Search Results

Search found 12013 results on 481 pages for 'dvd drive'.

Page 281/481 | < Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >

• How to reinstall bootloader after migration to SSD

  - by hijarian

  I must say, it was difficult to name this question. Basically, I need to properly reinstall the bootloader on my system, because I already have the working system disks for my OSes. The long story is this: I had the large slow HDD with Windows7 & Debian Wheezy dual-boot on it, perfectly bootable. Then, I ordered the SSD drive and prepared my system partitions to fit onto the much smaller SSD. I wanted the following schema: 128 GB Windows 24 GB / on Debian 86 GB /home on Debian Strange size for /home because there's no such thing as true 256GB disk drive. So, I've prepared such a partitions on my initial HDD and installed the new SSD and then I loaded the GParted live USB (can't remember now how it was really named), and then just copypasted the partitions from HDD to SSD. So, now I have the following partitions across the physical disks: SSD 128 GB copy of original Windows partition 24 GB copy of presumably Debian / 86 GB copy of presumably Debian /home HDD 128 GB Windows 24 GB / on Debian 86 GB /home on Debian ... several other partitions with non-system data ... And the behavior of the system right after the Ctrl+C, Ctrl+V in GParted was as follows: no GRUB, system boots right into the Windows on HDD. In BIOS settings are to boot from SSD first. I managed to create the Debian Testing installation USB and loaded it into the rescue mode, found that it identified my SSD as /dev/sda and installed the GRUB to the /dev/sda. Now my system loads the GRUB which lists both Windows and Debian. From HDD. So, I am now back into initial position. Please, how I should set up the GRUB so it'll load the OSes correctly from SSD? Should I fire up my Debian, fiddle with the GRUB's config and reinstall it again to the same place (at SSD)?

  Read the article

• How to get rid of "Maxback Engine" for good?

  - by Jonik

  I used to have a Maxtor Shared Storage II network drive; it broke down long ago already. (Later I tried to recover some data from it, and partially succeeded, but haven't yet fully documented it on that question.) Anyway, I just noticed there are still some lingering bits remaining of the (thourougly crappy) software that came with the Maxtor device: a background process called "MaxBack Engine". I googled around a bit and found something related but not very useful: http://www.straitmac.com/jforum/posts/list/600.page http://discussions.apple.com/thread.jspa?threadID=725692 Under /Applications I found "Maxtor EasyManage.app" which I used to use for controlling the drive, and showed it some "rm -rf". Before deleting, I noted that the bundle did contain "MaxBack Engine.app" under Content/Resources. But still, after reboot, the "MaxBack Engine" process is back. I did notice though that it only appears when logging in with my usual user account; with another account it wasn't launched. So, dear Mac gurus, what could I do about this pest? I guess I could fall back to some Unix hackery and write a cronjob that kills any process with that name, but obviously it'd be nicer to be able to clean up from my computer everything left behind by Maxtor's piece of software.

  Read the article

• How do I stop linux from trying to mount android phone as usb storage?

  - by user1160711

  When I plug in my Motorola Triumph to my fedora 17 linux box USB port, I get an endless series of errors on the linux box as it desperately attempts to mount the phone as a USB drive. Stuff like this: Jun 23 10:26:00 zooty kernel: [528926.714884] end_request: critical target error, dev sdg, sector 4 Jun 23 10:26:00 zooty kernel: [528926.715865] sd 16:0:0:1: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 23 10:26:00 zooty kernel: [528926.715869] sd 16:0:0:1: [sdg] Sense Key : Illegal Request [current] Jun 23 10:26:00 zooty kernel: [528926.715872] sd 16:0:0:1: [sdg] Add. Sense: Invalid field in cdb Jun 23 10:26:00 zooty kernel: [528926.715876] sd 16:0:0:1: [sdg] CDB: Read(10): 28 20 00 00 00 00 00 00 04 00 If I go ahead and tell the phone to allow linux to mount the USB storage, the messages stop, and I get a mounted drive, but if all I want to do is use the debug bridge, my log on linux will continue to fill with this junk. Is there some udev magic I can do to make the system ignore this particular device as far as usb storage goes? I just noticed that if I tell the phone to enable USB storage, let linux recognize the new disk, then tell the phone to disable USB storage again, I get one additional log message about capacity changing to zero, but the endless spew of messages stops, so I guess one work around is to enable and disable USB right away.

  Read the article

• Is this normal or does my AVG anitivirus have a virus? [closed]

  - by user390480

  Possible Duplicate: Computer is infected by a virus or a malware, what do I do now? [Note: This is not a duplicate and should not be closed as a duplicate as this is nothing like the other question. I am not asking if I have a virus, nor am I asking "what do I do now". I know that I have a virus and I know what to do. However, I am asking if these are normal AVG ads or if it has been taken over.] My Windows XP PC started acting strange and I am right now actually in Linux running off of a USB drive. I am running Avast under Linux and it has discovered some viruses on my XP drive. Some of the strange things happening in XP were: I could not get to Google.com My Hosts file was set to hidden and read only My Hosts file had an entry of ::1 And AVG had ads in it I've never seen before. Maybe it is normal but I Binged for AVG anti-virus and become.com but found no information. (The red lines and question mark are by me) Any thoughts?

  Read the article

• poor performance when deleteing many files

  - by choppy

  I've got two machines: The first is IBM Blade with 24 cores 96GB RAM and single local hard drive with 278GB divided to 4 partitions: 1. c: - 40GB; 3GB free 2. d: - 40GB; 37GB free 3. e: - 198322GB; 198.1 free 4. 100MB (EFI system Partition) Formatted with GPT The other is pizza server with 4 cores 8GB RAM and single local hard drive with 273GB divided to 3 partitions: 1. c: - 136.81; 20GB free 2. d: - 88.74GB; 87.91 free 3. e: - 47.85GB; 46.91 free Formatted with MBR I have two scripts, the first creates 20,000 files in one directory, each file size is 192KB, the second delete the folder (recursive) and prints how much time it toke to delete all files. The problem is on the first server (blade) it takes about 2 minutes to delete all 20,000 files while on the second (pizza) it takes about 4 seconds!? Both servers have clean windows server 2008R2 with no special application running on background. Any ideas what is going on?

  Read the article

• NTFS frequent corruption when writing many small files, index $I30 error

  - by david sedai

  I'm running Windows 7 Ultimate on a laptop with a 500G HDD, and had all partitions formatted as NTFS. I do a lot of programming and LaTeX typesetting, both of these involves a large amount of reading/writing/deleting to a lot of small files, such as C++ library headers or LaTeX packages. The problem is that frequently, when there is a large number of writing to files, the partition being written to often corrupts, the chkntfs e: returns dirty, where e: is the partition being written. I've re-formatted the drive, I've contacted the laptop manufacturer and had the HDD checked, the HDD is not faulty, there are no bad sectors, and I've tried a brand new HDD, to no avail, and the other partition on the same physical drive doesn't have this issue. I'm pretty sure that it's no hardware related. I've searched the Microsoft support pages, one page http://support.microsoft.com/kb/982018 provides an update for Advanced Format Disks, which I've already installed. The chkntfs log shows $130 index errors. I'm at a loss here. Can anyone help? Thanks in advance.

  Read the article

• How to merge arbitrary snapshot into base vdi in Virtualbox

  - by jmathew

  I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid <path/to/vdi> Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID?

  Read the article

• Strange Internet Connection issues

  - by Nodren

  I'm attempting to troubleshoot problems with a laptop computer(HP 8510w) while it's connected to a server of mine via Remote Desktop. I double checked all the settings on the win2k3 server for remote desktop to verify that remote desktop isn't what's causing the disconnect issues, and other people using different computers/laptops can all connect to remote desktop correctly with no issues. These problems happen specifically when the laptop is connected via wifi(several different wifi sources, so it's not an ISP issue) as well as connected via a Verizon data card. However there's no network downtime when the laptop is resting in the docking station and plugged into the network with the remote desktop server. These problems have also only recently occurred since a recent hard drive failure in which a new hard drive was purchased and the laptop had a fresh install of windows xp professional. There's no special software used on this machine, just office 2003. So my question is, what could cause two types of internet access to fail while other types do not? If it is infact related to the win2k3 server, why is this particular laptop getting disconnected when others are not and are all on at the same time?

  Read the article

• Missing whole disk device in OpenSolaris

  - by Jeff Mc

  I have begun experimenting with Solaris and ZFS as a NAS. All was going very smoothly until I had a drive failure. When I replaced the drive, I no longer have a device file mapped to the whole disk. /dev/dsk/c7t3d0 does not exist but c7t2d0 and c7t4d0 both do. Also the sd@3,0:wd file under the /devices/ tree is non-existent. Do I have to prepare/partition the disk somehow to cause the whole disk device to exist? Here are a few outputs that might be useful. jeffmc@ats-ds2:/dev/dsk$ zpool status pool: datapool state: DEGRADED status: One or more devices could not be opened. Sufficient replicas exist for the pool to continue functioning in a degraded state. action: Attach the missing device and online it using 'zpool online'. see: http://www.sun.com/msg/ZFS-8000-2Q scrub: none requested config: NAME STATE READ WRITE CKSUM datapool DEGRADED 0 0 0 mirror-0 DEGRADED 0 0 0 c7t2d0 ONLINE 0 0 0 c7t3d0 UNAVAIL 0 0 0 cannot open mirror-1 ONLINE 0 0 0 c7t4d0 ONLINE 0 0 0 c7t5d0 ONLINE 0 0 0 jeffmc@ats-ds2:/dev/dsk$ zpool replace datapool c7t3d0 cannot open 'c7t3d0': no such device in /dev/dsk must be a full path or shorthand device name jeffmc@ats-ds2:/dev/dsk$ sudo format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c7t0d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@0,0 1. c7t1d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@1,0 2. c7t2d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@2,0 3. c7t3d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@3,0 4. c7t4d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@4,0 5. c7t5d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@5,0

  Read the article

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• effective back-up using Raid / Win7 back-up

  - by Job

  I have a stand-alone pc system with two 2 tb harddiscs, one of which configured as Raid1, i.e. mirorring. The operational drive is partitioned. I use an external 1 tb harddisc for back-up using Windows 7 back-up facility which will be swapped weekly and stored on other premises. I back-up all partitions AND allow a system back-up. All application software is on the C: partition. Questions: How can I see whether Raid1 is working; i.e. is doing its job. All I see now is a status message in the start-up procedure that says its status is normal. How can I see used or available space on Raid 1? The Win-7 backup allows for 1 schedule only as far as I can see. I want daily back-ups of data. However due to the single schedule I am forced to do the time-consuming system back-up and c: back-up as well. Is there a way to activate two schedules allowing a frequent (daily) data back-up and a system back-up with c: drive back-up on a say weekly basis? Of course it can be forced by hand but I am likely to forget that. I am not the programming type of person so looking for simple and controllable solutions. Thank you - any help is apreciated.

  Read the article

• Methods to transfer files from Windows server to linux server

  - by Raze2dust

  Hi, I need to transfer webserver-log-like-files containing periodically from windows production servers in the US to linux servers here in India. The files are ~4 MB in size each and I get about 1 file per minute. I can take about 5 mins lag between the files getting written in windows and them being available in the linux machines. I am a bit confused between the various options here as I am quite inexperienced in such design: I am thinking of writing a service in C#.NET which will periodically archive, compress and send them over to the linux machines. These files are pretty compressible. WinRAR can convert 32 MB of these files into a 1.2 MB archive. So that should solve the network transfer speed issue. But then how exactly do I transfer files to linux? I could mount linux drive on windows server using samba, or should I create an ftp server, or send the file serialized as a POST request. Which one would be good? Also, I have to minimize the load on the windows server. Mount the windows drive on linux instead. I could use the mount command or I could use samba here (What are the pros and cons of these two?). I can then write the compressing and copying part in linux itself. I don't trust the internet connection to be very stable, so there should be a good retry mechanism and failure protection too. What are the potential gotchas in these situations, and other points that I must be worried about? Thanks, Hari

  Read the article

• Very slow context menu in Windows 8

  - by burzum

  I've installed Windows 8 Pro on a blank new SSD, the system is on c:\. I do not think this problem was existent when I started using Windows 8 but I think it started to happen after I've symlinked (mklink /D) a folder from another drive, a SATA drive, to c:\xampp\htdocs. When I right click a file or folder inside the symlinked folder it always takes at least ~5-10 seconds until the context menu comes up. This also happens sometimes, but not all the time for files and folder outside of the symlinked folder. Also when I delete folders the delete folder dialog seems to get locked and does not continue. When I delete a folder using rmdir from the command line it works fine and pretty fast. It appears to me like the file explorer in Windows 8 is pretty bad compared to any other Windows I've used before? Any idea how to get these problems solved? I've already removed a lot of context menu entries; the only ones left are the tortoise git context menus but I'm sure that's not the problem.

  Read the article

• Acer recovery disks not bootable?

  - by user13743

  We got a new Acer laptop with Vista installed at work. As it's getting ready to go out in the field, we wanted to do a burn-in test on it. We made the recovery DVDs before we ran the test. Part of the burn-in was bonnie++, which does a destructive read/write test of the hard drive. The machine passed with flying colors, but after trying to boot to the recovery DVD to being re-installing the system, the machine began to try PXE boot after a while. After doing some googling, it appears these 'recovery' disks expect a certain recovery partition to exist on the hard drive, and are in fact not bootable at all, and are useless in absence of the recovery partition. Is this the case, and is this "The Way Things Are" with all PC manufacturers and Windows Vista+ nowadays? How do I get my hands on actual bootable DVDs? I've emailed Acer support. I see an option on their site to purchase recovery disks, but I have the suspicion that these are the same non-bootable disks that I burned on the new system. Will Acer provide actual boot disks?

  Read the article

• Dual-booting Windows 7 and Ubuntu

  - by CFP

  Hello everyone, I've just received my Dell Studio 17 laptop, which comes with Windows 7 x64 preinstalled. I'm having quite a hard time installing ubuntu on it. First of all, here is how I partitioned the drive using GPartEd: |==Dell utility partition==|==Dell Recovery partition==|==Windows 7==|[==Ubuntu==|==Data partition==]| Where [] denotes an extended partition. Here are the steps I completed: I used GParted to create this structure, keeping windows 7 installed I booted ubuntu LiveCD, and installed it on the right partition I let it install grub automatically I rebooted intu ubuntu I went back to windows 7, no problems I then rebooted. Grub was gone. I used Super Grub Disk to restore grub, it didn't work. I tried to boot into ubuntu from supergrubdisk, but grub couldn't fint the boot folder I then reinstalled ubuntu, went through the same steps, but there SGD did boot my ubuntu I reverted to the previous version of grub, and installed it on my hard drive It worked, but trying to boot win7 got me the "No MBR, press Ctrl+Alt+Del to reboot" error I used the windows 7 cd to restore the MBR (the auto wizard didn't work, had to rebuild the mbr from command line Now Ubuntu is gone. 7 works fine I read a lot about this, and realized that many people could simply not boot win7 again after encountering this problem. Now I'd like to restore GRUB, but I really won't go through the hassle of doing a full new cycle of installing/reinstalling everything again. Is there a GRUB guru around, to provide me with a detailed guide to not screwing everything up once again? Thanks a lot!

  Read the article

• Why are certain folders in my XP network share really, really slow?

  - by bikefixxer

  I have a workgroup set up with Windows XP. My file "server" is running XP Pro and the clients are running XP home. I've turned simple file sharing off on the server because certain clients need access to certain folders and not to others, and I want to keep it that way. Therefore, I've used the granular sharing/security settings to enable certain clients access to certain folders. I'm using the net use command in a batch file on the clients to add the share when they logon so it's always available via a mapped drive or a shortcut. On some clients "My Documents" points to the mapped drive, but all of the local and application settings stay local. Everything works well except for accessing a certain folder on the network. It contains a lot of random batch files and self-executable programs I use for diagnostics and what not, and nearly every time I open the folder the computer hangs for 15-60 seconds. This happens on every machine, including the server (but not nearly as often as the clients). I've searched high and low and cannot figure it out and it's driving me crazy. Here are all the things I've tried to no avail: Disabled firewall (XP) and anti-virus (ESET NOD32) Deleted any desktop.ini file I can find in the share Disabled "automatically search for network folders and printers" Disabled "remember each folder's view settings" Set HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer NoRecentDocsNetHood = 1 Tried with mapped drives and with UNC shortcuts Ran CHKDSK Removed Read-Only attribute from all folders (well, tried to remove, it always came back on with a half check) Added the server's static IP to the hosts file on the clients I've tried monitoring the server's performance to see if anything makes sense. Occasionally the issue coincides with a spike in pages/sec (memory) but not always. Other than that, everything else seems normal. The anti-virus would seem to be the most likely cause to me considering the batch files and what not, but it still hangs when it is completely disabled. I'm at a loss and if anyone can help me with this I'd greatly appreciate it!

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• Can I boot up a virtual machine natively?

  - by Anshul

  My question is: Is is possible to run a virtual machine natively on your hardware if you have installed the proper drivers etc? In other words, can I use a VHD as a regular hard drive to boot from? The reason I want to do this is that I do both graphics-intensive and audio-intensive work, but my computer is not powerful enough to handle both at the same time and many times I install a bunch of audio programs that I don't want affecting the stability of my graphics programs. Basically I wanted to have sandboxing between the two sets of applications. So I tried running the graphics-intensive programs in a VirtualBox VM and the audio-intensive work natively (simply because it's a pain to route ASIO audio devices in/out of VirtualBox). This kind-of works - the graphics-intensive stuff is tolerable, but still relatively slow, because it's running inside a VM. So my next idea was to just dual-boot and install the graphics and audio programs in separate partitions but I frequently use them in tandem, so it wouldn't be practical to reboot my machine every time I need to use the other set of programs. But I could live with this scenario: If I need to do more audio-intensive stuff, I'll just boot up to the audio partition and run the graphics programs in a VM, and then when I'm working heavily on the graphics part, I'll just boot the graphics partition as a regular OS directly on the hardware. Is this possible? For example by booting up a VHD as a regular hard drive? Or by setting up dual-boot, and every time the audio partition is shut down, synchronize the graphics VM VHD with the native graphics partition? Is it practical, given the above scenario? And if it's not possible, barring buying another computer, can anyone suggest a best-of-all-worlds setup (the two worlds being performance, sandboxing, and running in parallel) for the above scenario? Thanks in advance.

  Read the article

• Windows 8 Install Hanging at first white-font boot splash

  - by Omega

  I'm trying to install the Windows 8 preview on my Samsung Series 9 (2012, Ivy Bridge). I've done a bit of a custom scheme with this one: I'm using EFI/UEFI on this system. I've seen no indication that this system supports secure boot (yay!) My SSD is set up with GPT Ubuntu is already installed and working great via UEFI. I'm trying to boot the Windows 8 install from a USB stick via UEFI I don't have access to a CD drive. The problem is that the boot seems to hang at the very first splash screen that looks like this. White windows font, the little beads don't show up. My USB stick has an activity light and it does blink for the first few seconds, but then goes back to it's "nobody is talking to me" idle pulse. What I know: UEFI booting is definitely working. Windows 8 for those few seconds seems to have some kind of access to the USB drive. My Series 9 is running the latest BIOS/firmware. Any idea what I might be able to do to get Windows 8 installed??

  Read the article

• Virus cleanup; Windows Automatic Updates service crashes in esent.dll

  - by quack quixote

  Background I'm doing system recovery on an old WinXP SP1 system brought to me on suspicion of virus infection. After taking preliminary backups, I used MalwareBytes to detect and clean the infection. I might've even gotten it all. In the process, I've discovered (a) the system drive is showing signs of impending failure, and (b) the owner has been using the system's old crusty IE-6 instead of the up-to-date Firefox I've provided for him. So naturally, thinking I had a relatively stable system, I tried to hit the Windows Update site to install IE-8, in case further training doesn't stick. The update site told me it needed to update the installer, and I started that process. Soon after, wuauclt.exe started crashing, reporting addresses in module esent.dll. There's a Microsoft KB (910437) on a problem with that DLL, so I downloaded the hotfix and installed. The crashing did not stop. I attempted to install SP3 from the offline installer, but that didn't fix the issue either. The system is reporting a few hard drive / IDE controller errors, but they don't correlate to the crashes, so they aren't the direct cause. I've also attempted to rollback to the time between the infection removal and the first crashes, but that doesn't help. Question The hotfix I tried to install dealt with problem in transaction logs of the Extensible Storage Engine (ESE) database. I suspect this issue is similar, but that the database itself (whatever the ESE database is) is corrupted. Is there a way to clean or clear this database so that system operation returns to normal? Can someone enlighten me as to what the ESE database actually is, and where it resides? Can I just locate some files and delete them to bring this under control?

  Read the article

• Enterprise class storage best practices

  - by churnd

  One thing that has always perplexed me is storage best practices. Filesystems brag about how they can be petabytes or exabytes in size. Yet, I do not know many sysadmins who are willing to let a single volume grow over several terrabytes. I do know the primary reason behind this is how long it would take to rebuild the array should a drive fail. The more drives in a single LUN, the longer this takes and the greater your risk of losing another drive while the rebuild is taking place. Then there's usage reasons. Admins will carve out a LUN based on how much space they think needs to be allocated to the project. It seems more practical to me for the LUN to be one large array and to use quotas. I understand this wouldn't satisfy every requirement (iSCSI), but I see a lot of NAS systems (NFS) managed this way. I also understand that the underlying volumes can be grown/shrunk as needed quite easily, but wouldn't it be less "risky" to use quotas rather than manipulating volumes and bringing possible data loss into the equation? There may be some other reasons I'm missing, so please enlighten me. Can we not expect filesystems to ever be so large? Are we waiting for the hardware to get faster to cut down on rebuild times?

  Read the article

• VirtualBox how to merge arbitrary snapshot into base vdi

  - by jmathew

  I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID? Thanks

  Read the article

• Copying windows home server backup offsite

  - by Simon

  What ways are there to copy a windows home server backup to an offsite location? I'm talking specifically (and only) about the automated backup of my entire machine, and not the shared network folders. I am 90% working away from home on my laptop which has a 640GB drive so the shared folders are essentially useless to me. I backup every night, but if my house burns down or broken into the I'm in serious serious trouble ! I'm really looking for some alternative way to back up my entire machine - which much not interfere with the reliability or speed by which my WHS backs up my laptop every night. Either a way to 'export' a complete machine backup from the server, or recommendations on non-conflicting software I can backup to a 1TB drive at work are what I'm looking for. Note: I believe that WHS uses its own completely proprietary backup and doesn't use things like any 'backup bit' or 'archive bit'. I just dont want to install some other backup software that will conflict. PS I'm now running Windows 7 and just realized that I should probably check out the backup functionality it gives me. I assume that won't conflict right! Edit: Thanks for the hosted solutions. I'd also appreciate ways to backup to an 'offsite' location that I control - like my office vs. my home. The hosted solutions I think will be too slow or expensive for my needs.

  Read the article

• No boot device found. Press any key to continue

  - by Andrew Banks

  I took out the hard drive from my Dell Latitude E5420 notebook, put in an ADATA S599 solid state drive, and installed Ubuntu 11.10. When I boot, the Dell BIOS splash screen appears with a progress bar, which quickly fills up, and the screen goes black. All of this is like it was before. At this point, the OS splash screen should fade in. Instead, I was dismayed to see simply the following, in white text on a black screen: No boot device found. Press any key to continue After looking around for the Any key (just kidding) I press a key, and the Dell BIOS splash screen appears again with a progress bar, which quickly fills up, and the screen goes black. This time, however, the Ubuntu splash screen shows up, Ubuntu opens up, and all is normal. Every time I shut down, however, this happens again. It's like a game the computer and I play together. The computer has never started up without first saying: No boot device found. Press any key to continue and it has always started up after I press any key to continue. It also starts up fine if I click Restart instead of Shut Down. Thoughts?

  Read the article

• How to stop Firefox on an SSD from freezing when using the search box or submitting a form?

  - by sblair

  Firefox usually freezes for about a second whenever I search for something from the toolbar search box, when submitting a form, or when clearing the search box history. I suspect it has something to do with the auto-complete feature. Using Windows 7's Resource Monitor, the problem seems to be from the file: C:\Users\<username>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\formhistory.sqlite-journal I believe this is a temporary file which caches database writes. The following screenshot shows the very high response times from six different searches, and that the queue length on drive C shoots off the scale: My Firefox profile is on an Intel X25-M G2 SSD. The problem doesn't seem to occur if I create a new profile on a hard disk drive. However, I'd like to know why the problem exists on the SSD in the first place (because it's an annoying problem which contradicts the reason I bought an SSD, and it might happen with other applications too), and how to prevent it. It still occurs if Firefox is started in safe mode, and with the recent beta versions. Updates: VACUUMing the Firefox profile databases does not help with this problem. The SSD Optimizer in the Intel SSD Toolbox does not help either.

  Read the article

< Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >