Search Results

Search found 18927 results on 758 pages for 'remote desktop'.

Page 280/758 | < Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >

• VPN only connects to its server!

  - by Eddie

  Hi guys; Previously I bought a windows 2003 VPS and enabled routing and remote access so that users can make a vpn connection. I turend the firewall off and everything was working fine. But since 2 days ago whenever I try and connect to vpn it connects to vpn without any problem and I can see the connection status however it only connects to the server I mean what I can do with this vpn is to connect to the server via remote desktop and I can ping only the server's IP, neither I can open any webpages in browsers or ping other IP addresses beside the server one! I've also rebuilt the server and configured it for routing access and vpn connection from the beginning but it doesn't work either. It seems that server fails to route the traffic properly, as i'm sure that the firewall has been turned off I can't figure out what's the reason, any idea what's going on? Thanks in advance

  Read the article

• Forward all traffic through an ssh tunnel

  - by Eamorr

  I hope someone can follow this and I'll explain as best I can. I'm trying to forward all traffic from port 6999 on x.x.x.224, through an ssh tunnel, and onto port 7000 on x.x.x.218. Here is some ASCII art: |browser|-----|Squid on x.x.x.224|------|ssh tunnel|------<satellite link>-----|Squid on x.x.x.218|-----|www| 3128 6999 7000 80 When I remove the ssh tunnel, everything works fine. The idea is to turn off encryption on the ssh tunnel (to save bandwidth) and turn on maximum compression (to save more bandwidth). This is because it's a satellite link. Here's the ssh tunnel I've been using: ssh -C -f -C -o CompressionLevel=9 -o Cipher=none [email protected] -L 7000:172.16.1.224:6999 -N The trouble is, I don't know how to get data from Squid on x.x.x.224 into the ssh tunnel? Am I going about this the wrong way? Should I create an ssh tunnel on x.x.x.218? I use iptables to stop squid on x.x.x.224 from reading port 80, but to feed from port 6999 instead (i.e. via the ssh tunnel). Do I need another iptables rule? Any comments greatly appreciated. Many thanks in advance, Regarding Eduardo Ivanec's question, here is a netstat -i any port 7000 -nn dump from x.x.x.218: 14:42:15.386462 IP 172.16.1.224.40006 > 172.16.1.218.7000: Flags [S], seq 2804513708, win 14600, options [mss 1460,sackOK,TS val 86702647 ecr 0,nop,wscale 4], length 0 14:42:15.386690 IP 172.16.1.218.7000 > 172.16.1.224.40006: Flags [R.], seq 0, ack 2804513709, win 0, length 0 Update 2: When I run the second command, I get the following error in my browser: ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://109.123.109.205/index.php Zero Sized Reply Squid did not receive any data for this request. Your cache administrator is webmaster. Generated Fri, 01 Jul 2011 16:06:06 GMT by remote-site (squid/2.7.STABLE9) remote-site is 172.16.1.224 When I do a tcpdump -i any port 7000 -nn I get the following: root@remote-site:~# tcpdump -i any port 7000 -nn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on any, link-type LINUX_SLL (Linux cooked), capture size 65535 bytes channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused channel 2: open failed: connect failed: Connection refused

  Read the article

• MTU, DSL router and stalling TCP

  - by user38843

  I am discovering stalling TCP connection problem. The problem arises when I try to scp stuff from remote system from my home network. My home network is connected to internet via PPPoE (ADSL+) and everything works perfectly once working from my home network. The ADSL router has MTU set to 1492 but with that setting the scp from remote system does not work - stalling! When I change the MTU on my router to 1500 the that scp works perfectly but internet accesses from my home network is very slow to most of the www sites - even local ones. Just wondering where the problem exists - my ISP blocking ICMP, etc? Thanks!

  Read the article

• Finding the model of an old computer i used to own?

  - by mcbeav

  This might sounds ridiculous, but I need some help finding the model of an old computer i used to own. I know what the computer looks like. It was made by Packard Bell, but i can't find hardly any information on older packard bell computers anywhere online. I got the computer around 1999, give or take a couple of years. It came with Windows 98 preinstalled. It was a tower desktop. I was wondering if anyone knows of a website or reference tool where i can find some information on older model desktop computers.

  Read the article

• Mac OS X: network disabled because security breach

  - by fireeyedboy

  Dear all, I just recieved a message on my Mac OS X system telling me (loosely translated from Dutch): "The network has been temporarily disabled because the network's security was breached." (It's a wireless WPA2-PSK secured network BTW) I looked in the logs of my router (a Zyxel P-2602HW-D1A) only to see a few (outbound) "syn flood TCP ATTACK" logs, but those were from like a week ago, other than that nothing. What tools on Mac OS X do I have to analyse this security breach occurence? Are there some security logs on Mac OS X that I can inspect? What other measurements should I take? And how serious should I take this warning from Mac OS X? System: Macbook Pro Intel Core 2 Duo 2.2 Ghz OS: Mac OS X 10.5.8 Network: wireless WPA2-PSK Relevant software: Parallels Desktop with Windows XP (was open, but stopped at the time) Other systems on my network: Windows XP SP3 desktop (was running at the time) If you need any more info, don't hestitate to ask. Thanks in advance.

  Read the article

• VPN Split Tunneling - Pros and Cons and how to achieve?

  - by Theveloper

  Well this is the dilemma, I want remote clients to connect to my network and only route local access through the VPN. This is split tunneling, the client uses its internet connection for all other internet requests and the VPN tunnel to my network for local requests. There's a couple of issues that arise: split tunneling in Windows is achieved by unticking an option which reads "Use default gateway on remote network" in the TCP/IP settings of the client VPN connection. At any point the user can tick it and route all his internet traffic through my network eating away at my bandwidth and being cloaked by my IP address. This is unacceptable. Issue number 2 is that if the client is split tunneling, he becomes a gateway between the internet and my network, this is also unacceptable. My questions are: how does one achieve split tunneling serverside? And is the latter issue a valid con worthy of worry? Any thoughts would be appreciated!

  Read the article

• Can't connect to Windows Server 2008 shared folders via VPN connection

  - by Pearl

  I set up an VPN connection on my 2008 server using RRAS. The VPN seems to work fine. I can connect from outside the network. I am also able to establish a remote access connection via the VPN-IP. However, I can't access my shared folders. After connecting to the VPN I can ping the server, but it is not shown in my networks. using \ip or \server-name doesn't work either, cannot be found. I checked ipconfig and this is what I found regarding the VPN: DNS-Suffix: Description: test Physical Adress: DHCP activated: No Auto-Config: Yes IPv4-Adress: 192.168.2.114 Sub: 255.255.255.255 Standard-gateway: DNS-Server: 192.168.0.1 NetBIOS: activated To clarify my IP-situation: server is connected to router with 192.168.0.x, the test-client is in an external network connected to a router with 192.168.1.x, server-client connection is using static ips with 192.168.2.x Can anyone help me with this one? The VPN should be ok since I am able to establish remote access.

  Read the article

• Nested RDP and ILO/VMWare console sessions, latency and keystroke repetition

  - by ewwhite

  I'm working on a remote server installation entirely through ILO. Due to the software application and environment, my access is restricted to a Windows server that I must access through RDP. Going from that system to the target server is accomplished via HP ILO2 or ILO3. I'm trying to run a CentOS installation in an environment where I can't use a kickstart. I'm doing this via text mode, but the keystrokes are repeating randomly and it's difficult to select the proper installation options. For example: ks=http://all.yourbase.org/kickstart/ks.cfg ends up looking like: ks====httttttp://allll..yourbaseee.....org/kicksstart/ks.cccfg I'm doing this using Microsoft's native RDP client (on Mac and Windows). I've also noticed this before when running installations or doing remote work in nested sessions. Same for typing into a VMWare console in some cases. Is there a nice fix for this, or it it simply a function of the protocol(s)?

  Read the article

• Prevent zsh from trying to expand everything

  - by Attila O.

  Recently switched from bash, I noticed that zsh will try to expand every command or argument that looks like it has wildcards in it. So the following lines won't work any more: git diff master{,^^} zsh: no matches found: master^^ scp remote:~/*.txt . zsh: no matches found: remote:~/*.txt The only way to make the above commands work is to quote the arguments, which is quite annoying. Q: How do I configure zsh to still try to expand wildcards, but if there are no matches, just pass on the argument as-is? EDIT: Possibly related: scp with zsh : no matches found

  Read the article

• ¿How to set maximum downloads or sockets or whatever, in Apache and or PHP?

  - by Petruza

  I made a PHP script, running from my localhost, that streams files from a remote server and serves them. I do this so I can rename the files prior to the browser shows the dialog to save them, through header( "filename:..." ) Anyway, although the remote server allows many simultaneous file downloads at good rates, when they stream through my local apache/php I can't get more than 6 at the same time. When I try to download the 7th, the save as dialog appears as soon as the sixth download has finished. I'm almost sure this is some limit imposed by php.ini or apache's httpd.ini, but don't have a clue about which one is it. do you?

  Read the article

• Why does 1080p through a VGA cable fit my HDTV but is oversized when through an HDMI cable?

  - by GraemeF

  I have put together a new PC with a XFX GeForce GTX 260 graphics card and have it connected to my HDTV. First, I used an old VGA cable with a DVI to VGA adapter and plugged it in to my HDTV's VGA port. Running at 1920x1080 it fit the screen perfectly. Now, to avoid running another cable across the room, I have connected it with a DVI to HDMI cable to my TV's HDMI port, and the desktop at 1920x1080 is cropped by the edge of the screen. I have "fixed" the cropping by using NVIDIA's "Adjust desktop size and position" tool, which created a screen resolution of 1814x1022 to fit the screen, but this is no longer the TV's native resolution and confuses some software (e.g. WoW). Why does VGA work as expected, but HDMI is scaled up? Can it be avoided?

  Read the article

• RHEL 5/CentOS 5 - sshd becomes unresponsive

  - by ewwhite

  I have a number of CentOS 5.x and RHEL 5.x systems whose SSH daemons become unresponsive, preventing remote logins. The typical error from the connecting side is: $ ssh db1 db1 : ssh_exchange_identification: Connection closed by remote host Examining /var/log/messages after a forced reboot shows the following leading up to the restart: Dec 10 10:45:51 db1 sshd[14593]: fatal: Privilege separation user sshd does not exist Dec 10 10:46:02 db1 sshd[14595]: fatal: Privilege separation user sshd does not exist Dec 10 10:46:54 db1 sshd[14711]: fatal: Privilege separation user sshd does not exist Dec 10 10:47:38 db1 sshd[14730]: fatal: Privilege separation user sshd does not exist These systems use LDAP authentication and the nsswitch.conf file is configured to look at local "files" first. [root@db1 ~]# cat /etc/nsswitch.conf # # /etc/nsswitch.conf # passwd: files ldap shadow: files ldap group: files ldap hosts: files dns The Privilege-separated SSH user exists in the local password file. [root@db1 ~]# grep ssh /etc/passwd sshd:x:74:74:Privilege-separated SSH:/var/empty/sshd:/sbin/nologin Any ideas on what the root cause is? I did not see any Red Hat errata that covers this.

  Read the article

• Windows 2008 RRAS and PPPoE

  - by Massimo

  I'm trying to use Windows Server 2008's Routing and Remote Access Server to share an ADSL connection which uses PPPoE, but I'm having no luck. I can setup the connection as a broadband Internet connection in Windows, and it works. I can share it using Internet Connection sharing, and it works (but it's not what I need). I have installed and enabled the Routing and Remote Access Service and configured it for NAT with a demand-dial interface; I create the aforementioned interface using PPPoE with the exact same parameters used on the Windows connection; I connected it, and it seems to work: I can also see it gets its public IP address and DNS assigned correctly. But it just doesn't work. The server has no Internet connectivity at all, and PINGing anything on the Internet results in a cryptic "general error". Any help?

  Read the article

• Is there a serious issue with setting the SUID bit on tcpdump?

  - by Dean

  I'm running tcpdump on a remote machine, and piping the output to Wireshark on my local machine over SSH. In order to do this, I had to set the SUID bit on tcpdump. For background, the remote machine is an Amazon EC2 running "Amazon Linux AMI 2012.09". On this image, there is no root password, and it is not possible to log in as root. You can't use sudo without a TTY, and therefore you have to set the SUID. What are the practical risks of setting this bit on tcpdump? Is there any need to be paranoid? Should I unset it whenever I'm not capturing?

  Read the article

• Have SkyDrive not sync some subfolders of "SkyDrive"

  - by Bram Vanroy

  I am working with SkyDrive for a while now and it is GREAT! The only downside is that I am syncing my laptop and my desktop and that they don't have the same files. Example: For recording, I have Cubase installed on my laptop. This programme creates a folder "Cubase LE" in "My Documents". "My Documents" is being sync'd. This means, that on my desktop a folder will appear, named "Cubase LE". But it is not needed there at all! So what I'm looking for is an option to disable some folders from being sync'd. Can this be done? Like, right-clicking on a folder and selecting an option "Don't sync with SkyDrive". Thanks.

  Read the article

• Tutorial for configuring OpenVPN [on hold]

  - by user2699451

  I have been through 10+ tutorials on setting up a OpenVPN, and each tutorial gives a different problem... Does anyone know of a decent and helpful website/tutorial which I could go to to get it set up? I have been battling through it for almost 2 months now. Yes, I have also bugged forums.openvpn, but I think I have "reached my post limit" with them. I have to configure it remotely via ssh. UPDATE: okay, I have been asked to be more clear on the topic I followed this tutorial (as a example) - http://www.servermom.com/how-to-build-openvpn-server-on-centos-6-x/732/ I had no issues setting up, etc. except when I boot into windows and run the OpenVPN GUI Client, it connects and gives this error: WARNING: Bad encapsulated packet length from peer (21331), which must be 0 and <= 1576 -- please ensure that --tun-mtu or --link-mtu is equal on both peers -- this condition could also indicate a possible active attack on the TCP link -- [Attemping restart...] Here is my server config: port 1194 #- port proto udp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 reneg-sec 0 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /usr/lib64/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Co$ #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment$ client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 5 30 comp-lzo persist-key persist-tun status 1194.log verb 3 and my client config: client dev tun proto udp remote [server ip] 1194 # - Your server IP and OpenVPN Port resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 persist-key persist-tun ca ca.crt auth-user-pass comp-lzo reneg-sec 0 verb 3 OpenVPN Client Log: Thu Oct 31 11:51:29 2013 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Thu Oct 31 11:51:44 2013 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Thu Oct 31 11:51:44 2013 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Thu Oct 31 11:51:44 2013 LZO compression initialized Thu Oct 31 11:51:44 2013 Control Channel MTU parms [ L:1576 D:140 EF:40 EB:0 ET:0 EL:0 ] Thu Oct 31 11:51:44 2013 Data Channel MTU parms [ L:1576 D:1450 EF:44 EB:135 ET:32 EL:0 AF:3/1 ] Thu Oct 31 11:51:44 2013 Local Options hash (VER=V4): '2547efd2' Thu Oct 31 11:51:44 2013 Expected Remote Options hash (VER=V4): '77cf0943' Thu Oct 31 11:51:44 2013 Attempting to establish TCP connection with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCP connection established with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link local: [undef] Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link remote: x.x.x.x:1194 // after this it just hangs, nothing happens So I dont know what I am doing wrong but I am getting a bit impatient and on each forum I post this, I get stupid/unrelated/unhelpful answers...

  Read the article

• How can I make it difficult to install a new operating system on a certain computer?

  - by D W

  I want to host a website on a desktop computer running Ubuntu with a Windows virtual machine. I will give away the computer in exchange for a number of months of remote web hosting. I want to add some kind of lock (hardware or otherwise) so that the end users will have difficulty just reinstalling Windows and using the machine as they want, in contradiction to the contract. Ideally, I'd want the machine to die if reinstallation of the OS is attempted. It doesn't have to be completely insurmountable, but it has to be difficult enough to prevent casual reinstallation. Perhaps on bootup the system can check whether certain files exist on the computer and refuse to boot if they do not. I don't know if this is possible, but maybe BIOS is password protected, and searches for files before boot up. The files it looks for could be date sensitive, i.e. require remote replacement on a schedule.

  Read the article

• Managing Active Directory Group Membership with a Non-Administrator Account In Server 2008

  - by Laranostz

  I am running Server 2008 R2 in an Active Directory Domain Environment. I have created a group in Active Directory and I have delegated management authority to that group to a user. I want this user to be able to add and remove accounts as needed from that group so that they are exercising some measurement of control without giving them other authority. When I have the user attempt to access the Active Directory Users & Computers Console it prompts them for Administrator credentials. They are using Remote Desktop to access the server, because they do not have Windows 7, and firewall rules prevent using the Remote Management Kit. I do not want to provide them with any level of Administrative rights except the minimum required for them to add/remove users from this group. There are two servers that 'talk' to each other in this isolated environment, a domain controller and a member server, both are only reachable through RDP. Any suggestions?

  Read the article

• Socat and rich terminals (with Ctrl+C/Ctrl+Z/Ctrl+D propagation)

  - by Vi

  socat - exec:'bash -li',pty,stderr,ctty - bash: no job control in this shell What options should I use to get fully fledged shell as I get with ssh/sshd? I want to be able to connect the shell to everything socat can handle (SOCKS 5, UDP, OpenSSL), but also to have a nice shell which correctly interprets all keys, various Ctrl+C/Ctrl+Z, tab completion, up/down keys (with remote history). Update: Found "setsid" socat option. It fixes "no job control". Now trying to fix Ctrl+D. Update 2: socat file:`tty`,raw,echo=0 exec:'bash -li',pty,stderr,setsid,sigint,sane. Not it handles Ctrl+D/Ctrl+Z/Ctrl+C well, I can start Vim inside it, remote history is OK.

  Read the article

• Proxification rulte for System process

  - by kseen

  I'm trying to configure Microsoft Visual Studio 2010 remote debugging and ran into issue: while connecting to remote computer running MSVSMON, client computer sends SYN request for connection. It makes it under the System process (as I see it in TCPView). As every network apps should be configured to use proxy in our network, I'm trying to add devenv.exe to proxification rules to make its traffic goes thru LAN's proxy server. It doesn't help. So my question is how can I make that low-level-system traffic will go through local area network proxy server?

  Read the article

• Running command transparently over ssh

  - by jnsg

  By transparently I mean forwarding of: stdin, stdout and stderr standard signals (SIGHUP or SIGINT would be great for a start) As an example, consider these invocations of a (pointless) local and remote command: $ `cat - > /dev/null; sleep 10` < /local/file $ ssh user@host "cat - > /dev/null; sleep 10" < /local/file I can interrupt the first one with ^C just fine. But if I try this during the second one it only affects ssh, leaving the command running on the remote server if cat has already finished. I know about launching sshwith -t, but this way I can't send data via stdin. Is this possible with ssh alone at all?

  Read the article

• Windows 8 scroll lag

  - by samayres1992

  Don't have an issue with the desktop experience, but when it comes to the apps, scrolling in some of them is impossible to use correctly. Very laggy and jumpy, which is surprising because my computer has relatively high specs, only a year old. Scrolling using the manual scroll bar has no lag whatsoever it's simply whenever I use my touchpad. Maybe it's a touchpad issue? or more likely windows 8 as it seems fine in desktop view for scrolling? Any ideas where the problem may lie? Thanks

  Read the article

• Skype message sync and notifications - Windows 8

  - by Raykud

  The problem is that my messages don't seem to sync and neither do I get notifications from the Windows Store App. I have both, the desktop program and the Windows Store App, the problem is that whenever someone messages me I do not receive a notification of the App but I get one from the desktop program. The Skype app is running in the background and does not have disabled the notifications neither have turned on sleep notifications. I have to manually open the app and moreover, open the chat window of the one who is talking to me, then wait like 10 minutes and then the chat will get syncronized. in short: Notifications don't work even: if computer unlocked and Skype is running in background if computer unlocked and Skype is running in foreground These doesn't seem to help: Reboot doesn't affects skype. Having only the App opened. Uninstalling/reinstalling Is there a way to fix this? or is this an issue with the Skype app in Windows 8?

  Read the article

• Using Windows 7 drivers in Windows Server 2008 R2

  - by Robert Koritnik

  Maybe I should post this to http://www.serverfault.com. Windows 7 comes with all sorts of signed drivers so there's high probability that all drivers for your machine will be installed during system setup. On the other hand Windows Server 2008 doesn't event though it's practically the same OS when it comes to drivers. But I know that this has a very good reason. It's a server product, not a desktop one. But the thing is that many power users and developers use server OS on their workstations which are normally desktop machines and would need Windows 7 driver spectrum... Question I know I've been reading about some trick on the internet that first installed Windows 7 on the machine, than do something to get either all Windows 7 driver collection or just those installed, and then install Windows Server 2008 and use those drivers. The thing is: I can't seem to find these instructions on the internet any more. If anybody knows where these are please provide the link for the rest of us.

  Read the article

• How to add the Windows defender into Windows Explorer's right click menu to scan a particular drive/folder/file on demand?

  - by avirk

  There is no option in Windows Explorer to scan a particular drive (or file) on demand by right clicking on it in Windows Explorer as we had in Windows 7 with Microsoft Security Essentials or like other antivirus solutions. I know we can run a custom scan for the particular drive or specific folder but that process is too lengthy and time consuming. The guide How to Add a "Windows Defender" Cascading Desktop Context Menu in Windows 8 explains how we can add Windows Defender in the desktop right click menu, so I'm curious, is there a way to add it in the Windows Explorer right click menu to launch a search whenever I need to?

  Read the article

< Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >