Search Results

Search found 19350 results on 774 pages for 'address book'.

Page 263/774 | < Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >

  • Port forwarding not working?

    - by rphello101
    I'm trying to set up an Apache Server to be accessed publicly. I'm using a Netgear R4500 router hooked up to a Motorola SB6121 modem. I can access my server on my computer by typing in my IP address. After following the instructions to forward port 80 so I can access the server from other computers, it does not work (see image). I get "This webpage is not available". I am forwarding to the IP address of my computer. Using this Network Port Scanner Tool, it says "80/tcp filtered http", which, as I understand it, means forwarding did not work correctly. In my Apache httpd file, I have: ServerName 192.168.1.13:80 and Listen 192.168.1.13:80 Anyone know what's wrong or have something I can try? click to enlarge

    Read the article

  • forwardfor information is missing

    - by FAFA
    I use following configuration to load balance https connections, using haproxy 1.4.8. SSL offloading is done by apache. listen ssl_to_waf 192.168.101.54:443 mode tcp balance roundrobin option ssl-hello-chk server wafA 192.168.101.61:444 check listen ssl_from_waf 192.168.101.61:445 balance roundrobin option forwardfor server webA 192.168.101.46:80 check For HTTP requests this works great, requests are distributed to my Apache servers just fine. But for HTTPS request, I lose the "forwardfor" information. I need to save the client IP address. How can I use HAproxy to load balance across a number of SSL servers, allowing those servers to know the client's IP address?

    Read the article

  • BSOD constantly with same ntoskrnl.exe error and disk indicator is frozen

    - by Sheep
    BSOD constantly and the disk indicator is frozen. Error do not happen immediately, usually an hour after boot up. Here is the Minidump: Bug Check Code = 0x00000124 Caused By Driver = ntoskrnl.exe Caused By Address = ntoskrnl.exe+4b094c Crash Address = ntoskrnl.exe+4b094c Seems to be hardware problem, but I checked RAM, no error. I have two HDs installed, system is on SSD, data is on HDD. Checked SSD with the properties-tools-error-checking , no error. Re-installed several times, still happens even after removed HDD. Configuration: SSD: Crucial M4-CT064M4SSD2 with Firmware 0009 Intel HM65 CPU: i7-2630QM The SSD is set correctly, SATA III 6Gb/s enabled, and everything worked perfectly for nearly a year.

    Read the article

  • What to do if I get ping results for non-existing hosts?

    - by bublegumm
    When I am pinging non-existing host like 'zzz' or 'qwerty' I am getting the following result Pinging zzz.kanisa.com [209.62.20.200] with 32 bytes of data: Reply from 209.62.20.200: bytes=32 time=60ms TTL=46 Reply from 209.62.20.200: bytes=32 time=66ms TTL=46 It looks like a virus to me. But I was unable to find a solution on web. Any ideas how to fix it? Even more ridiculous results with nslookup C:\> nslookup google.com Server: google-public-dns-a.google.com Address: 8.8.8.8 Non-authoritative answer: Name: google.com.kanisa.com Address: 209.62.20.200 How to get rid of it?

    Read the article

  • What settings need to be changed to allow EC2 instances to use Amazon's Route 53 for DNS?

    - by ks78
    I have a number of Amazon EC2 instances, all running Ubuntu, which I'd like to configure to use Amazon's Route 53. I setup a script, following Shlomo Swidler's article, but ran into script-related issues, which were answered here. Now, I have the script working, but my instances are still not able to access Route 53's DNS. By this I mean, they are not able to resolve hostnames to IP addresses. My instances are currently configured with the DNS server IP address Amazon pushes out to them by default, does that need to be changed when using Route 53? I'm also IP-restricting my instances using the Security Groups. Could that be the problem? Is there a certain IP address or port I should open to allow communication with Route 53? It seems that DNS requests should be originating from my instances so the Security Groups shouldn't be an issue, but I've been wrong before. If anyone has any ideas, I'd really appreciate it.

    Read the article

  • lots of dns requests from China, should I worry?

    - by nn4l
    I have turned on dns query logs, and when running "tail -f /var/log/syslog" I see that I get hundreds of identical requests from a single ip address: Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#10856: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#44334: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#15268: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#59597: query: mydomain.de IN ANY + The frequency is about 5 - 10 requests per second, going on for about a minute. After that the same effect repeats from a different IP address. I have now logged about 10000 requests from about 25 ip addresses within just a couple of hours, all of them come from China according to "whois [ipaddr]". What is going on here? Is my name server under attack? Can I do something about this?

    Read the article

  • Remote Desktop Connection over VPN on mac

    - by Diego Faria
    I'm trying to connect to a Windows computer on over a VPN connection using Remote Desktop connection. I opened Network on mac and created a new connection. Interface: VPN. VPN Type: PPTP. I filled the inputs for server address, account name, password and applied. I connect the VPN and it connects. I open Remote Desktop Connection and put the IP of the machina i want to connect but it dont connect, a problem occurs saying that the machina may be turned off and etc. But in a windows machine I can connect there and the machine is up and running. On my mac I ping to the ip address that a want to connect and it has no response. I think that the vpn have a problem, is there a way for me to certificate that i am on the vpn network ? Whats going on?

    Read the article

  • Run database checks but omit large tables or filegroups - New option in Ola Hallengren's Scripts

    - by Greg Low
    One of the things I've always wanted in DBCC CHECKDB is the option to omit particular tables from the check. The situation that I often see is that companies with large databases often have only one or two very large tables. They want to run a DBCC CHECKDB on the database to check everything except those couple of tables due to time constraints. I posted a request on the Connect site about time some time ago: https://connect.microsoft.com/SQLServer/feedback/details/611164/dbcc-checkdb-omit-tables-option The workaround from the product team was that you could script out the checks that you did want to carry out, rather than omitting the ones that you didn't. I didn't overly like this as a workaround as clients often had a very large number of objects that they did want to check and only one or two that they didn't. I've always been impressed with the work that our buddy Ola Hallengren has done on his maintenance scripts. He pinged me recently about my old Connect item and said he was going to implement something similar. The good news is that it's available now. Here are some examples he provided of the newly-supported syntax: EXECUTE dbo.DatabaseIntegrityCheck @Databases = 'AdventureWorks', @CheckCommands = 'CHECKDB' EXECUTE dbo.DatabaseIntegrityCheck @Databases = 'AdventureWorks', @CheckCommands = 'CHECKALLOC,CHECKTABLE,CHECKCATALOG', @Objects = 'AdventureWorks.Person.Address' EXECUTE dbo.DatabaseIntegrityCheck @Databases = 'AdventureWorks', @CheckCommands = 'CHECKALLOC,CHECKTABLE,CHECKCATALOG', @Objects = 'ALL_OBJECTS,-AdventureWorks.Person.Address' EXECUTE dbo.DatabaseIntegrityCheck @Databases = 'AdventureWorks', @CheckCommands = 'CHECKFILEGROUP,CHECKCATALOG', @FileGroups = 'AdventureWorks.PRIMARY' EXECUTE dbo.DatabaseIntegrityCheck @Databases = 'AdventureWorks', @CheckCommands = 'CHECKFILEGROUP,CHECKCATALOG', @FileGroups = 'ALL_FILEGROUPS,-AdventureWorks.PRIMARY' Note the syntax to omit an object from the list of objects and the option to omit one filegroup. Nice! Thanks Ola! You'll find details here: http://ola.hallengren.com/  

    Read the article

  • Squid throws error, The requested URL could not be retrieved

    - by Supratik
    Sometimes I am getting the following error The requested URL could not be retrieved While trying to retrieve the URL: http://groups.google.com/ The following error was encountered: Unable to determine IP address from host name for groups.google.com The dnsserver returned: Refused: The name server refuses to perform the specified operation. This means that: The cache was not able to resolve the hostname presented in the URL. Check if the address is correct. Your cache administrator is root. What could be the reason for the above error ? Regards Supratik

    Read the article

  • Cannot Enter Repro Admin Web Interface at Port 5080

    - by aqua
    I have followed the instructions on this website www.rtcquickstart.org to set up my firewall, DNS settings, TLS, and have installed the TURN server and repro proxy as instructed, and have restarted repro. However, I am not able to access the web interface of repro on port 5080, either at localhost:5080 / 127.0.0.1:5080 or at the server's IP address: IPADDRESS:5080 (I have set the server's IP for binding in repro.config). I get the browser error message: 'Unable to connect to server' whenever trying to connect to the web interface via port 5080. I initially had Apache2 installed, which loaded pages correctly at port 80 / address root, and when checked it 'listened' at port 5080 after it was configured in /etc/apache2/ports.conf, however the repro web interface still did not work at port 5080. I have tried uninstalling Apache2 in case that was conflicting with repro's web server, but the problem persists, and testing port 5080 now shows that nothing is 'listening' on port 5080. I have tried reinstalling / purging repro but it has not helped. My router is correctly set to allow all ports; port 5080 is open and forwarding correctly. I can connect to the internet and ping all websites through the server and everything else is working correctly. I would be gateful if anyone could offer advice on how to solve this problem.

    Read the article

  • Windows doesn't get access to internet though linux easily does

    - by flashnik
    We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

    Read the article

  • iPhone always assigned wrong ip

    - by Ashley Ray
    for some reason most of the time my iPhone connects to the home network the ip address seems wrongly assigned as it 'loses connection' even even with strong reception. If I change the ip address to a static from 168.2.10 to 168.2.15 works fine until it appears to renew back to the prior. I am using a power-plug extender from the modem to router. Then have a laptop Printer playstation tv and another iPhone that always connect fine. The modem also has a crappy wireless which I haven't connected any devices to. I'm sure the forum will have a simple answer!

    Read the article

  • Webserver insists on opening "blog1.php" instead of "index.php"

    - by pepoluan
    I'm at my wits' end. I have just ripped out a website and in the process of rebuilding everything. Previously, the 'home page' of the website is a blog, with the address "www.mydomain.com/blog1.php". After exporting everything, I deleted the whole directory, and -- based on request -- immediately create a blog/ directory. The idea is to get the blog back up as soon as possible, and temporarily redirect people accessing www.mydomain.com to the blog. Accessing the blog via http://www.mydomain.com/blog/ works. So I put in an index.php file containing a (temporary) redirect to the blog's address. The problem: The server insists on opening blog1.php instead of index.php. Even after we deleted all the files (including .htaccess). And even putting in a new .htaccess file with the single line of DirectoryIndex index.php doesn't work. The server stubbornly wants blog1.php. Now, the server is actually a webhosting, so I have no actual access to it. I have to do my work via cPanel. Currently, I work around this issue by creating blog1.php; but I really want to know why the server does not revert to opening index.php. Did I perhaps miss some important settings in the byzantine cPanel menu page?

    Read the article

  • A "tinkered" PC can ping by IP, not by hostname. How to fix?

    - by aitchnyu
    Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

    Read the article

  • Spam bot constantly hitting our site 800-1,000 times a day. Causing loss in sales

    - by akaDanPaul
    For the past 5 months our site has been receiving hits from these 4 sites below; sheratonbd.com newsheraton.com newsheration.com newsheratonltd.com Typically the exact url they come from looks something like this; http://www.newsheraton.com/ClickEarnArea.aspx?loginsession_expiredlogin=85 The spam bot goes to our homepage and stays there for about 1 min and then exist. Luckily we have some pretty beefy servers so it hasn't even come close to overloading our servers yet. Last month I started blocking the IP address's of the spam bots but they seem to keep getting new ones everyday. So far I have blocked over 200 IP address's, below are a few of the ones I have blocked. They all come from Bangladesh. 58.97.238.214 58.97.149.132 180.234.109.108 180.149.31.221 117.18.231.5 117.18.231.12 Since this has been going on for the past 5 months our real site traffic has started to drop, and everyday our orders get lower and lower. Also since these spam bots simply go to our homepage and then leave our bounce rate in analytics has sky rocketed. My questions are; Is it possible that these spam bots are affecting our SEO? 60% of our orders come from natural search, and since this whole thing has started orders have slowly been dropping. What would be the reason someone would want to waste resources in doing this to our site? IP's aren't free and either are domain names, what would be the goal in doing this to us? We have google adwords but don't advertise on extended networks nor advertise in Bangladesh since we don't ship there so they are not making money on adsense. Has anyone experienced anything similar to this? What did you do and what was the final out come?

    Read the article

  • Distribute outgoing connections among multiple IPs configured on the same NIC

    - by cedivad
    I have a NIC with 2 aliases on it. The network interface has 3 IPs configured on it. Think about it like this: i can ping the same server by hitting .100 .101 and .102. I want the source address of the outgoing connections to be distributed among these ip. So if i have 3 opened connections, one connection will have result as having an IP address ending with .100, the other two should result as having as ip addresses .101 and .102. I'm using FreeBSD but I think this question to be Linux-Like wide.

    Read the article

  • Google Docs: Tie the Form with a Spreadsheet to email addresses and responses?

    - by Nick Gorbikoff
    Hello. I'm just trying to figure out if I'm doing something wrong or it's not possible. I created a small form ( I'm trying to get current mailing addresses from my friends and relatives - since I lost my address book) and it ties to a Google Spreadsheet. I sent out a sample to my work address - filled out a form and saved it. However when I go to see the responses - in a spreadsheet - it has a time stamp but it has no email associated with a response - so I don't know who made it ( well in this case I know it's me - but when you have 100 replies?) I understand - it may be great for anonymous surveys - but in this case I'd like to know who responded with what - and I don't wan to make them fill out Email and First Name & Last Name - I already have this information. Any suggestions?

    Read the article

  • Should I quit using Ifconfig?

    - by Zhen
    With the servers that mount Infiniband cards, when I use the ifconfig command I have the warning: Ifconfig uses the ioctl access method to get the full address information, which limits hardware addresses to 8 bytes. Because Infiniband address has 20 bytes, only the first 8 bytes are displayed correctly. Ifconfig is obsolete! For replacement check ip. Should I quit using ifconfig? It is deprecated in favor of ip command? Or it will be update in the near future.

    Read the article

  • IPv6 tunnels - any easy way to turn them on and off?

    - by Rob Hoare
    I've set up a tunnelbroker.net (Hurricane Electric) IPv6 tunnel from my laptop running 12.04. Works fine, and allows me to test the dual-stack configuration on my remote webservers etc. until native IPv6 is available on my ISP. However, there are times when I don't want the tunnel. For example if I'm accessing something that requires an IPv4 address in my own country rather than the Tunnelbroker tunnel endpoint, or if I'm away from the local IPv4 tunnel endpoint, or if I simply want to test without IPv6. Is there a simple way to disable and then re-enable the IPv6 tunnel, without rebooting? For context, here's what's in my /etc/network/interfaces (NNN replaces numbers): auto he-ipv6 iface he-ipv6 inet6 v4tunnel endpoint 216.218.NNN.NNN address 2001:470:NNN:NNN::2 netmask 64 up ip -6 route add default dev he-ipv6 down ip -6 route del default dev he-ipv6 Is there a network manager application (gui or command line) to selectively enable/disable parts of /etc/network/interfaces, or IPv6 in general? I found even by commenting out that out (and reloading networking) it's tough to get the IPv6 to go away. A "tunnel on/off" button in networking would be great, like using a VPN.

    Read the article

  • How to test DNS glue record?

    - by Sunnz
    Hello I have just set up a DNS server for my domain example.org with 2 name servers ns1.example.org and ns2.example.org. I have attempted to set up a glue record for ns1 and ns2 at my registrar. It seems to work for now when I do a dig example.org but when I do a whois example.org it lists ns1.example.org and ns2.example.org but not their IP address which should be set up as a glue record. So I am wondering how do I check for the existence of a glue record? Do I do it with whois? I have seen .com and .net whois records that have both the domain name as well as the IP address for the name servers, is .org different? What's the proper way to test this? Thanks.

    Read the article

  • Samsung i780 networking problem

    - by Infinity
    Hello guys! Maybe this is not the right place to ask this, but I give a try for it. Please don't rate it down, just ignore it if you don't like. So I have a Samsung i780 mobile phone and I would like to use the internet through my wireless router. I have connected to it. I got an IP address. My laptop is also connected to the same wireless network and I can ping the mobile phone and I get answer. When I open the internet explorer and enter an address it says that it cannot connect to the internet. I have googled very much, but can't find the problem. What do you think, what is the solution?

    Read the article

  • Where is debian storing its network settings?

    - by user13743
    I have a debian machine that is supposed to have a static ip, but insists on getting its address from the DHCP server. Here's this settings file: $> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.1.99 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 Yet $> sudo /etc/init.d/networking restart Reconfiguring network interfaces...done. $> sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:e0:03:09:05:2e inet addr:192.168.1.205 Bcast:255.255.255.255 Mask:255.255.255.0 ... Where is it being told to use dhcp?

    Read the article

  • IIS 7.5 and ASP.NET MVC Routing

    - by m__
    I'm running an ASP.NET MVC 3 application on an IIS 7.5 server (my development server). When I set up my production server something goes wrong. Serving the same application binaries, using the same web.config file and connecting to the same database I get different results. Something must be wrong with my IIS configuration, but what? Here's an example I visit http://mysite.com/An/AspNetMvc/Routed/Address/1 and everything works I visit http://mysite.com/An/AspNetMvc/Routed/Address/1.1 works on my development server but not on my production server which gives the following error HTTP Error 404.0 - Not Found The resource you are looking for has been removed, had its name changed, or is temporarily unavailable. Module IIS Web Core Notification MapRequestHandler Handler StaticFile Error Code 0x80070002 Somehow the URL is served as a static file on my production server which led me to investigate my IIS Handler Mappings, but without luck.

    Read the article

  • SPF record doesn't work (not sure which DNS server to tweak)

    - by Ion
    Problem: Google (and perhaps others) marks our emails as SPF neutral. Let me give you some background about the setup: initially got a dedicated server (Hetzner) with Plesk installed to host a domain/web application, let's say: bigjaws.com. Plesk automatically creates a DNS zone for it with some records for the various services it provides out of the box, e.g. webmail.bigjaws.com as a CNAME to bigjaws.com to provide Horde/whatever, etc. Let me point out four relevant of these records (where XXX.XXX.XXX.158 is our dedicated IP): bigjaws.com. A XXX.XXX.XXX.158 mail.bigjaws.com. A XXX.XXX.XXX.158 bigjaws.com MX (10) mail.bigjaws.com. bigjaws.com. TXT v=spf1 +a +mx -all The above records are not(?) valid anymore though, because after using this dedicated server for a while, our site got bigger and bigger so we decided to move our operations over to AWS (EC2, RDS, ELB, etc), but we retained the mail functionality as is, i.e. emails from [email protected] are sent by connecting to our dedicated server where Plesk takes care of things. This was decided in order not to setup anything from scratch. Of course for all DNS-related things we now use Route53. In Route53 I have the following records: mail.schoox.com. A XXX.XXX.XXX.158 bigjaws.com. MX (10) mail.bigjaws.com bigjaws.com. SPF "v=spf1 +ip4:XXX.XXX.XXX.158 +mx ~all" From my understanding of SPF, the SPF status should have been passed: I designate that all email being sent by bigjaws.com from XXX.XXX.XXX.158 are valid/not spam (I added +mx there but I'm not sure if needed). When a mail server receives an email, doesn't it lookup the SPF record of the domain and checks against the IP it got the email from? Checking with spfquery: root@box:~# spfquery -ip XXX.XXX.XXX.158 -sender [email protected] -rcpt-to [email protected] StartError Context: Failed to query MAIL-FROM ErrorCode: (2) Could not find a valid SPF record Error: No DNS data for 'bigjaws.com'. EndError noneneutral Please see http://www.openspf.org/Why?id=employee1%40bigjaws.com&ip=XXX.XXX.XXX.158&receiver=spfquery : Reason: default spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com Received-SPF: neutral (spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com) client-ip=XXX.XXX.XXX.158; [email protected]; If I go to the address listed above (openspf.org) it tells me that the message should have been accepted(!): spfquery rejected a message that claimed an envelope sender address of [email protected]. spfquery received a message from static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) that claimed an envelope sender address of [email protected]. The domain bigjaws.com has authorized static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) to send mail on its behalf, so the message should have been accepted. It is impossible for us to say why it was rejected. What should I do? If the problem persists, contact the bigjaws.com postmaster. Also, here are some headers from an email sent by one of our [email protected] addresses to a gmail.com address (by the way, bigjaws.de listed in the "Received: from" field was the initial domain hosted on the dedicated server before adding the .com one -- both are still listed as separate subscriptions under Plesk). Delivered-To: [email protected] Received: by 10.14.177.70 with SMTP id c46csp289656eem; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) X-Received: by 10.14.102.66 with SMTP id c42mr306186eeg.47.1382515860386; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) Return-Path: <[email protected]> Received: from bigjaws.de (static.158.XXX.XXX.XXX.clients.your-server.de. [XXX.XXX.XXX.158]) by mx.google.com with ESMTPS id l4si19438578eew.161.2013.10.23.01.10.59 for <[email protected]> (version=TLSv1 cipher=RC4-SHA bits=128/128); Wed, 23 Oct 2013 01:10:59 -0700 (PDT) Received-SPF: neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=XXX.XXX.XXX.158; Authentication-Results: mx.google.com; spf=neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws; s=default; d=bigjaws.com; b=WwRAS0WKjp9lO17iMluYPXOHzqRcOueiQT4rPdvy3WFf0QzoXiy6rLfxU/Ra53jL1vlPbwlLNa5gjoJBi7ZwKfUcvs3s02hJI7b3ozl0fEgJtTPKoCfnwl4bLPbtXNFu; h=Received:Received:Message-ID:Date:From:User-Agent:MIME-Version:To:Subject:Content-Type:Content-Transfer-Encoding; Received: (qmail 22722 invoked from network); 23 Oct 2013 10:10:59 +0200 Received: from hostname.static.ISP.com (HELO ?192.168.1.60?) (YYY.YYY.ISP.IP) by static.158.XXX.XXX.XXX.clients.your-server.de. with ESMTPSA (DHE-RSA-AES256-SHA encrypted, authenticated); 23 Oct 2013 10:10:59 +0200 Message-ID: <[email protected]> Date: Wed, 23 Oct 2013 11:11:00 +0300 From: BigJaws Employee <[email protected]> User-Agent: Mozilla/5.0 (Windows NT 6.2; WOW64; rv:24.0) Gecko/20100101 Thunderbird/24.0.1 MIME-Version: 1.0 To: [email protected] Subject: test SPF Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit test SPF Any ideas why SPF is not working correctly? Also, are there any DNS settings that are not needed anymore and create a problem?

    Read the article

  • Eventlog entry for allowed connection in Windows Firewall

    - by Jaap
    I was seeing a lot of entries in the eventlog: The Windows Filtering Platform has permitted a connection. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 10.xxx.xxx.xxx Source Port: 80 Destination Address: 10.xxx.xxx.xxx Destination Port: 31773 Protocol: 6 Filter Information: Filter Run-Time ID: 67903 Layer Name: Receive/Accept Layer Run-Time ID: 44 We have a loadbalancer which checks every second to see if the application is still running (a health check). The logs contain large amounts of this kind of entries, which makes the Event Viewer slow and it's difficult to find the more interesting logs. How do I make sure these messages don't end up in the event logs?

    Read the article

< Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >