Search Results

Search found 13909 results on 557 pages for 'old man'.

Page 275/557 | < Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >

• Raid HDD Boot up

  - by user234695

  My server is Power Edge 1950 running server 2008 32Bit, using 3 Physical SAS HDD as a Virtual 2 Disk configured for RAID5, with partition of C drive as OS and D drive as Data. Planning to format and install Server 2008 R2 64Bit so I insert a New Physical disk and configured as RAID5 and clone the C drive and D drive to the new hard disk. Now I need to test that the new hard disk is able to boot windows and work as expected. How do I test, I am not able to boot the windows by choosing the new harddisk, the bios show only the existing HDD, not the new one. Also, if I remove the old three hard disk, and leave the new harddisk and then am I able to boot the device, if I do this does my existing RAID5 configuration and data on the hard disk still remain.

  Read the article

• unable to install new versions of linux on my PC

  - by iamrohitbanga

  I have an MSI-RC410 motherboard with onboard ATI Radeon XPress 200 series Graphics card. I have used OpenSuse-11.0 on my PC for over an year. but when I tried to upgrade to OpenSuse-11.1, I managed to install it only to find that several features were missing. for example /dev/cdrom was missing. Also install DVD of Fedora 11 did not work. I have also tried Ubuntu-9.10 live cd. When I boot from the CD i get the initramfs command prompt. Still able to install old versions of these OSs. What is the reason for this behavior? Does it have to do anything with the new version of the linux kernel not being compatible with my hardware? What should i do to install new versions of Linux?

  Read the article

• Making a Live Thumb drive boot with Persistent files, settings AND *drivers* that load on boot?

  - by Luke Stanley

  I have seen https://wiki.ubuntu.com/LiveUsbPendrivePersistent but it's a mess. What methods support persistent drivers as well as files and settings and don't screw up lifespan of the flash drive? I'd like to see your personal recommendations on say, Portable Linux, USB Creator, Remastersys + Unetbootin, etc Backstory: I have a Inspiron 1525 that's hard drive has been slowly dying. I want to switch to a live USB/CD/DVD system until I can get it repaired but my laptops internal wifi device requires a network connection by another means for Xubuntu to let it work, and then I have to enter my Wifi key again, and THEN I have to reinstall Skype etc... I'd be damned every time I have to shut the laptop down. I'm ok with making a shell script for installing apps and copying settings as required but a good persistent install should make this old hat and slow and it doesn't take care of drivers. The last time I tried making an ISO with Remastersys it didn't seem to copy all the required settings.

  Read the article

• Which is better for running Ubuntu and other Linux OSes, Chromebook or Windows, why? [on hold]

  - by Serge

  I'm learning programming and I would like to switch to a Linux OS, perhaps Ubuntu, to continue this, but the current machine is generally getting pretty old and slow and Windows is the least favorite option for production, and I can manage getting something new right around the price range of the nicest Chromebook on the market right now. However, I have compared specs of HP Chromebook 14 with those of regular PC laptops that roughly cost the same, and the latter consistently have approximately the same and sometimes higher (like the processor speed) specs. Yet usage of Chromebooks for this purpose is pretty widespread nowadays. Is this because they were initially built for a Linux OS - and is it really THAT crucial - or are there other major factors at play here?

  Read the article

• Why is my firewall preventing me from accessing some websites

  - by nosx

  I have an old Belkin router and when I enable the firewall I cannot access certain websites. For example: http://www.avisynth.org With Firewall Enabled: Main page loads and begins to do a meta refresh which never finishes. With Firewall Disabled: Main page loads and the meta refresh completes as normal and I am taken to the wiki page. I have not setup any rules in my firewall that would prevent this site from loading, yet it refuses to load unless I have the firewall disabled completely. My router has a hidden page with advanced settings on it for the firewall which I was able to acccess and take a screenshot of, but I did not want to mess with these values unless I absolutely have to do so: What might be causing this problem and how would I go about fixing it?

  Read the article

• Digital Blue Digital Movie Creator 3.0 driver

  - by user27977

  I'm having a complete 'mare of a time trying to use my schools Digital Blue cameras. We've got the model 3 ones, but can't find the driver disc and using the Windows Hardware Installation Wizard gets me no where! Can you help me to find the driver? When I've used it at my old school it had a piece of software called the Digital Movie Creator, which I've heard you can use to make stop-motion films, which is what I want to do! This is what it looks like http://www.amazon.co.uk/Digital-Movie-Creator-1GB-Card/dp/B000LP30LA/ref=sr_1_2?ie=UTF8&s=software&qid=1265928833&sr=1-2

  Read the article

• trying to set and use a password via commandline using ultraVNC on windows server 2003 vnc

  - by mustafa

  Okay, so I installed ultravnc on windows server 2003. It uses the ultravnc.i.i file to store password and configuration information. But I'd like to be able to set the password using the command line. There is a tool called vncpwd: http://www.sysworksoft.net/products/vncpwd.html But it's old, and when you use it to change the password, it changes the password in the system registry instead of the ultravnc.ini file. But, you can set ultravnc to use the registry instead of the ini file. Success? No. I set ultravnc to use the registry (which stores the hashed password that I set using vncpwd), but, it still uses the password in the .ini file. does anyone know what gives.

  Read the article

• Linux Kernel IRQ Routing with irqbalance / kernel options

  - by tim

  I'm trying to get my Xen Dom0 distributing the irqs in an smp enviroment. As far as I know there are 2 Options: Use irqbalance Configure the kernel without cpu hotplug support My System is Debian Squeeze, Xen 4.0.4, Kernel 3.2.31. My Problem is: irqbalance segfaults due to a changed /proc/irq* layout or irq0 missing (this seems to be a very old bug existing since Lenny) To configure a kernel without cpu hotplug support you must disable cpu powermanagement which seems to be impossible through the standard wys (make config / make menuconfig) - the option CONFIG_PM simply defaults to "Y". Any idea anyone on how to get a debian dom0 kernel with a proper irq distribution?

  Read the article

• How do I disable Tomcat? [closed]

  - by Dave King Popeye Mason

  Possible Duplicate: How to disable Tomcat on linux? According to my server host, something called Tomcat is hogging all my resources and slowing down the server. As far as I'm aware I'm not using it as the only thing running on the server is Plesk and a few Wordpress installations. I'm a real dummy at using SSH, I can navigate to folders, change permissions and that's about it. Could somebody explain to me as if I'm a 5 year old how to disable TomCat (and also how to stop it re-enabling on startup)? Thanks!

  Read the article

• Disable DirectDraw, but still have Direct3D?

  - by GodsBoss

  I have a Windows XP SP3 machine, with up-to-date patches. It has DirectX 9.0c, version number 4.09.00.0904. Can I disable DirectDraw, but have Direct3D still active? I read the Wikipedia articles about DirectDraw and Direct3D, but do not know if I understand them correctly: That is, it contains many commands for 3D rendering; however, since version 8, Direct3D has superseded the old DirectDraw framework and also taken responsibility for the rendering of 2D graphics. Does that mean DirectDraw is now a part of Direct3D? Because I cannot disable DirectDraw without disabling Direct3D, but it works the other way around.

  Read the article

• Creating Shared Wifi Connection on Windows 7 WITHOUT wep/wpa security?

  - by Duncan

  Ok, for some reason I just can't figure this out on Windows 7. Never had an issue with it on Windows XP, never tried in Vista. I realize that I need to create an Ad-Hoc setup which I can do. However I can't get it to share the wireless signal on my laptop. Even if I go into the adapter settings. I need (well, want) to connect my old Psion netBook to my home network and due to the wireless card, I can't have any form of security. Thanks in advance!

  Read the article

• Hypervisor for mixed client and server OSes

  - by Mark

  I need to replace three old boxes I use for development, running Linux, Win Server and Win XP. Instead of purchasing three new boxes I am thinking of purchasing a single box and virtualizing the OSes. As it is for development, absolute performance is not a problem, but I want the Linux and Win servers to run continuously, while running Win 7 as if it is a regular PC. Therefore running Linux and Win Server on top off Win 7 is not an option. Is this a viable solution? Has anyone done this? What is performance like? I'd like to get decent graphics performance with Win 7, sufficient to run the occasional game. If so, I'm looking for suggestions or recommendations on which hypervisor or virtualization option to go for.

  Read the article

• Cancel table design change in SQL Server 2000

  - by Bryce Wagner

  In SQL Server Enterprise Manager and change one of the columns and save it, it will create a table with the new definition, and copy all the data to that new table, and then delete the old table when it's done. But if your table is large (let's say on the order of 100GB), it can take a long time to do this. Even worse, if you don't have sufficient disk space, it doesn't notice ahead of time, and it will spend a long time trying to copy the table, run out of space, and then decide to abort the process. We have other ways to copy the data in smaller chunks, but those require significantly more manual intervention, so it's usually easier to just let Enterprise Manager figure it out, as long as there's enough disk space. So for a long running "Design Table" save like this, is there any way to cancel once it's started? Or do you just have to wait for it to fail?

  Read the article

• ATI radeon hd 5450 Graphics Card Issues

  - by RGM-79FP GM Striker

  I have an Old Dell Optiplex 755 SFF with an Intel Core 2 Processor (windows 7). Now This can hold a PCI-E x16 port. Now I got an ATI Radeon HD 5450 low profile. I plugged and played and it fits without a hitch, the software installed too! , now for the graphics well... It doesn't really work at all as it seems to freeze at the moment that it loads on the windows logo. It loads into safe mode so I'm not really sure what the problem is. Any ideas, I read the dell forums and they should be somewhat compatible... with the specs so I'm at a loss here. and I am a novice here. Ideas? Edit I have tried to reset the cmos,no luck there. I have tried to move the ram as well. nothing big happened.

  Read the article

• How to reset mac PRAM through the command line in Lion/Mountain Lion?

  - by boneyjellyfish

  I'm trying to write a script to automate a PRAM reset and I've seen a lot of old guides that tell me to use the following command to reset the Mac's PRAM via the terminal: nvram boot-args="-p -r" But this command doesn't seem to work anymore, at least not on any of the computers I've tried it on. I'm trying to find a more up-to-date list of available boot-args and I was able to find this question about boot-args strings but there doesn't seem to be anything in there or any of the links about resetting the pram. Any ideas?

  Read the article

• Mac OSX server command equivalent for dhclient?

  - by John Hall

  Is there an MacOS command that makes a dhcp request, and renews the old lease, drops it for a new one, or usefully reports errors or lack of response from a dhcp server? This would both help fix networking on the machine after problems on the network without rebooting and would also be useful to diagnose wider networking problems from a mac. I can not find any command equivalent of dhclient though obviously some component must be serving this purpose. The question is, is that component exposed to a command line interface? I am biased to the command line for these features and may have overlooked settings panels or tools that might solve it using a gui interface. I believe this question is at the heart of this other question: Is there an equivalent command for 'init.d/networking restart' in OS X

  Read the article

• Digital audio input on Macbook?

  - by Ken

  I have: a Macbook (not Pro), don't know the exact model but it's a Core 2 Duo 2.0GHz and probably what Wikipedia calls the "Late 2006" or "Mid 2007" model a DVD player, region-free, that has "Coax and TosLink optical digital audio outputs" I want to make an MP3 of the audio track of some DVDs (for learning a new language), and I can't use the Macbook's built-in DVD drive because it's a different region (ugh!). I'm sure I can connect the DVD player to the Macbook with an analog audio cable. However, if it's possible I'd prefer to keep the signal digital. I'm not even positive if my old Macbook has digital audio in, and if so what I need to connect to it. (I've done plenty of home audio geeking, but always in analog!) Will a "Toslink cable" plus a "Toslink Female to Mini-Plug Male Adapter" (found on Amazon) let me connect my things together? It looks like the pieces will fit but I'd like to hear someone confidently knowledgeable on the matter before I buy something. Thanks!

  Read the article

• How does fail2ban 0.9 database storage actually works?

  - by Arantir

  Fail2ban 0.9 introduce database storage to save bans on restart. But I can't find out the actual mechanism of it work. There is dbpurgeage parameter which controls lifetime of old bans, defaults to 24 hours. As I see from code research, fail2ban saves a ban to the db with timeofban equals to the moment of ban being saved. Then every dbpurgeage period it removes all bans with timeofban < MyTime.time() - self._purgeAge, in other words removes all bans have been stored more than 24 hours ago. But what if an IP was banned for the month? Does all this mean that with dbpurgeage = 86400 after restart in 24 hours I will lost all bans longer than 24 hours? I just want that all my permanent bans will be preserved in any case.

  Read the article

• Does a Required Restart for Windows Update log an event? If so what is the source/id?

  - by Beuy

  Hi there, Does anyone happen to know if a required restart in order to apply Windows Updates creates a entry in the event log? If so which log is it under, and what is the source/id? I have a legacy system that needs to an account, constantly logged into console for applications to function as required (Some old PROCOMS modem software for customers without Internet access but a telephone (Dial-up? Separate issue, don't get me started -.-)). When an update is applied to this machine that requires a restart (Server 2003) I would like an e-mail alert to be sent.

  Read the article

• Wireless card not found on Ubuntu

  - by Idealflip

  Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

  Read the article

• FTP an entire folder via the command line

  - by Chris Southam

  I'm looking so migrate some websites to a new server. I have SSH access to the current one but only FTP access to the new one. How can I via Centos and SSH copy entire folders to the new server via FTP? I can log into the new server via the built in FTP client on Centos but I'm not sure of the commands after this. I need to move the httpdocs folder from the old to the public_html folder of the new server. I'd love to do this server to server as it'll be a lot quicker than download - upload via my broadband connection. Yours, Chris

  Read the article

• Program to read and convert entire website to html

  - by Frederik Wordenskjold

  I'm using a very old cms, Synkron.web. I need to convert all of my pages (written in .asp) to plain html - so I have an archive where all of the pages from my website are saved. I was wondering if there isnt some kind of program out there, with the ability to traverse all documents on a website, view their source, and save them as html-pages on my local machine? If not, do you have any suggestions on how to convert a Synkron.web database, to some kind of open-source CMS? Like Wordpress, etc...

  Read the article

• Thin virtual host

  - by Adam Ryczkowski

  My work setup relies on old Windows XP. Now, when Windows XP isn't supported by new hardware, it's getting harder and harder to buy a notebook on which Windows XP can run natively with all essential hardware (wireless cards, graphics, sound etc). Since I don't expect my personal setup to turn away from Windows XP any time soon, I'm investigating the following trick: why not buy any decent hardware which Linux can fully utilize, and use it as a virtual host for a guest session with e.g. Windows XP. I like using hibernation, so I prefer this Linux to be as thin as possible, only enough to support VirtualBox, KVM or any other virtualization software. Question: Are there any "standard" ways to do this, like Linux distributions aimed specifically on being light virtualization host?

  Read the article

• How to gain admin privileges on D-Link router if my isp is not allowing me to do so?

  - by Fischer

  So I switched to new ISP yesterday, they gave me a D-Link router, can't use my old router. I want to change the wireless password, went to 192.168.1.1, I can login with the the username and password user user, but not as admin. On the catalog it says that the default username and password are admin admin, tried that didn't work. Tried admin and no pass, tried many combinations, none worked. I asked some other users and they said that the isp is blocking the users from logging in as admins, and blocking the reset button, and said that there's a hack where you do something like: cmd telnet "router ip" and do something like dumpcfg. Could you please give a better explanation on how to gain admin privileges on your own router if your isp is not letting you do so by default?

  Read the article

• OpenVPN Push DNS Not Working Correctly On Windows

  - by woodsbw

  I currently have OpenVPN server setup on an Ubuntu machine, as well as DNSMasq. I am wanting to push DNS to the client (road warrior setup.) I had the push "dhcp-option DNS x.x.x.x" where x.x.x.x was an open OpenDNS server, for testing, and everything was working when I connected from my Windows client But now that I have DNSMasq setup, and I changed the "dhcp-option DNS x.x.x.x" to the DNSMasq server, but when they client connects it still receives the old, OpenDNS DNS server IP. I'm at a bit of a loss here, I have tried flushing DNS on the client, rebooting the server, and I even grep'd the entire server to see if the OpenDNS IP was in some other config I was missing...it wasn't. One other note, when connect to the VPN and explicitly run nslookup against against the DNSMasq IP, the addresses resolve correctly, so it isn't a DNSMasq issue.

  Read the article

< Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >