Search Results

Search found 10511 results on 421 pages for 'clear cycle corp'.

Page 362/421 | < Previous Page | 358 359 360 361 362 363 364 365 366 367 368 369  | Next Page >

• Is my Cisco switch port bad?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• Email postfix marked as spam by google

  - by Rodrigo Ferrari

  Hello friends, I searched about this question, found some few answers but no idea how to fix, the problem is that I realy dumb with all this! I configured the postfix and done everything how the install how to told. It send the email, but get marked as spam! The header is this one: Delivered-To: [email protected] Received: by 10.223.86.203 with SMTP id t11cs837410fal; Wed, 12 Jan 2011 04:02:21 -0800 (PST) X-pstn-nxpr: disp=neutral, [email protected] X-pstn-nxp: bodyHash=9c6d0c64fa3a4d663c9968e9545c47d77ae0242e, headerHash=1ab8726bd17a23218309165bd20fe6e0911627cd, keyName=4, rcptHash=178929be6ed8451d98a4df01a463784e6c59b3b4, sourceip=174.121.4.154, version=1 Received: by 10.100.190.13 with SMTP id n13mr537609anf.76.1294833740396; Wed, 12 Jan 2011 04:02:20 -0800 (PST) Return-Path: <[email protected]> Received: from psmtp.com ([74.125.245.168]) by mx.google.com with SMTP id w2si1297960anw.132.2011.01.12.04.02.19; Wed, 12 Jan 2011 04:02:20 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.121.4.154 as permitted sender) client-ip=174.121.4.154; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.121.4.154 as permitted sender) [email protected] Received: from source ([174.121.4.154]) by na3sys010amx168.postini.com ([74.125.244.10]) with SMTP; Wed, 12 Jan 2011 12:02:19 GMT Received: from localhost (server [127.0.0.1]) (using TLSv1 with cipher DHE-RSA-AES256-SHA (256/256 bits)) (No client certificate requested) by brasilyacht.com.br (Postfix) with ESMTP id 87C121290142; Wed, 12 Jan 2011 09:50:29 -0200 (BRST) From: YachtBrasil <[email protected]> Reply-To: Vendas <[email protected]> Cc: YachtBrasil <[email protected]> To: [email protected] Subject: teste Date: Wed, 12 Jan 2011 09:50:29 -0200 Content-Type: text/html; charset=UTF-8 Content-Transfer-Encoding: quoted-printable Content-Disposition: inline MIME-Version: 1.0 Message-Id: <[email protected]> X-pstn-2strike: clear X-pstn-neptune: 0/0/0.00/0 X-pstn-levels: (S: 1.96218/99.81787 CV:99.9000 FC:95.5390 LC:95.5390 R:95.9108 P:95.9108 M:97.0282 C:98.6951 ) X-pstn-settings: 3 (1.0000:1.0000) s cv gt3 gt2 gt1 r p m c X-pstn-addresses: from <[email protected]> [db-null] I'm out of ideas on how to fix this, I think it's dns issue, but I have marked the spf inside my tinydns =( Is there anything I can check to know why this email is marked as spam? Any help will be appreciated! Thanks and sorry for my bad english.

  Read the article

• DCHP and Router load testing

  - by John H

  I manage a campground wifi network with an average of 10 - 60 active users. I have encountered issues where the router starts acting flaky (failing to assign DHCP or failing to pass traffic) without any clear warning (low cpu utilization, etc). I upgraded the router a couple times and ended up with a Netgear ProSafe VPN router that seems to be handling the traffic. The interesting thing is that the Netgear has lower specs than the Buffalo router it replaced, indicating the issue is with the DD-WRT firmware. While I'll be pursuing this issue on the dd-wrt forums, I need a way to test routers. My vision is having 1-2 computers connected on the LAN side and 1-2 computers connected on the WAN side. I want the LAN computers to be generating various type of traffic and connections, as well as requesting DCHP addresses. A few notes: The wireless aspect should be a non-issue. Most clients would connect to a wireless bridge and come into the router through a network cable. I had a monitoring server with Nagios running check_dhcp against the router. This server was connected directly by a network cable, eliminating wifi bridges and other devices from the equation. This question is somewhat related, but not exactly: Load testing wireless LANs I am going to look at IxChariot. While I'd ideally like to use a 1 computer on each side running Linux and preferably free software, I can entertain running Windows, multiple computers, or non-free software. Total bandwidth doesn't seem to be the issue. I can transfer large files all day. Even on the busiest days, the users seemed to only pull ~5Mbps. There is very little "LAN to LAN traffic" and most of it might never have reached the main router. The issue I need to test for seems to be tied to active users, or more appropriately, active sessions. I know active users or active clients is a meaningless term from a router standpoint and wouldn't mind having more appropriate terms to use. Summary: I need a way to test a routers ability in handling traffic from a large number of clients. My current strategy is to purchase a router, deploy it, and see how it fails in the live environment.

  Read the article

• Specifying prerequisites for Puppet custom facts?

  - by larsks

  I have written a custom Puppet fact that requires the biosdevname tool to be installed. I'm not sure how to set things up correctly such that this tool will be installed before facter tries to instantiate the custom fact. Facts are loaded early on in the process, so I can't simply put a package { biosdevname: ensure => installed } in the manifest, since by the time Puppet gets this far the custom fact has already failed. I was curious if I could resolve this through Puppet's run stages. I tried: stage { pre: before => Stage[main] } class { biosdevname: stage => pre } And: class biosdevname { package { biosdevname: ensure => installed } } But this doesn't work...Puppet loads facts before entering the pre stage: info: Loading facts in physical_network_config ./physical_network_config.rb:33: command not found: biosdevname -i eth0 info: Applying configuration version '1320248045' notice: /Stage[pre]/Biosdevname/Package[biosdevname]/ensure: created Etc. Is there any way to make this work? EDIT: I should make it clear that I understand, given a suitable package declaration, that the fact will run correctly on subsequent runs. The difficulty here is that this is part of our initial configuration process. We're running Puppet out of kickstart and want the network configuration to be in place before the first reboot. It sounds like the only workable solution is to simply run Puppet twice during the initial system configuration, which will ensure that the necessary packages are in place. Also, for Zoredache: # This produces a fact called physical_network_config that describes # the number of NICs available on the motherboard, on PCI bus 1, and on # PCI bus 2. The fact value is of the form <x>-<y>-<z>, where <x> # is the number of embedded interfaces, <y> is the number of interfaces # on PCI bus 1, and <z> is the number of interfaces on PCI bus 2. em = 0 pci1 = 0 pci2 = 0 Dir['/sys/class/net/*'].each { |file| devname=File.basename(file) biosname=%x[biosdevname -i #{devname}] case when biosname.match('^pci1') pci1 += 1 when biosname.match('^pci2') pci2 += 1 when biosname.match('^em[0-9]') em += 1 end } Facter.add(:physical_network_config) do setcode do "#{em}-#{pci1}-#{pci2}" end end

  Read the article

• Using IIS7 why are my PNGs being cached by the browser, but my JS and CSS files not?

  - by Craig Shearer

  I am trying to sort out caching in IIS for my site. Basically, I want nothing cached, except for .png, .js, and .css files. At my site level, I opened the HTTP Reponse Headers and used the "Set Common Hedaers..." to set content to expire immediately. I have no Output Caching profiles set at any level in IIS. I clear my browser cache then try accessing my site. When my site requests a PNG file, I see responses like: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Type image/png Date Thu, 12 Apr 2012 21:55:15 GMT Etag "83b7322de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For JS and CSS files, I see responses like: Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 597 Content-Type text/css Date Thu, 12 Apr 2012 21:55:15 GMT Etag "06e45ede15bca1:0" Last-Modified Mon, 02 Nov 2009 17:28:44 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 42060 Content-Type application/x-javascript Date Thu, 12 Apr 2012 21:55:14 GMT Etag "2356302de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET So, why are my PNGs able to be cached, but JS and CSS files not? Then, I go into the Output Caching feature in IIS and set up profiles for .png, .css, and .js files. This updates the web.config file as follows: <caching> <profiles> <add extension=".png" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".css" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".js" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> </profiles> </caching> I do a "precautionary" IISReset then try accessing my site again. For PNG files, I see the following response: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Length 3833 Content-Type image/png Date Thu, 12 Apr 2012 22:02:30 GMT Etag "0548c9e2c5dc81:0" Last-Modified Tue, 22 Jan 2008 19:26:00 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For CSS and JS files, I see the following responses: Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 2680 Content-Type application/x-javascript Date Thu, 12 Apr 2012 22:02:29 GMT Etag "0f743af9015c81:0" Last-Modified Tue, 23 Oct 2007 16:20:54 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 3831 Content-Type text/css Date Thu, 12 Apr 2012 22:02:29 GMT Etag "c3f42d2de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET What am I doing wrong? Have I completely misunderstood the features of IIS, or is there a bug. Most importantly, how do I achieve what I want - that is get the browser to cache only PNG, JS and CSS files?

  Read the article

• Changing Physical Path gives blank homepage

  - by Julie

  I have two websites ASP Classic - www.company.com and www.companytesting.com. At this time of year, company.com is pointed to a folder called website2012 and companytesting.com is pointing to a folder called website2013. The contents of those two folders are almost identical, just minor changes for our season change (which I was supposed to do today - lol). Up until a couple of weeks ago, I was running Windows Server 2003. To update the "live" website, I'd make a copy of the test site folder, and rename it website2013R1, and point the test site there, then point the live site at website2012. We now have Windows Server 2008 R2 64. (I had someone migrate the websites to the new server for me.) The companytesting.com site, when I pointed it to website2013R1, worked fine. The company.com site, when I pointed it to website2013 (which worked just before, for the companytesting.com site) gives an empty page. (i.e. view source = nothing there.) There is nothing in the failed request log when this happens. I can use the Explore button/link (upper right) in IIS7.5 and see all of the files there. If I use the browse button (either in general or on the index.asp page) I get the blank page again. One weirdness about how these are set up is that companytesting.com uses a login (which I think is windows authentication - it's simply a single username and password for staff, and to keep the GoogleBots out of it). Obviously, company.com does not. But redirecting the to website2013r1 kept the login in place. (So I'm not absolutely clear whether that's attached to the folder or to the site. Hitting the company.com site after changing the path did not yield a password request.) The permissions on the folders all seem to be the same, but obviously, I'm missing something. Why isn't changing the physical path working? As is probably obvious, I'm not knowledgeable about servers. I did OK in 2003, but since it's not my main task and I'm buried right now, I have barely looked at 2008. So I may have really stupid questions when you ask me to check something.

  Read the article

• Windows DHCP Server - get notification when a non-AD joined device gets an IP address

  - by TheCleaner

  SCENARIO To simplify this down to it's easiest example: I have a Windows 2008 R2 standard DC with the DHCP server role. It hands out IPs via various IPv4 scopes, no problem there. WHAT I'D LIKE I would like a way to create a notification/eventlog entry/similar whenever a device gets a DHCP address lease and that device IS NOT a domain joined computer in Active Directory. It doesn't matter to me whether it is custom Powershell, etc. Bottom line = I'd like a way to know when non-domain devices are on the network without using 802.1X at the moment. I know this won't account for static IP devices. I do have monitoring software that will scan the network and find devices, but it isn't quite this granular in detail. RESEARCH DONE/OPTIONS CONSIDERED I don't see any such possibilities with the built in logging. Yes, I'm aware of 802.1X and have the ability to implement it long-term at this location but we are some time away from a project like that, and while that would solve network authentication issues, this is still helpful to me outside of 802.1X goals. I've looked around for some script bits, etc. that might prove useful but the things I'm finding lead me to believe that my google-fu is failing me at the moment. I believe the below logic is sound (assuming there isn't some existing solution): Device receives DHCP address Event log entry is recorded (event ID 10 in the DHCP audit log should work (since a new lease is what I'd be most interested in, not renewals): http://technet.microsoft.com/en-us/library/dd759178.aspx) At this point a script of some kind would probably have to take over for the remaining "STEPS" below. Somehow query this DHCP log for these event ID 10's (I would love push, but I'm guessing pull is the only recourse here) Parse the query for the name of the device being assigned the new lease Query AD for the device's name IF not found in AD, send a notification email If anyone has any ideas on how to properly do this, I'd really appreciate it. I'm not looking for a "gimme the codez" but would love to know if there are alternatives to the above list or if I'm not thinking clear and another method exists for gathering this information. If you have code snippets/PS commands you'd like to share to help accomplish this, all the better.

  Read the article

• Anyone else experiencing high rates of Linux server crashes during a leap second day?

  - by Bron Gondwana

  POSTMORTEM Anticlimax: only thing that died was my VPN (openvpn) link to the cluster, so there was an exciting few seconds while it re-established. Everything else was fine. Starting back ntp everywhere. If you look at Marco's blog at http://my.opera.com/marcomarongiu/blog/2012/06/01/an-humble-attempt-to-work-around-the-leap-second - he has a solution for phasing the time change over 24 hours using ntpd -x to avoid the 1 second skip. Give that a go if it matters to you. For the systems I run, the jump isn't a problem. Just today, Sat June 30th - starting soon after the start of the day GMT. We've had a handful of blades in different datacentres as managed by different teams all go dark - not responding to pings, screen blank. They're all running Debian Squeeze - with everything from stock kernel to custom 3.2.21 builds. Most are Dell M610 blades, but I've also just lost a Dell R510 and other departments have lost machines from other vendors too. There was also an older IBM x3550 which crashed and which I thought might be unrelated, but now I'm wondering. The one crash which I did get a screen dump from said: [3161000.864001] BUG: spinlock lockup on CPU#1, ntpd/3358 [3161000.864001] lock: ffff88083fc0d740, .magic: dead4ead, .owner: imapd/24737, .owner_cpu: 0 Unfortunately the blades all supposedly had kdump configured, but they died so hard that kdump didn't trigger - and they had console blanking turned on. I've disabled console blanking now, so fingers crossed I'll have more information after the next crash. Just want to know if it's a common thread or "just us". It's really odd that they're different units in different datacentres bought at different times and run by different admins (I run the FastMail.FM ones)... and now even different vendor hardware. Most of the machines which crashed had been up for weeks/months and were running 3.1 or 3.2 series kernels. The most recent crash was a machine which had only been up about 6 hours running 3.2.21. THE WORKAROUND Ok people, here's how I worked around it. disabled ntp: /etc/init.d/ntp stop created http://linux.brong.fastmail.fm/2012-06-30/fixtime.pl (code stolen from Marco, see blog posts in comments) ran fixtime.pl without an argument to see that there was a leap second set ran fixtime.pl with an argument to remove the leap second NOTE: depends on adjtimex. I've put a copy of the squeeze adjtimex binary at http://linux.brong.fastmail.fm/2012-06-30/adjtimex - it will run without dependencies on a squeeze 64 bit system. If you put it in the same directory as fixtime.pl, it will be used if the system one isn't present. Obviously if you don't have squeeze 64 bit... find your own. I'm going to start ntp again tomorrow. As an anonymous user suggested - an alternative to running adjtimex is to just set the time yourself, which will presumably also clear the leapsecond counter.

  Read the article

• With CentOS 6 and LXC, "ifconfig" is unable to see network interface (but busybox "ifconfig" works fine)

  - by larsks

  I've just started working with LXC under CentOS 6 (via the libvirt adapter). If I create an LXC container, I'm unable to see any network interfaces when using the native system tools: # ifconfig -a # The behavior is very odd; specifying an interface by names yields neither the expected output nor an error message. This is true even for clearly invalid interface names, like this: # ifconfig foo # The ip command exhibits the same behavior. On the other hand, if I use "ifconfig" provided by busybox, everything works as expected: # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:268 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17814 (17.3 KiB) TX bytes:552 (552.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So...what does busybox know that the native tools don't? The libvirt config for this environment is pretty standard; the network definition looks like this: <interface type='network'> <mac address='52:54:00:e0:12:c8'/> <source network='default'/> <target dev='veth0'/> </interface> The full configuration is here if you think it might help. I'm running: lxc-0.7.2-2.el6.x86_64 kernel-2.6.32-71.29.1.el6.x86_64 EDIT Weirder and weirder...it's a display issue, not a functionality issue. I can see the output of ifconfig if I pipe it into anything, so for example: # ifconfig eth0 | cat eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:573 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37914 (37.0 KiB) TX bytes:552 (552.0 b) And in fact even when not piping the output, strace shows that ifconfig is in fact writing the output to file descriptor 1 (aka stdout), so it's not clear why no output is actually showing up. This could be either an LXC or a virsh issue, I guess.

  Read the article

• Windows Server 2008 R2 network adapter stops working, requires hard reboot

  - by Geoff Dalgas

  TL;DR version: Turns out this was a Windows Server 2008 R2 kernel networking bug. After siccing Microsoft support on it, we (eventually) got an unpublished kernel hotfix from Microsoft to address it. If you, too, are experiencing mysterious low-level network driver failures requiring a reboot/bluescreen cycle, you might want that hotfix (or maybe Service Pack 1 whenever it is released, too.) We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps. Switch Virtualization providers On the off chance this was related to Hyper-V in some way (we do host Linux VMs on it), we switched to VMWare Server. No change. Switch host model We've reached the end of our troubleshooting rope and are now formally involving Microsoft support. They recommended changing the host model: http://en.wikipedia.org/wiki/Host_model http://technet.microsoft.com/en-us/magazine/2007.09.cableguy.aspx We did that, and.. we'll see.

  Read the article

• filtering itunes library items by file location

  - by Cawas

  3 answers and unfortunately no solution yet. The Problem I've got way more than 1000 duplicated items in my iTunes Library pointing to a non-existant place (the "where" under "get info" window), along with other duplicated items and other MIAs (Missing In Action). Is there any simple way to just delete all of them and only them? From the library, of course. By that I mean some MIAs are pointing to /Volumes while some are pointing to .../music/Music/... or just .../music/.... I want to delete all pointing to /Volumes as to later I'll recover the rest. Check the image below. Some Background I tried searching for a specific key word on the path and creating smart play list, but with no result. Being able to just sort all library by path would be a perfect solution! I believe old iTunes could do that. PowerTunes can do it (sort by path) but I can't do anything with its list. I would also welcome any program able to handle this, then import and properly export back the iTunes library. Since this seems to just not be clear enough... AppleScript doesn't work That's because AppleScript just can't gather the missing info anywhere in iTunes Library. Maybe we could use AppleScript by opening the XML file, but that's a whole nother issue. Here's a quote from my conversation with Doug the man himself Adams last december: I don't think you do understand. There is no way to get the path to the file of a dead track because iTunes has "forgotten" it. That is, by definition, what a dead track is. Doug On Dec 21, 2010, at 7:08 AM, Caue Rego wrote: yes I understand that and have seem the script. but I'm not looking for the file. just the old broken path reference to it. Sent from my iPhone On 21/12/2010, at 10:00, Doug Adams wrote: You cannot locate missing files of dead tracks because, by definition, a dead track is one that doesn't have any file information. If you look at "Super Remove Dead Tracks", you will notice it looks for tracks that have "missing value" for the location property.

  Read the article

• SSH to an ubuntu machine using avahi

  - by tensaiji

  I have an ubuntu box that I connect to using avahi. Connecting to that box works fine for all services (I regularly use AFP, SSH and SMB on it) but I've noticed that whenever I connect to it from a mac using SSH (and using the ".local" dns name provided by avahi - eg. "ssh .local") SSH tries to connect using ipv6, which for some reason times out (after two minutes) then it tries ipv4 which connects immediately. I'd like to avoid this timeout, as it's really annoying for me and other users - if SSH tried ipv4 first or if ssh over ipv6 worked then that would solve the problem. But so far I've been unable to get either to work (the best I've managed is to specify the "-4" option to SSH to stop it from trying ipv6 at all). I'm using Ubuntu 10.04. Any solution has to be on the server (not the client) as there are multiple clients connecting. A possible complication might be that my LAN is set up to allow link-local ipv6 addresses only, but I have other servers (using Mac OS) that I can SSH into using ipv6) I suspect that the problem could be solved by either preventing avahi from broadcasting the ipv6 address, or by enabling ssh over ipv6, but so far as I can tell avahi is already configured not to broadcast the ipv6 address and sshd is configured to allow ipv6 connections! Here's my /etc/avahi/avahi-daemon.conf (I don't think I've changed anything from the ubuntu defaults) [server] #host-name=foo #domain-name=local #browse-domains=0pointer.de, zeroconf.org use-ipv4=yes use-ipv6=no #allow-interfaces=eth0 #deny-interfaces=eth1 #check-response-ttl=no #use-iff-running=no #enable-dbus=yes #disallow-other-stacks=no #allow-point-to-point=no [wide-area] enable-wide-area=yes [publish] #disable-publishing=no #disable-user-service-publishing=no #add-service-cookie=no #publish-addresses=yes #publish-hinfo=yes #publish-workstation=yes #publish-domain=yes #publish-dns-servers=192.168.50.1, 192.168.50.2 #publish-resolv-conf-dns-servers=yes #publish-aaaa-on-ipv4=yes #publish-a-on-ipv6=no [reflector] #enable-reflector=no #reflect-ipv=no [rlimits] #rlimit-as= rlimit-core=0 rlimit-data=4194304 rlimit-fsize=0 rlimit-nofile=300 rlimit-stack=4194304 rlimit-nproc=3 and here's my sshd_config (mainly updated to only allow pub/private keys): # What ports, IPs and protocols we listen for Port 22 # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel INFO # Authentication: LoginGraceTime 180 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication no AllowGroups sshusers # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM yes Does anyone have any ideas that I can try, or has experienced anything similar?

  Read the article

• Pxe net install Centos with Static IP

  - by Stu2000

  I seem to be unable to perform a kickstart installation of centos5.8 with a netinstall. It correctly gets into the text installer, but keeps sending out a request for the dhcp server and failing. I have tried to manually set the IP everywhere. Here is my pxelinux.cfg file DEFAULT menu PROMPT 0 MENU TITLE Ubuntu MAAS TIMEOUT 200 TOTALTIMEOUT 6000 ONTIMEOUT local LABEL centos5.8-net kernel /images/centos5.8-net/vmlinuz MENU LABEL centos5.8-net append initrd=/images/centos5.8-net/initrd.img ip=192.168.1.163 netmask=255.255.255.0 hostname=client101 gateway=192.168.1.1 ksdevice=eth0 dns=8.8.8.8 ks=http://192.168.1.125/cblr/svc/op/ks/profile/centos5.8-net MENU end and here is my kickstart file: # Kickstart file for a very basic Centos 5.8 system # Assigns the server ip: 192.211.48.163 # DNS 8.8.8.8, 8.8.4.4 # London TZ install url --url http://mirror.centos.org/centos-5/5.8/os/i386 lang en_US.UTF-8 keyboard us network --device=eth0 --bootproto=static --ip=192.168.1.163 --netmask=255.255.255.0 --gateway=192.168.1.1 --nameserver=8.8.8.8,8.8.4.4 --hostname=client1-server --onboot=on rootpw --iscrypted $1$Snrd2bB6$CuD/07AX2r/lHgVTPZyAz/ firewall --enabled --port=22:tcp authconfig --enableshadow --enablemd5 selinux --enforcing timezone --utc Europe/London bootloader --location=mbr --driveorder=xvda --append="console=xvc0" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work part /boot --fstype ext3 --size=100 --ondisk=xvda part pv.2 --size=0 --grow --ondisk=xvda volgroup VolGroup00 --pesize=32768 pv.2 logvol swap --fstype swap --name=LogVol01 --vgname=VolGroup00 --size=528 --grow --maxsize=1056 logvol / --fstype ext3 --name=LogVol00 --vgname=VolGroup00 --size=1024 --grow %packages @base @core @dialup @editors @text-internet keyutils iscsi-initiator-utils trousers bridge-utils fipscheck device-mapper-multipath sgpio emacs Here is my dhcp file: ddns-update-style interim; allow booting; allow bootp; ignore client-updates; set vendorclass = option vendor-class-identifier; subnet 192.168.1.0 netmask 255.255.255.0 { host tower { hardware ethernet 50:E5:49:18:D5:C6; fixed-address 192.168.1.163; option routers 192.168.1.1; option domain-name-servers 8.8.8.8,8.8.4.4; option subnet-mask 255.255.255.0; filename "/pxelinux.0"; default-lease-time 21600; max-lease-time 43200; next-server 192.168.1.125; } } Is it impossible to prevent it asking for a dynamic ip before trying to install from the net? Perhaps there is an error in of my files? My dhcp server is set to ignore client-updates, and is set to only works with one mac address whilst testing.

  Read the article

• SSH: Port Forwarding, Firewalls, & Plesk

  - by Kian Mayne

  I edited my SSH configuration to accept connections on Port 213, as it was one of the few ports that my work firewall allows through. I then restarted sshd and everything was going well. I tested the ssh server locally, and checked the sshd service was listening on port 213; however, I still cannot get it to work outside of localhost. PuTTY gives a connection refused message, and some of the sites that allow check of ports I tried said the port was closed. To me, this is either firewall or port forwarding. But I've already added inbound and outbound exceptions for it. Is this a problem with my server host, or is there something I've missed? My full SSH config file, as requested: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 Port 213 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• How to Configure Source NAT (Private IP => Public IP Outbound)

  - by DavidScherer

  I'm running VMWare ESXi Free and have Zentyal SBS 3.2 running as a Gateway. I have 5 Public IPS (CIDR/29, let's call them 69.1.1.1 - 69.1.1.5) and currently Zentyal is bound to 69.1.1.1 as the Gateway, with the other 4 Public IPs set as Virtual Interfaces in Zentyal (wan2-wan5) I have machines sitting on the Private Network (10.34.251.x) that, when going Outbound (to Google for instance) should be seen by the Internet as an IP other than the Gateway (69.1.1.1), this is because our machines need to be able to communicate with 3rd party APIs that expect these requests to come from a specific IP. From what I could find, SNAT (Source NAT) in Zentyal is used to achieve this, but I'm not sure how to configure it and cannot find a specific piece of Documentation for it at Zentyal. I've tried setting this up a couple different ways, with no results and at this point I have no idea if I'm going about this completely wrong, or my lack of experience with networking and the associated terminology is preventing me from placing the correct values in the correct fields. I get the following form to set up "SNAT" rules in Zentyal: Perhaps someone can offer some guidance and definitions for the fields above? SNAT Address Is this the Public IP I want to masquerade? Outgoing Interface Should this by my External NIC (one connected to Public 'Net), or is it the "Private" interface? It sounds as though this should be the External interface as I want the traffic from the internal network sent Out over this Interface (using a different IP than normal, anyway) Source Is the the Source on the internal network (one of the private IPs?), a public IP I want to masquerade as, or something else entirely? Destination Is this a place on the Internet (eg, "Only do this for the Site Google.com"/IP) or am I allowing myself to become confused again? Service I'm assuming this allows me to restrict which services this rule will apply to, but is it for a service on the internal network or a service being accessed on the external network? If I can offer any further details or information to make what I'm trying to do more clear, I will happily do so. Honestly any kind of help here would be very appreciated. I'm not a NetOps or anything even close, I spend most of my day writing code and my entire "team" at this company consists of "me, myself, and I" so while I try to broaden my KB at every possible opportunity, I can only learn so much, so fast and I feel like with networking especially there's just so much, coupled with a learning curve for each solution that likes to (from my limited perspective) use slightly different terminology that what I'm used to (and I don't exactly have the necessary experience to cross reference this stuff with the stuff I already know in context).

  Read the article

• Windows server detected error with hard disk

  - by user53864

  We have hosting Windows server 2008 R2 and I am working as admin in small company. The server is hanging and restarting as the hard disk seems to be damaged due to power fluctutaion(though having inverter) as it's showing the below error message on server reboot: Problem detected with the hard disk Press any key to continue It's Seagate 1TB SATA hard disk and it's booting after pressing enter. So it's clear that the hard disk is dying. Yes, it's in warranty but it's fact that warranty won't recover the lincesed windows server 2008 and it's data. As it's booting now, I backed up required things and I am thinking to clone the entire hard disk. The first thing it striked me is checking on the Seagate site if any tool available for cloning and I found Seagate DiskWizard but not specified it for windows server 2008. Please anybody could help me giving your best ideas for the below: Urgently, What's the best way(free of cost) for me to clone in my case with the new same sized hard disk? It's a one time lincenced and I cannot use the same key again if I reinstall the server. Will the lincense be carried with new disk if cloned? else there is a way to contact Microsoft explaining the problem occurred, to obtain new key for no charge?. I want to take measure for future. How do I keep two disks in continuous sync? mirrored & raid are the only options converting the disks to dynamic? or is there a best way I could do with no additional charge?. Any help is greatly appreciated. Thank you! EDIT:1 I started cloning the disk with CloneZilla and it was going proper showing in GUI. But after some time there is no GUI but a black screen with some codes(looks like disk location numbers) going page by page(I have attached the screenshots below captured from my phone). Do you people think it's actually cloning?. I started in the morning and it's evening now. I left the office now to let it finish what it's trying to do and I'll go & check it tomorrow. Slowly lost hope, don't know what face it's going to show tomorrow. Any ideas?

  Read the article

• Need advice on which PCI SATA Controller Card to Purchase

  - by Matt1776

  I have a major issue with the build of a machine I am trying to get up and running. My goal is to create a file server that will service the needs of my software development, personal media storage and streaming/media server needs, as well as provide a strong platform for backing up all this data in a routine, cron-job oriented German efficiency sort of way. The issue is a simple one - all my drives are SATA drives and my motherboard controller only contains 4 ports. Solving the issue has proven to be an unmitigated nightmare. I would like advice on the purchase of the following: 4 Port internal SATA / 2 Port external eSATA PCI SATA Controller Card that has the following features and/or advantages: It must function. If I plug it in and attach drives, I expect my system to still make it to the Operating System login screen. It must function on CentOS, and I mean it must function WELL and with MINIMAL hassle. If hassle is unavoidable, there shall be CLEAR CUT and EASY TO FOLLOW instructions on how to install drivers and other supporting software. I do not need nor want fakeRAID - I will be setting up any RAID configurations from within the operating system. Now, if I am able to find such a mythical device, I would be eternally grateful to whomever would be able to point me in the right direction, a direction which I assume will be paved with yellow bricks. I am prepared to pay a considerable sum of money (as SATA controller cards go) and so paying anywhere between 60 to 120 dollars will not be an issue whatsoever. Does such a magical device exist? The following link shows an "example" of the type of thing I am looking for, however, I have no way of verifying that once I plug this baby in that my system will still continue to function once I've attached the drives, or that once I've made it to the OS, I will be able to install whatever drivers or software programs I need to make it work with relative ease. It doesn't have to be dog-shit simple, but it cannot involve kernels or brain surgery. http://www.amazon.com/gp/product/B00552PLN4/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B003GSGMPU&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=1HJG60XTZFJ48Z173HKY So does anyone have a suggestion regarding the subject I am asking about? PCI SATA Controller Cards? It would help if you've had experience with the component before - that is after all why I am asking here - for those who have had experience that I do not have. Bear in mind that this is for a home setup and that I do not have a company credit card. I have a budget with a 'relative' upper limit of about $150.00.

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• Some questions regarding Hostname

  - by user481913

  I just bought a new VPS hosting plan and i have a few questions. Hope someone here can clear the doubts for me. 1) Is it necessary to have a real domain for a vps hostname? I suppose i can just use a non-real domain like anydomain.com and something like 'server' for the computer name. Therefore i'll end up with something like server.anydomain.com as the vps's hostname. I want to do this for the sake of putting in a hostname to configure the vps to get it going . So, since this non-real domain name does not need to be publicly accessible i don't need to register or own it and instead access the server by the ip address. Is that correct? But i suppose that this also depends upon if my web host allows that? 2)I would also like to run some real sites with real domain names on this vps, so can i just configure the zone file on the primary nameserver and make entries for these domains and point an A record at the Vps's IP to make them publicly accessible over the internet? For example for my 1st domain i could make an entry like this: $TTL 86400 mydomain1.com. IN SOA ns1.mywebhost.com. \ admin.mydomain1.com. ( 2004011522 ; Serial no., based on date 21600 ; Refresh after 6 hours 3600 ; Retry after 1 hour 604800 ; Expire after 7 days 3600 ; Minimum TTL of 1 hour ) server IN A 200._._._ ns1.mywebhost.com. IN A 216._._._ ns2.mywebhost.com. IN A 205._._._ @ IN NS ns1.mywebhost.com. @ IN NS ns2.mywebhost.com. @ IN MX 10 server www IN CNAME server server IN CNAME @ (so this particular line tells the nameserver to point the url mydomain1.com to server.anydomain.com at the particular ip addresss in the A record.... is that right?) Similarly for my 2nd domain i could have a similar entry : $TTL 86400 mydomain2.com. IN SOA ns1.mywebhost.com. \ admin.mydomain2.com. (..... ............................so on........ ......................................... ......................................... ......................................... ......................................... ......................................... Is that correct? 3) Suppose for my vps hostname, i ignorantly chose a domain that someone else alreadys owns , however i think that it won't affect the public accessibility of the real domain or website since only the real owner of the domain has the rights to provide for the nameservers addresses in the TLD registeries through his Domian Registerar? Is that correct? 4)Can i change my vps's hostname later? Would this create any complications?

  Read the article

• Switch flooding when bonding interfaces in Linux

  - by John Philips

  +--------+ | Host A | +----+---+ | eth0 (AA:AA:AA:AA:AA:AA) | | +----+-----+ | Switch 1 | (layer2/3) +----+-----+ | +----+-----+ | Switch 2 | +----+-----+ | +----------+----------+ +-------------------------+ Switch 3 +-------------------------+ | +----+-----------+----+ | | | | | | | | | | eth0 (B0:B0:B0:B0:B0:B0) | | eth4 (B4:B4:B4:B4:B4:B4) | | +----+-----------+----+ | | | Host B | | | +----+-----------+----+ | | eth1 (B1:B1:B1:B1:B1:B1) | | eth5 (B5:B5:B5:B5:B5:B5) | | | | | | | | | +------------------------------+ +------------------------------+ Topology overview Host A has a single NIC. Host B has four NICs which are bonded using the balance-alb mode. Both hosts run RHEL 6.0, and both are on the same IPv4 subnet. Traffic analysis Host A is sending data to Host B using some SQL database application. Traffic from Host A to Host B: The source int/MAC is eth0/AA:AA:AA:AA:AA:AA, the destination int/MAC is eth5/B5:B5:B5:B5:B5:B5. Traffic from Host B to Host A: The source int/MAC is eth0/B0:B0:B0:B0:B0:B0, the destination int/MAC is eth0/AA:AA:AA:AA:AA:AA. Once the TCP connection has been established, Host B sends no further frames out eth5. The MAC address of eth5 expires from the bridge tables of both Switch 1 & Switch 2. Switch 1 continues to receive frames from Host A which are destined for B5:B5:B5:B5:B5:B5. Because Switch 1 and Switch 2 no longer have bridge table entries for B5:B5:B5:B5:B5:B5, they flood the frames out all ports on the same VLAN (except for the one it came in on, of course). Reproduce If you ping Host B from a workstation which is connected to either Switch 1 or 2, B5:B5:B5:B5:B5:B5 re-enters the bridge tables and the flooding stops. After five minutes (the default bridge table timeout), flooding resumes. Question It is clear that on Host B, frames arrive on eth5 and exit out eth0. This seems ok as that's what the Linux bonding algorithm is designed to do - balance incoming and outgoing traffic. But since the switch stops receiving frames with the source MAC of eth5, it gets timed out of the bridge table, resulting in flooding. Is this normal? Why aren't any more frames originating from eth5? Is it because there is simply no other traffic going on (the only connection is a single large data transfer from Host A)? I've researched this for a long time and haven't found an answer. Documentation states that no switch changes are necessary when using mode 6 of the Linux interface bonding (balance-alb). Is this behavior occurring because Host B doesn't send any further packets out of eth5, whereas in normal circumstances it's expected that it would? One solution is to setup a cron job which pings Host B to keep the bridge table entries from timing out, but that seems like a dirty hack.

  Read the article

• Mysql Servers for Attendance System

  - by foo

  I'm building an attendance system. There are about 20 places where people will check in and check out using Mifare 1K Card. It will use MySQL as the database. The system will display something like "#ID IN: 800AM" when the first time the user checks in and "#ID OUT: 400PM" when the user checks out. For this to work, all the databases need to be synchronized with each other all the times. For an example, if user A went to location #1 to check in but by the time he wants to return home, the server at location #1 went down, he needs to go to location #2 or the nearest server to check out. The server at location #2 should display '#ID OUT: 400PM" and not "#ID IN: 400PM" since he's already checked in. So, what should I use to ensure this idea will work? My main concern is with the network (other department manages it) which is very unpredictable. It just love to go down anytime it wants to. Update LOL, didn't realize my question is not clear, just noticed it when you guys pointed it out, sorry about that. My real question is, how can I configure my MySQL to be synchronized with each other (20 servers)? MySQL cluster ? (tried reading about it, but I'm not sure if it's the right thing to do) My current setup (first phase): Local database for each server OS: Slackware A main server that keeps track which staff is at which server A web based front end for the user to see their history (which connects to the server based on their records) Main Pros No worries about network problems since it is a local database Main Cons A user can only check in and out at the same server. Databases/Servers are not connected with each others. Have to add the user to each server if the users want to check in at different locations. Which means, if he wants to go to location A, he must be checked out from location A first and then check in at location B. The server at location B didn't know that the user has checked in before at A. By the way, I've already centralized my NTP to a local server. About the network, let's just say, I don't have the authority to make changes so that the network will be better. The network won't effect all 20 servers at once, usually, just a few of them for several times a week. If there are anything else you would like me to answer, please just ask.

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• How to setup GIT repo on server with need for working dir (non- bare)

  - by OrangeTux

  I want to have configurate a GIT repo for a website. Multiple users will have a clone of the repo on their local machine and on the end of each day they push their work to the server. I can setup a bare repo, but I want a working dir/non-bare repository. The idea is that the working dir of the repository will the root folder for the website. At the end of each day all changes will be visible directly. But I can't find a way to do this. Initializing the server repo with git init gives the following error when a client is trying to push some files: git push origin master [email protected]'s password: Counting objects: 3, done. Writing objects: 100% (3/3), 227 bytes, done. Total 3 (delta 0), reused 0 (delta 0) remote: error: refusing to update checked out branch: refs/heads/master remote: error: By default, updating the current branch in a non-bare repository remote: error: is denied, because it will make the index and work tree inconsistent remote: error: with what you pushed, and will require 'git reset --hard' to match remote: error: the work tree to HEAD. remote: error: remote: error: You can set 'receive.denyCurrentBranch' configuration variable to remote: error: 'ignore' or 'warn' in the remote repository to allow pushing into remote: error: its current branch; however, this is not recommended unless you remote: error: arranged to update its work tree to match what you pushed in some remote: error: other way. remote: error: remote: error: To squelch this message and still keep the default behaviour, set remote: error: 'receive.denyCurrentBranch' configuration variable to 'refuse'. To ssh://[email protected]/home/orangetux/www/ ! [remote rejected] master -> master (branch is currently checked out) error: failed to push some refs to 'ssh://[email protected]/home/orangetux/www/' So I'm wondering if this the right way to setup a GIT repo for a website? If so, how do I have to do this? If not, what is a better way to setup a GIT repo for the development of a website? EDIT you can't push to a non-bare repository Oke, clear. But whats the way to solve my problem? Create a bare repository on the server and have a clone of this repo on the same server in the htdocs folder? This looks a bit clumsy to me. To see the result of a commit I've to clone the repository each time.

  Read the article

• Synchronize the same set of files to 2 different locations with 2 different programs for 2 different purposes

  - by Hedgetrimmer

  Because of stupid questionable IT policies at my not-to-be-named place of occupation, I have been (and will be, for the forseeable future) carrying on an external hard drive a unison-synchronized copy of all of my documents and code, including code which resides in some of my "dotfiles" and other code which resides in ~/bin (things I've made are there because ~/bin is in my $PATH) along with some cruft generated (and to be generated) by conscript and its related "giter8" templating system for Scala project boilerplates. Despite this, I do use a symlinking program to store all of my important dotfiles in a subdirectory. Thanks to that somewhat complicated setup, I have resorted to making a directory full of symlinks to every directory (or file, as is the case with stuff under ~/bin) that I want synchronized, and then follow = True is in my unison profile. It happens to be that this collection of odds and ends—plus an automatically-generated text file containing every package installed on my system—is everything under ~ that needs to be backed up to a remote (rsync-over-ssh) host with client-side encryption and signing from GPG. I already believe that duplicity is the most appropriate program to do that. What isn't as clear-cut is how to make duplicity use the exact same set of files when it runs a backup; it would be simple if duplicity would follow symlinks, but it does not and the manpage lists no option for enabling any such behavior. Comparing unison's file selection algorithm to duplicity's, I don't think I can write a program that could compute a ruleset for one program given one for the other. For the record, I would rather not keep the symlinks manually synchronized with duplicity file-selection rules, as they can change thanks to the above-mentioned complications regarding ~/bin. I don't think running duplicity on the external hard disk is such a good idea either; I usually keep that hard disk unmounted and unplugged in case of a power failure or other physical problem with the computer, plus I'm not sure about duplicity's performance given that: the hard disk is NTFS-formatted in order to be useable at my Windows-imprisoned place of occupation. despite being a USB 3.0 disk, my computer has no USB 3.0 ports so it acts as a USB 2.0 disk. How can I have duplicity (or is there a better program that I have overlooked?) back up the exact same set of files that is bidirectionally synchronized with my external hard disk?

  Read the article

• Creating a network link between 2 very close buildings

  - by Daniel Johnson

  I have a charity who have two adjacent medium sized modern detached houses (in the UK): the buildings stand next to each other and are less than 5 metres apart. They have DSL connected to a single computer in one of the buildings. They want to add a network with wireless, and want it to work across both buildings. Being a charity they need to keep costs down. The network would be used for sharing Word documents, e-mail, browsing and skyping. My initial thoughts were to connect the buildings with fibre. So: Option 1 Use fibre between the buildings. Sufficient cable and two TP-LINK MC100CM Fast Ethernet Media Converters. Cost ~£80.00. But there is the extra cost and hassle of running the cable down and up the external walls, lifting and relaying paving, and burying underground. Never having fitted fibre I'm also a little worried about going up the wall and then bending the cable at 90 degrees to go through the wall and into the building. Option 2 Use two TP-Link TL-WA7510N High Powered Outdoor 5Ghz 15dBi Wireless antennas to connect the buildings. There is a clear line of sight at first floor level. Cost ~£100. And much easier to fit than fibre! Is using the TL-WA7510Ns overkill? Is there something more suitable? I had hoped to use some Netgear stuff, e.g. two DGN2200, one in each house and also use them to provide the wireless link between the buildings. However, in bridge mode wireless client association is not available and repeater mode with client association only supports WEP security which isn't strong enough. Is there something similar that would be up to the job? Option 3 Connect the buildings with UTP cable. My concerns here are risk of electric shock due to a difference of potential between the buildings (or are they so close this shouldn't be an issue) and protection from lightning strikes. Is fitting lighting arrestors expensive? And what can be done to ameliorate against the risk of shock? This all falls outside my area of expertise so I would really appreciate some advice.

  Read the article

< Previous Page | 358 359 360 361 362 363 364 365 366 367 368 369  | Next Page >