Search Results

Search found 15160 results on 607 pages for 'boot disk'.

Page 273/607 | < Previous Page | 269 270 271 272 273 274 275 276 277 278 279 280  | Next Page >

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• Ubuntu and Windows and Separate HDs, oh my!

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. Here's a pic of the error I get when I try to boot to Windows: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu. (Someone suggested just reinstalling windows from installation CD. Agree?)

  Read the article

• Ubuntu 12.04 partioning an external drive without lossing data

  - by Menelaos Perdikeas

  I have an Ubuntu 12.04 with an external 1.5T disk (just for data). It is /dev/sdc1 seen below: $ df -T Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/sda1 ext4 1451144932 27722584 1350794536 3% / udev devtmpfs 6199460 4 6199456 1% /dev tmpfs tmpfs 2482692 988 2481704 1% /run none tmpfs 5120 0 5120 0% /run/lock none tmpfs 6206724 284 6206440 1% /run/shm /dev/sdc1 fuseblk 1465135100 172507664 1292627436 12% /media/Elements The thing is I would like to implement this rsync-based backup strategy and I want to use my /dev/sdc1 external drive for that. Since the guide mentioned above recommends placing the backup directory in a separate partition I want to repartition the /dev/sdc1 external hard disk but retain existing data in a separate partition. E.g. split /dev/sdc1 into two partitions: (i) one to be used exclusively for the rsync-based backup and (ii) the other for the existing miscellaneous data. How should I go about partitioning with minimal risk to my existing data and what kind of filesystem do you recommend? I would prefer a console-based guide but unfortunately all the material I found on the web is oriented towards partitioning the main (bootable) disk and not an external fuseblk filesystem used only for passive data.

  Read the article

• grub refuses to install to raid array

  - by ronno

  I have a software raid 0 setup with dual booting Windows 7 and Ubuntu 12.04. The GRUB bootloader that is already on the hard drive seems to work fine. However, since the latest package update for grub, it refuses to install the new version to the hard disk. grub-install throws the following error: /usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map. Auto-detection of a filesystem of /dev/mapper/< raid name_RAID0p9 failed. Try with --recheck. If the problem persists please report this together with the output of "/usr/sbin/grub-probe --device-map="/boot/grub/device.map" --target=fs -v /boot/grub" to < [email protected] update-grub pops the same "/usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map." every alternate line. I don't understand what exactly is going on. I'm afraid to reinstall the grub package because it might mess up the boot, which currently works fine. Is it safe to just ignore this?

  Read the article

• how do I fix a wrong UUID in grub.cfg?

  - by mozerella

  I run Debian Wheezy alone on my PC and I recently copied the root partition to another with rsync as I found that worked well (I also know about dd and ddrescue but they leave unusable space on the new partition). I generated a new random UUID for the new partition with sudo tune2fs -U random /dev/hda9 and also updated fstab / and /home entries. Then as I know so little about GRUB I used a gui (GRUB Customizer) to probe for the new OS and add an entry to GRUB and the MBR -it makes an /etc/grub.d entry then updates GRUB. On startup, the GRUB list contains the new OS (on sda9) but it boots the first OS (which I copied from -sda5). /boot/grub/grub.cfg contains the new debian OS but it looks like this set root='(hd0,msdos9)' search --no-floppy --fs-uuid --set=root 64662470-0e58-4dfd-90ac-43227d773556 linux /boot/vmlinuz-3.2.0-2-amd64 root=UUID=cc3bca0d-aee4-4b9c-95c2-57212cc36d4d ro quiet initrd /boot/initrd.img-3.2.0-2-amd64 the 1st uuid is of sda9, but the 2nd uuid there is of sda5. I can change the 2nd uuid at startup (with E) and it boots sda9. So how can I get grub.cfg corrected so that the sda9 GRUB list entry boots from sda9 permanently?

  Read the article

• how can i move ext3 partition to the beginning of drive without losing data?

  - by Felipe Alvarez

  I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

  Read the article

• New PC: win7 install issues with 2x3TB in RAID1

  - by goober

  Background / Components Not sure what I've done wrong. Built one PC before successfully in a similar way but this one seems to be struggling. I have the following components: ASUS P8Z68-V/Pro Gen 3 (updated to latest firmware) 16GB (2x8GB) RAM corsair hx850 power supply 2x3TB drives on the intel z68 controller 1x128GB SSD on the Marvel controller sapphire 7950 The problem I set up my 3 TB disks in RAID1 controller appears to recognize them fine during boot as one 2.7TB raid1 volume windows setup sees two disks, both 746 GB, but will only let me install to one and appears to work fine. windows appears to install fine after installer reboots, I receive "windows failed to start" error referencing code 0xc000000e and "\Windows\system32\winload.exe every time I do an install, a new additional "win7" entry is added to the boot menu; all lead to this error. What I've tried: updated the BIOS to the latest firmware attempted to repair the install tried clearing / removing raid / re-raiding drives tried formatting the drives during install attempted to clear the menu Of entries (can't figure out how to do that) No matter how many times I destroy the raid array, format the disks, etc. the boot entries keep piling up. Any idea where I'm going wrong?

  Read the article

• Is there an objective way to measure slowness of PC/WINDOWS?

  - by ekms

  We've a lot of users that usually complain about that his PC is "slow". (we use win XP). We usually check startup programs, virus, fragmentation, disk health and common problems that causes slowness (Symantec AV drops disk to 1mb/s , or a seagate HD firmware error in certain models), but in those cases the slowness is pretty evident. In other hand, the most common is the user complaining about his pc but for us looks OK, even in 6 years old desktops. People sometimes even complains about his new quad core desktops speed!!! So, we are asking if there's a way to OBJECTIVELY check that a computer didn't dropped its performance, compared with similar ones o previous measures, specially for work use (I don't think that 3dmark benchmark o similar may help). The only thing that I found that was useful is HDTune, but it only check hard disk performance. Basically, what we want is something that enable us to say to our users "see? your PC is as slow as was three years ago! stop complaining! Is all in your head!"

  Read the article

• What should I encrypt in Debian during install?

  - by ianfuture

  I have seen various guides and recommendations on web about how best to do this but nothing that clearly explains the best way and why. So I understand there is a need for part of Debian during install to be un-encrypted on its own partition to allow it to boot. Most info I have seen is call this /boot and set the boot flag. Next I believe the best approach is to create another partition out of all the rest of the disk space, encrypt this, then on top of that create a LVM and then within the LVM create my various partitions , name them , select size, and file system type. Can I include /swap in the encrypted LVM part ? Is this approach sound? If so what are the partitions I should use (this is going to be a minimal server install with a view to install as and when what I need for a dev server)? Finally how does the installer know what to put in each partition I define ? I appreciate there are more than one question but any help and suggestions would be appreciated. If further clarification is needed please mention in the comments . Thanks.. Ian

  Read the article

• Spotlight has stopped indexing/returning anything in /Applications

  - by pra

  After a recent kernel panic & restart, Spotlight no longer seems to know anything about the files under my /Applications folder. I used to launch Safari.app, Opera.app, Textedit.app, etc via Spotlight as a matter of routine. Now, I get "No results found" for all of them (except Textedit.app, which launches a demo text editor from a Qt installation). The programs are still there & still launch directly from Finder. I've already run disk utility & verified the disk, no issues. I repaired disk permissions, which made several changes, but to no effect. Is there anything else I can do, short of re-installing MacOS? Update: I already verified that "Applications" was still checked in my Spotlight preferences. It was still returning applications located elsewhere (the Qt textedit sample app), so that shouldn't have been the issue. A few hours later it resolved itself; I guess there's a background process running on some interval.

  Read the article

• Windows 8 preinstall downgrade to Win 7: UEFI problems :/

  - by Tim Flemming

  I have a friend who has a Hp Laptop with UEFI booting. He locked himself out of windows 8 (forgot his password)... so he called me. Well after trying to use the latest version of chntpw in UBCD5.2.6, i came to the conclusion i needed to wipe the drive and install windows 7. A little googling suggested using certain versions of chntpw, but i decided to not waste the time burning endless CDs. Anyway, He agreed to installing Win7 "I hate the big tile thingys". So i attacked with Gparted. Wiped the whole drive. Set flags to boot. Set part table as MBR. However upon trying to install win7, it still claimed i had a GPT style disk. unable to install. the only thing i can think of I'm doing wrong is not changing the bios/UEFI to legacy... My question is, If I enable legacy, somehow get the drive to actually be MBR, and use my X86 DVD, should I be good? Is there some common glitches ppl miss when dealing with GPT/EFI/UEFI? I need answers cuz he now has a blank laptop which I am responsible for. Another question. windows 8 came installed on a GPT disk. SO WHY WHEN I BOOT THE INSTALL DVD DOES IT SAY IT CANT INSTALL TO A GPT STYLE DISK??? WTF??? talk about the bleeding edge man.

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• Backing up a Windos 7 partition from Macbook with no OS X

  - by mattcodes

  I have a 3 year macbook with Windows 7 installed as 40gb and OS X as 40gb (80gb HD). I want to remove OS X as Im at the limit of 40gb on Windows and I have not logged on to Mac OS X since installed Win7 (dont flame me). So I want to delete OS X partition and expand my win partition to 80gb BUT I still would like to be able to regularly (once a week/month) backup my Windows 7 partition - its took a while to setup everything up right - not just docs and programs - so when the hard drive dies I want to be able to restore the partition and boot away, (the daily volatile bits I can pull down from dropbox and project from soure control). With Mac OS X I could use Winclone - and this worked flawless last time the HD failed with XP but with the absence of OS X I will need something else. Im thinking can I use a Linux Live boot CD along with an external USB hard drive. Boot from CD and then dd? the partition to the USB? What linux distro live CD should I use? I say dd as if I know what am taking about (I dont) is this the best way to backup a partition (when it will be restored to same hardware as bootable) ? What command?

  Read the article

• Computer loop restarts on Windows loading

  - by Robinson G.

  My computer restarts, just after or during Windows loading (4 squares getting together), or after some time on the desktop IF I'm idle. In order to start the computer I either have to swap my RAM (24Go) in differents DIMM slots, for example (I have 4 slots) : 1-2-4 or 2-3-4 or 1-3-4, not the same position each boot or it restarts in a loop... I can also change the ram timing from 1.5 to 1.6V and it starts, at the next reboot I have to change it again to 1.5 or it won't boot... And If after all, I succeed to boot, I have to use the computer for about 10 minutes, and it's ok, if I don't, it restarts by itself after some minutes. If I stay on the BIOS, It's all OK, I can stay for a whole year without restarting. I have check my RAM on Memtest (4*8G SDRAM DDR3) : OK I have check without graphic card : Still the same. I tried to reset the bios stack by getting it off and on : Still the same. I tried to reset my BIOS, and many settings about the RAM in the menu : Still the same. CPU temps are just fine (around 35°C) I was thinking ofc about the motherboard but I want to be sure. Motherboard : MSI zh77a-g43 RAM : 4*8G Dual Mode or not (depends on the number I put ofc.) PSU : 600W (enough to run all the config) CPU : i7 3770 non K

  Read the article

• In Windows 7 power management, is it possible to set different sleep settings for different SATA disks?

  - by Ben Voigt

  I'm having an issue with Windows 7 either freezing up or generating a BSOD coming out of sleep. I suspect that it is related to my boot/OS drive, an OCZ Vertex SE SSD, because numerous other Vertex users have reported sleep problems. Notably, if I put the computer to sleep, it almost always wakes correctly. If it goes to sleep after a timeout, it almost always BSODs. I disabled timed sleep and now it freezes when left unattended. My next step is to disable "Put hard disks to sleep after X minutes", but I'd like to change this setting only for the SSD and not for the rotating data disks, which I would like to spin down normally. Does anyone know a place to configure sleep on a per-disk basis? I don't need to set different timeouts on different disks (although that would be nice), simply setting "this disk sleeps" and "sleep is disabled for this disk" would be great. Additional system information: Windows 7 Ultimate x64, Core i5 - P55 chipset, Intel RST drivers are installed. One SSD, two rotating HDD, and a DVD-RW drive are all connected to the Intel SATA ports. I could potentially move some of these to my motherboard's other SATA controller if that would help.

  Read the article

• How do I cancel windows server 2003 repair install?

  - by Kilgore2k

  System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

  Read the article

• Data recovery from corrupt Ubuntu partition/directory (question about a previous answer)

  - by JoshMaurice

  I have an Ubuntu installation that won't boot anymore. I asked my previous question about it here: http://superuser.com/questions/15916/ubuntu-chkdsk-equivalent Bolotov replied: As I see from your previous question you can boot Windows so you could use dskprobe from Windows XP Service Pack 2 Support Tools to make sure that fs type is correct ... but it's already correct fs type 7 is NTFS. Message "The type of the filesystem is RAW. CHKDSK is not available for RAW drives." means that windows can't determine fs type for some reason. As we see fs type is correct. To run Chkdsk on your Windows partition you can install Windows Recovery Console, boot in recovery console and check your disk. After checking the disk you will gain access to you c:\ubuntu\disks. I think you can mount your linux partition (which is in file) as usual loop-back device: mount -o loop [path to your linux-loopback-partition] But you should mount windows patrition first. So now I'd like to know: Within the recovery console I will be issuing the commands "chkdsk -r" and then "mount -o loop [path to windows partition]" and then "mount -o loop c:\ubuntu\disks", correct? I do have a ("corrupt and unreadable") c:\ubuntu\disks directory so that appears to be the correct path to the linux partition; do you know the path to the windows partition? would that be just "c:\"?

  Read the article

• Is it safe to force a dismount to format a volume in Windows?

  - by sammyg

  I am using format command in cmd to format a USB flash drive. M:\>format /FS:FAT32 /Q Required parameter missing - M:\>format M: /FS:FAT32 /Q Insert new disk for drive M: and press ENTER when ready... The type of the file system is FAT32. QuickFormatting 14999M Format cannot run because the volume is in use by another process. Format may run if this volume is dismounted first. ALL OPENED HANDLES TO THIS VOLUME WOULD THEN BE INVALID. Would you like to force a dismount on this volume? (Y/N) y Volume dismounted. All opened handles to this volume are now invalid. Initializing the File Allocation Table (FAT)... Volume label (11 characters, ENTER for none)? Format complete. 14,6 GB total disk space. 14,6 GB are available. 8 192 bytes in each allocation unit. 1 917 823 allocation units available on disk. 32 bits in each FAT entry. Volume Serial Number is E00B-2739 M:\> Is it safe to force a dismount like this, and make the handles invalid?

  Read the article

• Half of installed RAM is hardware reserved

  - by user968270

  After a rather arduous and convoluted series of problems that left me without a desktop for ~80 days, I've finally got the thing up and running, having replaced the power supply, motherboard, graphics card and CPU. Now, however, I'm experiencing the 'hardware reserved RAM' issue. Perhaps this is the exhaustion talking, but looking at the question that tends to get pointed to when this kind of topic gets locked as a duplicate hasn't helped. I have 16 GB of RAM installed in an MSi 970A-G46, which is spec'd for up to 32 GB of RAM. The BIOS recognizes that I have 16 GB installed, and the resource monitor also shows the whole 16 GB, only it shows 8 GB as hardware reserved. I've seen suggestions that it's an OS issue, but the particular installation of Windows 7 (64-bit) which I'm running on my boot drive is the same as the one that could actually access the 16 GB in my previous motherboard (MSi 870A-G54). I've updated my BIOS using the MSi Live Update tool and restarted the machine with no effect, and I cannot seem to locate any 'Memory Remapping' option as I've seen mentioned. I've physically swapped the RAM between the slots to no effect. I've unchecked the Maximum Memory box in the msconfig Boot tab's advanced options, also to no effect. These are my system's basic specifications OS: Windows 7 Home Premium (64-Bit) Motherboard: MSi 970A-G46 CPU: AMD FX-8150 Graphics Card: XFX Radeon HD 6870 Boot Drive: OCZ Agility 3 Storage Drive: Samsung Spinpoint F3 ST1000DM005/HD103SJ 1TB PSU: Thermaltake TR-2 TR600 600W ATX12V v2.3

  Read the article

• Hyper-V and attaching physical disks

  - by Mike Christiansen

  So, I'm looking at rebuilding my home server. My current setup is the following Windows 7 Ultimate 1TB Boot Drive (my smallest drive) Windows Dynamic Spanned volume, continaing 1x 1TB drive, 2x 2TB drives, totalling 5TB. I am upgrading to a hardware RAID controller, and I would like to run Hyper-V server core. However, I want to retain the ability to join my "file server" to a homegroup, so I must use Windows 7. I know VHDs can only be like 127GB or something, so I obviously need to directly connect disks to my Windows 7 machine. Here is my plan: Server Core 2008 R2 (Hyper-V) 1TB Boot Drive (storing VHDs for boot drives of VMs) - possibly in a RAID 1 with my other 1TB drive 5x 2TB drives (1x 2TB drive hot spare), totalling 10TB, directly attached to a Windows 7 VM, for use of homegroup for this array. In the past, I directly attached the windows dynamic volume to a Windows 7 VM, and performance was abysmal. The question is, with hardware RAID, will it really make that much of a difference? Server specs: Intel Core 2 Quad Q9550 2.83GHz Asus Maximus II Formula (PCI-E x16) 8GB DDR2 RAM PC2-6400 (Yes, I know its a bit out of date)

  Read the article

• Rescue system running TFS that BSODs, into vmware esxi

  - by 3molo

  Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

  Read the article

• What should I encrypt in Debian during install?

  - by ianfuture

  I have seen various guides and recommendations on web about how best to do this but nothing that clearly explains the best way and why. So I understand there is a need for part of Debian during install to be un-encrypted on its own partition to allow it to boot. Most info I have seen is call this /boot and set the boot flag. Next I believe the best approach is to create another partition out of all the rest of the disk space, encrypt this, then on top of that create a LVM and then within the LVM create my various partitions , name them , select size, and file system type. Can I include /swap in the encrypted LVM part ? Is this approach sound? If so what are the partitions I should use (this is going to be a minimal server install with a view to install as and when what I need for a dev server)? Finally how does the installer know what to put in each partition I define ? I appreciate there are more than one question but any help and suggestions would be appreciated. If further clarification is needed please mention in the comments . EDIT : 16/3/2010 After Richard Holloways reply I thought it relevant to add this info: The reasons why I want to do this are to explore maximising security on any server install and set up, due to interest in the area of Computer Security and Forensics. Also I am trying to peform the task as if it being performed in an enterprise situation. On a technical matter, once set up and configured with minimal packages and ssh this server will not physically be easy to access so I will only be entering via ssh. (Yes I know why encrypt something no one will ever be able to get their hands on? Because I can and I want to is the simple answer, but see above too).

  Read the article

• Windows Server doesn't connect to a network share

  - by Dmitriy N. Laykom

  Windows Server doesn't connect to a network share. Network share is working. Blockquote Pinging 109.123.146.223 with 32 bytes of data: Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Ping statistics for 109.123.146.223: Packets: Sent = 3, Received = 3, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms net view \shareaddress Blockquote System error 53 has occurred. The network path was not found. When I connected the network share I observed this error message: Blockquote \ "Mapped disk letter" refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure that the disk is properly inserted, or that you are connected to the Internet or your network, and then try again. If it still cannot be located, the information might have been moved to a different location The network share was mounted via Group Policy. Perchance anyone knows how I can avoid this error? When the OS has been restored from the disk problem has been solved

  Read the article

• Suspected Corrupted Windows 7 MBR?

  - by AridDecay

  So, this may not be the correct place to put up my question, but i'll give it a shot. I'm having an issue repairing this computer. It was brought to me with the described issue of 'Not turning on' Later, I found that it would come with the error of 'No boot sector found on internal hard drive.' I assumed it was an MBR issue due to a virus or cutting a Windows update short. I booted into my trusty recovery enviroment and ran bootrec.exe /FIXMBR and restarted -- No luck I started to think (After multiple attempts to get the MBR sorted out, including creating a new boot sector) that the Hard-drive was possibly starting to cave in on itself, so I booted into a linux bootable CD and went to check the SMART data. Odd, say's it's inaccessible. That seems odd to me, considering it's a newer (two years old or so) Windows 7 computer. All new Hard-drives have SMART. So, I checked the BIOS. No mention of SMART anywhere. Greaaaat. I decided as a last-ditch effort to switch the hard-drive type to ATA in the BIOS (God knows why, I was getting frusterated) instead of AHCI. VOILA! It actually attempts to boot, gets halfway through the little windows animation, does an incredibly (Half a second) quick BSOD, and shuts down. Does anyone have ideas on what's going on here? I'm at my wits end.

  Read the article

• Why is my rsync so slow?

  - by iblue

  My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

  Read the article

< Previous Page | 269 270 271 272 273 274 275 276 277 278 279 280  | Next Page >