 x64 that I didn't need anymore. But the installer will not run from the x86 version of Windows 7 even though I do not want to upgrade that Windows directly. The reason I'm doing this in such a weird way is that my optical drive is broken and I'm really not into buying a new one since I would use it like once every year or so. I also don't have a USB Flash Drive which is big enough to hold the installation files. As far as I'm aware I cannot use an external hard drive such as this one, which I do have. Are there any alternatives in which I can install Windows 7 x64 or am I forced into buying a USB Flash Drive or new optical drive? Thank you in advance for your replies. Edit: This picture shows my current partitions on my laptop. I want to get Windows 7 x64 on the C partition but have to install it first on the F partition to then boot up the F partition windows to format C and install x64 on that one. My external drive is J. Edit 2: No alternative computer which has a DVD drive, install files are located on an iso from MA3D. To install my 32 bit version I mounted the ISO in Daemon Tools to replace my Windows Vista but since I cannot run 64 bit into my 32 bit OS this doesn't work.

  Read the article

• Problem hosting server behing personal router

  - by Venkatesh Hodavdekar

  I recently bought the domain name lucidcontraptions.com and want to host the website from home. I have a D-Link router in which I have set up my personal virtual server correctly. My application server is Apache 2.2. The server works perfectly with the following settings: External IP: 207.172.xx.xx. Public port: 8888 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx:8888/ the server works perfectly and my Apache page shows up without any issues, both from inside the intranet as well as outside. This setting would not work out for me as I am not allowed port numbers in my DNS management. Now when I tweak the settings to the following: External IP: 207.172.xx.xx. Public port: 80 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx/ the server works perfectly and my Apache page shows up without any issues, BUT ONLY FROM INSIDE THE INTRANET. This page does not show up for people outside the intranet.

  Read the article

• ISA Server dropping packets as it believes they are spoofed

  - by RB

  We have ISA Server 2004 running on Windows Server 2003 SP2. It has 2 NICs - one internal called LAN on 192.168.16.2, with a subnet of 255.255.255.0, and one external called WAN on 93.x.x.2. The default gateway is 93.x.x.1 (our modem). This machine also accepts VPN connections. We are having a problem with a scanner, which is trying to save a scan into a network share. Every time we try to scan, ISA Server logs the following Denied Connection Log type: Firewall service Status: A packet was dropped because ISA Server determined that the source IP address is spoofed. Rule: Source: Internal ( 192.168.16.54:1024) Destination: Internal ( 192.168.16.255:137) Protocol: NetBios Name Service Pinging 192.168.16.54 from the ISA Server works fine. In ISA Server, going into Configuration → Networks, there are 5 Networks : - External (inbuilt) - Internal (defined as 192.168.16.0 → 192.168.16.255) - Local Host (inbuilt) - Quarantined VPN Clients (inbuilt) - VPN Clients (inbuilt) Finally, under Network Connections → Advanced → Advanced Settings..., the connections are in the following order : - LAN - WAN - [Remote Access Connections] If we try to scan onto a workstation it works fine. Please let me know if you need any more info - many thanks. RB.

  Read the article

• Webmin ADSL module

  - by expatcm

  I was wondering if the Webmin ADSL module is going to help me solve a problem .... but I cannot find any documentation telling me what the module does ..... Any ideas? What I am hoping is that it will solve a problem .... I am just in the process of setting up a Debian server. I will use the DHCP server as part of the Debian setup to manage the lan IP addresses. I want to turn off the external DHCP server which is part of the Linksys ADSL modem / router and use just the modem. The challenge I have is knowing what I need to do in order to get the public DNS on the eth1. When I turn off the DHCP on the modem / router not a lot happens apart from no longer being able to access the settings .......... So I am looking at this Webmin module and wondering if it is to manage the ADSL connection and find the public DNS address .... The local DHCP server is working well for the lan, I am just stuck for the external DNS.

  Read the article

< Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >