Search Results

Search found 18341 results on 734 pages for 'neural network'.

Page 318/734 | < Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• How can I connect to my Airport Extreme Shared Disk using Windows?

  - by matt ryan

  I have a shared disk attached to my Airport Extreme, which I can connect to remotely in OS X through the finder via command - k, and entering in the proper address: afp://test.dyndns.org:1111 1111 being the port I've reserved for the disk in the AE port mapping. This is such a great feature, but I don't always have access to a Mac. My question is how can I connect to this drive via Windows XP? Please note, that the shared drive is a Drobo FS and formatted to handle both Windows and Mac OS. I've tried mapping a network drive via My Computer - Tools - Map Network Drive and entering: \\test.dyndns.org:1111\Drobo-Name I've also tried Start - Run and entering the same, both with and without the port #.

  Read the article

• Connected to internet but can't browse after trying to remove Covenant Eyes

  - by Joanna

  I recently got a MacBook Pro. It connects to ethernet\wifi and has internet but when I open Safari or Firefox, nothing happens. I get a timeout for all websites. I had Covenant Eyes on my Mac before and tried to remove it. My friends who work with computers have tried everything (ping, nslookup etc). Network diagnostics show no problems I can see I'm connected through ifconfig because I get an IP. I also get a response pinging www.google.gr. There are no proxies set in my Network preferences. Any ideas?

  Read the article

• RDP failing due to Audit Failure on the IPSec driver

  - by paulwhit

  I am trying to RDP into a Windows 7 Hyper-V image connected to a corporate network that publishes IPSec policies via Active Directory. I am seeing this error in the log: IPsec dropped an inbound clear text packet that should have been secured. If the remote computer is configured with a Request Outbound IPsec policy, this might be benign and expected. This can also be caused by the remote computer changing its IPsec policy without informing this computer. This could also be a spoofing attack attempt. Remote Network Address: XXX.XXX.XXX.XXX Inbound SA SPI: 0 How do I change my settings on the computer using RDP to something suitable for the domain-joined Hyper-V image?

  Read the article

• Is there no such thing as a Gigabit switch?

  - by Torben Gundtofte-Bruun

  According to the manufacturer specification, even my rather plain desktop computer has "Gigabit Ethernet". So when I want to copy large files over the LAN (not Internet) it would make sense to have a gigabit switch. I'm searching eBay for a gigabit switch for a planned home network upgrade. The products I find are all labeled "gigabit" but they all have 24 x 10/100Mbit autosensing ports and sometimes 2 x 10/100/1000Mbit autosensing ports. It was my understanding that 10/100 is ancient and that modern computers have network interfaces that work with 1000Mbit, so it would make sense to get a switch that has 24 x 1000Mbit ports. Did I misunderstand, or are sellers (deliberately?) mislabeling older hardware? (Let's not dive into wired vs. wireless networks and how "N" wireless is fast. You'd be right, but not answering the question.)

  Read the article

• SQL2008 Won't Work After SP1 Install?

  - by leen3o

  I have SQL2008 installed on my Win2008 server, and its been working fine - I have sites running using SQL databases etc.. I thought I would install SQL2008 SP1, but after install I cannot connect to SQL via Management Studio, and in configuration manager I cannot start SQL? TITLE: Connect to Server Cannot connect to #MYINSTANCENAME#. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=-1&LinkId=20476 BUTTONS: OK I'm not really a techie so a bit stuck?? any ideas??

  Read the article

• wireshark not seeing all packets on WiFi

  - by Caffeine Coma

  I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

  Read the article

• There's IP but can't reach gateway

  - by icky

  I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

  Read the article

• How can I use my laptop's monitor as my PC's ONLY monitor? [closed]

  - by Randell

  Possible Duplicate: Can I use my laptop as a second monitor for my desk computer? My PC's monitor just died and I'm not looking at buying a new monitor anytime soon. So I'm thinking of using my laptop's monitor for it. Both machines are running on Fedora linux. Edit: Both machines are connected to the same wireless network. PC needs to log in before it can connect to the network if I'm not mistaken. Update: This is different from Can I use my laptop as a second monitor for my desk computer? , because that question is asking how to use the laptop screen as the secondary display, not as the only display.

  Read the article

• Airport Express chokes Wi-Fi for a few seconds, several times per hour. Any idea why?

  - by user13727

  I'm using a MacBookPro connected to an AiportExpress' Wi-FI network. Every once in a while, the Wi-Fi will choke up and either drop some packets, or lag horribly for several seconds. I'm losing hair over this because every time I chat on Skype, the call hangs randomly due to this problem. Any idea what's wrong? Some more details: two networks are set up: 2.4Ghz and 5Ghz, and the issue happens on both the network uses WPA2 Personal for security the Airport is in the same room with my computer the Airport is fairly new, bought this summer, model number off the back: A1392 tried connecting to a neighbours wifi to see if it's a problem with my computer, or interference. It's not, it doesn't happen on their network. tried resetting it several times tried changing channels manually Ping results are below, so you can see what I'm talking about. EDIT: 10.0.1.1 is the Airport's IP 64 bytes from 10.0.1.1: icmp_seq=1795 ttl=255 time=0.813 ms 64 bytes from 10.0.1.1: icmp_seq=1796 ttl=255 time=3.335 ms 64 bytes from 10.0.1.1: icmp_seq=1797 ttl=255 time=3.403 ms 64 bytes from 10.0.1.1: icmp_seq=1798 ttl=255 time=3.414 ms 64 bytes from 10.0.1.1: icmp_seq=1799 ttl=255 time=3.227 ms 64 bytes from 10.0.1.1: icmp_seq=1800 ttl=255 time=3.274 ms 64 bytes from 10.0.1.1: icmp_seq=1801 ttl=255 time=3.253 ms 64 bytes from 10.0.1.1: icmp_seq=1802 ttl=255 time=3.292 ms >>>> choke starts <<< 64 bytes from 10.0.1.1: icmp_seq=1803 ttl=255 time=53.977 ms 64 bytes from 10.0.1.1: icmp_seq=1804 ttl=255 time=35.049 ms 64 bytes from 10.0.1.1: icmp_seq=1805 ttl=255 time=19.820 ms >>>> choke ends <<< 64 bytes from 10.0.1.1: icmp_seq=1806 ttl=255 time=0.716 ms 64 bytes from 10.0.1.1: icmp_seq=1807 ttl=255 time=0.705 ms 64 bytes from 10.0.1.1: icmp_seq=1808 ttl=255 time=0.919 ms 64 bytes from 10.0.1.1: icmp_seq=1809 ttl=255 time=0.659 ms 64 bytes from 10.0.1.1: icmp_seq=1810 ttl=255 time=0.877 ms 64 bytes from 10.0.1.1: icmp_seq=1811 ttl=255 time=0.679 ms 64 bytes from 10.0.1.1: icmp_seq=1812 ttl=255 time=0.854 ms 64 bytes from 10.0.1.1: icmp_seq=1813 ttl=255 time=0.644 ms 64 bytes from 10.0.1.1: icmp_seq=1814 ttl=255 time=3.779 ms ... time passes .. 64 bytes from 10.0.1.1: icmp_seq=1599 ttl=255 time=0.674 ms 64 bytes from 10.0.1.1: icmp_seq=1600 ttl=255 time=0.930 ms 64 bytes from 10.0.1.1: icmp_seq=1601 ttl=255 time=0.665 ms 64 bytes from 10.0.1.1: icmp_seq=1602 ttl=255 time=1.085 ms Request timeout for icmp_seq 1603 Request timeout for icmp_seq 1604 64 bytes from 10.0.1.1: icmp_seq=1605 ttl=255 time=104.969 ms 64 bytes from 10.0.1.1: icmp_seq=1606 ttl=255 time=11.521 ms 64 bytes from 10.0.1.1: icmp_seq=1607 ttl=255 time=0.926 ms 64 bytes from 10.0.1.1: icmp_seq=1608 ttl=255 time=0.993 ms 64 bytes from 10.0.1.1: icmp_seq=1609 ttl=255 time=0.745 ms And the Signal-Noise ratio:

  Read the article

• Allow users to view Word documents only and not be able to edit, copy or save them.

  - by Alexander

  Hello In a traditional Windows Server 2003 environment with AD, we have shared a folder for our policy documents (MS Word). These documents get edited/updated now and then by the administrator(principal of college). Users only have read-only access to the folder, but they can still save-as and then change the content. Sharepoint is a possible solution but not easy to implement. We also thought of using a CMS on Linux and installing Joomla to let users only view the docs with a document management system... but is it possible to automatically retrieve the policy folder on the network and convert or put it in a format that users can only view and not copy? We also thought of saving the docs to secure pdf format but the principal wants an automated system. Basically she just wants to work in Word and the policies must be available to staff members on the network. Any ideas? Much appreciated.

  Read the article

• Add a hook to run when NetworkManager connects

  - by rplevy

  What would be a good way to make a script run every time my computer connects to the network in Ubuntu? Would I somehow use dbus to do this? Background: when I'm on the train I run a short Perl script to click a button on the splash page. That way I can immediately use the internet without having to manually visit a pointless website. My script is a near-perfect solution, but it would be perfect if it could run automatically any time I connect to the network.

  Read the article

• Where are Wireless Profiles stored in Ubuntu

  - by LonnieBest

  Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

  Read the article

• nodejs server hanging from time to time

  - by Johann Philipp Strathausen

  I have a node server (0.6.6) running an Express application, along with Mongoose and s3, on an Ubuntu 11.04 machine. Several times per hour, the server is hanging. That means that the application is working fine, I see the express loggings, and then all of a sudden the server stops responding. No errors, no traces, no loggings, and strangely enough the browser won't show the request even in the network debugging window. From any machine in the local network it's the same behaviour. I restart the server and it's okay again for several minutes, then again starts to hang, everytime while doing something different. The same application on Amazon on the same Ubuntu version works fine and never hangs. I know all this is kind of vague, but I don't know where to start. Has any of you seen something like this before? Any idea?

  Read the article

• Uploading with browser makes all other browser tabs and devices disconnect

  - by fabsenet

  Whenever I upload a video to YouTube all other browser tabs behave like there is no connection at all. It even affects my phone and other computers on the network therefor I think it has to do with my router. When the upload is done everything works normally again. I never observed this behavior with any other upload. My router is a Fritz!Box 7390 and my uploading PC is connected through a 1000mb/s switch (wired) to the router. Uploading through another browser does not change anything. I understand that other sites become slow as the network resources are limited, but stopping altogether feels wrong. speed.io measures for my internet connection: 40.894 Kbit/s down, 2.685 Kbit/s up, 29 ms ping, 2.048 con/m connects

  Read the article

• ASA and cisco vs NSA sonic firewall

  - by Lbaker101

  Currently I’m trying to structure our network to fully support and be redundant with BGP/Multi homing. Our current company size is 40 employees but the major part of that is our Development department. We are a software company and continued connection to the internet is a requirement as 90% of work stops when the net goes down. The only thing hosted on site (that needs to remain up) is our exchange server. Right now i'm faced with 2 different directions and was wondering if I could get your opinions on this. We will have 2 ISPs that are both 20meg up/down and dedicated fiber (so 40megs combined). This is handed off as an Ethernet cable into our server room. ISP#1 first digital ISP#2 CenturyLink we currently have 2x ASA5505s but the 2nd one is not in use. It was there to be a failover and it just needs the security+ license to be matched with the primary device. But this depends on the network structure. I have been looking into the hardware that would be required to be fully redundant and I found that we will either of the following. 2x Cisco 2921+ series routers with failover licenses. They will go in front of the ASAs and either connects in a failover state or 1 ISP into each of the 2921 series routers and then 1 line into each of the ASAs (thus all 4 hardware components will be used actively). So 2x Cisco 2921+ series routers 2x Cisco ASA5505 firewalls The other route 2x SonicWalls NSA2400MX series. 1 primary and the secondary will be in a failover state. This will remove the ASAs from the network and be about 2k cheaper than the cisco route. This also brings down the points of failure because it’s just the 2x sonicwalls It will also allow us to scale all the way up to 200-400 users (depending on their configuration). This also makes so the Sonic walls. So the real question is with the added functionality ect of the sonicwall is there a point in paying so much more to stay the cisco route? Thanks!

  Read the article

• SOA &amp; Application Grid Specialization&ndash; Education Implementation Assessment - Step 4 of 6

  - by Jürgen Kress

    In our first step to become SOA Specialized & Application Grid Specialized we highlighted the OMM system to register your opportunities. In our second step we featured marketing activities to create your reference cases and run joint marketing campaigns. In the third step we focused on the competence center assessments SOA Sales assessment & SOA Pre-Sales assessment & Support assessment / Application Grid Sales assessment & Application Grid Pre-Sales assessment & Support assessment In the forth step we will focus on the education implementation assessment criteria: · Oracle Application Grid Certified Implementation Specialist · Oracle Service-Oriented Architecture Certified Implementation Specialist Bootcamp training steps (optional): Login to Oracle Partner Network (support for login contact Partner Business Centers) Attend a SOA or Application Grid bootcamp to learn the product hands-on Find a training close to your location in the local training calendar Pearsonvue Steps: Go to http://www.pearsonvue.com/Oracle/ ·Create a web account. (will take up to 24 hours) if you need your OPN Company ID (please contact Partner Business Centers) ·Register and attend the Oracle Service-Oriented Architecture Certified Implementation Specialist (1Z1-451) or Oracle Application Grid Certified Implementation Specialist  (1Z1-523) at a training center close to you. The Application Grid Specialized is in beta phase, therefore we give away free vouchers; please contact Jürgen Kress if you like to get one. ·Submit your successful exam If you need to get an Oracle Partner Network Account please contact our Partner Business Centers. For more information on Specialization please visit our OPN Specialized Webcast Series and become a member in our SOA Partner Community for registration please visit www.oracle.com/goto/ema/soa Jürgen Kress, SOA Partner Adoption EMEA Thanks for your efforts to become Specialized! Technorati Tags: soa specialization

  Read the article

• Java Road Trip: Code to Coast (#javaroadtrip)

  - by Justin Kestelyn

  Hey, have you heard? The Java Road Trip bus may be stopping at a city near you this summer, starting June 14. And your peeps at Oracle Technology Network have donated some goodies. What is the Java Road Trip? Basically, we have packed a rock-star bus with demos (Java FX, Oracle ADF, Java EE 6, JDK 7, GlassFish, Java ME) and are putting it on the road; it will make 20 stops across the U.S. in the next couple of months (and MAY may make a special appearance at JavaOne, if we can find a big enough parking space). In many cases these stops will coincide with Java or Oracle user group meet-ups and will always involve beer, food, and free stuff. Furthermore, engineers from HQ will be flying out at various times to rendezvous with these meet-ups and answer your questions. Also, because this tour will only reach a relatively small number of people, we're working hard to provide a virtual experience: there will be a blogger/videographer/photog/tweeter on board, reporting on its every move. You'll find all this content at java.com/roadtrip, and you can get real-time updates via @java. And this new update: If you're attending ODTUG Kaleidoscope in Washington, D.C., in late June, you'll get a chance to see the Java Bus in all its glory. And don't forget your t-shirt, cup, and screen cleaner, all provided by Oracle Technology Network.

  Read the article

• apt-get issue after upgrading to 12.04

  - by user83906

  I have recently upgraded my cluster from 11.10 to 12.04. After the upgrade, I am having trouble running apt-get on the cluster nodes. I can ssh between the nodes (client-to-client; client-to-head; client-to-external etc.). However, sudo apt-get update produces the following errors: Ign http://us.archive.ubuntu.com precise InRelease Ign http://security.ubuntu.com precise-security InRelease Ign http://www.openfoam.org maverick InRelease Ign http://us.archive.ubuntu.com precise-updates InRelease Err http://security.ubuntu.com precise-security Release.gpg Something wicked happened resolving 'security.ubuntu.com:http' (-5 - No address associated with hostname) Err http://www.openfoam.org maverick Release.gpg Something wicked happened resolving 'www.openfoam.org:http' (-5 - No address associated with hostname) Ign http://us.archive.ubuntu.com precise-backports InRelease Ign http://www.openfoam.org maverick Release Ign http://security.ubuntu.com precise-security Release Err http://us.archive.ubuntu.com precise Release.gpg Something wicked happened resolving 'us.archive.ubuntu.com:http' (-5 - No address associated with hostname) Ign http://security.ubuntu.com precise-security/main Sources/DiffIndex Err http://us.archive.ubuntu.com precise-updates Release.gpg Something wicked happened resolving 'us.archive.ubuntu.com:http' (-5 - No address associated with hostname) Ign http://security.ubuntu.com precise-security/restricted Sources/DiffIndex 15% [Connecting to us.archive.ubuntu.com] [Connecting to security.ubuntu.com] [Connecting to www.openfoam.org] On the headnode, I have in /etc/network/iterfaces: auto eth0 iface eth0 inet static address 192.168.0.1/24 On the client nodes, I have /etc/network/iterfaces: auto eth0 iface eth0 inet static address 192.168.0.101 netmask 255.255.255.0 gateway 192.168.0.1 Please advise.

  Read the article

• Windows Server 2008 R2 DNS Server not working?

  - by wolfvilleian

  I have a server running Windows Server 2008 R2 hosting a DNS server, exchange 2010 and is a domain controller. One computer on the network (and domain) can ping the server 25% of the time, also when I try to ping it's own hostname it also does not work. However another computer that is on the domain can ping it fine, and another computer on the network but not domain can ping fine as well. The computer that cannot ping the server is setup to use the DNS server running on the server only (secondary dns points to nothing) and it will resolve the hostname of the server to the external IP not internal when the other two computers correctly resolve the internal All 3 computers and server are connected directly into the same switch. Does anyone have any ideas on how to fix this? Thanks

  Read the article

• Debian: Firefox or Iceweasel default printer for POS station

  - by Bubnoff

  Context Using Debian 6.04 "Squeeze" as POS station. There are two printers installed: Network printer and a receipt printer It absolutely must be able to print by default to the receipt printer on a certain website though the system default is a network printer. In Debian ...it doesn't. Problem I've set up XP, 7, Ubuntu and even Mac OSX this way, so I'm no stranger to setting Firefox up this way ...same Iceweasel/Firefox settings ...complete fail. Always uses system default no matter what the settings, or, which printer you print from. To get this to work on other systems you do this: Print a page in Firefox using desired printer. Ensure print.save_settings is true. Firefox remembers last printer used Set print.always_print_silent = true The end. This works on every OS I've set up ....except Firefox and Iceweasel in Debian. My only recourse seems to be to set the receipt printer as default or go back to bloaty Ubuntu/Mint ...etc.

  Read the article

• CloudMail

  - by kaleidoscope

  In Web Applications, we often come across requirement of sending and receiving emails through our application. So same can be for the applications hosted on Azure. So Do you want to send email from an application hosted on Azure? CloudMail is one of the possible answers. CloudMail is designed to provide a small, effective and reliable solution for sending email from the Azure platform directly addressing several problems that application developers face. Microsoft does not provide an SMTP Gateway (yet) so the application is forced to connect directly to one hosted somewhere else, on another network. So to implement such functionality one of the possible option is using Free email providers. This might be fine for testing, but do you really want to rely on a free service in production? There can be other issues with this approach like if your chosen SMTP gateway is down or there are connection problems? Again there can be some specific requirement that, you want to send email via a company’s mail server, from inside their firewall. CloudMail solves these problems by providing a small client library that you can use in your solution to send emails from you application and a Windows Service that you run inside your companies network that acts as a relay. Because the send and relay are disconnected there are no lost emails and you can send from your own SMTP Gateway.   CloudMail is in its Beta version and available for download here.   Technorati Tags: Geeta,Azure Email,CloudMail

  Read the article

• Forwarding wifi traffic to wired pc

  - by brydgesk

  I'm trying to play around with Wireshark on my home network, and was wondering if there is a way to create a new connection on my PC that receives all wifi packets on the network. The PC is a wired Windows 7 machine, and I'm using DD-WRT on an Asus RT-N16 router. I'm not trying to hack anything, I have full admin access to the router itself. My searching has led me to articles about client bridges and repeater bridges, but none of them seemed to apply entirely to my situation. I'd like to continue using my standard wifi connection, but make my PC act as a repeater that receives all wifi traffic. Again, the PC has no wireless connection. I've used tcpdump which is installed on the router itself, but I'd be more comfortable analyzing the packets in Windows, as I'm trying to learn Wireshark. Thanks

  Read the article

• Which freeware can mount ISOs on Windows 7

  - by Daniel

  WinCDEmu failes (does not work, Windows can not be rebootet anymore) Phantom CD failes (cannot mount from network share) Does an alternative exist?

  Read the article

• Remote Desktop Connection over VPN on mac

  - by Diego Faria

  I'm trying to connect to a Windows computer on over a VPN connection using Remote Desktop connection. I opened Network on mac and created a new connection. Interface: VPN. VPN Type: PPTP. I filled the inputs for server address, account name, password and applied. I connect the VPN and it connects. I open Remote Desktop Connection and put the IP of the machina i want to connect but it dont connect, a problem occurs saying that the machina may be turned off and etc. But in a windows machine I can connect there and the machine is up and running. On my mac I ping to the ip address that a want to connect and it has no response. I think that the vpn have a problem, is there a way for me to certificate that i am on the vpn network ? Whats going on?

  Read the article

< Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >