Search Results

Search found 8850 results on 354 pages for 'xp'.

Page 320/354 | < Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >

  • disk write cache buffer and separate power supply

    - by HugoRune
    Windows has a setting to turn off the write-cache buffer (see image) Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. Is it feasible and economical to get such a "separate power supply" for the internal sata drives of a non-server PC? Under what name is such a power supply sold? I know that there are UPS devices that can be connected to external drives,but what is required to be able to switch this setting safely on for an internal disk? The setting has different descriptions in different version of windows Windows XP: Enable write caching on the disk This setting enables write caching in Windows to improve disk performance, but a power outage or equipment failure might result in data loss or corruption. Windows Server 2003: Enable write caching on the disk Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows Vista: Enable advanced performance Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows 7 and 8: Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. This article by Raymond Chen has some more detailed information about what the setting does.

    Read the article

  • Gigabit network limited to 25MB/s by CPU. How to make it faster?

    - by netvope
    I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

    Read the article

  • Multiple copies off the same printer on Windows 7 from PrintUIEntry

    - by Kev
    I currently have a number of bat files which work perfectly fine on Windows XP which install the same printer multiple times with a number of finisher options set - e.g. after running the bat file below I would end up with four printers in the printer drop down called Sharp Kits Printer - A4 Single Sided Sharp Kits Printer - A4 Single Sided Stapled Sharp Kits Printer - A4 Duplex Stapled Sharp Kits Printer - A4 Duplex which all have there options configured in the relevant way. I have amended on Windows 7 to point to correct INF file and printer name in the INF files - a single printer installs fine. However when I run the complete batch file only the first printer in it is installed - occassionally the later ones flash up in the GUI but then vanish when you press F5 and are still missing after a reboot. SET QUEUENAME=http://192.168.7.123:631/printers/Sharp700 SET PPD=J:\DRIVERS\Printers\MX700-Win7-64\SJ1JWENG.INF SET PPDENTRYNAME=SHARP MX-M700U PPD J: cd "\DRIVERS\Printers\MX700-Win7-64" SET NICENAME="Sharp Kits Printer - A4 Single Sided" SET PREFS="J:\SCRIPTS\Printers-Win7-64bit\Sharp_SINGLE_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... SET NICENAME="Sharp Kits Printer - A4 Duplex" SET PREFS="J:\SCRIPTS\Printers\Sharp_DUPLEX_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... I have tried adding the "/u" paramater to the end, I have changed the "/n" paramater to be different (e.g. n1, n2,n3 etc) - both of these result in the same. I have also tried to change the port (/r) to have "_1" (etc) on the end like the GUI would but this errors as the port doesn't exist. Is it possible to do this on Windows 7, and if so how?

    Read the article

  • How can I create a separate toolbar from the Task Bar?

    - by Iszi
    In Windows XP, you could separate toolbars from the Task Bar by dragging them to the desktop. They could then be left lying about anywhere on your screen or, my preferred option, docked to any side of the screen. I found this particularly useful to keep a handy list of common phone numbers quickly accessible. I'd create a new toolbar pointing to a custom folder, and put a bunch of dead shortcuts in the folder that had names and numbers as their file names. I'd then dock the toolbar to the left side, set it to auto-hide and always on top (options which could be set separate from the Task Bar as well) and it would be readily available no matter what else I was doing on my system. However, on my Windows 7 system, I seem unable to perform the crucial step of pulling the new toolbar off of the Task Bar. This is of course with the Task Bar "unlocked" so that I can move all my toolbars around. Is there something I'm missing here, or is this a feature that's been disabled in Windows 7? Is there any way to re-enable it, or otherwise achieve similar functionality? I'd rather be able to do this without additional software, if possible.

    Read the article

  • Revamping an old and unstable office IT-solution using Windows Server and OpenVPN

    - by cmbrnt
    I've been given the cumbersome task to totally redo the IT-infrastructure for a customer's office. They are currently running Windows XP all over, with one computer acting as a file server with no control over which users have access to which files, and so on. To top it off, this file server also functions as a workstation, which means it gets rebooted every time the user notices some sluggish behavior or experiences problems with flash games. To say the least, this isn't working for them. Now - I've got a very slim budget, but I need to set up a new server, and I wish to run Windows Server 2008 on it. I also need the ability to access the network remotely via VPN. Would it be a good idea to install VMware ESXi 4.1 onto the new server, and then run Windows Server 2008 as well as a separate Debian install for openvpn on it? I don't like the Domain Controller for the future AD to also run a VPN-server, because of stability issues when something goes to hell with either of them. There will be no redundancy though. However, I'm not sure if there is something to gain by installing a VPN solution on the Windows Server itself, when it comes to accessing file shares on the network via VPN. I don't know how to enable users logging in via the VPN to access the remote files, since they will be accessing the network from their own home computers (which is indeed a really bad idea, but this is what I've got to work with). They won't be logged in to the windows Domain, but rather their home workgroups. I need to be able to grant access to files in certain directories based on the logged in AD-user, but every computer won't necessarily be configured to log into the domain. I'm not sure how to explain this in a good way, but I'd be happy to clarify if somethings not clear. Any help would be great, because I've got a feeling that I can't do this without introducing a bunch of costly new rules when it comes to their IT-solution. I'd rather leave that untouched and go on my merry way to the next assignment.

    Read the article

  • Linux file server for an inexperienced admin

    - by Pat
    A charity I volunteer for wants a file server for their mostly Windows machines (about five XP and 7 machines, with some Mac laptops every now and then). For the server, I have a PC with an Intel Core 2 Duo 3GHz proc, 4GB of DDR2 400MHz RAM, and a 500 GB HDD. (I should point out that they do not currently have any server - they are just using Windows to share a folder on one of the PCs.) What is a linux distro that is easy to configure for Windows file serving yet stable and secure enough to protect sensitive data without an expert sysadmin? I'm guessing that a Debian distro would probably fit the security bill, but I don't know of any tailored to novice sysadmins. Also, are there any killer apps for making this easy to administer and set up (as a Windows file server, in particular - this answer is a good example)? Would FreeNAS be sufficient? Once it's all set up, what are the minimum measures I need to take to keep the data secure? I found this somewhat helpful answer, but it's not specific to my question of just getting a secure file server up, running, and maintained.

    Read the article

  • How to disable monitor auto detection in Windows 7?

    - by Jay Yother
    I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

    Read the article

  • Chrome Lockups Windows 7 64-bit

    - by Mike Chess
    I'm running Google Chrome (6.0.427.0 dev) on Windows 7 Home Premium 64-bit (AMD Phenom 3.00 GHz, 8 GB RAM). The computer lockups hard after running Chrome for about five minutes. The lockup happens whether Chrome is actually being used to browse web sites or it is just idling. No programs can be started or interacted with when this happens. The computer must be power-cycled to recover. The lockup happens regardless of which web sites are being browsed. The system event logs do not show any events around the time when the lockup transpired. All other applications run just fine on this system. In fact, Chrome ran without issue for several months on this system (the system was brand new 03-2010). I also run the same version of Chrome on other computers (Windows XP SP3) without issue. I've come to really like Chrome and use it as my default browser whenever possible. What could be causing Chrome to cause the system to lockup as it does? Does Chrome have any logs that aren't part of the Windows event log? Does Chrome have a debug command line switch that might reveal more about what happens?

    Read the article

  • Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks.

    - by A302
    Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

    Read the article

  • How to change password on RAR archive w/o modifying arch. files attributes (modified/created)?

    - by Larry78
    How do I change the password of an .RAR archive, without changing the date/time attributes of the files in the archive? Unfortunately you can't directly change the password of the archive with WinRAR, you have to extract the files, and then make a new archive with the new password. So the created/modified attributes of the files in the archive get changed. I know you can manually change the attributes of a file with available utilities - but there are hundreds of files in the archive, each with unique attributes, so it would take a very long time to "fix" each file before re-archiving it. I'm using WinRAR 3.51, the last free version. Windows XP Pro SP3. Update: I don't care if the output is a .RAR file or a ZIP file IZArc4.1 will convert the RAR to a ZIP, and it keeps the dates. The problem is it compresses the file - there isn't a "store" option, and setting the default to store in the main configuration doesn't effect conversions. The RAR contains uncompressed files. None of these other archiving programs will even do a conversion. A couple claim to, or try to, but the errors returned indicate a very lousy application. So far I've tried PeaZip, 7-Zip, FilZip, TugZip, SimplyZipSE, QuickZip, and WinShrink (from downloads.cnet.com). WinRAR gives the error "skipping encryped archive" when I try the conversion. It asks for the password first, and I know it's right, as I opened the archive, and I can read/view all the files in it. It works on non-encrypted files.

    Read the article

  • Nvidia RAID 1 Problem. Degraded drives...

    - by Vedat Kursun
    I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

    Read the article

  • Nvidia RAID 1 Problem. Degraded drives...

    - by Vedat Kursun
    I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

    Read the article

  • How can I create two partitions and clone one to the other (using Clonezilla)?

    - by johnny
    I was hoping someone could help. I want to create a "backup" partition. I want to create two partitions on my drive. One is a good install, which I want to then use clonezilla to copy the good partition to the broken/unused partition and have the restored partition boot up as usual. Example, C: goes bad. D: is a "good" copy of C. C gets a corrupt registry. I restore D to C, C will then boot up as usual. So, I need to do the clone with Clonezilla and the restore with the same. I see the part_...clone and restore. Will this do it? How do I get the partitions? EDIT: I am using XP. How can I do this? Also, I know this is not the best thing for all occasions. I have a offline backup as well. I would like to have both. Thanks for any help. I'm using Clonezilla if it matters.

    Read the article

  • How do I configure IIS to allow access to network resources for PHP scripts?

    - by Dereleased
    I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

    Read the article

  • Windows 7 boot animation slows down startup by default?

    - by kngofwrld
    I just upgraded my HDD to an SSD drive. I am running a completely fresh install and enjoy the short boot time. I tweaked the startup to be as fast as I could by removing unneeded apps and such. Nor am I running a solid desktop background (which causes a 30-sec startup delay). I have a 2.1ghz 64 bit laptop with 4 gigs of ram, so it's not a liquid-cooled speed monster, but I checked some super high end PC boot vids on YouTube and noticed that they startup in almost the same time as my machine. I also noticed that the glowing Windows 7 animation plays all the way no matter how fast the PC is. I turned off the animation, and the startup time is unchanged. I turned on verbose startup info and noticed that it runs until the very end, where it looks like it just sits there for no reason waiting for something to happen for a few seconds. So now I think that the Windows 7 startup animation has a timer built into it that forces the computer to wait for no other reason than to play the full animation. Super-fast XP boot vids on YouTube seem to start much faster (and not just because they "have less to load"). Am I imagining things? My question is: How can I turn off not just the animation, but the timer for the animation. Here is a vid that tipped me off, I have no relation to the poster. (warning: soundtrack might be loud) http://www.youtube.com/watch?v=T5LkX3xejJ4

    Read the article

  • Please help me get rid of asmonitor.exe

    - by LCD Fire
    It might be silly and I trully apologize if the question is not apropriate here, but I have really tried and got to nowhere. I have a windows xp startup error which indicates something about asmonitor.exe program from the ActualSpy keylogger. I had installed but removed ActualSpy keylogger using Superantispyware or something close. I have searched the registries and found a asmonitor entry deleted. I looked at startup programs and can not find the asmonitor program. In addition, I searched the c: drive using regular explorer search and searched using ESET NOD32 antivirus. In each case I cannot find the application... I have even looked at startup programs using msinfo32 command. msconfig-startup NOTHING! it drives me crazy! I can't get rid of it. it is still showing up at windows startup! Where do I find this little program? where is it located? I don't want it to keep showing up. I don't want programs that can do it.. or maybe free ones. But I prefer manual solutions. aren't are any?

    Read the article

  • Onboard Ethernet suddenly stopped working to router

    - by AfterschoolHobbist
    Hey guys, yesterday I have a sudden problem of my Ethernet connection to my router. My computer is a Pendium 4 with Window XP SP3 running on it and it was working fine earlier in the day, but yesterday night was the start of the problem. My computer is unable to ping to the router and to any other website and unable to get internet connection. As beside it was connected to a hub, I directly connected it to the router directly and the same problem occurred, being unable to ping to the router (and connecting to it) and still no internet access. My directly connected to the modem and the problem still persisted. For each connection, I connected it to my computer and my laptop and my laptop was able to connect, while my desktop computer was unable. I wondered if it was a OS issue and ran a live Ubuntu CD to see if Ubuntu was able to connect to the internet, but the issue persisted and I was unable to get internet access. I then set my router's lease time to 1 hour and waited. After 1 hour, the lease for my computer was removed and I hoped this worked, but it didn't work, but something strange is acting up. My desktop computer is still unable to ping to the router or connect to the internet, but for some reason, my router and desktop computer is still able to contact each other by providing a lease of an local ip address. The router record of a lease to my desktop computer, and when I do ipconfig, my desktop also recognize that it has been provided a local ip address. I have concluded that this is a hardware issue and the only solution to fix this is to by a network card adapter, but I am wondering if anyone has any solutions that could explain why this happen, why my mac address is 01-23-45-67-89-ab, and is there any way to fix it without buying a new network card? Thanks in advance.

    Read the article

  • Windows 7 automatically logs out when logging in

    - by Luke
    A Windows 7 HP x64 computer is set to automatically log in (no password), but once it starts logging in, it starts to load the desktop after the welcome screen, but before icons or background images are loaded, it goes to the Welcome screen saying 'Logging Off'. I can log in with Safe Mode, and I ran a couple different virus scans, with no detections. I also tried checking the userinit.exe file in System32 (as suggested by MANY users for Windows XP), but it's the same version as a working system. I also checked the registry under HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon for the SHELL and UserInit values, but they look normal. I tried to disable all startup items (through MSCONFIG) to select Diagnostic boot, but then I get a blue screen about the video driver not loading. Any other ideas? EDIT I created a new user, and it could log in no problems. I am thinking it's the NTUSER.DAT file. I just renamed it to NTUSER.DAT.old, then tried logging in as the problem user. I could log in, but as a TEMP profile. His profile folder is now C:\Users\TEMP, and his old folder is still accessible but in the wrong location. EDIT 2 I can't seem to turn off the TEMP profile, so I'm open to other suggestions. Copying the folders (i.e. Documents, Music, etc) does not work, as it creates an additional TEMP.000 then TEMP.001 folder each time the user logs in.

    Read the article

  • MBR seems to be gone

    - by bobobobo
    So, horror story for everyone. I bought two spanking new HDD's. MM!! Gbitage. I removed all my old HDD's, physically labelled them, and was preparing to install all new HDD's (fresh sys install included!) To make sure what HDD was what, I popped each OLD HDD (data filleD!) into a Thermaltake Blacx toaster.. surprisingly BOTH couldn't be read. I didn't have static on my hands! I'm certain of it. I touched metal, touched wood, before beginning this all. Thinking that was strage, I hauled up the new sys, installed Win XP (of course!) on the new HDD, and now the two OLD HDD's (data filled!) that were entered into the toaster cannot be read. And they had tons of data on them. I read about MBR's being nuked and it sounds like that is what it is. But I'm at a loss what to do. There are so many MBR recovery programs out there, I kind of feel overwhelmed. I don't want to lose my data by just pikcing one, yet it seems so close within reach, I'm not panicking anymore.. Anybody have a play by play that I could follow? I just don't want to spend $900 on data recovery centers if I can do this myself..

    Read the article

  • Remote reboot of windows to knoppix

    - by user64452
    I am attempting to develop an Auditing application. This audit application will be employed on windows networks. The Audit will need to discover Hardware and software details of all machines attached to the network (including Printers) I do not want to have to install this application on each workstation. The audit app. needs to discover all the ip addresses of all the networked workstations. I have been prototyping this app for the last couple of months and have decided to try a new tack Is this possible? a). You have a windows network, min Windows XP sp3 and upwards b). Maximum of 100 Networked machines (if that matters) c). I need to remotely reboot each WINDOWS machine in turn on the entire network and get it to startup using UNIX, say knoppix for example! d). however the knoppix live cd is only available from one of the networked machines Questions... Morphology? Longevity? Incept dates? Cheers DD

    Read the article

  • How to Monitor Network in Medium-Sized Company?

    - by Kyle Lowry
    I work at a medium sized company (100+ employees). An issue that has been cropping up is network performance, internet access in particular. We have about 70 or more computers, a mix of Mac OS X and Windows XP & 7 machines. We have several servers (Exchange server, PC file servers, MS SQL, Blackberry, FTP, Mac server, etc). There are four main switches, a SonicWall firewall, and probably a couple routers in the server room with a dozen or so more scattered around the building. The network structure has grown organically over a number of years; and, as far as I know, there really isn't a monitoring solution in place. When we experience network issues (slow connections, dropped packets, and so on), our general solution is to power cycle some hardware or go around to each employee and ask them if they are uploading/downloading any large files. This is really inefficient and time consuming, and it does not allow us to monitor the network, tackling potential problems proactively. I would like to find a solution that would allow me to monitor network usage company-wide in real time, with detail going down to the individual computer, ideally. Given the hodgepodge of equipment and operating systems, what would be the best way to set up some kind of monitoring solution? Hardware, software, restructuring our network architecture?

    Read the article

  • Disable Windows 7 taskbar grouping. Not combining.

    - by Byran
    I've look near and far but I cannot find a way (setting or hack) to prevent Windows 7 from grouping taskbar buttons together that are "related". I'm not talking about the option to combine or collapse related buttons into one item. I can find that setting at: Taskbar and Start Menu Properties Taskbar Taskbar buttons: This is what I an not looking for: How to Enable or Disable Windows 7 Taskbar Button Grouping I'm talking about how Windows 7 seams to think that it's doing me a favor by grouping all my Google Chrome buttons together and grouping all my Explorer buttons together etc. My workflow in Windows XP was to use the program Taskbar Shuffle to allow me to reorganize my taskbar buttons into related task "groups" I was working on. For example: [Start Button] | [iTunes] [Outlook Express] [Chrome Gmail] [layered design folder] [Photoshop CS4] [exported images folder] [website root folder] [Dreamweaver CS4] [Chrome www.MyAwesomeWebsiteImBuilding.com] [Chrome Recent web search] [some unrelated folder] Windows 7 doesn't seem to let me do this. It wants to do: [Start Button] | [layered design folder][exported images folder][website root folder][some unrelated folder] | [Chrome www.MyAwesomeWebsiteImBuilding.com]Chrome [Gmail][Chrome Recent web search] | [iTunes] | [Outlook Express] | [Photoshop CS4] | [Dreamweaver CS4] Does anyone know of a tool or hack to prevent Windows 7 from grouping taskbar buttons?

    Read the article

  • Disable all the idiot-checking in Mac OS X

    - by Fake Name
    I am a Windows/Linux user, who is learning Mac OS X out of interest in doing dev-work for the iPad which I recently purchased. However, OS X is driving me nuts by trying to protect all it's system files, hiding all of the important OS components I want to tweak, and generally making it impossible to do any modification to the OS in general to make it more usable. Therefore, is there a way to turn off all the idiot-checking in Finder? On XP, I can disable "Hide Protected Operating system files" and set "Show Hidden Files". On linux, there really aren't many hidden files, and changing the configuration for .files is easy enough in Gnome and XFCE. How can I set up OS X in a similar way. I am not new to computers, and I am fully aware that deleting system files can damage or even irreparably disable a OS install. Therefore, If I intentionally try to delete a file, or move something, it's probably intentional, and I am willing to accept the consequences in any case. At this point, I have fallen back to doing everything through the command line (which takes forever), because Finder is practically unusable. (As for what I am attempting to do, I also asked about GUI changes here.)

    Read the article

  • Elevating UAC via .bat file?

    - by jslaker
    Pretty straightforward one that I'm having trouble finding an answer to. serverfault previously helped me with finding a way to automate Windows updates without using WSUS. It's working fantastically, but to run it over the network, you have to first mount a shared drive. That's pretty simple XP since you just mount the drive and run the updater. On Vista and W7, though, this all has to be done with elevated privileges to work correctly. The UAC account can't see network drives mounted by the regular user, so in order to get everything working, I have to mount the share via net use from an escalated shell. I'd like to automate mounting this share and launching the updater via a simple .bat file. I could probably just instruct everybody to right click "Run as Administrator" on the .bat file, but I'd like to keep things as simple as possible and have the .bat automatically prompt the user to escalate their privileges. Since these computers don't belong to us, I can't count on anything like Powershell being installed, so that rules any solution along those lines out and pretty much have to rely on things that would be included in an RTM Vista install. I'm hoping I'm mostly missing something obvious here. :)

    Read the article

  • How can I disable flashing icons on Windows 7 taskbar?

    - by Jebego
    I set my Windows 7 taskbar to auto-hide. However, sometimes when a program changes or something new happens in a program, the taskbar will show its self, and its respective taskbar icon will begin flashing orange. Here's what I'm talking about: To make the taskbar hide again, I have click on the program before I can go back to what I was doing. Anyways, I personally find this very annoying, and would love to find a way to either: Prevent the taskbar from having such alerts. Prevent the taskbar from showing its self when it has such alerts. I've searched around quite a bit, and really only found answers to this for XP. I've also found another Stack Exchange Question looking for the same thing for Windows 7. However, none of the answers to the question were really what I'm looking for. I'm not looking to hide the taskbar, or control the number of flashes. However, this answer seems to be what I'm looking for, so I downloaded and tried out the program. It works perfectly, other than the fact that the start menu icon is always shown, regardless of the taskbar being set to auto-hide. So, any ideas on how to fix this problem?

    Read the article

< Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >