Search Results

Search found 9286 results on 372 pages for 'transfer speed'.

Page 296/372 | < Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >

• Network switches for LAN party

  - by guywhoneedsahand

  I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• VPN sharing on Mac OS X 10.5 machine

  - by Jens

  I have a rather weird problem. I want to share a VPN connection that has been established by my Mac OS X 10.5 computer with another machine in my network. This is what I did: In the /etc/hostcongig file on the main computer I added the line: IPFORWARDING=-YES- I assigned a fixed IP address to my computer (192.168.178.30), a fixed one to the other machine (192.168.178.60) and my computer's IP address as gateway on the other machine. I connected to my VPN using the internal Mac OS X VPN client (PPTP connection) I run this script: #!/bin/sh natd -same_ports -use_sockets -unregistered_only -dynamic -interface ppp0 -clamp_mss ipfw -f flush ipfw add divert natd ip from any to any via ppp0 ipfw add pass all from any to any sysctl -w net.inet.ip.forwarding=1 Source: Using (and sharing) a VPN connection on your Mac Now everthing works smootly, however speed is an issue. I get 1,8 MBit/s on my main machine and only 0,3 - 0,6 MBit/s on the other one. My question: What could possibly be wrong? Do I have to tweak MTU settings, is there any packet inspection ongoing that needs time....? Any help appreciated!

  Read the article

• How to define nodes from a Hiera file in Puppet?

  - by Pigueiras

  I am using puppet and the puppet network device management module and I am trying to build my custom type. In the built-in type for the routers configuration, you can specify a list of nodes and then the configuration inside that node: node "c2950.domain.com" { Interface { duplex => auto, speed => auto } interface { "FastEthernet 0/1": description => "--> to end-user workstation", mode => access, native_vlan => 1000 # [...] More configuration } What I am trying to do, is to move the manifest declaration of the nodes and the configuration of my custom type to a Hiera file like this one: nodes: - node1 - node2 config_device: node1: custom_parameter: "whatever1" node2: custom_parameter: "whatever2" And then in the manifest iterate over the hiera file creating the nodes with the configuration of each node with something like (I am taking as reference this question in serverfault): class my_class { $nodes = hiera_array('nodes') define hash_extract() { $conf_hash = hiera_hash("config_device") $custom_paramter = $conf_hash[$name] ## TRICK lies in $name variable node $name { my_custom_device { $name: custom_parameter => $device_conf['custom_parameter'] } } } hash_extract{$pdu_names: } } } But for this solution I have two problems, I can not define a node inside a define and I can not parameterize a node name. So, is there any way to declare nodes from a Hiera file with their configuration inside?

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• Troubleshooting my internet connection

  - by Simon Verbeke

  While I was out of the house, my father rearranged the network cables a bit. I don't know what he has done exactly - He says nothing more then pulling and untangling. When I came back home, my internet connection changed its IP from 192.168.0.205 to 169.254.197.233. The speed changed from 1Gbps to 10Mbps. It has also been at 100Mbps for a while. My subnetmask changed from 255.255.255.0 to 255.255.0.0. The standard gateway changed from 192.168.0.1 to no standard gateway. My DNS servers remain the same. I have checked the lights of the UTP ports, and it looks like it's only sending a heartbeat every few seconds. A sketch of the (relevant part of) the network: My PC ----- extender ----- modem ^ ^ ^ Wired | Wired | This thing connects two cables to each other All the cabling is gigabit, my network card is a Realtek RTL8168C(P)/8111(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20). THe modem is a CBN SVG6540E I have no idea what is going on here and I don't know how to find out either. Any help is welcome! If you need any more info, please ask.

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• Why does GIMP start up so slow on my machine?

  - by muntoo

  EDIT 2: One way would be to disable script-fu. Does anyone know how to disable it at startup? Is it possible? Would GIMP still work? What wouldn't work? Could I start it later, after loading? Is there any way to speed up GIMP's startup time on Windows Vista Home Premium 32-Bit 1.6 [Dual] Intel Processors? On XP [different computer], it loads in less than 3 seconds. On Vista, it takes 20 seconds: 2 Seconds (other - fonts, brushes, etc) 18 Seconds (extension-script-fu) It just freezes at extension-script-fu. Looking at Process Explorer, I see that it's not taking any CPU at all. EDIT 1: It does seem to be taking 50% of the CPU. It gets stuck for about 18 seconds, and then starts working again. Then, the actual GIMP program pops up [...finally]. I have the latest stable version running (I think). I tried it with XP SP2 Compatibiliy mode and/or Run As Administrator, but that didn't help.

  Read the article

• Netgear CG3000D new Modem/Router - Random High Ping

  - by justin.chmura

  Cox just recently came out and looked at my internet and decided that the modem I had was causing high latency issue. The speed was fine but the ping would spike to around 100 and over when gaming or putting a load more than browsing on the line. After they replaced it, it seems like I get better latency, but when it spikes, I get upwards of over 300 ping with like 500 jitter. I figured I would hit the serverfault universe before sending another email to Cox. I opted not to do the Cox setup as it was an extra $20 which I thought would have just setup the wireless (which I can handle). Is it a setting or something that I missed that needs to be setup? The firmware for the CG3000D is awful and not fun to use. I did change some hidden settings on the RgServices.asp page (I'll attach a screenshot). I've also heard that the Router/Modem combos are awful and that I should go back and just ask for a modem stand-alone. Any input is helpful. All screenshots: http://imgur.com/a/JX6qu#0

  Read the article

• why would resetting the Netgear N300 router fix my Win 7 laptop's slow wifi?

  - by rjnagle

  In the past day the wifi download speeds of my Win 7 HP 64 bit laptop have slowed considerably. I am trying to troubleshoot the problem and to figure out whether it's hardware related (i.e., is the Intel(R) Centrino(R) Wireless-N 2230 the problem?) or router related. I have a Netgear N300 router connected to my modem. I'm using Speedtest to measure my speed. First, during my problem state, my ipad can download and upload at normal speeds. It's only my Win 7 laptop which is having problems. Because my ipad downloads at normal speeds, that would tell me that the problem is specific to the laptop (either HW or SW). But when I restarted my Netgear router, the laptop wifi problems disappeared. That just doesn't make sense. If we know that one device can connect properly to the router, why would a laptop have problems? What are some possible reasons why this might happen? Also, during my problem state, I noticed that on my laptop upload speeds were faster than my download speeds. Anybody have a guess about what might cause upload speeds on one device to be faster than another? Is there any actions i could take (or options to enable) so this problem won't occur. (I initially thought my problem might be software related or memory related -- Norton AV or browser plugins. But even after I disabled everything and made sure memory footprint was minimal, the slowdown was still occurring -- and it solved itself altogether when the router was reset).

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• Is there an objective way to measure slowness of PC/WINDOWS?

  - by ekms

  We've a lot of users that usually complain about that his PC is "slow". (we use win XP). We usually check startup programs, virus, fragmentation, disk health and common problems that causes slowness (Symantec AV drops disk to 1mb/s , or a seagate HD firmware error in certain models), but in those cases the slowness is pretty evident. In other hand, the most common is the user complaining about his pc but for us looks OK, even in 6 years old desktops. People sometimes even complains about his new quad core desktops speed!!! So, we are asking if there's a way to OBJECTIVELY check that a computer didn't dropped its performance, compared with similar ones o previous measures, specially for work use (I don't think that 3dmark benchmark o similar may help). The only thing that I found that was useful is HDTune, but it only check hard disk performance. Basically, what we want is something that enable us to say to our users "see? your PC is as slow as was three years ago! stop complaining! Is all in your head!"

  Read the article

• Why am I experiencing random connection timeouts? (CentOS)

  - by Ryan

  I have a CentOS server setup that currently hosts several websites (all relative of each other in some form or another). As of recently throughout the day at the most random times the website speed will lag to a crawl and eventually hit a connection timeout. When I say random times this typically happens anywhere between 10am and 1pm usually, however, this morning this happened to me at 8am. I do not have a lot of familiarity with server knowledge as far as what I am looking for in this situation. What are some possible causes of why my server is slowing the websites down to a complete crawl or timing out? Are there specific things I should be checking for when this happens? I have noticed using: tail /var/log/httpd/access_log That usually when this down time occurs there are lot of IP addresses related to BingBot, Googlebot, and sometimes various bots or spiders that I am unfamiliar with. Could this be related and if so how can I avoid this from causing my websites to lag out? Thanks in advance for any help or advice. The websites that are timing out are built with PHP and use a MySQL database to display information.

  Read the article

• Is it a good Idea to switch to a SSD to use less battery?

  - by Walter Maier-Murdnelch

  I am thinking of buying a SSD for my laptop, mainly for the purpose of extended operating time when running on battery. At the moment I use a Hitachi HTS545032B9A300 (320GB) (Datasheet) as main drive and a Seagate Momentus 5400.3 120GB as secondary drive. I dualboot Windows and Linux but I don't need the windows partition any longer, a 120GB SDD would be more than sufficient space-wise. Speed is not an issue for me, I make heavy use of tmpfs (ramdrive) within Linux and transfers of bigger files are mainly through some network filesystem anyways, thus a cheaper SSD should do. For the purpose of comparison I chose the OCZ Vertex Plus 120GB. Power consumption always is a big promotional thing the industry uses to make me want to buy their SSDs, some sheet on the OCZ page provides an astonishing comparison of desktop HDDS and SSDs. The numbers I got comparing my laptop HDD and their SSD were not really astonishing any longer. Hitachi 320GB HDD: Startup (W, peak, max.) 4.5 Seek (W, avg.) 1.7 Read / Write (W, avg.) 1.4 Performance idle (W, avg.) 1.3 Active idle (W, avg.) 0.8 Low power idle (W, avg.) 0.5 Standby (W, avg.) 0.2 Sleep 0.1 OCZ 120GB SSD: 1.5W active 0.3W standby I see that there are differences, but actually they don't seem that high as I though they were. And compared to the power consuption of the rest of my system I wonder if it makes a difference at all. Have I just taken the wrong look at the whole thing or may I be better off to buy another battery for my laptop?

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• Serving images from another hostname vs Apache overload for the rewrites

  - by luison

  We are trying to improve further the speed of some sites with older HTML in order as well to obtain better SEO results. We have now applied some minify measures, combined html, css etc. We use a small virtualized infrastructure and we've always wanted to use a light + standar http server configuration so the first one can serve images and static contents vs the other one php, rewrites, etc. We can easily do that now with a VM using the same files and conf of vhosts (bind mounts) on apache but with hardly any modules loaded. This means the light httpd will have smaller fingerprint that would allow us to serve more and quicker, have more minSpareServer running, etc. So, as browsers benefit from loading static content from different hostnames as well, we've thought about building a rewrite rule on our main server (main.com) to "redirect" all images and css *.jpg, *.gif, *.css etc to the same at say cdn.main.com thus the browser being able to have more connections. The question is, assuming we have a very complex rewrite ruleset already (we manually manipulate many old URLs for SEO) will it be worth? I mean will the additional load of main's apache to have to redirect main.com/image.jpg (I understand we'll have to do a 301) to cdn.main.com/image.jpg + then cdn.main.com having to serve it, be larger than the gain we would be archiving on the browser? Could the excess of 301s of all images on a page be penalized by google? How do large companies work this out, does the original code already include images linked from the cdn with absolute paths?

  Read the article

• Recover badly recorded DVDs

  - by CesarGon

  A few years ago (2003-2005) I bought a Sony USB external DVD recorder for my Dell laptop and I used it to burn a lot of discs. Much later, when I tried to use one of these discs, I realised that I could not read it. The disc behaved as if it was scratched or dirty. I tried on a couple of different DVD drives but got the same effect. Sadly, all the discs that I burnt with that recorder suffer from the same problem. Edit. When I read one of these discs with ImgBurn, I get lots of unrecovered read errors in multiple sectors, even at 1x speed. The sectors that cause read errors seem to be quite random; it's not always the same one. I have no idea what could be wrong with the discs. I doubt that they are scratched or dirty; it would be too much of a coincidence that all the discs that I burnt with that recorder got damaged at the same time. Also, they don't show any physical defects. Is there any way to diagnose what the problem is and, hopefully, recover the contents of the discs? Many thanks.

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Matched or unmatched drives for RAID arrays?

  - by Will

  Looking around there is conflciting information on this, with some strongly suggesting one or the other. From my understanding the issue with matched drives is that the wear on both drives is more or less the same, so the potential for the second drive failing with or very soon after the first is pretty high. People also claim matched drives give substianatally higher performance however assuming the unmatched drives are more or less the same (eg 2, 1 TB STATA II 7200rpm drives with 32MB cache), would the minor differences between say a Seagate and a Western Digital one (say one has a 128MB/s read rate, and the other a 150MB/s read rate, as well as I guess various other minor differences) actually cause any notable performance loss, ie potentialy worse than two matched 128MB/s drives, or does RAID not really care and give you essentially an optimal solution (eg upto 278MB/s total read speed for RAID 0 and 1) and similar for other RAID with more "unmatched" drives (5 and 1+0 come to mind as possibilities)? Also I couldnt find much info on how this is different on different RAID setups, eg RAID 0 or RAID 1, software or hardware RAID, etc. I'm assuming such things have an effect, and thats it's not all the same for RAID in general?

  Read the article

• VPS goes slow at more than 20 users online at the same time

  - by hachiari

  I have 512 MB VPS (brustable to 1GB) Somehow, the site goes slow when there are about 10 users, and becomes impossible to load at 20 users online at the same time. I wonder what could be the problem for this. The bandwidth connection of the VPS is 1Gbps. Here is some settings in my VPS: KeepAlive Off <IfModule prefork.c> StartServers 7 MinSpareServers 7 MaxSpareServers 10 ServerLimit 64 MaxClients 64 MaxRequestsPerChild 0 </IfModule> my.cnf settings - calculated Max Memory 300MB Output from UNIXBENCH INDEX VALUES TEST BASELINE RESULT INDEX Dhrystone 2 using register variables 376783.7 13429727.4 356.4 Double-Precision Whetstone 83.1 1137.5 136.9 Execl Throughput 188.3 1637.4 87.0 File Copy 1024 bufsize 2000 maxblocks 2672.0 148868.0 557.1 File Copy 256 bufsize 500 maxblocks 1077.0 79430.0 737.5 File Read 4096 bufsize 8000 maxblocks 15382.0 1410009.0 916.7 Pipe Throughput 111814.6 4419722.0 395.3 Pipe-based Context Switching 15448.6 561505.1 363.5 Process Creation 569.3 10272.7 180.4 Shell Scripts (8 concurrent) 44.8 514.3 114.8 System Call Overhead 114433.5 3537373.8 309.1 ========= FINAL SCORE 295.0 I am afraid that the VPS company limit the number of connection to the VPS... is it possible? The server is in Japan, but the site has global traffic (some of the traffic are from countries with low speed connection). Could this be the problem? This is a serious problem :( my site just cant grow if this keeps on happening... please tell me if you have any idea. Thank You, Bryant

  Read the article

• Cannot install windows. Compaq Presario CQ62

  - by Matthew

  I bought a used Compaq Presario CQ62 for cheap, and went to install windows on it. I formatted the partition and went to install when I got this error.... Windows cannot install required files. The file may be corrupt or missing. Make sure all files required for installation are available and restart the installation. Error code: 0x80070017 I have used this disk before with no problems, but internet searching suggested I burn one at 2x speed because that helps for some reason... I'm burning one now, but my question is, why would I get this error, OTHER than the disc being bad? I'm pretty certain this one isn't as I have used it before... (ok so the slowly burned cd (using imgburn) didn't work either so it's DEFINITELY not the disc) Thanks in advanced for any answers Also I took one stick of ram out because internet searching also suggested that, but it didn't make a difference. Also I ran memory and hard drive checks and they passed fine. Also I reset the motherboard options to default What could it be!? Help I'm completely stumped...

  Read the article

• Remote Desktop Services Licensing - Does server have to have a RDS role?

  - by transistor1

  I recently set up a "micro" size Windows 2008 Datacenter server on Amazon AWS. My small group needs several concurrent RDS users to be able to access the machine. Without installing the "Remote Desktop Server" role, it allows 2 concurrent connections. I read on MS' website that in order to set up multiple users, we needed to install the RDS role. I did so, but now the application we are trying to share is running much slower than it was before. Prior to the role installation, it was taking about 5 seconds to open; now it is taking a few minutes to open -- without any other users logged on except me. My assumption is that the RDS role may be too much for this micro instance to handle, and currently, changing to another size instance is not an option (it may be possible later if we were to receive enough funding). This leads me to the following questions: 1) Is it a sensible assessment to assume that it is the RDS role is slowing things down, or are there other things that I could look at to speed it up? We are talking about a machine with ~600MB of memory. 2) If I revert back to the pre-RDS role, is there any legitimate way (in terms of purchasing RDS licenses) to get more than 2 concurrent desktops? I did read this, and am not questioning that the answerer is knowlegeable; but someone else may have some other experience. I am also making it clear that we want to do this in a legitimate way. Thanks in advance for any assistance that can be provided! EDIT: if it is helpful in answering the question, the application in question is a Lotus Approach database. Also, I am asking this from a technical perspective: not a legal one. I want to know if it is possible to install valid licenses without the RDS role.

  Read the article

• Slow manipulation of netfilter rules

  - by Ole Martin Eide

  I have a script maintaining gre tunnels and firewall rules using the "ip" and "iptables" tools. Setting up hundreds of tunnels, and adresses per interface runs just fine. Takes less than 0.1 second per interface, however when I get around to do the firewall rules everything slows down spending 0.5 per insertion. Why is it running so slow? What can I do to improve the speed? It seems like I could try ipset instead, but I really feel there is something wrong with the kernel or something. The interesting thing is that the first 10 rules runs fast, then it slows down.. mybox(root) foo# iptables -V iptables v1.3.5 mybox(root) foo# uname -a Linux foo 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux mybox(root) foo# cat test.sh #!/bin/sh for n in {1..100} do /sbin/iptables -A OUTPUT -s ${n} -j ACCEPT /sbin/iptables -D OUTPUT -s ${n} -j ACCEPT done mybox(root) foo# time ./test.sh real 1m38.839s user 0m0.100s sys 1m38.724s Appriciate any help. Cheers!

  Read the article

• Ram configuration 4x4 or 2x8?

  - by Carl B

  I am looking to upgrade my Ram to 16gigs and I am wondering if there is any distinct advantage of the way I do it. That being a 4x4 or 2x8 set up. In all my searching there have been a number of pros for each profile. I can find no benchmarck results for either setup as a compaison. So, if there are 2 profiles of the same speed, same voltage, same timing and same cas what would perform better or have a better over all benafit? A few examples from my search - a 4x4 set would lend a benafit in that if one stick failed, you only lose 25% of your Ram vs 50% in a 2x8 set up. a 2x8 set up would have less strain on the memory controler and motherboard. a 2x8 would generate less heat. a 2x8 set up is easier to over clock (not part of my need, but alot of the comparisons circled around the overclocability ease of the 2 stick set up). There is one outstanding benafit that I have found in at least the target company I have looked at and that is price. The 2x8 is nearly half the cost. My motherboard supports a max of 16 gigs and I have a 64 bit OS. Has anyone seen any performance comparisons or is 16 gb just 16 gb no matter how you slice it? And is there any merit to the above pros? Edit: as per the mobo specs - Main Memory • Supports four unbuffered DIMM of 1.5 Volt DDR3 800/1066/1333/1600*/1800*/2133* (OC) DRAM, 16GB Max

  Read the article

• Intel HD Graphics vs NVIDIA Quadro FX 380 PCI-E

  - by Michael

  I recently purchased an Acer Veriton which has an i5-650 processor, Windows 7 Pro (64 bit) and Intel HD Graphics listed as the video card. I also purchased a PNY nVIDIA Quadro FX 380 PCI-E card for improved picture and home video viewing and editing. I have already replaced the original 300 wattt power supply to a 430 watt Antec Truepower I had on hand and boosted the RAM to 8 gigs from the original 4. Question 1) Am I getting any improvement in visual quality or system speed with the Quadro or is it a waste of money and I should just save up to buy a bigger video card? This card was on sale for $115. If I am getting improvement then I need to ask another question. Question 2) Instructions for the Quadro installation are as follows... 1--Uninstall the existing VGA driver. -Remove the existing Display Driver via "Add or Remove Porgrams". -Shut down your computer. 2--Remove your Existing Graphics Board (or Disable Integrated 3D Graphics Controller). skipping instructions on how to remove existing graphics board -Systems with integrated (also know as on-board) 3D graphics may require you to disable the integrated 3D graphics system. Consult the owners or vendor manual that came with your PC on how to properly do this. So is the Intel HD Graphics considered a 3D graphics controller? If so should I just contact Acer or can anyone give me instructions? Thanks in advance for any help.

  Read the article

< Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >