Search Results

Search found 24965 results on 999 pages for 'linux kvm'.

Page 336/999 | < Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343  | Next Page >

• Redirecting program errors to both log and error file

  - by Gnanam

  I've a Java standalone program scheduled to run as cron at every 10 minutes I want to catch/write errors thrown by this Java program both in the log file and also as a separate error file (MyJavaStandalone.err). I know the following commands: Errors redirected to a separate file but not to log file /usr/java/jdk1.6.0/bin/java MyJavaStandalone >> MyJavaStandalone.log 2>> MyJavaStandalone.err & Both log and errors are redirected to the same log file, but errors alone are not written to a separate error file /usr/java/jdk1.6.0/bin/java MyJavaStandalone >> MyJavaStandalone.log 2>&1 &

  Read the article

• RTNETLINK answers: Invalid argument

  - by LinuxPenseur

  When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

  Read the article

• How to recover the ubuntu system?

  - by Hoang

  I istalled the ubuntu virtual machine on vmware. However, one time the disk was full, the system was installing some updates, it quit without giving any message. Now the system is crashed, I can not even launch firefox to download data. How can I recover this virtual machine to a previous state?

  Read the article

• Grant a user access to directories shared by root (mod: 770)

  - by Paul Dinham

  I want to grant a user (username: paul) access to all directories shared by root with mod 770. I do it this way: groups root (here comes a list of groups in which root user is) usermod -a -G group1 paul usermod -a -G group2 paul usermod -a -G group3 paul ... All the 'group1', 'group2', 'group3' are seen in the group list of root user. However, after adding 'paul' to all groups above, he still can not write to directories shared by root user with mod 770. Did I do it wrongly?

  Read the article

• Connect two subnets without router

  - by Shcheklein

  I got two Comcast routers with two different subnets on each. Every subnet contains 5 static IPs. Two questions: Are there any problems if both routers and machines from both subnets are connected into one switch? Security issues doesn't matter there. I need to know if there are some performance or other problems. Is it possible to make machines from different subnets to see each other if they all are connected into one switch? Some static routing, add ARP records or somethig else ... I just want to avoid configuring second ethernet adaptors, third router or something. And I need to connect these subnets vai high-speed local network.

  Read the article

• script calling script as other user

  - by viktor tron

  Using CentOs, I want to run a script as user 'training' as a system service. I use daemontools to monitor the process, which needs a launcher script that is run as root: : #!/bin/bash exec >> /var/log/training_service.log 2>&1 setuidgid training training_command This last line is not good enough since for training_command, we need environment for training user to be set. : su - training -c 'training_command' gives 'standard in must be tty' as su making sure tty is present to potentially accept password. I know I could make this disappear by modifying /etc/sudoers a la Bash & 'su' script giving an error "standard in must be a tty" but i am reluctant and unsure of consequences. : runuser - training -c 'training_command' gives runuser: cannot set groups: Connection refused. I found no sense or resolution to this message. I am stuck. Is this something so hard to achieve? I appreciate all insight and guidance to best practice.

  Read the article

• Find out which task is generating a lot of context switches on linux

  - by Gaks

  According to vmstat, my Linux server (2xCore2 Duo 2.5 GHz) is constantly doing around 20k context switches per second. # vmstat 3 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 2 0 7292 249472 82340 2291972 0 0 0 0 0 0 7 13 79 0 0 0 7292 251808 82344 2291968 0 0 0 184 24 20090 1 1 99 0 0 0 7292 251876 82344 2291968 0 0 0 83 17 20157 1 0 99 0 0 0 7292 251876 82344 2291968 0 0 0 73 12 20116 1 0 99 0 ... but uptime shows small load: load average: 0.01, 0.02, 0.01 and top doesn't show any process with high %CPU usage. How do I find out what exactly is generating those context switches? Which process/thread? I tried to analyze pidstat output: # pidstat -w 10 1 12:39:13 PID cswch/s nvcswch/s Command 12:39:23 1 0.20 0.00 init 12:39:23 4 0.20 0.00 ksoftirqd/0 12:39:23 7 1.60 0.00 events/0 12:39:23 8 1.50 0.00 events/1 12:39:23 89 0.50 0.00 kblockd/0 12:39:23 90 0.30 0.00 kblockd/1 12:39:23 995 0.40 0.00 kirqd 12:39:23 997 0.60 0.00 kjournald 12:39:23 1146 0.20 0.00 svscan 12:39:23 2162 5.00 0.00 kjournald 12:39:23 2526 0.20 2.00 postgres 12:39:23 2530 1.00 0.30 postgres 12:39:23 2534 5.00 3.20 postgres 12:39:23 2536 1.40 1.70 postgres 12:39:23 12061 10.59 0.90 postgres 12:39:23 14442 1.50 2.20 postgres 12:39:23 15416 0.20 0.00 monitor 12:39:23 17289 0.10 0.00 syslogd 12:39:23 21776 0.40 0.30 postgres 12:39:23 23638 0.10 0.00 screen 12:39:23 25153 1.00 0.00 sshd 12:39:23 25185 86.61 0.00 daemon1 12:39:23 25190 12.19 35.86 postgres 12:39:23 25295 2.00 0.00 screen 12:39:23 25743 9.99 0.00 daemon2 12:39:23 25747 1.10 3.00 postgres 12:39:23 26968 5.09 0.80 postgres 12:39:23 26969 5.00 0.00 postgres 12:39:23 26970 1.10 0.20 postgres 12:39:23 26971 17.98 1.80 postgres 12:39:23 27607 0.90 0.40 postgres 12:39:23 29338 4.30 0.00 screen 12:39:23 31247 4.10 23.58 postgres 12:39:23 31249 82.92 34.77 postgres 12:39:23 31484 0.20 0.00 pdflush 12:39:23 32097 0.10 0.00 pidstat Looks like some postgresql tasks are doing 10 context swiches per second, but it doesn't all sum up to 20k anyway. Any idea how to dig a little deeper for an answer?

  Read the article

• How to tell if PAE is hurting me?

  - by James

  I have a couple of servers with 20-30 GB RAM that are running (a variant of) RHEL4. They are currently running the SMP i386 kernel, not x64, not even the hugemem kernel. This means LowMem is confined to < 1G, and thus dentry_cache and ext3_inode_cache to 100M or so each. How can I tell if this is a problem? Here's a typical vmstat report while it's compiling some Java: $ vmstat 10 procs -----------memory---------- ---swap-- -----io---- --system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 1 1 0 19493816 394740 922420 0 0 1058 2292 1491 1020 6 3 80 12 2 1 0 19519480 395244 850156 0 0 1179 1412 1329 1195 9 4 75 12 1 1 0 19557368 392616 828344 0 0 1783 1680 1498 1756 14 5 72 9 I don't like the way bi is nonzero when there is so much memory free. I imagine slabtop could point more directly to the problem but I don't really understand how to interpret its output.

  Read the article

• samba4 not building in archlinux.

  - by kmplsv

  cp bin/tdbtool bin/tdbdump bin/tdbbackup /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/bin cp ./include/tdb.h /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/include cp tdb.pc /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/pkgconfig cp libtdb.a libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib rm -f /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so ln -s libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so rm -f /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so.1 ln -s libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so.1 mkdir -p /tmp/yaourt-tmp-root/aur-samba4/pkg/`/tmp/yaourt-tmp-root/aur-samba4/src/bin/python -c "import distutils.sysconfig; print distutils.sysconfig.get_python_lib(1, prefix='/opt/samba4/samba')"` cp tdb.so /tmp/yaourt-tmp-root/aur-samba4/pkg/`/tmp/yaourt-tmp-root/aur-samba4/src/bin/python -c "import distutils.sysconfig; print distutils.sysconfig.get_python_lib(1, prefix='/opt/samba4/samba')"` /bin/install -c -d /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/share/man/man8 for I in manpages/*.8; do \ /bin/install -c -m 644 $I /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/share/man/man8; \ done /bin/install: cannot stat `manpages/*.8': No such file or directory make: *** [installdocs] Error 1 Aborting... ==> ERROR: Makepkg was unable to build samba4. ==> Restart building samba4 ? [y/N] ==> ------------------------------- ==>c any ideas as what is causing my build to fail? i'm assuming it's an issue with manpages but i can't figure out exactly what package it is looking for that i don't have.

  Read the article

• sendmail Name server timeout

  - by broody

  Complete sendmail newbie here... I've been trying to get mailing to work in PHP and I've root caused it down to sendmail's complaint about "Name server timeout": >sendmail -t -v >From: [email protected] >To: [email protected] >. gmail.com: Name server timeout [email protected]... Transient parse error -- message queued for future delivery [email protected]... queued So it sounds like a DNS issue? But I can do a "dig mx gmail.com" and it will query successfully. Here's what confuses me... I can get sendmail to work two other ways. The first way is through telnet: >telnet 127.0.0.1 25 >Helo me >Mail from: [email protected] >Rcpt to: [email protected] >. message sent And the second way is by explicitly appending the sendmail.cf, but this is strange because it's the exact same file I use to configure sendmail to begin with: >sendmail -t -v -C/etc/mail/sendmail.cf But none of these solutions will resolve my PHP mailing... I am clueless as to what is going on... appreciate any help.

  Read the article

• How do I install a newer version of GTK in Ubuntu without replacing the current one?

  - by William Friesen

  I am trying to compile file-roller from git, but running autogen.sh gives me this error configure: error: Package requirements (gtk+-3.0 >= 2.91.1) were not met: No package 'gtk+-3.0' found Consider adjusting the PKG_CONFIG_PATH environment variable if you installed software in a non-standard prefix. Alternatively, you may set the environment variables GTK_CFLAGS and GTK_LIBS to avoid the need to call pkg-config. See the pkg-config man page for more details. I am running Ubuntu Maverick and don't wish to completely replace my current version of gtk, glib, etc. I have tried to compile GTK using the --prefix argument of autogen.sh, but this gives me a similar error about my version of glib. How can I successfully compile file-roller using these new libraries without borking my install?

  Read the article

• Program complains not enough disk space even if the disk space exists

  - by user1189899

  I have an EXT3 partition mounted in ordered data mode. If a power failure occurs when a program is creating files on that partition, I see that space usage reported is normal and I don't see any partial written files. But when I try to run the same program again after the system comes back up it complains that there is not enough disk space. Even though the free space reported is far more than required. The program always succeeds in normal conditions. Also the problem seems to disappear when the partition is remounted. I was wondering what could be the right way to handle the situation other than unmounting and remounting.

  Read the article

• Windows 7 doesn't boot when second hard disk is connected

  - by kenshin9786

  I'm sorry for my bad english on beforehand. I have two hard disks, one SATA and another IDE. I have windows XP and 7 on the SATA one, and Ubuntu on the IDE. Both of them boots and works, bios recognizes them, just works. After I installed Windows 7, and connected the IDE drive, it freezes on "Starting Windows" (the black screen with the Windows logo). I unplug the IDE drive, and it starts normally. Windows XP starts normally on both situations (with or without the IDE one connected), same for Ubuntu (it works with both disks connected or just the IDE where it is). The IDE drive is on good status according to SMART. The IDE is first on boot order. It goes to the Ubuntu's grub first, then by default it goes to the Windows 7 bootloader, and then to XP. I think the problem is not about the bootloader or grub. I just read that it can be solved formatting the "problematic" hard disk because Windows 7 cannot handle so many active partitions or something like that. But that's not an option for me, I don't want to lose my Ubuntu nor have it unbootable. How can I solve this without this consecuences I mentioned? Any help would be appreciated.

  Read the article

• Recompiling yum installation

  - by Saif Bechan

  I have installed Nginx using yum. Now to add modules to the existing installation i have to recompile Nginx from source. How can i recompile a yum installation. There is no source. Should I uninstall the yum package, and then download the source package and recompile it with the module and then install everything and reconfigure it again???

  Read the article

• monit syntax error : "if 5 restarts within 5 cycles then alert"

  - by omry

  I am trying to get an alert from monit if it fails to restart a service 5 times, but I get a syntax error /etc/monit/monit.d/engine.conf:5: Error: syntax error 'alert' this is the engine.conf file: check process engine with pidfile /var/run/engine.pid group engine start program = "/etc/init.d/engine start" stop program = "/etc/init.d/engine stop" if 5 restarts within 5 cycles then alert any idea what's wrong with it?

  Read the article

• Nexus functionality is limited after installation

  - by Dmitriy Sukharev

  I have a CentOS based server with Sonatype Nexus 2.0.4-1 installed. The issue is that there are no standard "Artifact Search", "Advanced Search", "Browse Index", "Refresh Index" Nexus features, as well as Artifact Information tab after selection of any artifact (only Maven Information tab). I tried to Google, but was amazed that there're no information about this issue. Actually it looks like all actions I've done are: wget http://www.sonatype.org/downloads/nexus-2.0.4-1-bundle.tar.gz tar -xvf nexus-2.0.4-1-bundle.tar.gz cp -r nexus-2.0.4-1 sonatype-work /opt/ ln -s /opt/nexus-2.0.4-1/* /opt/nexus ln /opt/nexus/bin/nexus /etc/init.d/ chmod 755 /etc/init.d/nexus vim /etc/init.d/nexus NEXUS_HOME=“/opt/nexus” RUN_AS_USER=“nexus” useradd -s /sbin/nologin -d /var/lib/nexus nexus chown -R nexus /opt/nexus/ chown -R nexus /opt/nexus-2.0.4-1/ sudo -u nexus cp /opt/nexus/conf/examples/proxy-https/jetty.xml /opt/nexus/conf/ To force Nexus be available through HTTPS I went to Administration - Server - Application Server Settings as admin and changed Base URL to https:// external IP/nexus and set Force Base URL to true. Any ideas how to get missed Nexus features?

  Read the article

• Out of disk space on 4GB partiton yet it's only using 2GB

  - by Camsoft

  I'm running Ubuntu and have had a problem where the root partition has run out of disk space. When I perform df -h I get the following: Filesystem Size Used Avail Use% Mounted on /dev/sda6 4.6G 4.5G 0 100% / Yet there are only 2GB of files actually using up this partition. I then ran the following df -i and I get the following: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda6 305824 118885 186939 39% / I have no idea what the -i flag does but it clearly shows that only 39% is used. Can anyone explain where my disk space has gone?

  Read the article

• Unable to build Python modules in Mandriva 2010

  - by SteveJ

  I am trying to build a Python module (pyfits) but I get the following error: # python setup.py install /home/steve/src/pyfits-2.2.2/stsci_distutils_hack.py:239: DeprecationWarning: os.popen3 is deprecated. Use the subprocess module. (sin, sout, serr) = os.popen3(cmd) running install error: invalid Python installation: unable to open /usr/lib64/python2.6/config/Makefile (No such file or directory) I get the same error when I try and build other modules so my guess is I am missing a Python development library. I am running Mandriva 2010.0, any suggestions?

  Read the article

• rsyslog - regex trouble

  - by benmccann

  I'm trying to setup the logentries service. If a log entry has a token in it then I would like to send it to api.logentries.com:10000. The token is a guid in the format aaaaaaaa-bbbb-cccc-dddd-eeeeeeeeeeee. Right now I'm doing: # If there's a logentries token then send it directly to logentries :msg, regex, ".*[a-z0-9]{8}-[a-z0-9]{4}-[a-z0-9]{4}-[a-z0-9]{4}-[a-z0-9]{12}.*" & @@api.logentries.com:10000 I checked the rsyslog debug logs and my regex is not matching, but I can't figure out why or how to fix it: 5245.961161378:7fb79b514700: Filter: check for property 'msg' (value ' fb1c507f-2ede-4d7f-a140-2bd8d56e133 - application - [play-akka.actor.default-dispatcher-1] - Found user: 4fb11ea5e4b00a1aeebe2800') regex '.*[a-z0-9]{8}-[a-z0-9]{4}-[a-z0-9]{4}-[a-z0-9]{4}-[a-z0-9]{12}.*': FALSE

  Read the article

• Error removing packages in Ubuntu using Synaptic

  - by ronakin

  I'm using Ubuntu 10.04 and during my tries to free space I've removed several packages such as: openoffice, all editors, and some more packages such as players and printers drivers that I don't need and seem o.k to remove. However, after restart, the graphical interface doesn't load, I'm in the xserver, I have console but not gui. I was wondering if anyone can tell me which packages I should not remove or let me know of dependencies I need to consider when messing with packages? Thanks!

  Read the article

• Server configurations for hosting MySQL database

  - by shyam

  I have a web application which uses a MySQL database hosted on a virtual server. I've been using this server when I started the application and when the database was really small. Now it has grown and the server is not able to handle the db, causing frequent db errors. I'm planning to get a server and I need suggestions for that. Like I said, the db is now 9 GB, and is growing considerably fast. There are a number of tables with millions of rows, which are frequently updated and queried. The most frequent error the db shows is Lock wait timeout exceeded. Previously there used to be "The total number of locks exceeds the lock table size" errors too, but I could avoid it by increasing Innodb buffer pool size. Please suggest what configurations should I look for in the server I should buy. I read somewhere that the db should ideally have a buffer pool size greater than the size of its data, so in my case I guess I'd need memory gt 9 GB. What other things should I look for in the server? Just tell me if I should give you more info about the

  Read the article

• Is it possible to mount a disk image, created with dd, to a directory on a mounted external usb hdd?

  - by Keeper Hood

  I have an image of my home (/dev/sda3) partition, which I've created using the "dd" command. dd if=/dev/sda3 of=/path/to/disk.img I've deleted the home partition via gparted in order to enlarge my /dev/root partition. Then I've recreated the /dev/sda3 partition which is smaller in size then the one I've backed up to the image. I was wondering since I have a 2TB external HDD, could it be possible to mount my backed up image on the external HDD and then copy the files into the /home directory. Since the external HDD would be already in a "mounted state", I'm unsure whether this is a good idea, mounting on a mounted device. I'm running Slackware 13.37 (64bit). used ext4 on all the partitions. resized the root partition with gparted live cd. I've tried mount -t ext4 /path/to/disk.img /mng/image -o loop It gave me an fs error (wrong fs type, bad option, bad superblock on dev/loop/0) Then i did dmesg | tail which outputs: EXT4-fs (loop0) : bad geometry: block count 29009610 exceeds size of defice (1679229 blocks) I have no idea what to do, I want to restore my /home data from the image I've backed up.

  Read the article

• SLES AutoYaST Script Validity Verification

  - by Xerxes

  Does anyone here write their own customized AutoYaST scripts for building SLES servers? I'm not talking about generating them with yast2 autoyast. If so, have you found a way to verify the syntax? xmllint is good as far as telling you that the XML syntax is valid, but with an upto date DTD, it can't tell you anything more, and the shipped DTDs are out-of-date. I've opened a ticket with Novell on this, but who knows when and what I'll hear back.

  Read the article

• What are the pros and cons of OCFS2 and GFS2 filesystems versus NFS ?

  - by edomaur

  We need to set up a SAN accessible from a bunch of computers, both virtualized and real. We have an iSCSI SAN and I need to ponder some of the options. What are the differences between GFS2 and OCFS2 ? Are they production-ready ? And how they compare to NFS ? (I can use it with that SAN)

  Read the article

• qpid-cpp-client won't update through yum

  - by alexus

  somewhere around last week I received a notification for update, so I've tried "yum update" and that's what I'm getting... [alexus@wcmisdlin02 ~]$ sudo yum update Loaded plugins: refresh-packagekit Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package qpid-cpp-client.x86_64 0:0.10-3.el6 will be updated --> Processing Dependency: libqpidclient.so.5()(64bit) for package: matahari-service-0.4.0-5.el6.x86_64 --> Processing Dependency: libqpidclient.so.5()(64bit) for package: matahari-host-0.4.0-5.el6.x86_64 --> Processing Dependency: libqpidclient.so.5()(64bit) for package: matahari-net-0.4.0-5.el6.x86_64 --> Processing Dependency: libqpidcommon.so.5()(64bit) for package: matahari-service-0.4.0-5.el6.x86_64 --> Processing Dependency: libqpidcommon.so.5()(64bit) for package: matahari-host-0.4.0-5.el6.x86_64 --> Processing Dependency: libqpidcommon.so.5()(64bit) for package: matahari-net-0.4.0-5.el6.x86_64 ---> Package qpid-cpp-client.x86_64 0:0.14-22.el6_3 will be an update ---> Package qpid-cpp-client-ssl.x86_64 0:0.10-3.el6 will be updated ---> Package qpid-cpp-client-ssl.x86_64 0:0.14-22.el6_3 will be an update ---> Package qpid-qmf.x86_64 0:0.10-6.el6 will be updated ---> Package qpid-qmf.x86_64 0:0.14-14.el6_3 will be an update --> Finished Dependency Resolution Error: Package: matahari-net-0.4.0-5.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) Requires: libqpidcommon.so.5()(64bit) Removing: qpid-cpp-client-0.10-3.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) libqpidcommon.so.5()(64bit) Updated By: qpid-cpp-client-0.14-22.el6_3.x86_64 (sl-security) Not found Error: Package: matahari-net-0.4.0-5.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) Requires: libqpidclient.so.5()(64bit) Removing: qpid-cpp-client-0.10-3.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) libqpidclient.so.5()(64bit) Updated By: qpid-cpp-client-0.14-22.el6_3.x86_64 (sl-security) Not found Error: Package: matahari-service-0.4.0-5.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) Requires: libqpidclient.so.5()(64bit) Removing: qpid-cpp-client-0.10-3.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) libqpidclient.so.5()(64bit) Updated By: qpid-cpp-client-0.14-22.el6_3.x86_64 (sl-security) Not found Error: Package: matahari-service-0.4.0-5.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) Requires: libqpidcommon.so.5()(64bit) Removing: qpid-cpp-client-0.10-3.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) libqpidcommon.so.5()(64bit) Updated By: qpid-cpp-client-0.14-22.el6_3.x86_64 (sl-security) Not found Error: Package: matahari-host-0.4.0-5.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) Requires: libqpidcommon.so.5()(64bit) Removing: qpid-cpp-client-0.10-3.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) libqpidcommon.so.5()(64bit) Updated By: qpid-cpp-client-0.14-22.el6_3.x86_64 (sl-security) Not found Error: Package: matahari-host-0.4.0-5.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) Requires: libqpidclient.so.5()(64bit) Removing: qpid-cpp-client-0.10-3.el6.x86_64 (@anaconda-ScientificLinux-201107271550.x86_64) libqpidclient.so.5()(64bit) Updated By: qpid-cpp-client-0.14-22.el6_3.x86_64 (sl-security) Not found You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest [alexus@wcmisdlin02 ~]$ any ideas?

  Read the article

< Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343  | Next Page >