Search Results

Search found 17267 results on 691 pages for 'dynamic ip'.

Page 300/691 | < Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >

• Icinga notifications are being marked as spam when sent to my mailbox

  - by user784637

  I'm using gmail and my domain is foo.com About half the notifications from my icinga server, [email protected] go to my spam folder for [email protected] Received-SPF: fail (google.com: domain of [email protected] does not designate <ip6> as permitted sender) client-ip=<ip6>; Authentication-Results: mx.google.com; spf=hardfail (google.com: domain of [email protected] does not designate <ip6> as permitted sender) [email protected] Is my current SPF record set up to allow my icinga server with the ip <ip4> and <ip6> to send email from the domain foo.com? ;; ANSWER SECTION: foo.com. 300 IN TXT "v=spf1 ip4:<ip4> ip6:<ip6> -all"

  Read the article

• Unable to connect to a remote SQL Server Instance over a VPN

  - by Jack Njiri

  I'm running SQL Server 2005 on two different servers running Win XP. The two servers are in different physical locations and are connected via a dedecated point to point data link in a virtual private network(VPN). Im only able to connect to the remote instance of SQL Server by specifying the IP address on the server name property. If I provide the actual server name say 'ServerA', then I get an error message. Everything works fine except configuring replication at the subscriber level, which requires the actual name of the instance, not an IP address or alias. I have already configured both instances on allow remote connections and im running the SQL Server Browser. How do I connect to the remote instance by providing the instance name? Alternatively how I configure subscription to a remote publisher without supplying the remote instance name?

  Read the article

• Netdom Join Failed To Complete Successfully

  - by BubbleMonster

  I have two servers on VMWare. One is a standard install of Server 2008 r2 and the other is Server 2008 core. Server 2008's IP is: 192.168.186.135 and computer name is: SERVER01. This is a domain controller and has DNS installed along with Active Directory. The domain is called: contoso.com Server 2008 Core's IP is: 192.168.186.137 and computer name is: SERVER02 They can both ping each other, but when I try running the following: netdom join SERVER02 /domain:contoso.com Results: The specified domain either does not exist or could not be contacted. The command failed to complete successfully. I'm thinking it might be a DNS issue? I'm new to servers and I am teaching myself. Any help would be appreciated. Thanks in advance.

  Read the article

• VPN pptp connection Unable to pass through linux iptables

  - by user221844

  I have set up a windows VPN server behind Linux - Ubuntu box that is working as firewall and proxy server. Now I want people from outside to be able to connect to the VPN server, but the connection is not being established and I get on the client an error 619. I have checked the problem on the internet and it seems a firewall issue. what should I do to make the connection established through the firewall? here is below the information about my setup Firewall-External-IF-IP: 172.16.1.100 Firewall-LAN-IF-IP: 192.168.1.1 VPN-Server-IP: 192.168.1.10 and below is my iptables file content: #Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *filter :INPUT ACCEPT [162000:140437619] :FORWARD ACCEPT [23282:27196133] :OUTPUT ACCEPT [185778:143961739] :LOGGING - [0:0] -A INPUT -p gre -j ACCEPT -A INPUT -s 192.168.1.10/32 -p tcp -m tcp --sport 1723 -j ACCEPT -A INPUT -s 192.168.1.10/32 -p udp -m udp --sport 1723 -j ACCEPT -A FORWARD -s 192.168.1.0/24 -o EXT_IF -j ACCEPT -A FORWARD -s 192.168.1.0/24 -i EXT_IF -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 192.168.1.10/32 -i EXT_IF -o INT_IF -p tcp -m tcp --dport 1723 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.1.10/32 -i INT_IF -o EXT_IF -p tcp -m tcp --sport 1723 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 192.168.1.10/32 -i EXT_IF -o INT_IF -p gre -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.1.10/32 -i INT_IF -o EXT_IF -p gre -m state --state RELATED,ESTABLISHED -j ACCEPT -A OUTPUT -p gre -j ACCEPT -A OUTPUT -d 192.168.1.10/32 -p tcp -m tcp --dport 1723 -j ACCEPT -A OUTPUT -d 192.168.1.10/32 -p udp -m udp --dport 1723 -j ACCEPT COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *nat :PREROUTING ACCEPT [17865:1053739] :INPUT ACCEPT [5490:357281] :OUTPUT ACCEPT [3723:223677] :POSTROUTING ACCEPT [3726:223870] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p tcp -m tcp --dport 1723 -j DNAT --to-destination 192.168.1.10 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p gre -j DNAT --to-destination 192.168.1.10 -A PREROUTING -i -h -A POSTROUTING -s 192.168.1.0/24 -o EXT_IF -j MASQUERADE COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *mangle :PREROUTING ACCEPT [22695965:17811993005] :INPUT ACCEPT [13818180:11522330171] :PREROUTING ACCEPT [17865:1053739] :INPUT ACCEPT [5490:357281] :OUTPUT ACCEPT [3723:223677] :POSTROUTING ACCEPT [3726:223870] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p tcp -m tcp --dport 1723 -j DNAT --to-destination 192.168.1.10 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p gre -j DNAT --to-destination 192.168.1.10 -A PREROUTING -i -h -A POSTROUTING -s 192.168.1.0/24 -o EXT_IF -j MASQUERADE COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *mangle :PREROUTING ACCEPT [22695965:17811993005] :INPUT ACCEPT [13818180:11522330171] :FORWARD ACCEPT [8527694:6271564562] :OUTPUT ACCEPT [14748508:11899678536] :POSTROUTING ACCEPT [23271280:18170828012] COMMIT # Completed on Thu May 29 12:40:18 2014 hope that I find the solution here ....!! :(

  Read the article

• How do I run the sphere-slicer.pl perl command to make a photo into a sphere?

  - by Mahdi Zenali

  I was looking for a program to slice pictures somehow to paste it on a globe(sphere). I found ip-slicer in this website. http://www.bruno.postle.net/2001/ip-slicer/ The problem I have is that I don't know where should I enter the command line. for example after running the program and entering this line "sphere-slicer.pl 16 1000 input.jpg" I get this this error Number found where operator expected at - line 72, near "pl 16" (Do you need to predeclare pl?) Number found where operator expected at - line 72, near "16 1000" (Missing operator before 1000?) Bareword found where operator expected at - line 72, near "1000 input" (Missing operator before input?) This program is written in perl language.

  Read the article

• FTP error 425 failed to establish connection

  - by cKK

  Getting "ftp error 425 failed to establish connection" when trying to connect to ftp server. Tried 2 ftp clients on 3 machines on same network and none work. However FTP works from home / mobile broadband. No ip blocks on ftp sever. Other ftp servers(differrent ip/hosts) work okay. firewall setup correct, no ports blocked. Is it possible to use a proxy for ftp a i think it's something with the ISP but taking too long to fix?

  Read the article

• MySql service stops under 2008 r2 x64

  - by volody

  I have installed MySql 5.5 server under windows 2008r2 x64 Apparently I can see that MySql service stops even if is configured to start automatically What can I do to find out why this is happening? MySql database is used as backend of ASP.Net web site Is it possible that web site was not active for a while and system stop mysql service? Update: It was mysql-5.5.7-rc-winx64. I could be an issue with this version (release candidate). Now I am trying to install mysql-5.5.8-winx64 And I have an issue with configuring MySql to work using name pipes I did uncheck use of TCP/IP protocol and configuration wizard just hangs Update: I have found workaround. It is required to configure MySql to use TCP/IP first, then reconfigure to use named pipes It looks like this link also has some information about the possible problems How should I diagnose ERROR 1045 during MySQL installation?

  Read the article

• How to use CLEAR USB internet connection in Ubuntu (host) and WindowsXP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for linux as yet. I've installed windowsxp as guest in ubuntu and the version I'm using is 3.2.2. USB is connecting fine in WindowsXP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• VPS DNS Resolution problem

  - by fatnic

  Hi. I've recently moved from a shared hosting to a VPS at vps.net but I think I might have broken it already! I have domain.com and domain.net. I have setup DNS records for both to point to my server. However, only domain.com pings to the correct IP address. domain.net is pointing to a different IP address. Possibly the old server it was pointing to. This has now been deleted. Is there possibly any way to correct this without having to submit a ticket to VPS.net?

  Read the article

• SYN flooding still a threat to servers?

  - by Rob

  Well recently I've been reading about different Denial of Service methods. One method that kind of stuck out was SYN flooding. I'm a member of some not-so-nice forums, and someone was selling a python script that would DoS a server using SYN packets with a spoofed IP address. However, if you sent a SYN packet to a server, with a spoofed IP address, the target server would return the SYN/ACK packet to the host that was spoofed. In which case, wouldn't the spoofed host return an RST packet, thus negating the 75 second long-wait, and ultimately failing in its attempt to DoS the server?

  Read the article

• Internet connection very slow after Linksys configuration

  - by NLV

  Hello We have this network setup Server1 - DHCP server, Domain Controller, AD Lease line for Internet connection From lease line to Linksys router (we dont use wireless though) From linksys to Netgear (24 port Switch) and vonage (VoIP) Netgear to all our machines We configured Linsys with the static IP and DNS server addresses our ISP gave and we have routed it correctly. All our work machines are configured with Get IP automatically DNS server addresses our ISP gave The problem is that none of the sites are getting opened promptly. It is taking around 5 minutes to load google.com. But we are able to ping all the sites. What could be the problem?

  Read the article

• [SOLVED]Need help with remote dekstop - Limit the computers you can access server from

  - by stirredo

  I have a windows server 2003 computer that is accessed by remote desktop connection. To access the server all you need to know is the IP address of the computer. I want to limit the computers that can access the windows server computer to authorized computers only. The authorized computers won't have static IPs, so I cannot limit them on basis of IP address. Can I limit them on basis of MAC id perhaps? I won't mind using third party solution like Teamviewer or Logmein etc. So How can I solve this problem? EDIT: Found a possible solution in team viewer. Team viewer creates a unique partner ID for the computer it is installed on. It has an option for allowing only authorized partner IDs to access the computer. Problem solved.

  Read the article

• How to statically configure DNS servers on a Cisco router when the WAN interface uses DHCP?

  - by Massimo

  I have a Cisco router (model 887VA, IOS 15.4) used to connect a LAN to the Internet via ADSL. The WAN interface uses DHCP: interface ATM0.1 point-to-point ip address dhcp I need the router to use a statically-defined DNS server for name resolution: ip name-server A.B.C.D However, the router insists on using the DNS servers supplied by the ISP via DHCP: Router#ping www.google.com Translating "www.google.com"...domain server (<ISP DNS>) [OK] Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 173.194.116.208, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/45/48 ms How can I tell the router to ignore the ISP-supplied DNS servers and only use the statically-configured one?

  Read the article

• VMWare Fusion cannot connect to the NAT connection on my Mac

  - by FFish

  I have been using VMWare Fusion on my Mac to check out my websites on localhost. Now I can't connect anymore with the NAT connection. There seems to be a problem with my IP address or Mac address? I have no idea what causes this, it was working fine before!? In the XP (SP2) VM, in the taskbar I see the Local Area Connection with the yellow warning icon. The bubble says: "This connection has limited or no connectivity. You might not be aisle to access the Internet or some network resources. For more information, click this message." Doing that opens up the Local Area Connection Status panel. In the Support tab, when I click the repair button I get following message: "Windows could not finish repairing the problem because the following action cannot be completed: Renewing IP address." Any help would be greatly appreciated.

  Read the article

• Port Forwarding for Remote Desktop

  - by Vaibhav Bajpai

  I have two Mac notebooks at home, I have assigned them static private IPs. I have also set my router to a DynDNS address, which updates everytime my router gets a new public IP. I have enabled Screen Sharing on both notebooks. I can successfully goto my router webpage using the DynDNS address. I understand I need to port-forward to get Screen Sharing to work from outside. Lets assume, notebooks have private IP 192.168.1.2 and 192.168.1.3 I am kind of lost here, would appreciate some help (I need to be able remote desktop to both notebooks)

  Read the article

• Connection timed out exception, why?

  - by Dheeraj Kumar Aggarwal

  I am developing an application which uses embedded tomcat server 7, and deploys a web application on embedded server. My application accesses the embedded webapp through Rest APIs, but my clients are getting Connection Timed Out exceptions and port is also not blocked. I never gets this exception when I install this application on my local machine. Some points: IP address is used in the host name part (They are able to access this IP address on other port) Port is not blocked We are using Apache HttpClient library to access the URL Timeout interval seems not to be an issue. What are the possible reasons for this exception Connection Timed Out? or How can I simulate this problem on my local machine? Any pointers would be helpful.

  Read the article

• setting up delegate or smtp forwarding

  - by cotiso

  for work we have a remote dedicated server to run our webservice that also runs our email services, at home(comcast residential internet) i cannot send mail using the dedicated server's SMTP, comcast spits back a error saying i can only use their SMTP server for sending mail at work(comcast business internet) we can use our dedicated server for sending mail with no problem so i set up a box at work to forward smtp traffic, i'm new to all this networking stuff by the way i used delegate to forward smtp traffic, can someone point me in the right direction on how to use this program(delegate) to fix our issue the delegate command i used to test is : delegated -P25 SERVER="smtp://dedicated.server.com:25" PERMIT=":::" -v i also opened up port 25 on the router so it points to my boxes ip are there any other ways to fool comcast into thinking im using my works ip to send mail, my coworkers and i are unable to send mail from home for some time now thanks

  Read the article

• Web Service gets unavailable after several concurrent calls

  - by Roman

  We are testing GoDaddy Virtual Data Center and came to a very strange issue when our web site gets unavailable. GoDaddy Support keeps saying the issue is in our web server settings, but looking at the result of our tests I doubt it. TEST ENVIRONMENT Virtual DataCenter with Windows hosted at GoDaddy.com. All servers have Windows Server 2008 R2 Datacenter, IIS 7. Server One with IP address 10.1.0.4 Server Two with IP address 10.1.0.3 Both servers are in private network not visible from outside. Port Forward with IP address 50.62.13.174. Port Forward is assigned to Server One TEST DESCRIPTION JMeter is used as a Client App to simulate 30 concurrent users sending 100 SOAP requests each. Interval between requests is 1 second. Http link used for testing: http://50.62.13.174/v2/webservices.asmx TEST ONE Test is run from a computer in our office. After JMeter starts running test, almost immediately, the link above becomes unavailable in a browser. After test completion, the link is not available in a browser for about 5 more minutes. Remote Desktop is working well, so we can connect to Server One remotely. After about 5 minutes since test completion, the link becomes available in a browser again. TEST TWO Test is run from Server Two (that is part of our virtual data center). Test works very well, no visible delays in processing. The link is available in a browser all the time. TEST THREE Test is run from Server One using localhost. The result is the same as in TEST TWO - no issues. TEST FOUR We repeated TEST ONE from other computers that we have located in different countries, all with the same result as TEST ONE. CONCLUSION As the test works well from Server Two, but does not work from outside our virtual data center, we feel there are issues with the network or its capacity. The whole behaviour looks like out requests from outside get stuck somewhere before reaching our virtual data center. Has anybody had similar issues in the past? Are there chances that something is wrong with our server settings?

  Read the article

• Why might one host be unable to access the Internet, when it can ping the router and when all other hosts can?

  - by user1444233

  I have a Draytek Vigor 2830n. It's kicking out a 192.168.3.0 LAN. It performs load-balancing across dual-WAN ports, although I've turned off the second WAN to simplify testing. There are many hosts on the LAN. All IPs are allocated through DHCP, most freely allocated from the pool, but one or two are bound to NIC MAC addresses. All hosts can access the Internet, save one. That host (192.168.3.100 or 'dot100' for short) gets allocated an IP address (and the right gateway address, DNS server addresses, subnet etc.) dot100 can ping itself. It can ping the gateway, and access the latter's web interface via port 80. It's responsive and loss-free (sustained ping over a couple of minutes reports no data loss). Yet, for some reason that evades me, dot100 can't ping an external IP address or domain name. I suspect it's never been able to, because it was getting some Internet access from a second adaptor (different subnet), but that's now been turned off, which exposed the problem. In dot100, I've tried: two operating systems (Windows 8 and Knoppix), to rule out anti-virus programs etc. two physical adaptors two cables, on each adaptor two IPs (e.g. .100 and .103 assigned by Mac and .26 from the pool) both dynamic and assigned (MAC-bound) DHCP-allocated IPs but none of this experiments yielded any variation in the result. dot100 is a crucial host. It's a file server for the network, so I need it to be reliably allocated a consistent IP. Can anyone offer a potential solution or a way forward with the analysis please? My guess My analysis so far leads me to believe it's a router issue. I've checked the web interface very carefully. There are no filters setup in Firewall - General Setup or Filter Setup. I suspect it's a corrupted internal routing table, but the web UI shows this as the Routing table: Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 62.XX.XX.X WAN1 * 62.XX.XX.X/ 255.255.255.255 via 62.XX.XX.X WAN1 S 82.YY.YYY.YYY/ 255.255.255.255 via 82.YY.YYY.YYY WAN1 C 192.168.1.0/ 255.255.255.0 directly connected WAN2 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2

  Read the article

• Can a Windows 2003 Active Directory server act as a NTP server?

  - by Rob Nicholson

  Within our LAN, there are two Windows 2003 servers with the Active Directory role. Both these servers have the time service configured to query NTP servers on the internet for the accurate time. That works fine. I've just installed XenServer v5.6 and it's asked me for the IP address of an NTP server. Without tweaking the firewall, I cannot configure this server to reference an internet based NTP server. But can I configure it to use the IP address of the internal AD servers, i.e. do AD servers also act as NTP servers to other computers? Thanks, Rob.

  Read the article

• What equipment do real ISP's use?

  - by Allanrbo

  In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers? What we ended up doing In case anyone are courious, we ended up doing seperate VLANs for each user. And as a matter of fact, not just the 550 users, but for 2500 users (11 dorms). Here's a page describing the setup: http://k-net.dk/technicalsetup/ (the section "Transparent firewall using VLANs"). There was no significant load on the router server as I feared in one of the comments below. Even at 800Mpbs.

  Read the article

• How do http proxies determine https traffic with a single port?

  - by badunk

  If a proxy receives the tcp packet, then the destination ip address and port are that of the proxy. In that case, I imagine the only way a proxy can still resolve the intended destination is either through routing the source ip address/port or through the host field in the http header. Is this correct? In both Fiddler and Charles http proxies, I noticed that the tool accepts both http and https connections through a single port that you can specify. What do these tools do to tell the difference between the two types of connections?

  Read the article

• Why is this static routing not working ?

  - by geeko

  Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

  Read the article

• Configuring a Unified Communications Certificate for many virtual hosts running in Jetty

  - by rrc7cz

  I have a single IP with Jetty serving up X sites on port 80. Basically you can sign up for our service, then point your domain www.mycompany.com to that IP, and Jetty will serve up your custom site. I would like to add SSL support for all sites. To simplify things, I've looked at getting a single Unified Communications Certificate to plug into Jetty and have it work for all sites. Is this possible? Has anyone done this before? Does Jetty only support traditional, single-domain certs? What issues might I run in to compared to a single-domain cert?

  Read the article

• cannot connect to MS FTP 7.5 on Windows 2008 on Amazon EC2 instance

  - by minerj

  I have just installed the MS FTP 7.5 upgrade on my Windows 2008 Server (Service Pack 2) running on an Amazon EC2 instance. In the FTP Firewall Support settings for the server in IIS Manager I have set up the passive port range 45001 - 45005 and also set the External Firewall IP address to match the assigned Amazon Elastic IP address. Using the AWS Console I changed the Security Group for the server to allow access to the server through ports 21 and 45001 through 45005. Using an FTP client (either the command line FTP client or Windows Explorer) on the Amazon server I can connect to the FTP server but I cannot connect with an external FTP client. When I checked to see which ports were open on the server using Shields Up it shows that port 21 is open but ports 45001 to 45005 are closed. I assume I'm missing something. Any help greatly appreciated.

  Read the article

< Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >