Search Results

Search found 11608 results on 465 pages for 'usb extension'.

Page 350/465 | < Previous Page | 346 347 348 349 350 351 352 353 354 355 356 357  | Next Page >

  • GRUB2 stuck at rescue console, showing "unknown filesystem" for all partitions

    - by AndiDog
    I installed Ubuntu 12.04 on my external USB drive, where I have a 700GB NTFS partition followed by the new 6GB ext4 partition and a swap partition (all primary). The GRUB MBR is also installed to the external hard disk. Since my BIOS puts the external drive as first disk when booting, I removed my internal hard disk before installation in order to avoid ordering problems. Now when I boot from the external drive, GRUB is stuck at the rescue console with the error "unknown filesystem". grub rescue> ls (hd0) (hd0,msdos3) (hd0,msdos2) (hd0,msdos1) ls (hd0,<any of them>)/ gives me "unknown filesystem", thus also "insmod normal" GRUB doesn't seem to be able to read my Linux partition as you can see above?! How can I solve this? Additional info: bootinfoscript says (this is with the internal drive in again, but that does not make a difference): Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos2)/boot/grub on this drive. sdb1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sdb2: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.04 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb3: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info:

    Read the article

  • menu not showing in apps when maximized 12.10

    - by chazdg
    I have removed the Global App Menu as I prefer to have the minimize, maximize, close buttons on the right side of each app. I did this with no problem in 12.04. I did an upgrade to 12.10 and noticed that Chrome, Chromium and Firefox all use the Global Menu. I have done the following: sudo apt-get autoremove appmenu-gtk appmenu-gtk3 appmenu-qt I have disabled the Firefox extension. I removed the corresponding Firefox package but still only have a global menu. I tried Gconf but apparently that does not work in 12.10. I then tried Dconf and found this fix on Google: org gnome desktop wm preferences, look for "button_layout" on the right panel. Here is the problem, after desktop, I do not have wm. I reset Unity and got a message saying something about wm is missing. I rebooted and opened Chrome and still no fix. I then clicked maximize and once Chrome was not maximized anymore, the minimize, maximize, close buttons show up in Chrome. Same with Firefox! Any ideas? I am truly stumped. Firefox and Chrome work fine in KDE Plasma and Gnome when maximized.

    Read the article

  • 25 years old and considering a career change...possible? practical?

    - by mq330
    Hi all, I'm new to this site and new to programming as well. I've spent some time going through an intro cs book that uses python as the language of choice. I find the exercises interesting and engaging and I generally have had a favorable experience programming so far. I've gone through some of the basics with python like writing simple programs, basics of GUIs, manipulating strings, lists, defining functions, etc. And I've always loved technology. Although I've never done any real hardcore programming yet, I was inclined to building websites from a very young age but I never really developed my skills. Now, the thing is I'm 25, I have my bacholors in environmental studies and two masters degrees in urban planning and landscape architecture respectively. I know, it would be quite a departure to pursue a career in programming at this point. Currently, I'm working as a geographic information systems intern. I've taken some GIS classes and have a lot of experience with making maps, doing spatial analysis etc. So what I'm thinking is maybe I can learn some solid programming skills and apply these skills in the field of GIS. From what I've seen, .net languages are the norm in this arena. Could you perhaps provide some guidance to me in terms of what languages I should focus on or courses I should take at this point? What about for building web mapping applications? Also, I was thinking about getting a certificate in programming from a university extension program. Do you think it would be worth it? And furthermore, do you think potential employers would be interested in hiring someone like me (once I get a couple of languages down pretty well) as an intern or in an entry level position? I'll be living in the bay area so I feel that there should be decent opportunities even though I don't have a b.s. in cs.

    Read the article

  • How to connect MTS MBlaze

    - by murali_ma
    i have installed ubuntu 11.04 inside the windows xp. i have MTS Mblaze USB Modem. (my service provider is MTS MBlaze,india) i want to use Mblaze into ubuntu so that i did the following steps for make connecting the device. from the task bar->edit connections->mobile broadband->choose country->mts mblaze and ok i give username and password ([email protected] and password MTS. ok now i enable mobile broadband , MTS MBlaze connection1(connection name) from task bar. steps followed from "http://randomshandom.wordpress.com/2010/12/20/how-to-connect-mts-mblaze-device-in-ubuntu-10-10-11-04/#more-3" for the first time it successfully connected and browse the internet. after i restart the system i connect it. it does not connected. it shows Modem network disconnected. i accessed many times and delete the connection and recreated but i does not help me. if i try to connect device i think it the search the network, i saw the wave signal. img Image for showing problem:

    Read the article

  • Dual boot UEFI Windows 7 and Ubuntu 12.04 (both 64 bits). W7 entry doesn't appear in GRUB

    - by Joe
    After trying to install both OS during 2 days, I'm confused and getting mad... I have SSD 128 GB and HDD 500 GB both empty. My laptop is Asus K55VM. BIOS support UEFI. What I have done: Install new SSD (Samsung 830 128GB) Use GParted on liveCD to create new table of partitions (GPT) and create 3 partitions (in the SSD) for different purposes: Partition 1: 80 GB (w7); Partition 2: 30 GB (Ubuntu 12.04 -Just / -); Partition 3: 10 GB unused (for future extesion of the other partitions) Install Windows 7 (with UEFI) in Partition 1. This create: /dev/sda1 - 100 MB for System (UEFI boot I guess) - FAT32 /dev/sda2 - 100 MB aprox. for MSR /dev/sda3 - 79.800 MB aprox. for Windows7 data In this point everything works fine. I have W7. Now I install Ubuntu 12.04 amd64 (with UEFI) as follows: Install / in Partition 2 - /dev/sda4 30 GB ext4, and in the hdd I install /home and swap. I select bootloader in /dev/sda1 (where it's supposed to be the UEFI boot). I install updates and reboot. Problem: Now just appears grub menu with Ubuntu entries and not Windows 7. Alternative solution found: When I turn on laptop, before loading GRUB I press ESC key and appear BIOS boot, so I can select to boot the Windows partition, Ubuntu partition, DVD, USB, etc... but I think is not the best way to boot different OS. I've tried: sudo update-grub2 with no success. What can I do??

    Read the article

  • Create Your Own Quick Calculator Function for the Terminal

    - by The Geek
    If you’re anything like me, you’ve always got a Terminal window open, and you probably have even assigned a hotkey to bring it up anytime. So why open up the boring calculator when you can solve equations right there on the command line? This is a simple method for creating a calculator using the built-in function support in the Bash shell. Essentially all we’re doing is assigning the question mark to run the bc command with whatever arguments you type after it. Latest Features How-To Geek ETC RGB? CMYK? Alpha? What Are Image Channels and What Do They Mean? How to Recover that Photo, Picture or File You Deleted Accidentally How To Colorize Black and White Vintage Photographs in Photoshop How To Get SSH Command-Line Access to Windows 7 Using Cygwin The How-To Geek Video Guide to Using Windows 7 Speech Recognition How To Create Your Own Custom ASCII Art from Any Image Vintage Posters Showcase the History of Tech Advertising Google Cloud Print Extension Lets You Print Doc/PDF/Txt Files from Web Sites Hack a $10 Flashlight into an Ultra-bright Premium One Firefox Personas Arrive on Firefox Mobile Focus Booster Is a Sleek and Free Productivity Timer What is the Internet? From the Today Show January 1994 [Historical Video]

    Read the article

  • No operating system found even when grub2 was reinstalled

    - by Cruzer
    I know there have been many variations on this question and have certainly tried to do my research. I don't really know what I'm doing so I would rather not take risks. I am trying to dual boot xubuntu and windows 7. I started out with xubuntu and just installed windows. Of course, the mbr got overwritten and windows didn't seem to recognize linux. So I booted to the live cd and rewrote the mbr. And of course, now I get the error "No Operating System Found" on startup. I have been following these tutorials to help me out. community.linuxmint.com/tutorial/view/245 unix.stackexchange.com/questions/96977/grub-wont-install ubuntuforums.org/showthread.php?t=2036730 Specifically, I ran these commands: # sdb2 is the partition with xubuntu sudo mount /dev/sdb2 /mnt # sdb1 is my boot partition sudo mount /dev/sdb1 /mnt/boot # not sure what this does, but ran it anyway... for i in /dev /dev/pts /proc /sys /run; do sudo mount -B $i /mnt$i; done sudo chroot /mnt #once chrooted grub-install /dev/sdb update-grub here's a link to my gparted https://www.dropbox.com/s/zpbbzh9z7k1l3pj/gparted.png EDIT--- didn't realize that the drive letters are different in the picture than in my code (its sda in the pic instead of sdb). I have been restarting a lot and sometimes the drive letters change and make my usb into sda.

    Read the article

  • Recursive function with for loop python

    - by user134743
    I have a question that should not be too hard but it has been bugging me for a long time. I am trying to write a function that searches in a directory that has different folders for all files that have the extension jpg and which size is bigger than 0. It then should print the sum of the size of the files that are in these categories. What I am doing right now is def myFuntion(myPath, fileSize): for myfile in glob.glob(myPath): if os.path.isdir(myFile): myFunction(myFile, fileSize) if (fnmatch.fnmatch(myFile, '*.jpg')): if (os.path.getsize(myFile) > 1): fileSize = fileSize + os.path.getsize(myFile) print "totalSize: " + str(fileSize) THis is not giving me the right result. It sums the sizes of the files of one directory but it does not keep suming the rest. For example if I have these paths C:/trial/trial1/trial11/pic.jpg C:/trial/trial1/trial11/pic1.jpg C:/trial/trial1/trial11/pic2.jpg and C:/trial/trial2/trial11/pic.jpg C:/trial/trial2/trial11/pic1.jpg C:/trial/trial2/trial11/pic2.jpg I will get the sum of the first three and the the size of the last 3 but I won´t get the size of the 6 together, if that makes sense. Thank you so much for your help!

    Read the article

  • Updated Virtual Machine for VS/TFS 2010

    - by Enrique Lima
    If you had downloaded the previous version of the virtual machines, then you are likely aware they are set to expire soon (12/15/2010). Brian Keller announced yesterday (blog post here) the availability of a vm refresh (new expiration set for 6/1/2011). What is part of the refresh? Here is the excerpt from Brian’s post: “ The version of this virtual machine which was refreshed on December 9, 2010, includes the following additions: · Visual Studio 2010 Feature Pack 2 · Team Foundation Server 2010 Power Tools (September 2010 Release) · Visual Studio 2010 Productivity Power Tools (these are disabled in VS so that the screenshots of the hands-on-labs still match; you can quickly enable the Productivity Power Tools via Tools -> Extension Manager from within Visual Studio) · Test Scribe for Microsoft Test Manager · Visual Studio Scrum 1.0 Process Template · All Windows Updates through December 8, 2010 · Lab Management GDR (KB983578) · Visual Studio 2010 Feature Pack 2 pre-requisite hotfix (KB2403277) · Microsoft Test Manager hotfix (KB2387011) · Minor fit-and-finish fixes based on customer feedback · A new expiration date of June 1, 2011” The links to download the Virtual Machines are: Hyper-V: http://www.microsoft.com/downloads/en/details.aspx?FamilyID=e0198b64-4acb-4709-b07f-359fb4d523bc&displaylang=en Windows Virtual PC (Win 7): http://www.microsoft.com/downloads/en/details.aspx?FamilyID=509c3ba1-4efc-42b5-b6d8-0232b2cbb26e&displaylang=en

    Read the article

  • Ubuntu 12.04 LTX Install Problems (See post for system build details.)

    - by Lokitez
    This is my first ever attempt at working with Ubuntu. I have only ever installed Windows in the past and that may be the problem. I purchased all new hardware this week and I would really like to give Ubuntu a chance (especially since I don't want to buy another Windows license). First, the hardware: AMD FX-8150 Zambezi 3.6GHz Socket AM3+ 125W Eight-Core Desktop Processor ASUS Crosshair V Formula AM3+ AMD 990FX SATA 6Gb/s USB 3.0 ATX AMD Gaming Motherboard SAMSUNG 830 Series MZ-7PC128D/AM 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) - This is my intended boot drive. Western Digital VelociRaptor WD5000HHTZ 500GB 10000 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive - This is a backup drive that I have installed Windows Vista on until I can get Ubuntu to work. G.SKILL Ripjaws X Series 16GB (2 x 8GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 I have downloaded and tried to install both Ubuntu 64 bit and Kubuntu 64 bit (both 12.04). Both will always fail to copy a file during install or otherwise lockup during install to the SSD. I have burned two copies of the Ubuntu 12.04 and had the install fail with both. I have installed Vista onto the HDD. Is it possible to mount the Ubuntu file into

    Read the article

  • OpenXML error “file is corrupt and cannot be opened.”

    - by nmgomes
    From time to time I ear some people saying their new web application supports data export to Excel format. So far so good … but they don’t tell the all story … in fact almost all the times what is happening is they are exporting data to a Comma-Separated file or simply exporting GridView rendered HTML to an xls file. Ok … it works but it’s not something I would be proud of. So … yesterday I decided to take a look at the Office Open XML File Formats Specification (Microsoft Office 2007+ format) based on well-known technologies: ZIP and XML. I start by installing Open XML SDK 2.0 for Microsoft Office and playing with some samples. Then I decided to try it on a more complex web application and the “file is corrupt and cannot be opened.” message start happening. Google show us that many people suffer from the same and it seems there are many reasons that can trigger this message. Some are related to the process itself, others with encodings or even styling. Well, none solved my problem and I had to dig … well not that much, I simply change the output file extension to zip and extract the zip content. Then I did the same to the output file from my first sample, compare both zip contents with SourceGear DiffMerge and found that my problem was Culture related. Yes, my complex application sets the Thread.CurrentThread.CurrentCulture  to a non-English culture. For sample purposes I was simply using the ToString method to convert numbers and dates to a string representation but forgot that XML is culture invariant and thus using a decimal separator other than “.” will result in a deserialization problem. I solve the “file is corrupt and cannot be opened.” by using Convert.ToString(object, CultureInfo.InvariantCulture) method instead of the ToString method. Hope this can help someone.

    Read the article

  • Acer aspire v3 771G ubuntu 13.04

    - by Jos
    Gooday, i have this acer and i have alot of boot problems (i suspect windows 8) and now i want to try ubuntu but when i use an usb to "try" ubuntu after the boot i get a black screen. now ive read some of the forums and i found something about NOMODESET i have not tried this as i dont know what this does exactly. now i have found this wiki entry https://wiki.ubuntu.com/Bumblebee , i am by far no programmer and always reading all those commands have always kept me of linux because im scared i will !@#$ things up. is there anyway i can go to NOMODESET in the ubuntu "trial" and can i also include the bumblebee futures (coding?) and in how many ways wil this affect my laptops perfomance? reading the bumblebee entry its seems to be something about nvidia optimus and i dont reallt care much for the power saving, but will it affect any performance? im not a heavy pc gamer but i like tho do some gaming and streaming and such also on a rather big TV in wich this laptop already has it flaws in some games not running properly on 65" if this doesn't work or u advise me not to do this what else can i do to fix windows 8 or either some other linux version? i thankyou in advance

    Read the article

  • Convert collections of enums to collection of strings and vice versa

    - by Michael Freidgeim
    Recently I needed to convert collections of  strings, that represent enum names, to collection of enums, and opposite,  to convert collections of   enums  to collection of  strings. I didn’t find standard LINQ extensions.However, in our big collection of helper extensions I found what I needed - just with different names: /// <summary> /// Safe conversion, ignore any unexpected strings/// Consider to name as Convert extension /// </summary> /// <typeparam name="EnumType"></typeparam> /// <param name="stringsList"></param> /// <returns></returns> public static List<EnumType> StringsListAsEnumList<EnumType>(this List<string> stringsList) where EnumType : struct, IComparable, IConvertible, IFormattable     { List<EnumType> enumsList = new List<EnumType>(); foreach (string sProvider in stringsList)     {     EnumType provider;     if (EnumHelper.TryParse<EnumType>(sProvider, out provider))     {     enumsList.Add(provider);     }     }     return enumsList;     }/// <summary> /// Convert each element of collection to string /// </summary> /// <typeparam name="T"></typeparam> /// <param name="objects"></param> /// <returns></returns> public static IEnumerable<string> ToStrings<T>(this IEnumerable<T> objects) {//from http://www.c-sharpcorner.com/Blogs/997/using-linq-to-convert-an-array-from-one-type-to-another.aspx return objects.Select(en => en.ToString()); }

    Read the article

  • Can't install Ubuntu 12.04 64-bit on a dual-drive MacBook Pro 8,2

    - by kizdp
    Good afternoon, this is the first time I participate here as I'm new to Linux. I've been trying to solve the following problem for over a week without any sign of success so I hope there's a much more knowledgeable person here that can give me a solution. I have an early 2011 MacBook Pro (8,2) with Mac OS X running in a SSD. Then, instead of the Optical bay, I have a HDD in where I would like to install Ubuntu to run it natively. I've tried to do the normal installation process, with or without rEFIt, but it seems the problem resides on the communication between the device containing the Ubuntu .iso file and the laptop. It doesn't allow communication with the boot CD or USB drive. It usually says: “Loading bootlogo...” after I click on the “boot from CD, Linux Icon”. After trying several things, I would like to know if I could install Ubuntu on the HDD as an external HDD (using a friend's Window's system) and then simply put it back into my laptop so as to become an Internal HDD again. I guess, I would have to reinstall many drivers and so on, but would this approach work? Thanks in advance and sorry for this huge block of text

    Read the article

  • recovering raid 0 hard disk

    - by Hiawatha
    I bumped to a huge (for me) problem. I was running dual boot system (win 7 / linux) and at some point I decided to test fedora ( I am new in Linux ). My hard disk conf: 3 hard disks each 1 TB, 2 set to raid 0 with windows running on it and 1 for linux. After installing it from live usb I found out that windows 7 is not in grub anymore and while booting shows raid error. I installed back Ubuntu and ran Disk Utility and checked now I have one disks (raid 0) failed (READ) error. First has 5 bad sectors and second has 1 bad sector. And now I dont know what to do and how to repair. further I dont know which data i could provide to get help. I tried ntfsfix and got this output: Mounting volume... NTFS signature is missing. FAILED Attempting to correct errors... NTFS signature is missing. FAILED Failed to startup volume: Invalid argument NTFS signature is missing. Trying the alternate boot sector Unrecoverable error Volume is corrupt. You should run chkdsk. #sudo ntfs-3g -o force,rw /dev/sdb /media/windows NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around?

    Read the article

  • Kubuntu 11.10 Lot of Networking problems

    - by Cobraone
    Since I upgrade to 11.10 I have a lot of problems with KDE. First of all there are problems in configuring a static IP address. Just to explain @home I have a normal fiber ADSL and I use a DHCP. When I go to a customer I must insert a static IP address. With ifconfig everything seems ok but there is something wrong in searching DNS names. (I have installed Ubuntu and was going ok again). Now I Have reinstalled again Kubuntu 11.10 and I have the same problem in addition today I have discovered that if I connect to a network in another customer office the desktop freezes and I could only switch between windows with alt+tab. No FN key or right click to open run command works. So i unplugged network (configuration is just DHCP here) and tried on another position in office. It was the same. My Laptop freezes when connected, a fedora 14 of a friend works. So I decided to connect my Galaxy S II as USB network device. Everything is ok for like 3 minutes. When I noticed a little loss of signal again the desktop freezes and i must work (like now) just switching between windows with alt+tab). Additional information: Unplugging network or restarting it via Konsole does not not solve the freezing problem. Every time I must open a console and reboot. Any idea of what tests to do ? Just a recommendation: If I must post here logs or something else please guide me. I use Linux since Ubuntu 9 but I am not an "expert".

    Read the article

  • Laser range finder, what language to use? Beginner advice

    - by DrOnline
    I hope this is the right place. I am a programming beginner, and I want to make a laser range finder, and I need advice about how to proceed etc. In a few weeks I will get a lot of dirt cheap 3-5V lasers and some cheap usb webcams. I will point the laser and webcam in parallel, and somehow use trigonometry and programming to determined distance. I have seen online that others made done it this way, I have purposefully not looked at the details too much because I want to develop it on my own, and learn, but I know the general outline. I have a general idea of how to proceed. The program loads in a picture from the webcam, and I dunno how images work really, but I imagine there is a format that is basically an array of RGB values.. is this right? I will load in the red values, and find the most red one. I know the height difference between the laser and the cam. I know the center dot in the image, I know the redmost dot. I'm sure there's some way to figure out some range there. TO THE POINT: 1) Is my reasoning sound thus far, especially in terms of image analysis? I don't need complete solutions, just general points 2) What I need to figure out, is what platform to use. I have an arduino... apparently, I've read it's too weak to process images. Read that online. I know some C I know some Python I have Matlab. Which is the best option? I do not need high sampling rates, I have not decided on whether it should be automated or whether I should make a GUI with a button to press for samples. I will keep it simple and expand I think. I also do not need it to be super accurate, I'm just having fun here. Advice!

    Read the article

  • Fail to boot after installation onto ASUS PC 1015PX

    - by strugglingbadly
    My new ASUS 1015PX has the usual Windows on the SDA1 partition - 100Gb, followed by SDA2 - 15Gb - as the recovery partition for Windows, and SDA3 with 183Gb for drive D:\ for windows. ASUS uses SDA4 - 19Mb for it's own use. 11.10 on an USB will load Ubuntu on a try basis and it seems OK, but every time I attempt an install, Ubuntu quickly shuts down and the restart process begins. This repeats endlessly. I've tried 10.04 Netbook Remix but that will not boot at all with the machine reporting - unknown keyword in config file gfxboot vesamenu.c32: not a COM32R image. I've gone through the above about 6 times each with the same results. I have also tried the above with the partitioning unchanged, and using gparted, with SDA3 formatted to ext4, windows D:\ reduced to 8Gb providing a 175Gb unallocated space - all to no avail. Further information: During my attempt to load 11.10, I notice that on the page which offers 3 options of loading, the first in the list includes the statement 'install INSIDE windows...' whereas the on line help shows 'install ALONGSIDE windows...'. (my caps for emphasis) I have double checked that I am using the correct download - not the install within windows option.

    Read the article

  • Doubt related to PHP Cookies

    - by Richa
    Hey guys! I have a doubt, I will appreciate if you can clear it . COOKIES What are cookies? When described as entities, which is how cookies are often referenced in conversation, you can be easily misled. Cookies are actually just an extension of the HTTP protocol. Specifically, there are two additional HTTP headers: Set-Cookie and Cookie.The operation of these cookies is best described by the following series of events: Client sends an HTTP request to server. Server sends an HTTP response with Set-Cookie: foo=bar to client. Client sends an HTTP request with Cookie: foo=bar to server. Server sends an HTTP response to client. Thus, the typical scenario involves two complete HTTP transactions. In step 2, the server is asking the client to return a particular cookie in future requests. In step 3, if the user’s preferences are set to allow cookies, and if the cookie is valid for this particular request, the browser requests the resource again but includes the cookie. Now my question is....... why you cannot determine whether a user’s preferences are set to allow cookies during the first request????

    Read the article

  • CodePlex Daily Summary for Saturday, August 23, 2014

    CodePlex Daily Summary for Saturday, August 23, 2014Popular ReleasesDIII Save Editor: ROS Alpha 1.2.14.100: initial Ros alpha release please report all bugsSEToolbox: SEToolbox 01.044.014 Release 2: Fixed Ship name not saving. Fixed broken cubes view Bug. Fixed cast VRage.MyFixedPoint error when opening games with Meteors. Added checkbox when Importing 3d model to Export ship, to fill it as solid.CS-Script Source: Release v3.8.5: Fixed problem with the warnings getting hidden in case of the successful compilation cs-script.7z - CS-Script Suite (binaries, documentation, samples) cs-script.ExtensionPack.7z - CS-Script Extension Pack (additional binaries and samples) cs-scriptDocs.7z - CS-Script DocumentationOutlook 2013 Backup Add-In: Outlook Backup Add-In 1.3: Changelog for new version: Added button in config-window to reset the last backup-time (this will trigger the backup after closing outlook) Minimum interval set to 0 (backup at each closing of outlook) Catch exception when data store entry is corrupt Added two parameters (prefix and suffix) to automatically rename the backup file Updated VSTO-Runtime to 10.0.50325 Upgraded project to Visual Studio 2013 Added optional command to run after backup (e.g. pack backup files, ...) Add...babelua: 1.6.7.0: V1.6.7.0 - 2014.8.21New feature: add a file search window ( ctrl+1 or ALT+L ), like The file search in VC Assistant; Stability improvement: performance improvement when BabeLua load/unload; performance improvement when debugger load lua files;Open NFe: RDI Open NFe 3.0 (alpha): Atualização para o layout 3.10 da NFe.MSSQL Deployment Tool: Microsoft SQL Deploy Tool v1.3.1: MicrosoftSqlDeployTool: v1.3.1.38348 What's changed? Update namespace and assembly name. Bug fixing.SharePoint 2013 Search Query Tool: SharePoint 2013 Search Query Tool v2.1: Layout improvements Bug fixes Stores auth method and user name Moved experimental settings to Advanced boxCtrlAltStudio Viewer: CtrlAltStudio Viewer 1.2.2.41183 Alpha: This alpha of the CtrlAltStudio Viewer provides some preliminary Oculus Rift DK2 support. For more details, see the release notes linked to below. Release notes: http://ctrlaltstudio.com/viewer/release-notes/1-2-2-41183-alpha Support info: http://ctrlaltstudio.com/viewer/support Privacy policy: http://ctrlaltstudio.com/viewer/privacy Disclaimer: This software is not provided or supported by Linden Lab, the makers of Second Life.HDD Guardian: HDD Guardian 0.6.1: New: package now include smartctl 6.3; Removed: standard notification e-mail. Now you have to set your mail server to send e-mail alerts; Bugfix: USB detection error; custom e-mail server settings issue; bottom panel displays a wrong ATA error count.VG-Ripper & PG-Ripper: VG-Ripper 2.9.62: changes NEW: Added Support for 'MadImage.org' links NEW: Added Support for 'ImgSpot.org' links NEW: Added Support for 'ImgClick.net' links NEW: Added Support for 'Imaaage.com' links NEW: Added Support for 'Image-Bugs.com' links NEW: Added Support for 'Pictomania.org' links NEW: Added Support for 'ImgDap.com' links NEW: Added Support for 'FileSpit.com' links FIXED: 'ImgSee.me' linksExchange Database Recovery With and Without Log Files is Possible: Exchange Recovery Application: This Exchange Recovery Software comes with free trial edition which helps users to inspect the working capability of the recovery process. Download free demo version and repair inaccessible mailboxes from EDB file without any obstructions.Linq 4 Javascript: Version 2.4: Minor Changes Made Added Count() and Count(with where clause) Distinct will now use a dictionary instead of a custom dictionary object Organize the unit tests. The variable names will actually make sense and won't be 2 letters. SelectMany will now use the queryable logic.Office / SharePoint 2013 Continuous Integration with TFS 2012: 1.1.0.1: Fixed the following issues in TfsDropDrownloader: Updated to make it work with VS 2013 (including VS 2013 updates) in addition to VS2012. Extend the timeout of downloading drops from 100 seconds to 1 hour. Added more trouble shooting information in the output.CRM Solution CommandLine Helper: CRM Solution Cmd Helper 1.0.0.4: Includes : - Bug fix = Export argument validation : check directory path existence (thanks mszlapa)Office To PDF: OfficeToPDF 1.4: Adds support for additional file types: * mpp (requires MS Project >= 2010) * vsdx, vsdm (requires MS Visio >= 2013) * csv * odt, odc, odp * pot, potm, potx Improves stability and clean removal of COM objects. Adds new flags: * /verbose - to be more verbose when running * /markup - to allow document markup in the PDF when converting Word documents * /excel_max_rows - adds a maximum limit on the number of rows a worksheet can contain when converting Excel documents * /pdfa - crea...MongoRepository: MongoRepository 1.6.6: Installing using NuGet (recommended)MongoRepository is now a NuGet package for your convenience. Step-by-step instructions can be found in Installing MongoRepository using NuGet Installing using BinariesYou can also choose to download the binaries instead of using NuGet. There are 2 downloads: mongorepository_full.x.x.x contains all binaries required (MongoRepository and the 10gen C# driver) mongorepository.x.x.x contains only the MongoRepository binary Make sure you reference MongoReposit...Cryptography Enumerations JavaScript Shell: Cryptography Enumerations JavaScript Shell 1.0.0: First ReleaseCMake Tools for Visual Studio: CMake Tools for Visual Studio 1.2: This release adds the following new features and bug fixes from CMake Tools for Visual Studio 1.1: Added support for CMake 3.0. Added support for word completion. Added IntelliSense support for the CMAKEHOSTSYSTEM_INFORMATION command. Fixed syntax highlighting for tokens beginning with escape sequences. Fixed issue uninstalling CMake Tools for Visual Studio after Visual Studio has been uninstalled.GW2 Personal Assistant Overlay: GW2 Personal Assistant Overlay 1.1: Overview1.1 is the second 'stable' release of the GW2 Personal Assistant Overlay. This version includes just a couple of very minor features and some minor bug fixes. For details regarding installation, setup, and general use, see Documentation. Note: If you were using a previous version, you will probably want to copy over the following user settings files: GW2PAO.DungeonSettings.xml GW2PAO.EventSettings.xml GW2PAO.WvWSettings.xml GW2PAO.ZoneCompletionSettings.xml New FeaturesAdded new "No...New Projects3D Projectile: A 3D Projectile program showing the motion of a ballASP.NET Web Application Starter Kit: This project template is an ASP.NET solution skeleton for a typical web application or single-page application (SPA).Behaving - Behaviour Tree for C#: Behaviour is a Behaviour Tree implementation in C#.Kinect Stream Saver Application _SDK 2: This application is developed based on a sample called "ColorBasics-D2D C++" developed by Microsoft corporation. (Compatible with SDK 2: K4W v2 Dev Preview)MVC Bootstrap Paginator: The MVC Bootstrap Paginator is lightweight and easy to use. It's works out of the box and requires minimal configuration.NuGet Reference Switcher: NuGet Reference Switcher is a Visual Studio extension which can be used to automatically switch NuGet DLL references to project references and vice-versa. QKit: A WP8.1 library that provides various controls and classes that will help developers quickly and easily augment their apps to behave more like native apps.SharePoint 2013 Document Icon Linker: Links the document icon in library views to the document.SharePoint Autocomplete People Search: SharePoint People SearchWADM: WADM

    Read the article

  • Having trouble installing Bradcom STA driver

    - by user192881
    I just installed Ubuntu and love it so much, its so fast now. But I have a problem connecting to the internet. I checked and saw I have to install the driver Broadcom STA wireless driver but every time I do try to install it it says: Sorry, installation of this driver failed. Please have a look at the log files for details: /var/log/jockey.log I went to the terminal and copy and pasted the log file name. and when I did it, it said I have no permission to access this file. I checked on the forums that I have to be on a wired connection. So I plugged my laptop into my router and I got internet then tried to install the driver again. And it was loading then when it got to the end the same message popped up. Also I have one of those little USB router things you plug into the computer and it gives you internet I have been using that but its to slow. So I want to use the one in my computer but cant. Also I tried the command: sudo modprobe wl and when i type that command in it says: FATAL: Module wl not found Also I'm using Ubuntu 12.04

    Read the article

  • File Adapter FileName Macros

    - by IntegrationOverload
    I can never find these when I need them...   Macro name Substitute value %datetime% Coordinated Universal Time (UTC) date time in the format YYYY-MM-DDThhmmss (for example, 1997-07-12T103508). %datetime_bts2000% UTC date time in the format YYYYMMDDhhmmsss, where sss means seconds and milliseconds (for example, 199707121035234 means 1997/07/12, 10:35:23 and 400 milliseconds). %datetime.tz% Local date time plus time zone from GMT in the format YYYY-MM-DDThhmmssTZD, (for example, 1997-07-12T103508+800). %DestinationParty% Name of the destination party. The value comes from the message context property BTS.DestinationParty. %DestinationPartyQualifier% Qualifier of the destination party. The value comes from the message context property BTS.DestinationPartyQualifier. %MessageID% Globally unique identifier (GUID) of the message in BizTalk Server. The value comes directly from the message context property BTS.MessageID. %SourceFileName% Name of the file from where the File adapter read the message. The file name includes the extension and excludes the file path, for example, Sample.xml. When substituting this property, the File adapter extracts the file name from the absolute file path stored in the FILE.ReceivedFileName context property. If the context property does not have a value, for example, if a message was received on an adapter other than the File adapter, the macro will not be substituted and will remain in the file name as is (for example, C:\Drop\%SourceFileName%). %SourceParty% Name of the source party from which the File adapter received the message. %SourcePartyQualifier% Qualifier of the source party from which the File adapter received the message. %time% UTC time in the format hhmmss. %time.tz% Local time plus time zone from GMT in the format hhmmssTZD (for example, 124525+530).

    Read the article

  • Dell Powerdge840 2.4GHz 64 bit quad core

    - by newb64bit
    I am having an issue, where I have changed the boot order to cdrom and turned off hd boot all together and still my system is unable to detect ubuntu and claims, no boot device found. Some additional information: When this same cd is inserted and dell is booted into win 2003 server (which is what is installed on this machine), it detects the cd drive but not the cd at all (keeps asking me to insert disc) I have also created a bootable flash drive using LinuxLive USB creator and when this is selected in boot order again am told no boot device detected. I was speaking to dell and they suggested perhaps there are no drivers on the actual ubuntu installation for the hardware on this Dell and hence the failure of this dell to detect the ubuntu cd. Now, I don't know too much about computers, but this last bit confused me a bit. If the system detects the hardware (when it is booting it sees the cd rom and in bios it sees when the flash drive is connected), then shouldn't it be able to read what is on those drives? However, if there is some firmware or software install that needs to happen, could someone please tell me where to find the correct drivers for ubuntu and dell poweredge to work together? Shall I be installing the desktop version or the server edition, also, 32 bit or 63 bit? Thank you in advance.

    Read the article

  • Is text-only mode a saving or a problem for battery savings?

    - by Robottinosino
    A friend is flying to the US from Europe and asked me a very thought-provoking question, which I am not remotely able to answer with substance so I am asking it here: How to absolutely maximise battery life on an Ubuntu (laptop) install? do not rush to mark this as duplicate, there is an important point here: does -GNOME- help or worsen battery life? Let me provide some context: The only task he needs to perform is: edit text files in Vim. He is unsure whether running GNOME will drain his battery life more or actually save him some battery life given the smarts of GNOME's power management features like "switch this peripheral to -power save- after X minutes..." (GNOME might just be a configuration front-end for settings that are governed by command-line utils for all I know?) He could perfectly well boot the system in text-only mode and use the automatic 6 virtual consoles for his needs, if that's a saving at all over running tmux (I think so because of all the smart buffering/history/etc the latter does by default?) Exactly how would you advise him to run his laptop during his flight? What I told him already: power off WiFi in the BIOS, not from the "GUI" power off Bluetooth switch off the courtesy light and use low monitor brightness play music off of his phone, not mp3blaster do not use his tiny portable mouse (and do not attach any other USB gimmicks like "screen light", etc) stop development services he will not be using, especially apache2, tomcat, dovecot, postgresql, etc. Potentially: - switch off his cron jobs? (he does an rsync + tar + 7za of his "work in progress" every so often) I think the above is standard stuff one could get off StackExchange, and with many duplicates... the core of this question is, I think: __ will running Ubuntu in text-only mode be a saving in terms of battery life or a problem? why? (provide some technical arguments) __ I think it will be a saving but I am also scared about "other things" detecting and enabling advanced chipset power management features only when some services are started.. and fear these "services" may be off in text-only mode?

    Read the article

  • List of Asus U46 laptop troubles with Ubuntu 12.04

    - by Cybertib
    I've bought my ASUS U46 last february. I would like to make it work better with Ubuntu 12.04. Note taht I was forced to install Ubuntu 12.04 (before its publication) by ethernet. After a successfull install, several problem remain unfixed such as : USB 3 just does not work correctly. Can be fixed, but I didn't succeed yet. Nvidia Optimus (means that you can use Intel Chipset or the Nvidia GeForce) is possible to use thanks to BumbleBee project. It seems to work, though. But Nvidia tools still say they don't see any Nvidia driver installed. Battery duration can be optimised by using Laptop-tools. Any standby state lead to a X server crash. A good CTRL+ALT+F1 login and "shutdown -r" avoids a brutal power off. And since few weeks, I have some bug reports right after boot about "unattended-upgrade", and dpkg troubles after any apt-get install or update (Linux kernel doesn't compile anymore), ... Are there any ways to fix those troubles ? I would need a bit of assistance, in fact. Thank you for you help, Sincerly yours, Thibault

    Read the article

< Previous Page | 346 347 348 349 350 351 352 353 354 355 356 357  | Next Page >