Search Results

Search found 9088 results on 364 pages for 'after power failure'.

Page 292/364 | < Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >

• Converting An Older VMWare Image to ESXi

  - by Bart Silverstrim

  I have just installed VMWare ESXi and imported one physical machine without issue and one virtual machine, from an older version of VMWare Server on a Linux system, to it without issue. But I have another machine (Windows XP), virtual running on the VMWare Server, that I can't get the Converter to work with. Converter runs, says everything is fine, but when I go to the ESXi VSphere manager and hit the button to power up that vm, the console stays black with a blinking cursor and the processor for that VM spikes 100% and stays there. An event log item in VSphere warns something about activation issues with Windows. Has anyone else run into this issue before? Is it something with the disk controller? I copied the folder with the VM directly to the storage drive on ESXi hoping to create a new machine and point the data store to that folder or at least that drive image; nope, something about not using an IDE controller (must be something with the older format). In short, converter is doing something that particular machine doesn't like, and I can't find a way to simply open that hard disk image or convert it unless someone else has seen this. I try attaching a bootable CD image for disk repair to see if it can check the hard drive but I can't seem to get the console to boot from it...either too slow on the button or it just isn't able to easily boot from a virtual drive image (.iso). Any suggestions or help?

  Read the article

• No video signal and server shuts down

  - by Ilya

  I have a brand new server. The motherboard is Intel S2600CP4, two 8-core Intel E5-2600 processors. RAM is 8 DIMM slots of 8 GB each (KVR1600D3D4R11SK4/32GI, I installed them into the blue slots), Power supply is 1050W Corsair. Most of the time the server won't start up - the fans are spinning, but I don't have video signal. And it keeps restarting on its own every 3 mins. But maybe after 30 mins it will eventually load and show something on the screen. I even was able to install ESXi 5.0 (vSphere) on it. It recognizes both CPUs and all of the 64GB of RAM. But even then it worked only for around 5 hours and then restarted on its own. What's the problem? That's a very expensive peace of hardware and I can't afford purchasing a new motherboard/CPU. By the way, on the front panel the "System Status" LED is constantly amber (not blinking), even when the server started successfully. And also in the BIOS I can see lots of "processor 01 unable to apply microcode update 8160" fatal errors. Please help me with issue, I will really appreciate this!

  Read the article

• Computer resetting semi-randomly

  - by Peter

  Hi, I'm having a problem with my desktop whereby it sometimes resets itself semi-randomly. For example, I'll switch it on, it'll boot an OS and shortly after getting to the desktop it will immediately reset with no warning. The time isn't consistent - sometimes it does it before reaching login. I'm pretty sure it's not an OS thing; have tried Ubuntu and a Windows install and both exhibit it. It also doesn't appear to be heat-related because sometimes it appears to be able to "get past" it and will then run stably even under load; if anything it seems to be worse from a cold start. My gut feeling is some kind of power issue but I'm clutching at straws a little. Any suggestions on how I could go about testing it or trying to narrow the problem down would be appreciated. The machine is four years old now so while I can replace components if needed, it's not worth enough that I'm comfortable buying new parts without being pretty confident that they'll fix the problem. Thanks in advance for any help :) Edit: Okay, the motherboard is a MSI K8N SLI; CPU is an Athlon64 X2 4200+. Has one video card, a GeForce 7800GT. 1GB RAM, not sure of brand; 3 hard drives, two SATA and one PATA. Flashed motherboard to latest BIOS some time ago. Edit the Second: I thought I'd narrowed it down to the PSU for a while, but then it recurred again. I ended up pulling everything out but CPU, RAM and motherboard and it still seems to be stuffed (if anything, it's gotten worse in the last couple of days). I assume it's one of those three components, but the machine is old enough that I don't really want to spend money replacing any of them. So thanks for everyone's suggestions; much appreciated!

  Read the article

• If I partition a drive connected via eSata will it show different partitions when connected via USB?

  - by jeffreypriebe

  I have an odd problem with an external drive. I'm formatting it connected to my laptop prior to connecting it to my router. The HDD enclosure has both an eSata and USB connections. Generally, I connect it via eSata to my laptop. I created my partitions and connected it to the router, but I see partition information that is different than what I created. After chasing leads concerning large HDD size, I mindlessly connected the HDD to my laptop with USB. Lo! I see the same partitions as the router. Attached are screenshots using the same program and the HDD in question. The only difference is the connection. For the first, I connected via eSata and hit "refresh" on the partition program. Then, turned off the HDD, disconnected the eSata cable, and connected via USB. Power and refresh. eSata: reports a total HDD size of 2328 GB, with four partitions (the third being 1.96TB) USB: reports a total HDD size of 280 GB, with three partitions (the third being 279 GB) Any idea why this is happening? It looks like it clearly is an issue of the 4K sector size and not playing nice with the USB enclosure. I tried it eSata and USB in Windows and Linux and it appears consistently that eSata is reporting correctly, USB incorrectly.

  Read the article

• How to choose the most optimal RAID settings on PE2950

  - by javano

  I have some Dell PowerEdge 2950's with 4x 15k, 150GB Cheetah SAS drives in them. They are going to be VM hosts, CentOS running ESXi with Windows Server 2k8 guests. Some guests will be hosting IIS servers, and others MSSQL servers. I am trying to set the RAID virtual disks settings and can't decide which is more optimal given this situation; Read Policy: Out of Read-Ahead, No-Read-Ahead and Adaptive Read-Ahead, the default is Read-Ahead. I will be making large sequential writes initially, writing out blank images for virtual machine hard drives (lets say 30GBs from /dev/zero for example) so Read-Ahead seems good at first. But within the virtual machines reads could be random from anywhere within their file systems as they are IIS and MSSQL servers, so perhaps No-Read-Ahead is a better idea? Now I think Adaptive Read-Ahead would be better then as a compromise but I don't know much about this option, how does it compare in performance to the others? Write Policy: write-back caching, write-through caching, the default is write-back caching. The default of write-back caching is safer than write-through caching but at a performance expense. My thinking here is that in the event of power loss for example, it seems more likely in my head (this is why I need some clarification!) that damage will occur to a guest VM with write-back caching enabled, so I should favour write-through? I have searched around and there is obviously no definitive answer, so I would like to find out what is best for my situation.

  Read the article

• Laptop shuts down randomly without warning

  - by Robert P.

  My Asus Zenbook UX32V turns off randomly when I'm working on it. This happens both when the computer is recently turned on (5 minutes), and after being on for several days. I'm not running any heavy software The laptop is not heating The fan is not working on the maximum capacity (it's not heating) It happens when the laptop is lying still on the table It is no warning, it simply goes black It happens both when charging and on battery My guess is that it suddenly lose power somehow. What puzzles me is that I can flip the laptop upside down, sideways, shake it, etc. without it shutting off. This makes me think it's not something that's loose causing occasional short-circuits. I realize that the laptop probably doesn't like flipping and shaking, but it was the best way I could troubleshoot. I rarely turn the computer off, only have it in hibernate or sleep mode (most often hibernate). I've never experienced that the laptop is off when I wake it up from sleep mode. I've had the problem for a few months and it happens 2-8 times a week. Specs: Asus Zenbook UX32V Windows 8.1 (it happened in Windows 8.0 too) Intel i5-3317U CPU @ 1.70GHz The laptop is approx 1.5 years, but it has a small dent on one of the sides that probably voids the warranty. The dent has been there since week one and I don't think it's related to the problems I'm having now. Does anyone have a clue what might cause this, and how it might be fixed? I've read all other questions (some of which are listed below) that seem related to my issue, but none report the same behavior as I'm experiencing. Most report heavy games, heating etc. Asus N53J Laptop randomly shuts down Laptop is randomly shutting off Computer shuts down without warning My laptop acer aspire 5720 suddenly turn off randomly Computer randomly shutting down Windows 8.1 randomly shuts self down ASUS K55VM Laptop unexpectedly shuts down

  Read the article

• Looking for an application to record audio and video on a linux "embedded" device

  - by Luke404

  I am working with a linux x86 device with limited CPU resources (as a prototype we just use a pentium-m netbook). We'd like to record video from one V4L2 device (we'll probably end up using just USB Video Class devices like all modern webcams) and one audio stream from an ALSA source. The thing will not have screen and keyboard, and obviously no X11 environment. Goals are: do as little work as possible to cope with little cpu resources - for example I'd like to record video in the native MJPEG I get out of the UVC devices encoding audio to MPEG3 Layer-2 (aka mp2) is ok since it let us save a lot of space (compared to raw pcm samples) and does use little cpu power I don't mind loosing some video frames here and there (UVC devices do that) as long as I can get audio and video streams syncronized not require user input to start the thing (a python script takes care of initialization, startup, shutdown, etc...) be able to open the resulting files for postprocessing without too much effort (ie, if mplayer or vlc can play it, it's fine) So far the only app I found that could be started from command line and record V4L2 video + ALSA audio is mencoder but I'm having some difficulties with it. It should be able to do that but I cannot record audio and video together - just one of the two. And if I use two different processes to record to two different files I have no means to get them in sync (audio is more or less always correct, but video framerate will vary over time and it seems to lack timestamps to correctly play it back to the correct time). Long story short, how do you record an unconverted MJPEG stream (from an UVC device) and an audio stream (from an ALSA device, possibly encoding to any standard format) using a command line tool, to a single file (MPEG or any other container), keeping audio and video in sync?

  Read the article

• TV won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• Laptop Acer Travelmate 4050 takes over 10 Mins to POST

  - by Belliez

  Hi, I am a computer tech and have received a laptop for repair. I noticed when I turned it on the laptop would not do anything for a min or two (the fan would run up and stop, power led would shine and some cd rom activity then stop). It would sit there with a black screen. Suddenly after a random number of minutes (between 1-20mins!) the Acer BIOS screen would display and POST would happen before booting into Windows XP. It has frozen in XP at various times and pointed towards a CPU fault and over heating. The fan was on its last legs, sounded like a car engine, so I replaced this. Still same issues. I next replaced the CPU like for like. Same problems. Also applied new thermal paste between the cpu and heatsink, when running the fan kicks in occasionally (not as often as I thought it would) and I left it playing mp3, online radio and updating to service pack 3 and it wouldnt freeze. shutting down ok, cold start, not ok. Waits again before showing the BIOS screen. The hard disk was also making a screaming noise (SMART test and chkdsk passed) but I also replaced this. The laptop powers up with and without the battery so dont think its a battery issue. Running out of ideas and wondered if anyone had any advice. Thanks

  Read the article

• Trouble with HP printer

  - by reyjavikvi

  I have a HP Photosmart C3180 (it's a printer/scanner). For some reason, it recently stopped working. The power light is blinking (I think all the other lights are one, but don't remember, I'm not there right now), and the only way to turn it off is to unplug it. It won't print anything, and when you put a page in the tray it sucks it in without printing anything on it and stops when the paper is on its way out (Again, I don't remember how we managed to get it out, sorry). This printer is hooked up to a computer running XP, but it doesn't work either when printing from the network. Weirdly, the scanner works fine. Do you have any ideas on what could be the problem? Could it be a driver problem? By the way, sorry if the question lacks a bit of detail. I don't know much about printers, and I don't have it here so I can't remember exactly all the details. If needed I can update the question tonight or tomorrow.

  Read the article

• Wastage of resources in Virtualization

  - by Sabeen Malik

  I have asked this question on SO, but was suggested that i ask it here on SF, so here it goes. http://stackoverflow.com/questions/3010753/wastage-of-resources-in-virtualization I am not sure if this is the right place to ask the question. However i hope it is. When looking for a VPS earlier today, I was trying to understand how each container would work in the background. Keeping in mind the fact that the operating system uses most of the memory and power on a system, wouldn't having multiple operating systems in the same machine mean more wastage of resources. For instance if i was running centOS on a dedicated box and it was running lets say 20 background OS level processes. Then i go and install a virtualization platform and install 5 more centOS virtual machines in the same system which are exactly the same as the host operating system. Doesn't this mean duplication of those 20 processes 6 times? So internally the context switching is happening between 120 processes instead of 20? Further Notes: Here is an example of what i am thinking: I have a master-slave configuration for a long running, cpu + memory intensive process, which can be distributed to 4 machines. Lets say when the process runs on these 4 machines with lets say 1 Gh CPU and 1 Gig RAM, i get 400 results per hour from the cluster (assuming 100 results from one machine) . Now i get a bigger machine ( lets say 4Gh and 4 Gig RAM), have 4 virtual hosts on it with 1 Gz CPU and 1 Gig RAM. Will this configuration give me the same 4 results per hour from these 4 virtual hosts?

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• System freezes during boot process

  - by slugster

  Hi everyone, i have a machine running Win7 Ultimate. It was running fine, then it just froze - all the stuff i was doing was still on the screen, but mouse and keyboard input was ignored, any animation that was happening on the screen stopped, the machine literally just froze. So i rebooted (power off button), from then on the machine will reboot, but it ultimately freezes again. The instance when this happens will vary - i have made it as far as the Windows login screen, but mostly it will do the POST, then give me the option to press F1 to continue or Del to enter BIOS settings (but of course pressing a key has no effect - it's frozen!). I have disconnected everything not necessary for the boot process, the only peripheral that remains attached is the keyboard. (even the network cable is disconnected). Prior to this the machine was operating fine. The install of Win7 is only 2 days old, and it was a fresh reinstall (i.e. not an upgrade or repair). Can anyone give me an indication of what may be wrong here? I'm not sure if this question should be here or on SuperUser, please migrate it if i have chosen the wrong board.

  Read the article

• Recover data from physically damaged harddrive. What are my options?

  - by Michael Kniskern

  I was trying to replace the power supply in my desktop PC and ended up physically damaging the data connection from the hard drive to the motherboard. The plastic shelf for the copper prongs on the hard drive broke into the cable. Here is a picture of my handy work: I went to Best Buy Geek Squad to discuss my options and they said that they will need to send it to the recover center it could cost anywhere between $250 to $1600 USD to recover the data out the hard drive Is this reasonable for data recovery from a physically damaged hard drive? Are there any other options I can explore? I am going to talk to the data doctors to see what my options are. Update I took the HD to Data Doctors, and they told me that the SATA connection was broken to they would need to replaced the data connector and then copy the data to a brand new hard drive. So, with the initial analysis, cost of replacement parts, and data recovery fee it came out to $865.00 USD. The technician specifically stated if this was an older hard drive that would just need to replace the data connector. But because there is specific information related to the individual hard drive in the flash ROM, they need to transfer the data to a brand new hard drive.

  Read the article

• Dell Studio 1555 not starting up

  - by Abhishek

  This is a 3-year-old laptop. I never had a big problem with it until now. I updated Kubuntu the night before yesterday. And Firefox got updated to version 18 and a few other related packages got updated. Then I shut down the laptop and restarted it, but it failed to start. I could hear the fan and the hard disk and the optical disk drive initialize. And the power button also lighted up. But there was no video - no POST or BIOS menu. I even opened the laptop up to the point when only the motherboard was the only thing attached to the base cover. I took it to the technician this evening. He checked it casually, and said that it might be a motherboard problem and will cost quite a bit to fix. Though he was not sure and said that he will give me a call after confirming the problem. Has anyone else had the same problem? What was it and what was the fix?

  Read the article

• Computer won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• System freezes during boot process

  - by slugster

  Hi everyone, i have a machine running Win7 Ultimate. It was running fine, then it just froze - all the stuff i was doing was still on the screen, but mouse and keyboard input was ignored, any animation that was happening on the screen stopped, the machine literally just froze. So i rebooted (power off button), from then on the machine will reboot, but it ultimately freezes again. The instance when this happens will vary - i have made it as far as the Windows login screen, but mostly it will do the POST, then give me the option to press F1 to continue or Del to enter BIOS settings (but of course pressing a key has no effect - it's frozen!). I have disconnected everything not necessary for the boot process, the only peripheral that remains attached is the keyboard. (even the network cable is disconnected). Prior to this the machine was operating fine. The install of Win7 is only 2 days old, and it was a fresh reinstall (i.e. not an upgrade or repair). Can anyone give me an indication of what may be wrong here? I'm not sure if this question should be here or on SuperUser, please migrate it if i have chosen the wrong board.

  Read the article

• Hard drive spark, can it be recovered?

  - by user163558

  Alright, so I was going to install Source Film Maker but I didn't have any space, so I decided to connect an HDD via an USB converter(image below). I shut down the machine, turned the PSU off, and connected via a Molex connector & the USB converter. I turned back on the PSU, no sparks or anything, everything normal, but when I turned on the machine, I heard some sizzing(lol?) and sparks flying and a little flame, but the PC was running fine. I pressed the power button instead pulling out the plug (I panicked) so it continued to short circuit for about 10 seconds. There's a very little part on the HDD that become ash, it's near the Molex connector and the circuit is a little black as well. I'm afraid that I will damage the HDD more so I didn't hook up the HDD after all. Do you think it's the PSU(came default with Cooler Master Elite 430, 500W) or it's the HDD(Samsung SP1203N)? P.S: I've attached the HDD same way before(like 3 months ago), and it worked. HDD burn: USB connector: Sorry for the bad image quality, taken with my phone.

  Read the article

• Webapp in Jetty can't find properties file after running a couple days

  - by Cuga

  I have a webapp running in Jetty on Mac OS 10.6. After a few days of it running and without the server losing power or rebooting, it seems to stop working saying it can't find a properties file. This properties file is included inside the .war file deployed to the /webapps directory. If I restart Jetty as the superuser the web service works again just fine. Can anyone lend any advice to what's going on and how I can fix it? The error being shown when it isn't working is: Problem accessing /my-web-service. Reason: INTERNAL_SERVER_ERROR Caused by: java.lang.NullPointerException at com.company.service.Dao.readFromPropertiesFile(BwDao.java:35) at com.company.service.ServletHandler.doGet(ProxyClass.java:66) ... at org.mortbay.jetty.HttpConnection.handle(HttpConnection.java:404) at org.mortbay.io.nio.SelectChannelEndPoint.run(SelectChannelEndPoint.java:410) at org.mortbay.thread.QueuedThreadPool$PoolThread.run(QueuedThreadPool.java:582) Here's where the properties files exist that it's trying to read from the .war file: And this is how the properties are being read from the classpath: Properties properties = new Properties(); properties.load(Thread.currentThread().getContextClassLoader().getResourceAsStream( "app.properties")); Again, this does work just fine if I have just restarted the server, but it seems to fail after running a few days.

  Read the article

• Lenovo S10 Ideapad will not boot while original hard drive is installed, neither from hard drive or

  - by aki

  Hello, first time posting here so I'll try to be very clear. I have a Lenovo S10 Ideapad netbook which fails to boot to an OS. It shows the Lenovo splash screen and can get to the BIOS but it doesn't get to GRUB (was dual booting Ubuntu 9.10 and Win 7, was working fine for months, ie this isn't a new dual boot gone bad). After the splash screen it displays a flashing cursor in the upper left corner. Power cycled to no avail. Here is what I have done trying to narrow the problem down: The machine will boot to Ubuntu using an install/live USB drive, but only if ANOTHER hard drive is installed or NO hard drive is installed. The boot order always lists USB first. Also, there is a 2 gb RAM upgrade but I think that's fine; the Ubuntu USB drive boots fine with it, and "free" sees the whole 2gb of memory. So it seems like the hard drive is bad. I was able to put the bad drive in a different laptop and mount it to recover files. I'm ready to replace the bad hard drive, but I would like to know if this situation makes any sense. If the hard drive is bad, shouldn't I still be able to boot with the Ubuntu USB drive while the bad drive is installed? I would have expected the machine to boot into Ubuntu anyway even if with a bad drive, since the boot order lists USB first. But it seems that when the bad drive is installed, the machine ignores the USB drive and hangs with the flashing cursor. Thanks for any ideas! Sorry for the long post, I just want to put all the info I have up front! Basically I'm going to buy a new drive, but I am mostly curious if this is a typical or at least not unusual situation.

  Read the article

• USB Device Not Recognized

  - by Franky Chanyau

  Ok this one gets a little bit complicated but bare with me :D A client brought her computer in to be fixed about a week ago, she says she tried charging a new phone she bought from china and immediately after her usb keyboard and mouse stopped working (typical). I had a quick look at it but because I did not have time, I did a simple system restore and it seemed as if the issue was fixed. I promptly sent it back to her but a few days back she called saying that the issue has returned. Turns out the computer was riddled with some virus that also corrupted her XP install so I had to format the whole thing(yes I tried repairing). I hoped that the format would fix the keyboard and mouse issue but the whole thing has escalated and the computer will throw the "USB Device not recognized" error when I plug anything into the many usb ports it has. I have installed all the drivers (including the chip set drivers) for the pc and even tried the unplugging from the power for a while trick, still no luck. I am sure it is not a hardware issue, but may be wrong. This is way over my head. Can anyone help? Computer: HP Compaq DC7100, Intel Pentium 4, 512mb RAM OS: Windows XP Professional SP2

  Read the article

• Using my old PC as a web/file server?

  - by Garrett

  I have an old desktop computer that I've been trying to sell for AGES. I guess nobody is looking for computers because it was advertised at a dirt cheap price on craigslist, local papers, etc. Anyways, I was wondering if it would be worth it to set it up as a home file server, a web dev server (I have a web host for actual production use), and maybe host a few server applications (ex: ventrillo). The computer is actually an old Dell that I cannibalized after the motherboard being destroyed by lightning, so it has fairly new parts in it. The specs are: P4 3.4GHz w/ HT and Artic Cooling Freezer 7 3GB DDR2 533 RAM 80GB hdd (will upgrade the hard drive if it's even worth using as a server) basic dvd rom 430 Watt Thermaltake PSU (it might be important to note that it is only 60% efficiency) ATI Radeon x600 256MB Antec 300 case It's not a really beefy machine, I just can't see giving it away or putting it in the corner to just collect dust. I have Windows Server 2008 R2 Standard and I am confident in my skills in operating most Linux operating systems. I'd also be using it to tinker with when I learn new things in my server admin classes (I'm finishing my 2nd year in college at the moment so I'm still learning) Also, my house is quite old and the electrical wiring is pretty poor (it MIGHT be up to code, then again, where I live most people don't even know what regulations are or let alone know how to spell it...) Would it be safe to leave it running all day and is it going to run up my electric bill because of the PSU efficiency? I only have 5mbit cable internet, but I won't be running very bandwidth intense services on it so it should be ok. I should elaborate on why I am concerned about the power. The circuits should be fine, but I'm more concerned about fire hazard. What is the likelihood that the server could cause an electrical fire? Again, thank you all for the feedback!

  Read the article

• Finding useful crash-information in Windows 8 Consumer Preview

  - by Lukas Knuth

  I'm currently diving into C# and wanted to play around with the new Metro-styled-applications introduced with Windows 8, so I updated my Windows 7 to Windows 8 Consumer Preview. The problem I'm facing right now is, that the system freezes after 3-5 minutes. It does not take any input from the keyboard or mouse and it does not recover (at least not in less then 10 minutes). Since I have a background in Linux, I'd like to find some information about the cause of the freeze, but I have no idea where to search. I checked the system-logs (under "System Control" - "Management") but they only record that the system was shut down unexpectedly (doe to the face that I held down the power-button to reboot the PC). There is no useful crash-information in there. I don't want to spend hours on randomly reinstalling drivers and doing things that "might help". Isn't there any place I can find some useful information about the freeze? Before you ask: I installed Windows 8 as an updated on my old Windows 7 installation (which worked fine by the way). My hardware fits the minimum requirements (specs can be found here, the MacMini 3,1 model with 2GHz processor). I have updated the graphics-card drivers to the newest Windows 8 drivers from nVidia.

  Read the article

• How to troubleshoot when one has no idea where to start?

  - by Chris Walton

  I am looking for hints, tips and answers on how to get started on troubleshooting when: The problem is intermittent The problem could lie literally anywhere - operating system; free source software; my own software developments; purchased software; crumbs on the keyboard; the specific combination of software I am currently running; Maxwell's demon; the little blue men actually running the machine have gone on strike; etc. I have expertise only in a few of the areas that are potential candidates for the cause of the problem. The specific problem I am having is detailed below as an example, but I am not seeking answers to my current problem, but rather where and how to start on tackling such problems. I am currently encountering a problem with my new machine. On a few occasions the machine has just frozen; not accepting keystrokes, mouseclicks, or anything except the power on/off switch. Invariably I have been merely browsing the web; I have had a few (<= 6 other applications) running. None of these applications are major; and represent a mix of commercial programs and open source programs, typically migrated from Unix of some variety. My machine is a Windows 7 I7 quad core laptop.

  Read the article

• Exchange 2010 DAG + VMWare HA = no support?

  - by Dan

  We currently have an Exchange 2003 clustered environment (two machine cluster) that we're looking to upgrade to 2010. We recently purchased a VMWare virtualization environment (three Dell R710's with an EMC NS-120 serving up NFS datastores - iSCSI is available) that we wish to use for this new environment. I'm seeing that Microsoft does not support Exchange 2010 DAGs with a virtualization high availability solution (see links below). I would like to utilize the DAG to ensure the data stays available if one host goes down, and HA to ensure that if the physical host goes down, the VM will come back up on the other available host. Does anybody know why MS does not support this? VMWare HA will only restart the VM if it is hung/down - I don't see any difference between this and restarting the physical box if someone pulled the power... Will we only run into issues with support if it has something to do with HA/DAG failover or will they see we have HA and tell us to put it on a physical box even if it has nothing to do with HA? If we disable HA for these VM's will that satisfy them on a support case? Has anybody set up an Exchange 2010 DAG on VMware with HA enabled? Will they have any issues with using an NFS datastore? We have much greater flexibility on the EMC with NFS vs iSCSI, so I would prefer to continue utilizing that. Thanks for any input! http://www.vmwareinfo.com/2010/01/verifying-microsoft-exchange-2010.html Take a look at the second image under "Not Supported" http://technet.microsoft.com/en-us/library/aa996719.aspx "Microsoft doesn't support combining Exchange high availability solutions (database availability groups (DAGs)) with hypervisor-based clustering, high availability, or migration solutions. DAGs are supported in hardware virtualization environments provided that the virtualization environment doesn't employ clustered root servers."

  Read the article

< Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >