Search Results

Search found 18927 results on 758 pages for 'remote desktop'.

Page 284/758 | < Previous Page | 280 281 282 283 284 285 286 287 288 289 290 291  | Next Page >

  • SBS 2011 on different subnet than domain computers

    - by Ravi
    The setup is as follows: SBS 2011 in datacentre on subnet A Domain PCs at another location on subnet B There is a site-to-site VPN. The domain PCs have joined the domain and have the SBS as their primary DNS server. The domain PCs can ping the DC but the problem is that the DC cannot ping any of the remote subnet (subnet B) SBS --Switch -- Router A ------------------- Router B -- Switch -- Domain PCs What is strange is that router A can ping any host on the subnet B. Another host on Subnet A can also ping any host on subnet B. It's only the DC which cannot ping anything to that specific remote subnet B. I did a tracert from the SBS to router B. The packet reaches Router A from the SBS but then it fails. Am I missing some specific settings that needs to be done when SBS is on a different subnet than its member pcs ?

    Read the article

  • Any ideas for automatic initial/scripted configuration of a NetApp?

    - by maddenca
    The background is to make a solution where we can automate as much as possible the building up of ‘pods’ that include server/network/storage and that will be built at remote sites. In an ideal world would be that we create a single management server which is preconfigured with DHCP/TFTP/or whatever. This management server is racked with a CISCO UCS, FAS31x0, etc. at a build site and is then transported to the final customer site where on power it almost configures itself, or at least bootstraps itself far enough that a remote skilled 'expert' can complete the setup of the pod. Ideas (doesn't have to resemble 100% of the above) would be helpful.

    Read the article

  • Disable MOUSE wakeup when doing suspend on UBUNTU

    - by Shadyabhi
    When I do SUSPEND on ubuntu, in order to wake up, i can just move the mouse and the computer will wake up. But, I dont want that the computer is waked up when I move my mouse. How can I do that? My /proc/acpi/wakeup file:- shadyabhi@shadyabhi-desktop:~$ cat /proc/acpi/wakeup Device S-state Status Sysfs node SLPB S4 *enabled P32 S4 disabled pci:0000:00:1e.0 UAR1 S4 disabled pnp:00:09 ILAN S4 disabled pci:0000:00:19.0 PEGP S4 disabled PEX0 S4 disabled pci:0000:00:1c.0 PEX1 S4 disabled pci:0000:00:1c.1 PEX2 S4 disabled pci:0000:00:1c.2 PEX3 S4 disabled pci:0000:00:1c.3 PEX4 S4 disabled pci:0000:00:1c.4 PEX5 S4 disabled UHC1 S3 disabled pci:0000:00:1d.0 UHC2 S3 disabled pci:0000:00:1d.1 UHC3 S3 disabled pci:0000:00:1d.2 UHC4 S3 disabled EHCI S3 disabled pci:0000:00:1d.7 EHC2 S3 disabled pci:0000:00:1a.7 UH42 S3 disabled pci:0000:00:1a.0 UHC5 S3 disabled pci:0000:00:1a.1 UHC6 S3 disabled pci:0000:00:1a.2 AZAL S3 disabled pci:0000:00:1b.0 shadyabhi@shadyabhi-desktop:~$

    Read the article

  • Is there a way to see what is typed or websites visted when a spouse is using google chrome in incognito ?

    - by Ken
    My spouse and I have 2 laptops both running windows 7 and I have 1 desktop running vista. I have reason to believe she is cheating and I want to watch her internet usage, She is always using google chrome in incognito mode. I have tried a few keyloggers but they never seem to be able to get the keystrokes when she is on google. I dont know if there is a way I can network them so they go thru my desktop then to the internet. We are using Brighthouse cable internet. any ideas would be great thank you

    Read the article

  • X11Forwarding on MacOSX (Leopard/Snow Leopard)

    - by Shyam
    Hi, I have some remote boxes, which are a bunch of Mac Mini's. I access them now through SSH, and it fits my needs to do the maintenance. In the past, I used X11Forwarding with Linux boxes, when I was still using Debian myself, and I was able to run a specific application as if it was natively present (Firefox). I haven't succeeded to do this yet, but I assume because of the BSD underneath the fancy Apple GUI should be able to do such a task similar. I am aware of the remote administration, but I rather keep access limited to SSH on these boxes for inbound connections. Background information about the why's, tips, advice and comments are all helpful! Thanks!

    Read the article

  • help setting up an IPSEC vpn from my linux box

    - by robthewolf
    I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

    Read the article

  • I can't launch any Win8 apps after upgrading to Windows 8.1

    - by locka
    I just upgraded to 8.1 and now none of the Metro apps start. The issue is that if I start any metro app, including the Store and PC Settings they immediately fail. The classic desktop is fine, as are standard programs, it's just the metro apps. If I look in the system event log I see errors like this: *Activation of application winstore_cw5n1h2txyewy!Windows.Store failed with error: This application does not support the contract specified or is not installed. See the Microsoft-Windows-TWinUI/Operational log for additional information.* In addition the tiles in metro have a small cross icon on them: I suspect that my Live ID (which I somehow managed to skip during update) is not set properly and consequently none of the online stuff works. But how do I fix this? I can't start PC settings, I can't start store. I see no way in the classic desktop of setting these things. I don't want to have to reinstall for this. Is there a simple fix?

    Read the article

  • How to copy files between windows 7 professional and enterprise machines?

    - by WilliamKF
    I've got a desktop system running Windows 7 Professional and a laptop running windows 7 Enterprise in a domain-joined computer and I need to copy around 50 GB of files from the Enterprise machine to the professional one. I'd rather not burn a bunch of DVDs or use my tiny flash drive of 1 GB to do the transfer. How can I mount a drive from one of the computers to the other so that I can just drag and drop? I tried using a homegroup, but the windows 7 Enterprise laptop does not see it from the professional desktop and the laptop cannot make its own homegroup since it belongs to a domain.

    Read the article

  • rsync to EC2: Identity file not accessible

    - by Richard
    I'm trying to rsync a file over to my EC2 instance: rsync -Paz --rsh "ssh -i ~/.ssh/myfile.pem" --rsync-path "sudo rsync" file.pdf [email protected]:/home/ubuntu/ This gives the following error message: Warning: Identity file ~/.ssh/myfile.pem not accessible: No such file or directory. [email protected]'s password: The pem file is definitely located at the path ~/.ssh/myfile.pem, though: vi ~/.ssh/myfile.pem shows me the file. If I remove the remote path from the very end of the rsync command: rsync -Paz --rsh "ssh -i ~/.ssh/myfile.pem" --rsync-path "sudo rsync" file.pdf [email protected] Then the command appears to work... building file list ... 1 file to consider file.pdf 41985 100% 8.79MB/s 0:00:00 (xfer#1, to-check=0/1) sent 41795 bytes received 42 bytes 83674.00 bytes/sec total size is 41985 speedup is 1.00 ...but when I go to the remote server, nothing has actually been transferred. What am I doing wrong?

    Read the article

  • KVM Guest not reachable from host

    - by Paul
    Hello, I'm running Ubuntu server 9.10, installed KVM etc. Created the bridge network following instructions on help.ubuntu.com/community/KVM/Networking Created a windows 2008 guest using virt-install command line (using virt-manager GUI from a remote Ubuntu desktop would not let me select the ISO location). I can however use a remote virt-manager to connect to the guest and complete the windows install. Within windows 2008 I changed the IP address but cannot ping from outside world. The bridge network appears fine - I'm not sure what else to look at! Here is the interfaces file: The loopback network interface auto lo iface lo inet loopback The primary network interface auto eth0 iface eth0 inet manual # auto br0 iface br0 inet static address 60.234.64.50 netmask 255.255.255.248 network 60.234.0.0 broadcast 60.234.0.255 gateway 60.234.64.49 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 auto eth1 iface eth1 inet static address 192.168.12.2 netmask 255.255.255.0 broadcast 192.168.12.255 The ip of the windows server is 60.234.64.52 What else should I check? Regards Paul.

    Read the article

  • External hard drive not disconnecting and leaving 'ghost drives' on my PC

    - by Shane
    I use a Seagate FreeAgent on my laptop and PC. While it works fine most of the time, sometimes when I try to safely disconnect it, it says the files are in use. Obviously I have by that time shut down all applications. Now with my laptop, a Toshiba Satellite, I shut down the computer and unplug the Seagate and no ghost drives are found. But no matter what I do with my desktop, it continues to create 'ghost drives'. Is this due to a feature in the external hard drive, and if so, would anyone have an idea how I can fix it? I am getting tired of deleting the 'ghost drives'. Both my laptop and desktop use Windows 7.

    Read the article

  • How to quickly switch monitors on multi-monitor setup?

    - by Saxtus
    At my desktop PC, I have 3 displays hooked up on my Palit GeForce GTX 480 to extend my desktop: DVI: Samsung SyncMaster T220 (22" 16:10, 1680x1050, as my main) DVI: Samsung SyncMaster 940BF (19" 4:3, 1280x1024) HDMI: Sony Bravia KDL-32D3000 (32" 16:9, 1360x768) As expected, the GFX card can only utilize 2 of the displays at any given time, so I have to manually switch using Windows' "Display Properties" dialog, each time I want to switch between them. I've tried UltraMon, DisplayFusion and PowerStrip (so please don't refer me to a question where those are given as solutions) but they are unable to switch monitors. Instead they can only change display resolutions and settings on the existing active monitors, with specially weird results when I've saved the monitor states and then tried to switch monitors using the saved states! Any idea on how to bypass the awful "Display Properties" dialog and it's "confirm your change" timer?

    Read the article

  • How to supply parameters in URI schema?

    - by abhishekgarg
    I just started working with URI schema and successfully created one in Windows and Linux as well, but I am not able to parse any parameters to it. In Linux I am trying to open a file "test.py" in gedit, so for schema part I used these commands: gconftool -2 -t string /desktop/gnome/url-handlers/geditapp/command "gedit %s" gconftool -2 -t bool/desktop/gnome/url-handlers/geditapp/enabled true This is creating the URI protocol and I'm able to open the application with the Web-browser, but its not taking the parameters for the file I want to open, so I'm using the following command: <a href="geditapp:/opt/test/myfile.py">open</a> Which opens the gedit but without the file. Can someone please help me with this?

    Read the article

  • A keyboard shortcut from a sequence of keystrokes for Linux

    - by Little Bobby Tables
    I am looking for a way to define an Emacs-style keys sequence as a keyboard shortcut in Linux - Specifically, in Gnome, but more general solutions are also acceptable. For example, I would like a sequence like "Alt-w t" (that is, first press Alt-w and then t) to open a terminal, "Alt-w c" to close a window, and so on. The rationale behind this question is twofold: Make more use of desktop-wide keyboard shortcuts Make an old keyboard, that has no Win key, usable with desktop-wide keyboard shortcuts, without causing too many collisions with application - Specifically with Emacs. Thanks!

    Read the article

  • Deleting... dialog box stays on screen for over a minute when deleting one small file

    - by stacey.richards
    Every now and again I log into a Windows Server 2003 box with a remote desktop connection and delete one small file. When I do this, the Deleting... dialog box appears and remains on the screen for well over a minute. After the dialog box disappears, if I delete another small file, the Deleting... dialog box appears then disappears quickly. Why does it take so long to delete the first file after logging into a Windows Server 2003 box with a remote desktop connection? Is there a trick to speeding it up?

    Read the article

  • Squid traffic tunneled through VPN

    - by NerdyNick
    So what I'm trying to do is have a Squid Proxy run on 1 machine along side a VPN connection. What I want to happen is all traffic running though the Squad Proxy would run though the VPN for its outbound. ie Desktop - (Squid Proxy - VPN) The goal is to allow my desktop selective tunneling through the VPN. So that Instant Messaging and the like that do not need to run through the VPN can go through my normal traffic. Typically I would go though a SSH Proxy but currently am forced to use VPN to gain entry into the office, and a Squid proxy seemed like it might work out the easiest for what I am needing. EDIT Realize I forgot to actually state what problem I'm running into. I have the Squid setup and verified it works, but once I connect to the VPN. All requests to Squid get accepted but Squid is unable to make the request over the VPN. So the client ends up just sitting there.

    Read the article

  • how to disable local logins to a mac snow leopard machine?

    - by Wang
    I have a maintenance script that needs to run uninterrupted, so I'd like some way to disable local user logins. Right now, the solution is to send SIGSTP to the loginwindow process, which is suboptimal for several reasons. The most important of them is that the observed behavior is a login prompt that appears to accept the user's credentials but then hangs on a blank desktop before the menu bar or dock or desktop icons appear. This has led to users "fixing" the problem by rebooting the machine. Is there a better way to disable local logins? We currently use iHook, so if there's any way to abort a login from within the login hook, that would integrate nicely with our current setup. Unfortunately, Apple doesn't seem to have documented exactly what would cause Mac OS to abort the login.

    Read the article

  • How to set up a wireless AP with a linux box and SOCKS proxy

    - by user50455
    I've got: (1) Linux box (Arch linux to be precise, but that doesn't really matter) (2) Ethernet connection on it (say, eth0) (3) Socks proxy on a remote site (say, remote :port), which can be accessed through (2) (4) Wireless card on local linux box (say, eth1) So, the task is: create a wireless access point using (4) on local site (1) in such a way that all connections from it will go through proxy (3). E.g., when one simply connects to that AP (well, there should be DHCP or something for that) and goes to serverfault.com, all the traffic goes through that SOCKS proxy. I'm just asking for the digging direction and some references, not step-by-step tutorial. Thanks in advance

    Read the article

  • Gitosis on Mac OS X (Snow Leopard)

    - by Shyam
    Hi, I have a Snow Leopard box, where I have gitosis installed (Warning: noob alert), added a git user and I am able to remotely login to the machine with ssh. Locally, I can 'clone' my created repositories, as I can 'clone' the gitosis-admin too. Works perfect. I clone these using the 'git' user. git clone git@my-remote-machine:reponame.git remotely logged in, what doesn't work: git clone git@localhost:reponame.git However on that same remote machine where the repositories live, I can't clone from the localhost. It asks for a password, which wasn't created as far as I know. What am I doing wrong? Thank you for your replies!

    Read the article

  • How to repair a broken .EXE file association

    - by Pointy
    After (hopefully) scrubbing viruses out of a Windows 7 installation (after deciding not to simply run over the laptop repeatedly with my car), I've got everything almost back to normal. The only lingering issue I have is that for my non-admin users, the ".exe" file extension doesn't work. That is, clicking on the various desktop application links results in a "How do you want to open this?" dialog. I've been through the alleged registry fixing from "winhelponline" and that had absolutely no effect. I've tried running "assoc" for the affected users, but it reports the .exe association to be "exefile" even though it persistently does not work. Right-clicking on a desktop icon and then choosing "start" does successfully open an application, but that's clearly a terrible situation. For my admin user, things seem to work fine. What do I need to do to get things working?

    Read the article

  • Killing Self-resurrecting Files

    - by Zian Choy
    Local computer: Dell desktop Windows XP Named "5" Server: Windows Server 2008 Named "W" Whenever I delete a file, log out, and log in, the file reappears. The files all supposedly live on the server (e.g. "\W\Home$\zchoy\Desktop") but even when the files are deleted from the server and the local computer, they come back. I've already tried resetting the offline files cache. I tried deleting a file and then synchronizing with the server. The file didn't come back. However, as mentioned earlier, the file comes back once I log out and log in.

    Read the article

  • Solaris to Linux conversion: Use VxFS or GFS?

    - by w00t
    We're a Solaris shop looking at RedHat Enterprise Linux and one of the things we're wondering is if we should keep Veritas Volume Manager + FileSystem or go with LVM+ext3 or RedHat's preferred cluster filesystem solution, GFS. One of the things we like about Veritas is that it can use Veritas Volume Replicator to have a remote copy of important filesystems. This functionality seems to be missing from RedHat, DRBD doesn't seem to be packaged in RHEL... So my questions are: Does anybody use VxFS/VxVM/VVR on Linux? Thoughts, experiences? Comparison with LVM+ext3? Anybody using GFS? Thoughts, experiences? Do you do remote replication for disaster recovery, and if so, how? Is there a standard RedHat way?

    Read the article

  • Windows Home Server - Can't log in - A problem is preventing Windows from accurately checking the license for this computer. Error Code: 0x8007007e

    - by 1337ingDisorder
    Subject header pretty much covers it. I have a windows Home Server which can only be accessed through remote desktop. I could log in for ages, but for the past couple weeks I haven't been able to log in. As soon as I enter my username/password and click OK, I get an alert dialog stating the following: "A problem is preventing Windows from accurately checking the license for this computer. Error Code: 0x8007007e" When I click "Ok" (the only option) the dialog closes and my remote session closes. How can I get around this? I've tried powering down the machine and powering it back up. Same results.

    Read the article

  • Open Windows Server 2012/Windows 8 Start Menu

    - by bmccleary
    I realize that Windows Server 2012 (and Windows 8) removed the start menu button and replaced it with moving your mouse to the upper right corner of the screen. This works fine when the desktop is full screen. However, I access all my servers through windowed RDP connections (or through the Hyper-V console window) and in this case, the desktop is not full screen. Therefore, in order to open the new "start" menu, I have to slowly move my mouse very carefully within the window to just a few pixels within top right corner of the window in order to open the menu. Also, because the session is windowed, the default hot keys (Windows + D, etc.) won't work. There has got to be an easier way. Has anyone else experienced this frustration?

    Read the article

< Previous Page | 280 281 282 283 284 285 286 287 288 289 290 291  | Next Page >