Search Results

Search found 9381 results on 376 pages for 'wireless driver'.

Page 309/376 | < Previous Page | 305 306 307 308 309 310 311 312 313 314 315 316  | Next Page >

  • 10.04 Window manager not working

    - by jackg
    Using an old mx200 128Mb AGP card. Log in ok. Sometimes the top and bottom bars do not appear, sometimes one sometimes both sometimes none. The menus on firefox/thunderbird and others disappear when I move the pointer from the menu heading to the menu itself. I can't play you tube videos, nor pacman, so the world has ended as I know it. If I type sudo metacity --replace in a terminal the window manager seems to work fine. But I don't know how to make this permanent. One option was: System menupreferencessessions In the sessions tab make sure that "automatically save changes to session" is checked. I don't have a sessions option in the preferences menu. So...? Must be a line of code in a terminal I can use to get round this. I have not upgraded to Ubuntu 11... because the graphics card is so old that I cannot get any decent screen resolutions when I do. On 10.04 I disable the Nvidia driver for the same reason and use 1024x768. Ta

    Read the article

  • No sound after upgrading to Ubuntu 11.10 from win7

    - by Tilman
    just as a prefix to my question, i'd like to note that i'm just now entering the world of Linux (unless you count my android, but that's a very different experience...) i have two computers now that run Ubuntu 11.10, the first of which i've had very little problems with, aside from figuring out the basics. the second, from which i'm writing this question, has (up to this point) only had one problem.... no sound. i've read a couple questions similiar and found little help as the component catalog doesn't have my computer listed. (in fact i'm not suprised this is a pos i had my mom grab from her work before they officially closed the doors behind them) had perfect sound before hand, and no sound now. sudo lspci -v brings up 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) Subsystem: Intel Corporation Device d608 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at ff980000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel any help would be greatly appreciated, me and my gf just wanna watch a damn movie lol

    Read the article

  • How do I debug xorg/fglrx related system freezes on Ubuntu 12.10?

    - by racerror
    My brand new system is randomly freezing and I don't know how to debug the issue. System: AMD A10-5800k Asus F2A85-M motherboard Integrated Radeon HD 7660D 8gb Samsung ddr3 1600 Ubuntu 12.10 Gnome shell / Unity (issue exists in both) xorg.conf (relevant parts): Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:0:1:0" Option "TexturedVideoSync" "on" Option "UseFastTLS" "2" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "Monitor0" DefaultDepth 24 Option "UseEDID" "False" Option "ExactModeTimingsDVI" "True" Option "NoBandWidthTest" "true" Option "ModeValidation" "AllowNon60hzmodesDFPModes, NoEDIDDFPMaxSizeCheck, NoVertRefreshCheck, NoHorizSyncCheck, NoDFPNativeResolutionCheck, NoMaxSizeCheck, NoMaxPClkCheck, NoEDIDModes" Option "UseEDIDDPI" "False" Option "UseEDIDFreqs" "0" Option "NoLogo" "True" Option "Coolbits" "1" Option "metamodes" "DFP-0: 2560x1440_60 +0+0" SubSection "Display" Depth 24 Modes "2560x1440" EndSubSection I ran memtest on my ram and it checks out fine. I have tried using the latest fglrx and fglrx-beta. I have loaded 3.6.x kernel. I do not see anything relevant in dmesg, kern.log, syslog, .xsession-errors or Xorg.log. I cannot ssh into the machine when frozen from another machine. I know that system resources not being stressed when the crashes happen. It seems that video and any gaming (very simple graphics games) contribute to the freezes most frequently. However, I have experienced the crash before when just using Chrome. I suspect the crashes are xorg/fglrx related, but I have no evidence to back that up. Where should I look? What should I grep for? What should I try next?

    Read the article

  • How to refactor to cleaner version of maintaing states of the widget

    - by George
    Backstory I inherited a bunch of code that I'd like to refactor. It is a UI application written in javascript. Current state: We have main application which consist of several UI components. And each component has entry fields, textboxes, menus, etc), like "ticket", "customer information", etc. Based on input, where the application was called from, who is the user, we enable/disable, hide, show, change titles. Unfortunately, the app grew to the point where it is really hard to scale, add new features. Main the driver (application code) calls set/unset functions of the respective components. So a lot of the stuff look like this Main app unit function1() { **call_function2()** component1.setX(true); component1.setY(true); component2.setX(false); } call_function2() { // it may repeat some of the code function1 called } and we have a lot of this in the main union. I am cleaning this mess. What is the best way to maintain the state of widgets? Please let me know if you need me to clarify.

    Read the article

  • Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

    - by user42424
    So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

    Read the article

  • How to disable discrete GPU using NVIDIA drivers?

    - by penzoiders
    I have a DELL studio XPS 13 (aka 1340) as of 12.04 most things run smoothly out of the box, but I have some power draining and warmness issues (if not to be called terrible heat issues) The system came with a NVIDIA GeForce 9500M (which has Hybrid SLI) and it shows up in "lspci" as these 2 cards 02:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce 9200M GS] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation C79 [GeForce 9400M G] (rev b1) I had to install nvidia-current over noveau driver 'cause noveau does freeze the system after suspension. By installing nvidia-current and running nvidia-xconfig the resume process after suspension is fixed. By the way both with nvidia-current and noveau the system drains a lot of battery and heats up a lot. I suppose this is because the discrete GPU is always on. I don't really need 3D graphics on this system, if not the minimal to run unity and compiz for window management. So my question is: How do I disable, using nvidia-current, the discrete GPU 9200M and use only the integrated one 9400M? notes: In BIOS I have no option to disable discrete GPU This I think is not applicable because of the suspension-freeze issue (with noveau): https://help.ubuntu.com/community/HybridGraphics I've found this but I don't know which --sli option I should choose to fit my needs: http://manpages.ubuntu.com/manpages/hardy/man1/nvidia-xconfig.1.html My system has not optimus or cuda, but anyone can tell me if bumblebee can work for me?

    Read the article

  • 12.10 no audio via hdmi and video speeds up

    - by jackson
    I have a laptop with an ati radeon 4200, on 12.04 everything worked fine, since upgrading to 12.10 I cannot get sound over the hdmi. When I switch to hdmi audio the video speeds up to about 2x. I can use the speakers in my laptop and watch video via hdmi with no problems. Things I have tried: Various tutorials to install the AMD/ATI drivers, all of which resulted in low graphics mode. Checked that everything is properly set in alsamixer, the sound utility and - installed pavucontrol and checked everything in there. Verified the output from cat /proc/asound/cards looks normal When I initially upgraded there was a plethora of problems which I believe were due to the old proprietary driver still being used but not compatible, after a few hours trying to fix that I decided just to back up and do a fresh install which works great except for the above stated problem. Any help would be greatly appreciated!! Finally hopefully this hasn't already been answered, I have tried a few different searches on the boards and haven't come up with anything. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SB [HDA ATI SB], device 0: ALC269VB Analog [ALC269VB Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0] Subdevices: 0/1 Subdevice #0: subdevice #0

    Read the article

  • Ubuntu 13.10, kernel 3.11 blank screen issue with hybrid graphics

    - by Lagerbaer
    On my HP Envy, which has both an Intel on-chip graphics card and an Nvidia Geforce: *-display UNCLAIMED description: 3D controller product: GK208M [GeForce GT 740M] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:d2000000-d2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:5000(size=128) memory:b2000000-b207ffff *-display description: VGA compatible controller product: 4th Gen Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d3000000-d33fffff memory:c0000000-cfffffff ioport:6000(size=64) I have trouble with all newer kernels. I basically had to install 12.04 LTS and use their 3.5 kernel family to get the system to boot. The 3.8 from 12.10 or the newest 3.11 from Ubuntu 13.10 leave me with a black screen upon boot. On one occasion I did hear the "log in" sound, but the screen did not display anything. I have purged all nvidia drivers so I guess it should just use the intel drivers, but apparently this is all messed up with newer kernel versions. This is different from the other "nvidia boots into blank screen" bug in that I don't rely solely on an nvidia card. Surely the intel on-chip card should be supported and leave me with something different from a blank screen? Again, it only works with kernel versions 3.5.0-41-generic, not with the 3.11.0-12 one that ships with Ubuntu 13.10. When I go into the grub menu and change the boot options from 'quiet splash' to 'nomodeset' I am able to boot the system, but then I don't get any graphics and trying 'sudo service lightdm start' doesn't succeed (I get 100% CPU for apport, but this doesn't do anything either, so I kill it). Help, I'm all out of ideas. EDIT: Let me add that I'm using the EFI boot system and have a dual-boot installation with Windows 8.

    Read the article

  • Wired card not connecting after trying to connect

    - by Mike
    I have an Ubuntu 12.10 PC. When I plug in my internet cable it starts connecting and after a minute it says it can't connect. I tried different cables but nothing works. Wlan works. I think it's the network driver but I don't know how to install/update it. Here's the ifconfig info (if it helps): eth0 Link encap:Ethernet HWaddr 00:01:6c:39:2a:8d inet6 addr: fe80::201:6cff:fe39:2a8d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2011 errors:0 dropped:362 overruns:0 frame:0 TX packets:586 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:175452 (175.4 KB) TX bytes:147211 (147.2 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9779 errors:0 dropped:0 overruns:0 frame:0 TX packets:9779 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8460080 (8.4 MB) TX bytes:8460080 (8.4 MB) wlan0 Link encap:Ethernet HWaddr 08:10:74:35:99:9d inet6 addr: fe80::a10:74ff:fe35:999d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1790 errors:0 dropped:0 overruns:0 frame:0 TX packets:3250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:401664 (401.6 KB) TX bytes:2898773 (2.8 MB)

    Read the article

  • Can't login to Unity 3d after enabling Xinerama for a short moment

    - by Amir Adar
    Today I connected a second monitor to my computer. I set it up using nVidia's control panel, and all was working quite well, so I figured it won't be a problem to try Xinerama, just to see the difference between that and twinview. After enabling Xinerama and restarting the X session, I saw that I was logged into a Unity 2d session. I thought it was a problem with Xinerama, so I switched back to twinview, but it still logged me into Unity 2d. I tried disconnecting the second monitor, no luck: still Unity 2d. I tried changing GPU drivers and installing drivers from a separate ppa, and still I was logged into Unity 2d. Up until this point, I didn't have any problem logging into Unity 3d. It only happened after I tried using Xinerama. I should note that I was doing all this while updates were going on in the background, so it could be something related to that, though I can't imagine what (I tried booting with another kernel, but no luck). So what exactly happened? Did changing the mode to Xinerama triggered some other changes that I'm not aware of? Did these updates cause a certain malfunction in the driver? Is it something else?

    Read the article

  • 1080p Screen resolution problem after 10.04 to 12.04 update

    - by Ale
    I have a Samsung LCD 40" with a NVidia GeForce 6150SE nForce 430 Card. I recently upgraded from 10.04 to 12.04 and the best resolution I can get is 1360x768. I've tried the propietary drivers available on the repository kmod:nvidia_current kmod:nvidia_173_updates kmod:nvidia_current_updates kmod:nvidia_96 kmod:nvidia_96_updates kmod:nvidia_173 I've also downloaded latest from NVidia's Web, version: 295.40. But still no luck. With Nouveau driver, I can only get 1024x768. I know there is no problem with my hardware (video card, cable and monitor), I was using it perfectly on 10.04. Can anybody suggest something else I could try, to get my 1920x1080 resolution back? Thanks in advance. Here are some more information, that I got reading other similar posts on askubuntu. $ lspci | grep VGA 00:0d.0 VGA compatible controller: NVIDIA Corporation C61 [GeForce 6150SE nForce 430] (rev a2) $ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 240, current 1360 x 768, maximum 1360 x 768 default connected 1360x768 0 0 0mm x 0mm 1360x768 50.0 52.0* 1024x768 51.0 800x600 53.0 54.0 55.0 680x384 56.0 57.0 640x480 58.0 576x432 59.0 512x384 60.0 400x300 61.0 62.0 63.0 320x240 64.0

    Read the article

  • Impossible quandrary involving UCK, graphics card, and Nvidia drivers

    - by InkBlend
    I have a computer that I want to install Ubuntu on. It is an older gaming computer with a Nvidia graphics card. When I attempt to boot any unmodified Linux distribution onto it, I get a "Boot error" message, which I assume is because the computer uses a discrete graphics card, which the Linux kernel does not have support for. Ordinarily, that would not be a problem, as I would just plug the monitor into the VGA port built in to the motherboard. However, this particular model of motherboard does not have an on-board graphics connector, so I am stuck with using the graphics card connection. That further would not be a problem; all I would have to do would be to use UCK to create a customized Ubuntu image that included the graphics drivers. Except for the fact that the Nvidia Linux drivers must be installed on a computer with a Nvidia graphics card present. So while using UCK, the driver installer fails with a message stating that there is no Nvidia graphics card present. How do I get Ubuntu on my desktop computer?

    Read the article

  • Essbase Analytics Link (EAL) - Performance of some operation of EAL could be improved by tuning of EAL Data Synchronization Server (DSS) parameters

    - by Ahmed Awan
    Generally, performance of some operation of EAL (Essbase Analytics Link) could be improved by tuning of EAL Data Synchronization Server (DSS) parameters. a. Expected that DSS machine will be 64-bit machine with 4-8 cores and 5-8 GB of RAM dedicated to DSS. b. To change DSS configuration - open EAL Configuration Tool on DSS machine.     ->Next:     and define: "Job Units" as <Number of Cores dedicated to DSS> * 1.5 "Max Memory Size" (if this is 64-bit machine) - ~1G for each Job Unit. If DSS machine is 32-bit - max memory size is 2600 MB. "Data Store Size" - depends on number of bridges and volume of HFM applications, but in most cases 50000 MB is enough. This volume should be available in defined "Data Store Dir" driver.   Continue with configuration and finish it. After that, DSS should be restarted to take new definitions.  

    Read the article

  • Twinview broken on upgrade to ubuntu 10.10

    - by mapkyca
    I have been on 9.10 for over a year on the grounds that if it ain't broke, don't fix it. However, I had a spare weekend and figured it was probably about time... I performed an upgrade to 10.4, and everything seemed to proceed smoothly, so I took the plunge and went for 10.10. Disaster. My twinview Nvidia display which had been working perfectly is now broken. On boot everything seems fine, but when X starts and the second monitor springs into life the primary winks out and switches off - almost as if its been put into an unsupported display mode. The system seems to think there's a second monitor - the nvidia logo is split across the two screens, but it can't seem to start. Things I've tried: Swapping the monitors (one is older than the other, and its definitely the port not the actual monitor) Rolling back to an old Xorg conf from prior to the upgrade Installing a non-beta driver direct from Nvidia (this seems to start both monitors but then apparently stops boot and causes the second display to 'wink'. Twinview seems non-functional, both displays are mirrors) Disabling EDID Disabling twinview, logging in and attempting to use the Nvidia config to re-detect the monitors (second monitor is falsely detected and won't go higher than 1024x768. Selecting 'apply' causes one screen to go blank and the other to display garbage) googling for about 5 hours looking for similar problems, none of the offered solutions seemed to work I'm at a loss, and it is looking very much like I'm going to have to go through a time consuming reinstall to downgrade back to the working 10.4. Any thoughts?

    Read the article

  • Double entries in the gnome 3 task bar

    - by Mark
    I am running Ubuntu 12.04 with Gnome 3. All was working well except that graphics were slow and even moving a window on the screen seemed slow. I installed the fglrx ati driver. Which seems to have improved matters. But on first login I had all gnome items duplicated. That is my task bar has the ubuntu sign, then says Applications, then places then the ubuntu sign then Aplications and then places. Any application I run produces two icons at the bottom of the screen. This was after a reboot. I rebooted again. Now I have 3!! On the right each set of icons such as printer is also trippled!! See screenshot at http://jetmark.co.uk/Screenshot.png See Dmesg at http://jetmark.co.uk/dmesg.txt Any suggestions welcome. Reboot - now I have 4!! So one set gets added on each reboot. Help!! I am going to be task barred out before long!!

    Read the article

  • Random compositing lag

    - by user1020567
    My laptop specs: 512 mb of RAM, out of which 64 mb are shared with an integrated GPU - ATI Radeon Xpress 200 M. Intel 1,6 Ghz Celeron M single-core processor. I've spent months trying to figure out why compositing and effects sometimes lag on any distro I try. Now I've come to realise that no matter what drivers I try (the default ones work for me on pretty much any linux) compositing lag is random. When I used Ubuntu 10.10, for example, sometimes window compositing would lag and sometimes it wouldn't. The PC is able to render those effects so hardware is not the problem. It's completely random and unpredictable - sometimes when I turn on the computer the effects lag horribly and sometimes it's completely smooth. I've also checked startup items and there doesn't seem to be any unnecessary entries. I also tried building my own OS with Arch Linux and the problem persists there, therefore I can only assume that it's a driver issue of some sort. By default there are lots of drivers supplied with linux distributions. Could it be that they're in the way? The ones that I need are ati/radeon (or both? What's the difference between them?) and there seem to be a lot of others... What should I do?

    Read the article

  • How do I troubleshoot system slowness seen when viewing PDFs or videos?

    - by asp
    Whenever I watch videos, either online of local via Totem and/or open PDF files using evince. The system gets really, really bogged down. All apps get really slow, menus take forever to display, switching windows gives me time to make a coffee, etc. I have a couple of bug reports open on this, but what do I need to do to really troubleshoot the issue? I've purged Adobe Flash from the system, but YouTube HTML5 videos still have the issue. A bunch of PDFs saved locally trigger the problem. And to (temporarily) remove the slowness, I need to shutdown the computer, breath for a few minutes, then restart. A simple reboot does not do the trick. How can I identify the cause? This only started on 13.04. I've had Ubuntu on this machine for a year without a problem until "upgrading" to 13.04. I am not a programmer, but I suspect an issue with the Intel video driver. Is there something I can run which will diagnose this, or are there concrete steps I can follow to find the culprit?

    Read the article

  • ubuntu 12.10 Lenovo b570e, WiFi connected but not working

    - by koogee
    I'm running ubuntu 12.10 liveUSB on a lenovo b570e. It has an atheros wifi card that connects with my home network but I can't browse AT ALL. My network is multiple clients --> router --> isp modem --> Internet I can ping my router (192.168.0.1) but not my isp's modem(192.168.15.1). I have 3 other computers connected to the same router that are working fine (infact i'm posting from one) ping -c 3 google.com unknown host google.com ping -c 3 8.8.8.8 shows 100% packet loss I think its some networking issue. I tried directly connecting it to the router via ethernet cable but same issue. It gets an ip, shows LAN connected but can't browse. If I connect it directly to the isp modem via ethernet cable it starts working fine. Connection Information shows: Interface: 802.11 wifi (wlan0) driver: ath9k security: wpa/wpa2 speed: 150mb/s ip: 192.168.0.106 broadcast: 192.168.0.255 subnet:255.255.255.0 default route: 192.168.0.1 primary dns: 192.168.15.1 i have restarted the router and modem many times. Rebooted the LiveUSB many times.

    Read the article

  • How to get "Fn" keys to work (Asus 4830T)? (specificly, the "suspend" key)

    - by Pointy
    I've got an Asus 4830T onto which I've just re-installed 12.04 because I installed an SSD. I was running 12.04 before too, which had been upgraded over a few releases. At some point on that old install, I had gotten all the "Fn" keys to work, or at least all the ones I cared about. (Oh except I think the screen brightness keys never worked.) I have no recollection of what I did. Anyway now things are fine, and some of the Fn keys work: the one to turn of the trackpad and the one to turn off wireless (grr I hate that one). However, the "suspend" key for some reason does not work. Now the system will suspend and resume just fine, but I'm having to do it from the menu. Is there an easy (or hard) way to make those work? I'm running straight Ubuntu but with Xfce installed as my normal desktop. (In other words, it's not Xubuntu, though I doubt it matters.) I recall at some point having found some arcane mapping mechanism to bind the Fn keys to actions, but I can't find it now. (I'm perfectly OK with editing weird files; I'm a long-time Unix user.) (Very long-time.)

    Read the article

  • Unable to view 2 local sites over network

    - by gentrobot
    I have 2 websites running on my local machine that I'd like to view from other machines on the same network. For /etc/apache2/sites-available/site1.com: <VirtualHost *:80> ServerName site1.com DocumentRoot /var/www/answers/app/webroot DirectoryIndex index.php <Directory "/var/www/answers/app/webroot"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> For /etc/apache2/sites-available/site1.com: <VirtualHost *:80> ServerName site2.com DocumentRoot /var/www/answers2/app/webroot DirectoryIndex index.php <Directory "/var/www/answers2/app/webroot"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> I have added 2 entries in the /etc/hosts file as: 127.0.0.1 site1.com 127.0.0.1 site2.com Now, when I point the browser on my machine to site1.com, it shows me the first site and pointing the browser to site2.com, it shows me the second site. However,when I type in the local IP of my machine in the browser, it always shows site2. How can I change it to switch between site1 and site2 ? Is there a way that I can view both the sites form another machine (esp. mobile devices over wireless network) ?

    Read the article

  • How do I restore default menu/top panel text color in Gnome Classic?

    - by Kobby
    The default text/icon color in my top panel has changed from white to a very dark grey, making my menus virtually unreadable against the black of the Ambiance theme. This includes even the login screen menu. I used Gnome Tweak to change the theme to Adwaita, but while some text has gone light grey (e.g. Date/Time), the login menu text remains dark grey, as do most icons (e.g. dropbox, wireless, battery indicator...) in the top panel after I log in. I tried deleting the top panel altogether but the option of deleting under Super + Alt + Right Click is blocked off. I tried running a panel from the terminal, but it came up in strange colors too, plus icons had moved around and some parts of the panel were opaque and other parts transparent. Deleting the panel wouldn't solve the basic problem anyway, as my login menu would still be very dark grey and unreadable against the default (black) Ambiance background. I would like to keep Ambiance but I want to reset the color to default (white) again. Can anyone help me?

    Read the article

  • LiveCD/USB boot issues with Ubuntu 12.04 on blank drive

    - by Richek
    Not sure how common this issue is, or even how badly I may be missing something simple, but I am a first time usuer having some serious problems. Some background: old HDD running Windows 7 developed too many bad sectors and is bricked. I'm attempting to install Ubuntu 12.04 on a fresh 1TB drive by booting from a liveCD USB flash drive. I've not been able to get past the initial menu screen, however, as the process stalls out shortly after selecting an option (both boot from drive and install to drive). I've tried multiple USB drives as well as CDs, modified the boot order, flashed BIOS, and even tried booting with only the flash drive and the keyboard connected with the same results.Typically what I observe is that the OS begins what I think is compliling, listing drivers and components before freezing on one. When the keyboard is plugged in, its the keyboard driver, before I flashed BIOS, it was a BIOS related item, now its an unknown entry. The computer seems to be reading the drive (idicated by USB light flashing or CD drive reving) for roughly 10 minutes with no progress, followed by the drives going quiet. Some spec info: Motherboard: ASUS P5Q Pro, BIOS version 2102 (latest version), Intel chipset CPU: Intel Core 2 Duo E8400 Wolfdale 3.0GHz help would be appriciated!

    Read the article

  • How can I extend the desktop onto an external monitor/projector?

    - by hellocatfood
    I've plugged in a projector into my laptop and I'm attempting to extend the desktop onto it (so that I can run a full screen app on the projector and have the controls on my laptop). I'm able to mirror the screens effectively (it does this by default) but I can't extend it. When I untick "Mirror screens" and press apply it asks me to log out and then back in again but it goes back to mirroring the screens. I'm able to extend desktop on to my external monitor at home, just not this projector. Is there a manual way or other way to do this other that through Monitors setting? My computer model is Dell Studio 1555: Pentium Dual Core T4300(2.1GHz,800MHz,1MB), 4096MB 800MHz DDR2 Dual Channel, 512 MB ATI Mobility RADEON HD 4570 using the ATI proprietary driver. My screen resolution is 1366x768 (16:9) The projector that it wont connect properly is a Hitachi CPX3. That page specifies that it's especially designed for projectors that use 16:10 aspect ratio, but considering my external monitor at home uses 4:3 should the differences in aspect ratio matter or be causing this error?

    Read the article

  • Enabling GTX 570

    - by Silas
    Hello i just built up my new system: Asus Rock Z77 Extreme 4 Intel i7 3770k 16 Gb Corsair Ram Zotac Nvidia GTX 570 bequiet! 630W Power supply 120 GB SSD So after i installed UBUNTU 12.04 64 bit. It ran smoothly. I downloaded and installed all the recommended updates. After checking the Sytem details the GTX 570 didnt show up as graphics unit. so i figured i needed to download the drivers. So i did but being a complete newbie to linux i didnt succeed in installing them. (I think) Anyway after several tries and errors i shut down the PC and restarted it. Resultung in do Signal to my screen after trying to reboot and all the monitor outs with no result i took out the graphic card and now it boots normally but after booting it says there is a problem with the system the graphics cant be recognized something something. So Question A: What do i do? I Like linux but the arbitrarity of the Errors that occur without any changes to the system scare me. Question B: Is there A beginners guide to Ubuntu where i could start from scratch because i really want this to work? Question C: Now that the System is (suddently) showing these graphic errors So far without visible consequence despite the error message. should i reinstall the GPU and give the driver installation another try or the other way around? Ill be very grateful for any help. Thank you in advance!

    Read the article

  • Custom LightDM sessions to launch an application

    - by zachtib
    I'm trying to set up Ubuntu to act as a kiosk running a custom application, and am trying to get a LightDM session built to automatically start it. Ideally, I'd like to have two sessions available from LightDM. The default would start my application fullscreened, and the other would open a minimal desktop in case any configuration (mostly connecting to a wireless network) needed to be done. I've done a lot of research over the last week on custom LightDM & Gnome sessions. I've got a custom greeter written for LightDM that can start either session, but I can't figure out how to add a specific application to the Gnome session that is ultimately started without just putting a launcher in the global startup directory, and I don't want to do that since I don't want the application starting when they open "configuration mode". Another problem I've run into on my current workaround is that the application doesn't fullscreen properly, which makes me think I'm not starting enough of a gnome session (currently it's just metacity, no panel or anything else). Edit: I found a solution. See http://www.webupd8.org/2011/11/make-applications-autostart-only-in.html

    Read the article

< Previous Page | 305 306 307 308 309 310 311 312 313 314 315 316  | Next Page >