Search Results

Search found 11077 results on 444 pages for 'no such ip'.

Page 314/444 | < Previous Page | 310 311 312 313 314 315 316 317 318 319 320 321  | Next Page >

• Is it possible to limit output bandwidth between eth0 and lo?

  - by mmcbro

  I'm trying to limit the bandwidth between my eth0 output (nginx proxy) to my loopback inteface (apache) by filtering on destination port. Incoming Packet -> Eth0 -> 0.0.0.0:80 Nginx -> tc qdisc class/iptable mangle 2525port -> 127.0.0.1:2525 Apache I don't know if it's even possible I'm just experimenting. My rules are the followings : tc qdisc add dev eth0 root handle 1:0 htb tc class add dev eth0 parent 1:0 classid 1:10 htb rate 2mbps ceil 2mbps prio 0 tc filter add dev eth0 parent 1:0 prio 0 protocol ip handle 10 fw flowid 1:10 iptables -A OUTPUT -t mangle -p tcp --dport 2525 -j MARK --set-mark 10 I also tried to with FORWARD chain but its still the same.

  Read the article

• Ubuntu VPN Server (PPTPD) Configuration - Pass Traffic to Internet

  - by SnAzBaZ

  I am trying to configure PPTPD on my Ubuntu box to pass all VPN traffic through to it's internet connection, so I essentially want it to work like a Proxy. I think the problem is that no default gateway is being assigned to my PPTP client (Windows 7). I can connect to the VPN fine, I get an IP address and DNS servers but no default gateway. Do I need to configure a specific option to tell the VPN server to forward all traffic it receives down it's eth0 port and out to the internet. Thanks!

  Read the article

• How do I configure networking on CentOS 6 running on hyper-v?

  - by LonelyLonelyNetworkN00b

  I'm not using legacy adapters, and i've installed Linux Integration Components 3.2. THe problem i'm facing is that the command 'setup' or 'system-config-network' doesn't list any network interfaces. If i run ifconfig -a i can see both the network cards i've attached. By setting a ip using ifconfig i can get network connectivity. The problem is that it's not persistent after a reboot. I'm a 100% centos newbie, but I figure it has something to do with that the centos installer couldn't see the NICs on install. How can I fix this?

  Read the article

• Linksys WRT54GS V6 Router Blinking Power Light

  - by Frank

  I have a Linksys WRT54GS V6 Router in my possession got it at my local goodwill for 5$. Upon start up the Power LED starts flashing like crazy and at the same time the Ethernet ports all light up once then turn off (DMZ and WLAN never turn on). I can ping the router only by setting a static IP on my Pc. I can also successfully push a file (official Linksys OS and DD-wrt) into it via TFTP but this currently does nothing (no 192.1681.1 Access). Any ideas as to what may be wrong? I think its pretty obvious that it's bricked but.. I keep hearing a whole lot of "if it pings it's fixable" on the internet.

  Read the article

• Windows Server 2003 - passwordless access to \\myhost\ but not \\myhost.mydomain.net\

  - by Charles Duffy

  I have a Windows Server 2003 system on which passwordless access to local UNC paths is possible using the server's unqualified hostname or its IP address, but not via its FQDN -- even when the hosts file is used to map that FQDN directly to 127.0.0.1. That is: \\127.0.0.1\ - passwordless \\myhost\ - passwordless \\myhost.mydomain.com\ - brings up an authentication dialog Unfortunately, I have a local application trying to resolve UNC paths including the host's FQDN. I've tried resolving myhost.mydomain.com to 127.0.0.1 in both hosts and lmhosts, and calling ping myhost.mydomain.com at the command prompt gives the appearance that this resolution has taken effect; even so, attempting to open \\myhost.mydomain.com\ from Windows Explorer brings up a password prompt, while \\127.0.0.1\ does not. The system is using an OpenDirectory server (Apple's Kerberos+LDAP directory service) for authentication.

  Read the article

• Ping, firewall or DNS issue on Win Server 2008 R2

  - by Fred Kaiser

  I've installed windows server 2008 as a VM for the developers here to work on. Installed SQL Server 2008 as well as IIS7. I am not quite sure why, I can remote into that machine using the name I gave to it (winserverdev) but the guys that are supposed to use the bloody thing can't. One very interesting thing is that I can connect but I can't ping... not the name nor the IP address. Is there anything that I should be looking in order to make it work? Any ideas are welcome. Thanks heaps in advance, I really appreciate it.

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• Blocked connections passing through firewall. What is wrong?

  - by Kiranu

  In our company we have a small business router (Cisco RV082) on which we are using its standard configuration (block all incoming traffic). We also have an SMTP relay configured (using WS2008R2) so that our internal applications can send email through google apps (which requires authentication). The thing is that the server was being used to send spam. We fixed the problem by only allowing the server to relay email from our internal IP address range (10.0.0.0/16). My concern is that there was a way by which external IPs connected to the network and that underlying problem has not been fixed, but I cannot imagine how these machines connected. Any thoughts?

  Read the article

• VirtualBox "Bridged Adapter" when host NIC is turned off

  - by chris_l

  Hi, I'm running Linux (Debian Etch) in a VirtualBox VM on my MacBook. I usually ssh from my Mac terminal to the guest machine. I also want to access the internet from my guest, so I set up my host's WLAN card (en1) as a bridged adapter for eth0 on the client. This works fine, but when I turn off the WLAN card (e.g. to reduce battery consumption), I'd still like to ssh from my host to the guest. This fails of course, because en1 loses its IP address. Is a bridged adapter the best option for what I want to do? How can I make it work? (A simple "ifconfig en1 add 10.0.0.4" didn't do the trick...) Thanks Chris

  Read the article

• Source of Unexplained Requests in Server Logs

  - by Synetech inc.

  Hi, I am baffled by some entries in my server logs, specifically the web-server logs. Other than normal, expected traffic, I have noticed three types of request errors (eg 404, etc.): Broken links, ie links from old, external pages that point to pages that are no longer here Sequences of probes, ie some jerk trying to hack in by scanning my server for a series of exploitable admin type pages and such What appear to be completely random requests for things that have never existed on the server or even have anything to do with the server, and appear by themselves (ie not a series of requests like the probes) Could it somehow be a mistyped URL or IP? That’s about the only thing that I can think of, but still, how could I get a request on say, foobar.dyndns.org (12.34.56.78) for something like www.wantsfly.com/prx2.php or /MNG/LIVE or http://ant.dsabuse.com/abc.php?auth=45V456b09m&strPassword=X%5BMTR__CBZ%40VA&nLoginId=43. (Those are a few actual requests from my logs.) Can someone please explain scenario three to me? Thanks.

  Read the article

• How can I keep websites from knowing where I live?

  - by D Connors

  This questions is related to issues and practicality, not security. I live in Brazil and, apparently, every single website I visit knows about it. Usually that's ok, but there are quite a few sites that don't make use of that information adequately. For instance: Bing keeps thinking that brazilian pages are way more relevant to me than american ones (which they're not). Google.com always redirects me to google.com.br. Microsoft automatically sends me to horribly translated support pages in portuguese (which would just be easier to read in english). These are just a few examples. Usually it's stuff I can live with (or work around), but some of them are just plain irritating. I have geolocation disabled in firefox, so I guess they're either getting this information from my IP or from windows itself (which I bought here). Is there a way to avoid this? Either tell them nothing or make them think I live somewhere else? Thanks

  Read the article

• SSL Certificate for local web server

  - by Firefly

  Is it at all possible to create a self-signed certificate for use on multiple machines on a local network which would stop the browser complaining it is not a trusted site? We have a product which is basically a computer running lighttpd to serve a web interface for configuring the computer (sort of how a router has a web interface). There can also be many of these machines running on the same network with dynamic IP's. What I basically want to do is enable SSL for extra security but I don't want people who are on the local network to be given a browser warning about the certificate not being trusted. Is this at all possible?

  Read the article

• connect to a machine inside the intranet from outside with same address used inside

  - by pietrosld

  Hi all! I have a server inside my intranet, in wich i have apache running with some web applications. when i'm at office the url i use to connect is zeus.mydomain.it, it works couse i have in my /etc/hosts a record 192.168.0.11 zeus.mydomain.it, but obviously it does not work when i'm outside in different network. i have a internet connectino with static ip, so i can connect to my intranet form outside. the question is: how can i connect to the intranet server using zeus.mydomain.it from inside and from outside my intranet ? thanks!! Pietro.

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• How to address an EC2 instance from both inside and outside datacenter?

  - by Alexandr Kurilin

  I'm trying to find a good way of being able to address my EC2 database instance from both inside and outside of the datacenter. Other EC2 instances need to be able to call into it, and other clients like pgAdmin might need to connect to it from the outside world as well. It's my understanding that using the internal and external DNS names is sustainable long term as each reboot leads to a change. I'm thinking of associating an Elastic IP with the instance and giving it an A record (say db1.mydomain.com) which I then will use both within and outside the datacenter. Further instances in the same role will get the same treatment and a DNS record of db2.mydomain.com etc. Now, is there a cleaner and more stable way of achieving this result? Am going about this the wrong way? Suggestions?

  Read the article

• Timeouts when connecting to SQL Server since installing SP1 for Windows 7

  - by Julien

  Hi, I just installed SP1 for windows 7 and I have severe performance degradation when connecting to SQL Server 2005 since then. Establishing connection takes more than 30 seconds while it's instantaneous on another computer. Firewall is disabled and I didn't make any change to the configuration. It happens both when trying to connect with a hostname and with an ip address. Everything else seems to be fine (for instance, I'm have no issue connecting to other computers with remote desktop) What can cause such a problem? Thanks in advance! Edit : uninstalling the SP1 solves the issue instantly.

  Read the article

• How to troubleshoot ping request time out

  - by user28317

  I have a Windows 7 and an XP machine connected to a NETGEAR wireless router. Both machines can log into the network and surf the web. Both are connecting wirelessly. I can ping the router from each machine and get a reply. I can ping each machine from the router and get a reply. But i cannot ping each machine from the other; getting a request time out. Subnet IP Addresses are 192.168.1.* Router =1; Win7 = 10; XP = 11; Firewall is currently off in both systems. Since i can ping from router im picking that not the problem anyway. If i try to ping from xp to win7 i get Request Timed Out. If i try to ping from Win7 to Xp i get destination host unreachable. What should i do now? Thanks

  Read the article

• Computers "applying computer settings" for a long time on start-up...why?

  - by tombull89

  Hello. Might be a bit of a slong shot but I'm stumped, along with the ICT Manager for the school I'm working it. In one of the IT rooms when you switch a computer on it will boot through BIOS fine, but when it gets to "applying computer settings" it can hang for a long time (~15 minutes). If you unplug the computer from the network it starts up fine, gets to the login screen, then you can plug the network cable in and it will work fine. I don't think it's anything to do with the fact we've been coming close to running out of IP addresses or a problem with our DHCP. Microsoft KB says apply the latest service pack, which we've done, and check a service. Servers and domian controllers are S2003, Computers and Desktops are XP. Does anybody have any thoughts on what to try?

  Read the article

• SQL Server Configuration Manager menu won't show up

  - by Aurelien Gasser

  I'm running a Windows 8 VM on a MacBook using Parallels Desktop 9. On this Windows VM, I have a SQL Server instance running perfectly. However, when I launch SQL Server Configuration Manager, and I want to enable an IP configuration, the Enable menu options are invisible : Here is a screenshot : http://i.imgur.com/PY7qGup.png (I don't have enough reputation to display the image inline) When I click the arrow, a contextual menu should appear with 2 choices "Yes" or "No". Instead, a tiny contextual menu appears, but it's empty. I tried using my keyboard tab/space/arrows keys without success. Has anyone faced/solved the same problem ?

  Read the article

• Outlook Anywhere remote https connection issue

  - by holian

  We have SBS 2003, and we use DYNDNS. We forward dyndns address 443 to local server ip 443 port. mycompany.dyndns.org:443 -- server.mycompany.local:443 In android phone i can check my mails with Outlook Active Snyc. From remote machine i can check my mails in owa (https://mycompany.dyndns.org/exchange) But i can't set up outlook 2013 to remote connect. I installed server.mycompany.local to remote machine trusted cert container, but i got error message: "There is a problem with the proxy server's security certificate. The name on the security certificate is invalid or does not match the name of the target site. Outlook is unable to connect to the proxy server. (Error Code 10)" Is it possible to connect exchange, via dnydns? Whats the problem? Thank you

  Read the article

• How to set up Aptana Studio 3 with a Bitbucket private repo

  - by Titus

  I have just started playing around with Git and would like to push a personal project to a newly created, private repo on Bitbucket using Aptana Studio 3. I tried to use the Git integration in Aptana but I couldn't figure out where to enter my username and password for Bitbucket anywhere. I tried using the Team > Share Project context menu but that keeps throwing the following message: Warning: Permanently added the RSA host key for IP address '207.223.240.181' to the list of known hosts. Permission denied (publickey). fatal: The remote end hung up unexpectedly I'm pretty sure that's because my repo is private. However, I couldn't find a provision to provide any form of credentials for linking to a private repo. Any ideas?

  Read the article

• Setting up wifi router as a switch for Internet Connection Sharing

  - by William C

  Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

  Read the article

• Sendmail /etc/hosts and DNS ... what is the correct way?

  - by ben

  I found one tutorial on setting up sendmail that says that in the /etc/hosts file, "The entry for 127.0.0.1 must always be followed by the fully qualified domain name (FQDN) of the server." Like so: 127.0.0.1 bigboy.my-site.com localhost.localdomain localhost bigboy (This tutorial is here). However, I can't find anyone else suggesting something like that. instead most people seem to put some combination of localhost and localdomain.localhost after 127.0.0.1, and then some variant of the fully qualified domain name after the public ip address. What is the correct way?

  Read the article

• Bind dns server in Solaris 10 and win xp clients

  - by stevecomptech

  Hi, Added this in zone db file, i am running solaris 10 _ldap._tcp.mydomain.com. SRV 0 0 389 dc.mydomain.com. _kerberos._tcp.mydomain.com. SRV 0 0 88 dc.mydomain.com. _ldap._tcp.dc._msdcs.mydomain.com. SRV 0 0 389 dc.mydomain.com. _kerberos._tcp.dc._msdcs.mydomain.com. SRV 0 0 88 host.mydomain.com. Now i get this error when i try to join win xp to the domain The query was for the SRV record for _ldap._tcp.dc._msdcs.mydomain.com The following domain controllers were identified by the query: host.mydomain.com Common causes of this error include: Host (A) records that map the name of the domain controller to its IP addresses are missing or contain incorrect addresses. Domain controllers registered in DNS are not connected to the network or are not running. What do i need to change in order my win xp join the domain

  Read the article

• No DNS resolving with VPN (RRAS)

  - by Sven

  I have a RRAS server setup on a Windows 2003 machine with two NIC's. The VPN works like a charm, I can ping all the other computers on the network. But it fails when I try to access resources with hostnames. I searches for a solution but the ones I found are about RRAS setup with a remote DHCP server. But in my case it's the RRAS server that hands out the ip addresses (option for redirection for WINS, DNS is ON and set to the LAN NIC). I also heard something about FQDN.. but I don't really understand what that is.

  Read the article

< Previous Page | 310 311 312 313 314 315 316 317 318 319 320 321  | Next Page >