Search Results

Search found 12790 results on 512 pages for 'port islander 2009'.

Page 256/512 | < Previous Page | 252 253 254 255 256 257 258 259 260 261 262 263  | Next Page >

• Gigabyte H55N-USB3: No video on HDMI

  - by newt

  I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

  - by Gabble

  I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

  Read the article

• Is it bad to redirect http to https?

  - by jasondavis

  I just installed an SSL Certificate on my server. I use a web hosting panel called ZPanel that is an open source project. It then set up a redirect for all traffic on my domain on Port 80 to redirect it to Port 443. In other words, all my http://example.com traffic is now redirected to the appropriate https://example.com version of the page. The redirect is done in my Apache Virtual Hosts file with something like this... RewriteEngine on ReWriteCond %{SERVER_PORT} !^443$ RewriteRule ^/(.*) https://%{HTTP_HOST}/$1 [NC,R,L] My question is, are there any drawbacks to using SSL? Since this is not a 301 Redirect, will I lose link juice/ranking in search engines by switching to https? I appreciate the help. I have always wanted to set up SSL on a server, just for the practice of doing it, and I finally decided to do it tonight. It seems to be working well so far, but I am not sure if it's a good idea to use this on every page. My site is not eCommerce and doesn't handle sensitive data; it's mainly for looks and the thrill of installing it for learning. UPDATED ISSUE Strangely Bing creates this screenshot from my site now that it is using HTTPS everywhere...

  Read the article

• Adjust iptables

  - by madunix

  cat /etc/sysconfig/iptables: # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d X.0.0.Y -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp -s X.Y.Z.W --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp -s M.M.M.M --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 21 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT I have the above following IPtables on my linux web server(Apache/MySQL), I want to have the following: Block any traffic from multiple IP's to my web server IP1:1.2.3.4.5, IP2:6.7.8.9 ..etc Limiting one host to 20 connections to 80 port, which should not affect non-malicious user, but would render slowloris unusable from one host. Limit MYSQL port 3306 access on my server only to the following IP range A.B.C.D/255.255.255.240 Block any ICMP traffic.

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• Doesn't work Nginx + SSI

  - by boopidoopi

  I have some problems. Nginx doesn't work with SSI. Nginx listens 80 port (frontend), apache2 listens 81 port (backend). That is my nginx configurations: server { listen 80; server_name test.dev www.test.dev; error_log /var/log/nginx/error.log debug; log_subrequest on; location / { ssi on; proxy_pass http://localhost:81; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 15m; client_body_buffer_size 128k; } } SSI include in test.dev index.php: <!--# include virtual="http:test.dev/test.html" -- When I open test.dev/index.php I see clean page. In page source: <!--# include virtual="http:test.dev/test.html" -- So how to enable SSI in nginx? Can you help me?

  Read the article

• FreeBSD: problem with Postfix after updating LDAP

  - by Olexandr

  At the server I installed openldap-server, at this computer open-ldap client has already been installed. Version of openldap-client (2.4.16) was older then new openldap-server (2.4.21) and the version of client has updated too. OpenLDAP-client works with postfix on this server and after all updates postfix cann't start again. The error when postfix stop|start is: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix" At the category with libraries is libldap-2.4.so.7, but libldap-2.4.so.6 is removed from the server. When I want to deinstall curently version of openldap-client, system write ===> Deinstalling for net/openldap24-client O.K., but when I start "make install" system write: ===> Installing for openldap-sasl-client-2.4.23 ===> openldap-sasl-client-2.4.23 depends on shared library: sasl2.2 - found ===> Generating temporary packing list ===> Checking if net/openldap24-client already installed ===> An older version of net/openldap24-client is already installed (openldap-client-2.4.21) You may wish to ``make deinstall'' and install this port again by ``make reinstall'' to upgrade it properly. If you really wish to overwrite the old port of net/openldap24-client without deleting it first, set the variable "FORCE_PKG_REGISTER" in your environment or the "make install" command line. *** Error code 1 Stop in /usr/ports/net/openldap24-client. *** Error code 1 Stop in /usr/ports/net/openldap24-client. Updating of ports doesn't help, and postfix writes error: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix"

  Read the article

• Windows network routing

  - by fabianvilers

  Hi! I'm working by my customer premises and they let me connect my private laptop on a dedicated Wi-Fi for internet access. It's nice for external consultants. The only issue is that we can't connect on a remote server on port 25. I suppose this policy is set up to avoid infected computers sending spam from their network. As you can have guessed, this is something weird that I can't send mail at all. Fortunately, I've a 3G cell phone that I can connect by Bluetooth on my laptop. So when I want to send an e-mail, I have to disconnect from Wi-Fi, connect my phone, send the e-mail, disconnect phone and reconnect Wi-Fi. Kinda overhead. My question is: how can I tell Windows 7 to use the Wi-Fi for every out connection, but if it's a connection on port 25, use the cell phone network? With this solution, I could let my phone connected all day without having to switch again and again. Thanks a lot for your anwwers. Fabian

  Read the article

• Cisco 851 (IOS) router: FastEthernet 4 (WAN) got the shutdown flag.

  - by cjavapro

  At a customer location there was a Cisco 851 router (which uses IOS). The PCs on location were all of a sudden unable to connect. We came on site and found that FastEthernet 4 (the WAN port) was "administratively down". We ran these commands to resolve it config t interface fa4 no shutdown exit exit write Now the mystery is how the shutdown flag got there in the first place? The router was on battery backup... but during the outage it was power cycled by the customer. It is possible that there was a short outage by the ISP and that the power cycle caused the shutdown flag to come up. There may have been a hack or an attack pattern that caused the shutdown flag to come up. There may have been a hack or an attack pattern that the router to become unavailable and then caused the shutdown flag to be added on startup. Question: Does anybody have any clues? or at least remember that they had a shutdown flag come up on their WAN port also?

  Read the article

• How do I tell Websphere 7 about a front end load balancer so that re-directs are handled correctly?

  - by TiGz

  On WebLogic 11G I can use the console to set the FrontendHost and FrondendPort on a server or on a cluster so that re-directs are handled correctly and end up resolving to the front end load balancer instead of the local host. The MBeans associated with this on WebLogic are, for example: MBean Name com.bea:Name=AdminServer,Type=WebServer,Server=AdminServer Attribute Name FrontendHost Description The name of the host to which all redirected URLs will be sent. If specified, WebLogic Server will use this value rather than the one in the HOST header. Sets the HTTP frontendHost Provides a method to ensure that the webapp will always have the correct HOST information, even when the request is coming through a firewall or a proxy. If this parameter is configured, the HOST header will be ignored and the information in this parameter will be used in its place. Type java.lang.String Readable / Writable RW How is the same thing achieved under Websphere 7? Follow up info: So I have 2 use cases actually. One is that I have a web app running under WebSphere on host A on port 9002 and a LB running on host B at port 80, when I visit the home page of the app via the LB on http://hostb/app the app redirects my browser to http://hostb:9002/app and it 404's I think this is WebSphere's fault but I guess it could be the app's fault? The second is that the web app in question needs to send emails containing URls that the customer can click on to get back into the web app - obviously this needs to be via the LB. On WebLogic the app uses MBeans to derive the LB url and I was hoping to use a similar mechanism on WebSphere.

  Read the article

• IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

  - by NVRAM

  I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

  Read the article

• Cannot make bind9 forward DNS query to subdomain unless recursive enabled

  - by PP.

  I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

  Read the article

• How to diagnose issue between mobo, RAID, and SSD cache drive? [migrated]

  - by goober

  Background This issue is happening on my custom-built desktop. Relevant specs: Motherboard: ASUS P8Z68-V PRO Utilizing Intel RST technology (application that uses unused SSD as cache) Processor: Intel core i7-2600k (not overclocked) HDDs: RAID1 of 2x Seagate Barracuda 1TB (ST31000524AS) (RAID performed via z68 chipset) Machine has run fine for ~1 year with no issues, and has been well-maintained (dust, etc.) What Happened Random Freezing issues -- intermittent Looked at the RST application screen to see that the acceleration cache was listed as "unavailable" -- recommended that I power down and reconnect the drive. Reconnected the drive to no avail. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Now, the freeze happens whenever loading something particularly data-driven (a video, a game, etc.) Steps Attempted Reconnected the drive to no avail. Updated Intel RST software to v. 11.6.0.1030 to see if that made a difference. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Connected the drive as its own volume. Formatted it, ran disk check errors -- all seems fine. Reconnected the drive and selected it again as the cache drive. Now, what happens when there is a freeze: Machine freezes I am unable to perform any command Screen then goes black I hit the reset button During boot, all drives show as "Disabled" and I am told no volume can be found I then hit the reset button (or power off/on) again. Either the next time (or sometimes after repeating this once more), the metadata cache is reconstructed and the system boots fine, showing the SSD as a cache. Question I believe this is an issue with the SSD itself, but how can I be sure since connecting it separately appeared to show no problems? I want to make sure it's not an issue with the motherboard, SATA ports, etc.

  Read the article

• Apache Named Virtual Hosts and HTTPS

  - by Freddie Witherden

  I have an SSL certificate which is valid for multiple (sub-) domains. In Apache I have configured this as follows: In /etc/apache2/apache2.conf NameVirtualHost <my ip>:443 Then for one named virtual host I have <VirtualHost <my ip>:443> ServerName ... SSLEngine on SSLCertificateFile ... SSLCertificateKeyFile ... SSLCertificateChainFile ... SSLCACertificateFile ... </VirtualHost> Finally, for every other site I want to be accessible over HTTPS I just have a <VirtualHost <my ip>:443> ServerName ... </VirtualHost> The good news is that it works. However, when I start Apache I get warning messages [warn] Init: SSL server IP/port conflict: Domain A:443 (...) vs. Domain B:443 (...) [warn] Init: SSL server IP/port conflict: Domain C:443 (...) vs. Domain B:443 (...) [warn] Init: You should not use name-based virtual hosts in conjunction with SSL!! So, my question is: how should I be configuring this? Clearly from the warning messages I am doing something wrong (although it does work!), however, the above configuration was the only one I could get to work. It is somewhat annoying as the configuration files have an explicit dependence on my IP address.

  Read the article

• What differences are there between "home" switches and "professional" switches?

  - by pjreddie

  Our radio station uses a PtP wireless system to stream our radio and TV signals from our studio up a hill to our transmitter. We have been having problems with warbly sound and drop outs that come from some point in this system. An engineer that occasionally visits the station thinks it could be the switches we use on each side of the PtP wireless system to connect the PtP devices to the encoders and decoders and wants us to get two of these switches: http://www.amazon.com/Netgear-JGS516-ProSafe-16-Port-Ethernet/dp/B0002CWPOK/ref=dp_return_1 The encoder/decoder setup only streams 8Mbps total so it seems like the switches we have should not be stressed out, unless they are causing sufficient latency to degrade the performance of the encoder/decoder. At each end of the connection we only have 4 connections, is there any reason we couldn't get a cheaper, "home" quality switch like this: http://www.amazon.com/D-Link-DGS-1005G-5-Port-Gigabit-Desktop/dp/tech-data/B003X7TRWE/ref=de_a_smtd Is there a significant difference that we would notice in terms of latency between these two switches? How much does the quality of the switch actually matter in this scenario? Any help is appreciated, feel free to ask questions if anything needs clarification. Thanks

  Read the article

• Is this a good starting point for iptables in Linux?

  - by sbrattla

  Hi, I'm new to iptables, and i've been trying to put together a firewall which purpose is to protect a web server. The below rules are the ones i've put together so far, and i would like to hear if the rules makes sense - and wether i've left out anything essential? In addition to port 80, i also need to have port 3306 (mysql) and 22 (ssh) open for external connections. Any feedback is highly appreciated! #!/bin/sh # Clear all existing rules. iptables -F # ACCEPT connections for loopback network connection, 127.0.0.1. iptables -A INPUT -i lo -j ACCEPT # ALLOW established traffic iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # DROP packets that are NEW but does not have the SYN but set. iptables -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # DROP fragmented packets, as there is no way to tell the source and destination ports of such a packet. iptables -A INPUT -f -j DROP # DROP packets with all tcp flags set (XMAS packets). iptables -A INPUT -p tcp --tcp-flags ALL ALL -j DROP # DROP packets with no tcp flags set (NULL packets). iptables -A INPUT -p tcp --tcp-flags ALL NONE -j DROP # ALLOW ssh traffic (and prevent against DoS attacks) iptables -A INPUT -p tcp --dport ssh -m limit --limit 1/s -j ACCEPT # ALLOW http traffic (and prevent against DoS attacks) iptables -A INPUT -p tcp --dport http -m limit --limit 5/s -j ACCEPT # ALLOW mysql traffic (and prevent against DoS attacks) iptables -A INPUT -p tcp --dport mysql -m limit --limit 25/s -j ACCEPT # DROP any other traffic. iptables -A INPUT -j DROP

  Read the article

• Basic IPTables setup for OpenVPN/HTTP/HTTPS server

  - by Afronautica

  I'm trying to get a basic IPTables setup on my server which will allow HTTP/SSH access, as well as enable the use of the server as an OpenVPN tunnel. The following is my current rule setup - the problem is OpenVPN queries (port 1194) seemed to be getting dropped as a result of this ruleset. Pinging a website while logged into the VPN results in teh response: Request timeout for icmp_seq 1 92 bytes from 10.8.0.1: Destination Port Unreachable When I clear the IPTable rules pinging from the VPN works fine. Any ideas? iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A FORWARD -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT iptables -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT iptables -A INPUT -j REJECT iptables -A FORWARD -j REJECT

  Read the article

• How to setup bindings for development IIS 7.5 with lot of sites

  - by Antonio Bakula

  I am a programmer in a small ASP.NET shop with very little expirience in server administration, and I have to setup IIS 7.5 to host lot of sites on newly installed windows server 2008 R2, these sites are test "clones" for sites on "real" web server and they should be accessible only in local network (domain). Developers should add new sites for our new customers. Project managers use this server to check progress and test new sites and new features, QA people have to have access to this site and test before we copy it to the "real" web server. Developers only have access to IIS console, in fact they can use RDP to test server with their developer domain credentials and permissions, also developers are local admins on that machine (tester). On our previous server I used different port numbers for each site. That worked but don't like this solution, I would prefer to use subdomains. But here are the problems: manually adding DNS records is not an option because we do not wont that developers have to administer domain DNS server, and currently this had to be done with domain administrator credentials. Is there a some way to add DNS record automatically ? I tried to add DNS record for subdomains on test server with wildcard (*.tester) and that seems to work for some time but that change coused some bad problems in our domain network and admin forbid me to mess with DNS, he said that I have to add DNS record for every subdomain manually and that I can not use wildcards, and there is nothing that I can do about it, mainly for "politicall" reasons :( obviously our admin is pretty much uncooperative, outsorced from different organization and I can't do anything about that. can I add another DNS server on that machine ? What must be setup on clients machines to "tell" them to use domain DNS server and tester domain server ? So please I need someone to give me some advice, what should I do ? Is different port numbers only option left ? Thanks !

  Read the article

• Multiple copies off the same printer on Windows 7 from PrintUIEntry

  - by Kev

  I currently have a number of bat files which work perfectly fine on Windows XP which install the same printer multiple times with a number of finisher options set - e.g. after running the bat file below I would end up with four printers in the printer drop down called Sharp Kits Printer - A4 Single Sided Sharp Kits Printer - A4 Single Sided Stapled Sharp Kits Printer - A4 Duplex Stapled Sharp Kits Printer - A4 Duplex which all have there options configured in the relevant way. I have amended on Windows 7 to point to correct INF file and printer name in the INF files - a single printer installs fine. However when I run the complete batch file only the first printer in it is installed - occassionally the later ones flash up in the GUI but then vanish when you press F5 and are still missing after a reboot. SET QUEUENAME=http://192.168.7.123:631/printers/Sharp700 SET PPD=J:\DRIVERS\Printers\MX700-Win7-64\SJ1JWENG.INF SET PPDENTRYNAME=SHARP MX-M700U PPD J: cd "\DRIVERS\Printers\MX700-Win7-64" SET NICENAME="Sharp Kits Printer - A4 Single Sided" SET PREFS="J:\SCRIPTS\Printers-Win7-64bit\Sharp_SINGLE_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... SET NICENAME="Sharp Kits Printer - A4 Duplex" SET PREFS="J:\SCRIPTS\Printers\Sharp_DUPLEX_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... I have tried adding the "/u" paramater to the end, I have changed the "/n" paramater to be different (e.g. n1, n2,n3 etc) - both of these result in the same. I have also tried to change the port (/r) to have "_1" (etc) on the end like the GUI would but this errors as the port doesn't exist. Is it possible to do this on Windows 7, and if so how?

  Read the article

• iptables rules for DNS/Transparent proxy with ip exceptions

  - by SlimSCSI

  I am running a router (A Netgear WNDR3700 if that matters) with dd-wrt. For content filtering I am using OpenDNS. I wanted to make sure a user could not bypass OpenDNS by putting in their own name servers, so I have a rule to catch all DNS traffic. iptables -t nat -A PREROUTING -i br0 -p all --dport 53 -j DNAT --to $LAN_IP I did have one computer on the network I wanted to allow past OpenDNS filters. On that machine I manually set the name servers, and created another rule to allow it to pass iptables -t nat -I PREROUTING -i br0 -s 192.168.1.2 -j ACCEPT This worked well. Today, I installed a transparent proxy (squid) on the router and added these rules: iptables -t nat -A PREROUTING -i br0 -s $LAN_NET -d $LAN_NET -p tcp --dport 80 -j ACCEPT iptables -t nat -A PREROUTING -i br0 -s ! $PROXY_IP -p tcp --dport 80 -j DNAT --to $PROXY_IP:$PROXY_PORT iptables -t nat -I POSTROUTING -o br0 -s $LAN_NET -d $PROXY_IP -p tcp -j SNAT --to $LAN_IP iptables -I FORWARD -i br0 -o br0 -s $LAN_NET -d $PROXY_IP -p tcp --dport $PROXY_PORT -j ACCEPT This also works, however the 192.168.1.2 address does not get routed through squid. How can I have 192.168.1.2 (and maybe others in the future) by-pass the port 53 rules, but not the port 80 rules?

  Read the article

• LVS / IPVS difference in ActiveConn since upgrading

  - by Hans

  I've recently migrated from an old version of LVS / ldirectord (Ultra Monkey) to a new Debian install with ldirectord. Now the amount of Active Connections is usually higher than the amount of Inactive Connections, it used to be the other way around. Basically on the old load balancer the connections looked something like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 12 252 -> 10.84.32.22:0 Masq 1 18 368 However since migrating it to the new load balancer it looks more like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 313 141 -> 10.84.32.22:0 Masq 1 276 183 Old load balancer: Debian 3.1 ipvsadm 1.24 ldirectord 1.2.3 New load balancer: Debian 6.0.5 ipvsadm 1.25 ldirectord 1.0.3 (I guess the versioning system changed) Is it because the old load balancer was running a kernel from 2005, and ldirectord from 2004, and things have simply changed in the past 7 - 8 years? Did I miss some sysctl settings that I should be enforcing for it to behave in the same way? Everything appears to be working fine but can anyone see an issue with this behaviour? Thanks in advance! Additional info: I'm using LVS in masquerading mode, the real servers have the load balancer as their gateway. The real servers are running Apache, which hasn't changed during the upgrade. The boxes themselves show roughly the same amount of Inactive Connections shown in ipvsadm.

  Read the article

• Embedded Windows XP

  - by Kyle

  My company acquired a brake press for bending large structural steel plates. We received it second hand and it came with an embedded copy of windows XP. Now for the part that's driving me nuts: plug and play has been turned off, also accessibility options has been disabled. What does this mean for me? Keyboards will not work! Nothing that plugs into a USB port will work and it does not have a CD ROM drive. I have tried to turn on plug and play using the on screen keyboard but it is not there since accessibility options is turned off. I would just get an updated copy of the the embedded OS but they come from Sweden and are extremely expensive. I assume there has got to be a way to get a USB devices to work. We need to get a wifi adapter on it so I can use team viewer and remotely configure it for our needs. Things to keep in mind: There is no keyboard so everything has to be done with the mouse There is no PS2 port for a keyboard just a mouse. Odd. I am 5 states away from this location and have been working with a tech who is physically installing the machine. System 32 seems to be missing A LOT of files, the tech told me there is only 8 folders in there and no other files (I don't even understand how Windows is running like this). If anyone has ANY ideas I would appreciate it, I am unsure where to go from here.

  Read the article

• Can't ssh from CentOS 6.5 to SUSE LINUX 10.1

  - by Pavel Tankov

  We have a quite old installation of SUSE LINUX 10.1 (i586) in the office. The problem shortly: I can successfully ssh to it from machines in the same LAN (192.168.1.0) and not from others (that are in 10.23.0.0). The SuSE has SSH server openssh-4.2p1-18.12. I have ruled out the firewall and hosts.allow and hosts.deny files. When my ssh login attempt fails, here is what the logs say: on the client: $ ssh -vvv 192.168.1.5 OpenSSH_5.3p1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.1.5 [192.168.1.5] port 22. debug1: Connection established. debug1: identity file /home/nbuild/.ssh/identity type -1 debug1: identity file /home/nbuild/.ssh/identity-cert type -1 debug1: identity file /home/nbuild/.ssh/id_rsa type -1 debug1: identity file /home/nbuild/.ssh/id_rsa-cert type -1 debug1: identity file /home/nbuild/.ssh/id_dsa type -1 debug1: identity file /home/nbuild/.ssh/id_dsa-cert type -1 on the server: Aug 21 16:34:25 serverhost sshd[20736]: debug3: fd 4 is not O_NONBLOCK Aug 21 16:34:25 serverhost sshd[20736]: debug1: Forked child 20739. Aug 21 16:34:25 serverhost sshd[20736]: debug3: send_rexec_state: entering fd = 7 config len 403 Aug 21 16:34:25 serverhost sshd[20736]: debug3: ssh_msg_send: type 0 Aug 21 16:34:25 serverhost sshd[20736]: debug3: send_rexec_state: done Aug 21 16:34:25 serverhost sshd[20739]: debug1: rexec start in 4 out 4 newsock 4 pipe 6 sock 7 Aug 21 16:34:25 serverhost sshd[20739]: debug1: inetd sockets after dupping: 3, 3 Aug 21 16:34:25 serverhost sshd[20739]: debug3: Normalising mapped IPv4 in IPv6 address Aug 21 16:34:25 serverhost sshd[20739]: Connection from 10.23.1.11 port 44340 The above log on the server is when I enable DEBUG3 log level. However, with the default log level (INFO), the only thing the server logs is this: Aug 21 16:38:32 serverhost sshd[20749]: Did not receive identification string from 10.23.1.11 Any hints? I feel I've tried everything already.

  Read the article

• Server Intermittently Inaccessible Externally (but Accessible Internally Continuously)

  - by nicorellius

  I have a CRM on a server on a network. We have a static IP and another server outward facing. We use port-forwarding to map to the CRM, so that when you go to the IP or the FQDN, you get to the CRM: xxx.xxx.xxx.xxx crm.example.com Internally, we can access the CRM by going to crm or crm.example.com Lately, I've been noticing that accessing the server from outside the network times out or gives 503, bad gateway. During that time, I can also SSH (different port, so this works) into the outward facing computer and access the server just fine. I have a robot monitoring the site and indeed via HTTP monitoring the site is going down periodically. I looked through the Apache server access and error logs and nothing stuck out at me so I'm a bit confused as to what could be going on. I also searched the access logs for 503 and found nothing. When I run tracert from outside the network, it appears the packets basically make it through the wider area servers (Comcast city and county servers) and end up dropping at the CRM server's front step. I'm tempted to replace the server because it is older and underpowered but it would be nice to know what is going on. Any ideas what to do next?

  Read the article

< Previous Page | 252 253 254 255 256 257 258 259 260 261 262 263  | Next Page >