Search Results

Search found 21884 results on 876 pages for 'external address'.

Page 358/876 | < Previous Page | 354 355 356 357 358 359 360 361 362 363 364 365 | Next Page >

OpenSWAN KLIPS not working

- by bonzi

I am trying to setup IPSec between 2 VM launched by OpenNebula. I'm using OpenSWAN for that. This is the ipsec.conf file config setup oe=off interfaces=%defaultroute protostack=klips conn host-to-host left=10.141.0.135 # Local IP address connaddrfamily=ipv4 leftrsasigkey=key right=10.141.0.132 # Remote IP address rightrsasigkey=key ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel I'm able to establish the connection with netkey but klips doesnt work. ipsec barf shows #71: ERROR: asynchronous network error report on eth0 (sport=500) for message to 10.141.0.132 port 500, complainant 10.141.0.135: No route to host [errno 113, origin ICMP type 3 code 1 (not authenticated)] Tcpdump shows 22:50:20.592685 IP 10.141.0.132.isakmp > 10.141.0.135.isakmp: isakmp: phase 1 I ident 22:50:25.602182 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:26.602082 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:27.601985 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 ipsec eroute shows 0 10.141.0.135/32 -> 10.141.0.132/32 => %trap What could be the problem?

Read the article
Including existing ISA server into domain

- by user23419

Is there any problem or pitfall including ISA server into domain after ISA was installed and configured and worked for a while? All the rules at the moment are based upon IP addresses, All Users. Addendum 1 ISA is an edge firewall, so it is connected to one Internal network (this is where domain is) and to the Internet provider (External Network). Addendum 2 I'm absolutely sure ISA should be a member of the domain.

Read the article
Is there an easy way to mass-transfer all files between two computers?

- by Raven Dreamer

I'm currently visiting my parents for the Christmas holidays, and as I'm sure is the case of many in the post-tech generation, my arrival brings with it the assumption of personal tech support. I've been tasked with setting up my folks' new computer, and they want to make sure all their files, yes, all their files, get transfered over to the new device. Short of manually dragging each folder in the C:/ directory onto an external hard drive and then out onto the recipient computer, is there an easier / faster way to do this?

Read the article
Apache httpd workers retry

- by David Newcomb

I have an Apache httpd web server running mod_proxy and mod_proxy_balancer. The whole of /somedir is sent to 2 worker machines which service the requests using the round robin scheduler. Each worker machine is running IIS but I don't think that is important. I can demonstrate the load balancer working by repeatedly requesting a single page which contains the IP address of the machine and can see that it switches from one to the other in a predictable round robin fashion. If I switch off one of the IIS servers and start requesting the same page then each page only contains the IP address of the machine that is up. However, if I start IIS and don't run my IIS application then /somedir returns 500 (as it should). I've added 500 to the failonstatus (Apache 2.4) so when it hits the error Apache places the worker machine into error state. Apache still returns the proxy error to the client though. How can I make Apache catch the proxy failure and retry using a different worker in the same way that a connection failure does. Update There is almost the same question asked in StackOverflow so joining them together. http://stackoverflow.com/questions/11083707/httpd-mod-proxy-balancer-failover-failonstatus-transperant-switching

Read the article
Need to have access to my office PC from my laptop hopping through two VPN servers

- by Andriy Yurchuk

Here's the illustration of what I have ( http://clip2net.com/s/2fvar ): My office PC with it's IP of 123.45.e.f. Office VPN, which I will connect to from my VPS to get to my office PC. My own VPS, which I use as a: client to connect to office VPN (through vpnc, which creates a tun0 with 123.45.c.d IP address); VPN server my laptop can connect to (OpenVPN, tun1, 10.8.0.1) My own laptop I will use as a VPN client to connect to VPS OpenVPN server (will create a tun0 with 10.8.0.2 IP address) Now what I have to do is to allow my laptop to connect to at least my office PC, but preferably to all the 123.45.x.x subnet. Please advice on how to best configure OpenVPN, routing, iptables or whatever else is needed on my VPS so that my laptop could gain access to my office PC. P.S. The reason I'm hopping through my VPS is that being connected to the office WiFi I cannot access my office PC and I cannot connect to office VPN (which is another way to access my office PC). The only way to access my PC from office WiFi I have is hopping though an outside network.

Read the article
How do you change a Cisco ASA 5510 management interface?

- by Sam Sanders

I want to add a redundant interface to my Cisco ASA 5510. The management interface is currently using Ethernet0/1 (10.1.25.254/24) one of the interface I want to use for the redundant interfaces. So I wanted to setup Management0/0 as the new management interface. The other interface I want to use is Ethernet0/2 (10.1.0.254/24) for the redundant interface. The Ethernet0/3 (10.1.251.5/24) interface is not going to be part of the redundant interface. I gave the Management0/0 an IP address of 10.1.254.5, and was able to connect a win7 box to Management0/0 and use 10.1.254.5 as a gateway; and ping another address on the (10.1.251.0/24) network, but I can't ping the interface (10.1.254.5) itself. I also can't use ASDM/SSH to log onto the ASA at 10.1.254.5. I setup rules in Configuration Device Management Management Access ASDM/HTTPS/Telnet/SSH. That look like the original rules for the Ethernet0/1 interface. The last thing I can think to try would be to change the Configuration Device Management Management Access Management Interface. I'm a bit nervous about changing it, the description of it is a bit vague. What it's going to do if I change it? What is the correct way to change a management interface?

Read the article
Troubleshooting wireless client-bridged networks between two DD-WRT routers?

- by KronoS

I recently purchased a Buffalo N600 wireless router which came with DD-WRT pre-installed. I want to take my old wireless router a Linksys WRT54GL, also with DD-WRT pre-installed, and use it as a wireless bridge for my HTPC and Blu-Ray Player in the other room. I other words, I'm trying to connect to WIRED networks via the wireless on the routers. I followed eactly the instruction from DD-WRT's manual for 'Client Bridged' however I'm still not able to connect to two routers correctly, when the encryption is enabled (WPA2-Personal Mixed) however I am able to connect the two routers when there is NO encryption. I've checked, double checked, and triple checked that EVERYTHING is the same on BOTH routers: Routers 1 & 2 Encryption: WPA2-Personal Mixed Wireless Mode: G-Only Wireless Channel: 6 Subnet Mask: 255.255.255.0 Subnet: 192.168.1.0/254 SSID: Krono$ Primary Router #1 (Buffalo N600) IP Address: 192.168.1.1 Firewall: Enables w/ defaults DCHP: Enabled as DHCP Server Secondary Router #2 (Linksys WRT54GL) IP Address: 192.168.1.2 Firewall: Disabled as per DD-WRT instructions I'm looking for any configurations that I may have missed, or settings that may need to happen in order for this work.

Read the article
How do I make netdiag work?

- by Mohamed Abobakr

I'm trying to run the netdiag command to troubleshoot the internet connection but when I run it in cmd I get the following message: 'netdiag' is not recognized as an internal or external command, operable program or batch file. Also, I have tried typing "net diag", which gives me a syntax error, but that NET command seems to be something completely different. Searching on google for answers gives me results that deal with Windows Server 2003; I'm on a Windows XP machine.

Read the article
Why is Hard Disk Access Slow Through a Virtual Machine?

- by Earl

Why is throughput to an external hard drive from a virtual machine much slower than through the host? Access is generally 30MB/sec from the host and 4MB/sec frm the client. Is this normal?

Read the article
When would a persistent route not be an active route?

- by alnorth29

I've added a persistent route to our Windows Server 2003 box using "route -p add". After a reboot the "route print" gave this: Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.91.131.1 10.91.131.9 20 10.88.0.0 255.255.255.252 10.88.0.1 10.88.0.1 30 10.88.0.1 255.255.255.255 127.0.0.1 127.0.0.1 30 10.91.131.0 255.255.255.0 10.91.131.9 10.91.131.9 20 10.91.131.9 255.255.255.255 127.0.0.1 127.0.0.1 20 10.255.255.255 255.255.255.255 10.88.0.1 10.88.0.1 30 10.255.255.255 255.255.255.255 10.91.131.9 10.91.131.9 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 224.0.0.0 240.0.0.0 10.88.0.1 10.88.0.1 30 224.0.0.0 240.0.0.0 10.91.131.9 10.91.131.9 20 255.255.255.255 255.255.255.255 10.88.0.1 10.88.0.1 1 255.255.255.255 255.255.255.255 10.91.131.9 10.91.131.9 1 Default Gateway: 10.91.131.1 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 10.88.0.0 255.255.255.0 10.88.0.2 1 The route I added is listed as a persistent route, but not an active one. Why might this be the case? The route in question is for an OpenVPN connection, would that have anything to do with it?

Read the article
Two wireless NICs on a MacBook - can I bind all VPN traffic to one, and everything else to another?

- by Ben Aston

I frequently connect to my workplace over a VPN. I would like to continue watching videos from, say YouTube, whilst I work on the VPN, without degrading the available VPN bandwidth (say for an RDP session). Can I configure a second NIC to deal with only the VPN traffic, with everything else going over the primary? Specs as requested: Macbook Pro, OSX Snow Leopard, using the built in OSX VPN connectivity, the in-built airport card and a USB external wifi adapter.

Read the article
configuration of zend frame work in ubuntu

- by Rahul Mehta

Hi, I have created a project zfapi by zf command in ubuntu. Now http://myserverpath.com/zfapi/ gives me listing of folder public application and others. http://myserverpath.com/zfapi/public give me the index page index.php. and i have made the UserController.php in application/controllers but by http://myserverpath.com/zfapi/user/ is saying user not found. what configuration i need to set for running it proper. I had set my /etc/apache2/apache2.conf added the following in the last . <VirtualHost *:80> DocumentRoot "/var/www/mypath/zfapi" <Directory "/var/www/mypath/zfapi"> Order allow,deny Allow from all AllowOverride all </Directory> </VirtualHost> is giving me this error while restarting server. [Sat Jan 08 13:32:53 2011] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Sat Jan 08 13:33:03 2011] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results what this i should do .?

Read the article
Configure Domino to use SMTP routing and hMailServer

- by Sébastien Lachance

I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

Read the article
SSL Connection Error

- by toffee.beanns

I have purchased a comodo ssl cert and have submitted the Certificate Signing Request (CSR) generated by my server to the ssl management site. With the 3 files it returned me with, - AddTrustExternalCARoot.crt - PositiveSSLCA2.crt - www_mydomainname_com.crt I have uploaded them to my /etc/ssl/ssl-certs folder and have updated my virtual host in my sites-available and restarted accordingly. NameVirtualHost 107.167.120.195:80 #sample ip address NameVirtualHost 107.167.120.195:443 #sample ip address ......... #normal http virtual host (working well) <VirtualHost 107.167.120.195:443> ServerAdmin [email protected] ServerName mydomainname.com ServerAlias www.mydomainname.com DocumentRoot /var/www/mydomainname SSLEngine on SSLCertificateFile /etc/ssl/ssl-certs/www_mydomainname.com.crt SSLCertificateKeyFile /etc/ssl/ssl-certs/server.key SSLCertificateChainFile /etc/ssl/ssl-certs/PositiveSSLCA2.crt </VirtualHost> I have also enabled ran 'a2enmod ssl' and it's enabled. This is the error I get when I access the webpage https in chrome: SSL connection error Error code: ERR_SSL_PROTOCOL_ERROR Unable to make a secure connection to the server. This may be a problem with the server, or it may be requiring a client authentication certificate that you don't have. I have also checked out my apache log files and there seems to be an error saying that the Common Name (CN) is not the same as the server. RSA server certificate CommonName (CN) `www.mydomainname.com' does NOT match server name!? and Invalid method in request \x16\x03\x01 What should I do?

Read the article
Xen Server Guest Network configuration?

- by GeekTantra

I am trying to install Ubuntu Server as a domU (Guest) on Citrix XenServer. Everything works fine but I am not able to access the internet from the guest. Is there any specific thing that I need to do to configure the network for the Guest. I have two NICs, 1 has an external IP and the other has an internal IP.

Read the article
Window 7 + SVN permission problem

- by acidzombie24

In tortoisesvn i get the error Can't create directory 'C:\dev\repo\subfolder\db\transactions\49-1g.txn': ... I used robocopy (i cant remember if i used /copyall) to copy the files onto an external drive then i copied it back after a format. Now ATM i cannot commit. How do i fix this?

Read the article
Port 22 is not responding

- by Emanuele Feliziani

I'm trying to make the jump to VPS from shared hosting for better performances and greater flexibility, but am stuck with the fact that I can't access the machine via ssh. First of all, the machine is a CentOS 6.3 cPanel x64 with WHM 11.38.0. Sshd is running (it appears in the current running processes). Making a port scan I see that port 22 is not responding. Port 21 is, but I am not able to access the machine via ftp (I think it's a security measure, but I don't know where to disable/enable it). So, I'm stuck in WHM and have no way to access the configuration of the machine, neither via ssh nor with ftp/sftp. When trying to connect with ssh via Terminal I only get this: ssh: connect to host xx.xx.xxx.xxx port 22: Operation timed out I also tried to access with the hostname instead of the IP address and it's the same. There seem to be no firewall in WHM and I have whitelisted my home IP address to access ssh, though there were no restrictions in the first place. I have been wandering through all the settings and options in WHM for several hours now, but can't seem to find anything. Does anybody have a clue as to where I should start investigating? Update: Thanks everyone. It was in fact a matter of firewall. There was a firewall not controlled by the WHM software. I managed to crack into the console from the vps control panel (a terrible, terrible java app that barely took my keyboard input) and disabled the firewall altogether running service iptables stop so that I was able to access the console via ssh with the terminal. Now I will have to set up the firewall again because the command I ran looks like having completely wiped the iptables. Can you recommend any newby-friendly resource where I can learn how to go about this and what should I block? Or should I just go with something like this: http://configserver.com/cp/csf.html ? Thanks again to everyone who helped me out.

Read the article
WWNs,WWPNs and Fibre Channel addresses

- by user238230

Lots of contradictory on these subjects and I don't know why. My first question is about the 64 bit WWN. One reference claims the terms WWN and WWPN are synonymous. An online source seems to refute this. They say: A WWPN (world wide port name) is the unique identifier for a fibre channel port where a WWN (world wide name) the unique identifier for the node itself. A good example is a dual port HBA. There will be two WWPN's (one for each port) and only a single WWN for the card itself. Question #1: Which is correct? I’m almost positive I read that every “Port” has a WWN. My next question is about the 24 bit FC address that is dynamically allocated to a port when it is introduced to the switch. The Domain ID field is defined as: "a unique number provided to each switch in the fabric." Question #2: Do Domain IDs only apply to switch ports? For example what would the Domain ID be for a HBA? None? The same as the switch port it is connected to? Question #3: My last question is about the Name Server of a switch. A book example shows the routing of a message through the switch. It uses the WWNs of the source and destination ports to route the message. I am assuming that the Name Server must associate the WWN and the FC address in some way in order to route the message, correct?

Read the article
HP DL380 using HP NC522SFP NIC shows supported link modes: not reported

- by MikeS

When using ethtool on this NIC, the supported link modes show "not reported". Any idea why this is the case? Settings for eth0: Supported ports: [ FIBRE ] Supported link modes: Not reported Supported pause frame use: Symmetric Supports auto-negotiation: No Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 1 Transceiver: external Auto-negotiation: off Supports Wake-on: g Wake-on: g Current message level: 0x00002000 (8192) hw Link detected: yes

Read the article
802.11g -> wired ethernet bridging not working

- by Malachi

Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

Read the article
Recovering files using Recuva

- by Nev Meek

I'm currently using Recuva to recover some files from an external NTFS disk. It finds the files I'm interested in during it's analysis phase (when tools like test-disk fail to find them at all) and reports them as "Not-deleted" and a big green marker to signify 100% chance of recovery. However when it tries to recover the files I get a "the system could not find the file specified" message. Is there any easy way to recover non-deleted files off of a disc that I can no longer simply access through explorer?

Read the article
Configure IIS site to work with host header & hosts file entry

- by HarveySaayman

I'm I bit of an IIS / Web noob (I'm a C# backend service / winforms dev) so please bare with me :-) I've set up a site in IIS on my local dev machine. In the bindings section of the site ive added 4 bindings, all 4 for http: Host Name Port IP Address blog.sourcecube.co.za 26581 * www.blog.sourcecube.co.za 26581 * blog.sourcecube.co.za 26581 127.0.0.1 www.blog.sourcecube.co.za 26581 127.0.0.1 in my hosts file (drivers\etc\hosts), i've added the folling entries: 127.0.0.1 blog.sourcecube.co.za 127.0.0.1 www.blog.sourcecube.co.za when i ping my domain name from the command line it does in fact resolve to the loopback address, 127.0.0.1. So what I'm expecting to happen when i navigate to blog.sourcecube.co.za in my browser is for it to resolve to 127.0.0.1, and when the request hits IIS, it should know which site to serve because of the host header? But when i navigate to blog.sourcecube.co.za, i get an "Unable to connect, Firefox can't establish a connection to the server at blog.sourcecube.co.za" error. What am I doing wrong? --- UPDATE --- Navigating to blog.sourcecube.co.za:26581 from my browser works... I'd like get it working without specifying the port number though.

Read the article
isa 2004 - banned site rule cause slow internet

- by Holian

Hi Gods, We have windows server 2003 with isa 2004. Our clients uses internet with proxy. We have two isa rule: order name action protocolls from/listener to condition 1. trafic ALLOW all outbound all networks all networks all users 2. FTP ALLOW FTP Server EXTERNAL/INTERNAL/Local host 10.1.1.1 So we have to "bann" a few webpage (like facebook, youtube...etc...), so we make a new rule 0. banned DENY HTTP internal denied pages all users In the denied pages we have the *.facebook.com domain set. After we enable this rule, the entire internet slows down. The banning rule works well, redirect to an internal site, but the other sites.... If i open a page..it normally takes 3-10 sec to load, but after this rule this time is: 2-4 minutes. In the monitor / logging menu we got a few FAILED CONNECTION ATTEMPT like: Log type: Web Proxy (Forward) Status: 304 Not Modified Rule: All local traffic Source: Internal ( 10.1.1.1:0 ) Destination: External ( 172.24.28.22:3128 ) Request: GET http://www.konyvelozona.hu/wp-content/uploads/nyugdijas-holgy-2.jpg Filter information: Req ID: 17270b72 Protocol: http User: anonymous Additional information Client agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.3072... Object source: Verified Cache Processing time: 9047 Cache info: 0x18801002 MIME type: - In the event log we got a few log: Description: The Web Proxy filter failed to bind its socket to 10.1.1.1 port 80. This may have been caused by another service that is already using the same port or by a network adapter that is not functional. To resolve this issue, restart the Microsoft Firewall service. The error code specified in the data area of the event properties indicates the cause of the failure. The failure is due to error: 0x8007271d The Web Proxy filter failed to bind its socket to 127.0.0.1 port 80. This may have been caused by another service that is already using the same port or by a network adapter that is not functional. To resolve this issue, restart the Microsoft Firewall service. The error code specified in the data area of the event properties indicates the cause of the failure. The failure is due to error: 0x8007271d If i tpye: netstat -o -n -a | findstr 0.0:80 then i got, tcp 0.0.0.0:80 0.0.0.0:0 LISTEN 4 udp 0.0.0.0:8031 *.* 2780 udp 0.0.0.0:8082 *.* 2780 Some month ago we installed XMAP, but now we only use mysql. Apache service stopped. In the Xamp port check menu i see: Service POrt Status Apache (http) 80 Process: System Maybee this is the problem? I dont know what should i do now... Thank you folks.

Read the article
How does Tunlr work?

- by gravyface

For those of you not in the US, Tunlr uses DNS witchcraft to allow you to access US-only (and UK-only stuff like BBC radio online) services and Websites like Hulu.com, etc. without using traditional methods like a VPN or Web proxy. From their FAQ: Tunlr does not provide a virtual private network (VPN). Tunlr is a DNS (domain name system) unblocking service. We’re using sophisticated technologies (a.k.a. the Tunlr Secret Sauce ©) to re-adress certain data envelopes, tricking the receiver into thinking the envelope originated from within the U.S. For these data envelopes, Tunlr is transparently creating a network tunnel from your location to our U.S.-based servers. Any data that’s not directly related to the video or music content providers which Tunlr supports is not only left untouched, it’s also not even routed through Tunlr. In order to use Tunlr, you will have to change the DNS address. See Get started for more information. I can't really wrap my head around how this works; I have always assumed that these services performed a geolocation lookup via your client IP. Just really curious as to how this works. EDIT 2 I believe they're only proxying the initial geo check and then modifying the data stream request to include your real IP address so that the streaming is direct, not proxied.

Read the article
Can't authorize a server for Amazon RDS

- by Parris

We are attempting to slowly migrate a website over to AWS among other things. We decided the first thing to move was the database. We have some dedicated server with a different hosting provider. We only have one IP. I am having trouble authorizing the ip so that the old server can connect to RDS. It simply hangs for a while while using the mysql cli, then responds: ERROR 2003 (HY000): Can't connect to MySQL server on 'db.address.us-east-1.rds.amazonaws.com' (110) It did work on my laptop though. I am not quite sure what is wrong. I have a feeling I don't quite understand CIDR/IP. I simply took the ip address and tacked on /32 at the end. Then I gleaned some information that it also has to do with subnet mask? ifconfig reports: 255.255.255.0 I found a calculator and the IP changed a bit and had /24 at the end. That still didn't work. One other note... perhaps i dont know enough about the differences between OS. The hosting provider is using centOS, while our development machines are all ubuntu. Any insight would be extremely helpful! THANKS :)

Read the article

< Previous Page | 354 355 356 357 358 359 360 361 362 363 364 365 | Next Page >